Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Configuration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Fuel cells for single-aisle regional aircraft: System configuration, performance and cost

A hydrogen fuel cell propelled electric aircraft can compete with incumbent turbofan technologies for single-aisle regional aircraft by coupling design of stack, air handling, thermal management, propulsion, and airframe to optimize performance. The stack operates at 95°C to facilitate heat rejection during take-off and below 75°C during cruise to extend lifetime and is oversized to satisfy power requirements at end of life. A multi-stage turbocompressor with a compression ratio >10 is selected to reach high stack power density at 11,300-m cruise altitude. The propulsion system is configured to accommodate air handling within the core duct, an inclined heat exchanger in the outer duct to limit the nacelle size, and variable area nozzles to independently control mass flows through the core and bypass ducts. The airframe is modified for maximum lift coefficient and longer balanced field length for dramatically reduced thrust during take-off, and the fuselage is stretched by 20% to store liquid hydrogen (LH 2 ). Modularization of power systems promotes safety in one engine inoperative scenarios and allows reaching specific power metrics for stack, balance-of-plant and fuel cell system (FCS), necessary for acceptable take-off weight. In conclusion, cost parity requires increase in FCS lifetime, LH 2 cost reduction, and improved FCS specific power.

Catalyst durability↗
DOE OSTI2020

Assessment of reverse gun taylor cylinder experimental configuration

Experimental efforts for Taylor-anvil impact tests have often been limited to near room temperature. The ‘Reverse Gun’ method proposed by Gust in 1982 allows for the Taylor impact specimen to be uniformly heated without temperature losses before impact. Through the use of finite element analysis, we explore two topics in this work. First, we examine whether the reverse gun experimental configuration is comparable to the traditional Taylor-anvil setup. Second, we assess the accuracy of several commonly employed flow strength models in terms of their ability to predict the reverse gun experimental results which involve dynamic loading conditions and complex thermo-mechanical coupling. The reverse gun simulations are performed for tantalum targets at initial temperatures in the range 295 K to 1295 K and velocities from 135 m/s to 242 m/s. We show that with suitable care in the modeling of the preheated reverse gun experiments one can make valuable assessments of flow strength models. Given the conditions explored, these observations probe the thermal softening, strain hardening, and strain rate sensitivity of the material.

42 ENGINEERING↗
DOE OSTI2024

Assessing microbial systems and process configurations for improved ethanol production from sugary stovers by integrating soluble sugars and holocellulose

Here, this study evaluated microbial systems and technological approaches to configure the whole slurry co-fermentation process for ethanol biosynthesis from a novel stover system rich in sugars. Two approaches, namely separate and simultaneous hydrolysis and co-fermentation (SHCF and SSCF, respectively), were investigated using Escherichia coli monoculture and E. coli-yeast coculture. The SSCF with E. coli monoculture produced 32.75 g/L ethanol, representing only 44.87% yield, which left 65.13 g/L of total sugars unconverted and exhibited limited xylose consumption. Subsequently, a coculture-based SHCF significantly enhanced sugar consumption, leading to increase in ethanol yield and concentration to 66.94% and 48.86 g/L, respectively. Nevertheless, xylose utilization remained minimal due to the preference for glucose and the inhibitory effects of certain compounds. Thereafter, modification of the medium composition by supplementing betaine and sodium metabisulfite improved ethanol production to 53.18 g/L by reducing the toxic effects of inhibitors. Finally, a dual-phase SSCF (DP-SSCF) was explored by allowing the consumption of sugars from the pretreated slurry in the first phase, followed by concurrent cellulose hydrolysis and utilization of the resulting glucose in the second phase. This strategy increased ethanol titer to 63.14 g/L, with 84.3% yield and 0.88 g/L/h productivity.

09 BIOMASS FUELS↗
DOE OSTI2022

Augmented Adam-Gibbs model for glass melt viscosity and configuration entropy as functions of temperature and composition

As the temperature of glass melt increases, its structure approaches the state of a simple liquid while the configuration entropy approaches a maximum value. We describe this gradual change using a power law function of inverse temperature. The Adam-Gibbs model for glass viscosity as a function of temperature and glass composition augmented in this way is greatly simplified when applied to common glass families occupying moderate composition regions, such as float glass or nuclear waste glasses, on which properties can be approximated as linear functions of composition. The parsimonious model thus obtained is preferable for use in optimizing glass formulation and mathematical modeling of glass melting and forming. For multicomponent glasses with N viscosity-affecting components, the augmented Adam-Gibbs model requires 2N + 3 adjustable parameters. The model efficacy is demonstrated by fitting the model to a viscosity-temperature-composition dataset for low-activity nuclear waste glasses.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2014

Analysis of hydrogen adsorption and surface binding configuration on tungsten using direct recoil spectrometry

In our work, we apply low energy ion beam analysis to examine directly how the adsorbed hydrogen concentration and binding configuration on W(1 0 0) depend on temperature. We exposed the tungsten surface to fluxes of both atomic and molecular H and D. We then probed the H isotopes adsorbed along different crystal directions using 1–2 keV Ne + ions. At saturation coverage, H occupies two-fold bridge sites on W(1 0 0) at 25 °C. Moreover, the H coverage dramatically changes the behavior of channeled ions, as does reconstruction of the surface W atoms. For the exposure conditions examined here, we find that surface sites remain populated with H until the surface temperature reaches 200 °C. Then, we observe H rapidly desorbing until only a residual concentration remains at 450 °C. Development of an efficient atomistic model that accurately reproduces the experimental ion energy spectra and azimuthal variation of recoiled H is underway.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2016

Configurations, band structures and photocurrent responses of 4-(4-oxopyridin-1(4H)-yl)phthalic acid and its metal-organic frameworks

4-(4-oxopyridin-1(4 H)-yl)phthalic acid (H{sub 2}L) and three H{sub 2}L-based metal-organic frameworks (MOFs) formulated as ZnL(DPE)(H{sub 2}O)·H{sub 2}O (DPE=(E)-1, 2-di(pyridine −4-yl)ethene) (1), CdL(H{sub 2}O){sub 2} (2) and CdL (3) were synthesized and structurally characterized by single-crystal X-ray diffraction. The free H{sub 2}L ligand shows an enol-form and the L{sup 2−} ligand in the three MOFs exists as the keto-form. Density functional theory (DFT) calculations indicate H{sub 2}L and the three MOFs possess different band structures. Due to the existence of the N-donor, DPE in MOF 1, the conduction band (CB) minimum and band gap of MOF 1 are much lower than those of H{sub 2}L. And MOF 1 yielded much larger photocurrent density than H{sub 2}L upon visible light illumination. Electrochemical impedance spectroscopy (EIS) shows the interfacial charge transfer impedance in the presence of MOF 1 is lower than that in the presence of H{sub 2}L. The hydrous MOF 2 and the anhydrous MOF 3 are both constructed by Cd(II) and L{sup 2−}, and they can be reversibly transformed to each other. However, MOFs 2 and 3 possess different CB minimums and VB maximums, and their band gaps are much larger than that of MOF 1. - Graphical abstract: The free ligand, 4-(4-oxopyridin-1(4H)-yl)phthalic acid (H{sub 2}L) shows different configuration from its three MOFs, and they possess different band structures. MOF 1 yielded much larger visible-light-driven photocurrent density than H{sub 2}L. The hydrous MOF 2 and the anhydrous MOF 3 can be transformed to each other, and they have larger band gaps than MOF 1.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2017

Characterizing dislocation configurations and their evolution during creep of a new 12% Cr steel

Highlights: • Applicability of different techniques to characterize particular dislocation configuration. • XRD models in combination with TEM and EBSD to measure the dislocation density. • Substructure evolution during creep of a new 12% Cr steel is discussed. - Abstract: In this research, different types of dislocations are characterized and quantified in a newly developed 12% Cr steel in as-received as well as in crept conditions. X-ray diffraction (XRD) patterns are analyzed using three different models. The dislocation densities are determined employing the Convolution Multiple Whole Profile (CMWP) fitting, the analysis of the asymptotic part of the X-ray line profile (Groma's method), and the Rietveld refinement coupling Popa's and Williamson-Smallman approaches. CMWP method is used to measure the internal dislocation density inside the subgrains consisting of mobile and dipole dislocations, and the results show good agreement with Transmission Electron Microscopy (TEM) measurements. Groma's method is used to evaluate the total dislocation density, with results comparable to those obtained from the combination of Electron Backscatter Diffraction (EBSD) and TEM. Rietveld method gives the internal dislocation density or mobile dislocation density depending on the model chosen. The experimentally determined results such as creep strain, dislocation densities and subgrain size are compared with theoretical predictions and they are found in good agreement.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Analysis of dislocation configurations in SiC crystals through X-ray topography aided by ray tracing simulations

Silicon carbide as a wide bandgap semiconductor is of great research interest for its widespread deployment in a range of electronic and optoelectronic devices, particularly in power electronics. However, defects in silicon carbide crystals are still major concerns that is hampering the development of high-performance devices. X-ray topography, particularly using the synchrotron beam has been instrumental in characterizing and analyzing defect configurations in silicon carbide crystals to optimize crystal growth as well as understand the effect of defects on device performance. Here, in recent years, the use of ray-tracing simulation technique based on the orientation contrast mechanism to simulate contrast of defects observed on actual X-ray topographs has proven to be an effective approach to investigate the nature of crystallographic defects in various semiconductors. This review discusses the principle of ray-tracing simulation and its application and modifications to incorporate the effects of surface relaxation and photoelectric absorption to better simulate different dislocations observed in 4H–SiC as well as 6H–SiC crystals of various orientations. The adaptation to weak beam topography and plane wave topography is also discussed. The application of ray-tracing simulation in dislocation characterization of silicon carbide of different polytypes is systematically reviewed including different types of dislocations observed in both off-axis wafers and axial-sliced samples through synchrotron X-ray topography under various beam conditions, recording geometries and reflections. The result of ray-tracing simulation is further utilized in other studies including the investigation of effective penetration depth of all types of dislocations lying on the basal plane on grazing-incidence X-ray topography.

Engineering↗
DOE OSTI2021

Configuration and impurity quantification of AmLi sources using radiography and gamma spectroscopy

This paper presents the non-destructive assay of two AmLi sources used for detector characterization and active interrogation at PNNL, identified as MRC-101 and MRC-103. First, a detailed description of the internal configuration of 2724-BT encapsulated MRC sources is established. X-ray radiographs of the AmLi sources are reported for the first time to verify the dimensions and orientation of the encapsulation. Notably, a density variation was observed as a contrast change across the height of the source cavities. Contrary to commonly made assumptions in literature, it is indirectly observed that the AmLi source/target material only occupies a portion of the source cavity. The intensity of the prompt gamma-rays resulting from the inelastic scatter of alpha particles on 7Li was used to calculate the mass ratios of LiH:AmO2. The gamma-ray spectra revealed the presence of numerous impurities in both source and target material (243Am, 237Np, 154Eu, 23Na, and 9Be). Neutron-gamma production ratios were applied to the intensity of the Doppler-broadened peaks from alpha-induced reactions with 7Li, 9Be, and 23Na to calculate neutron rates for both sources. A neutron/alpha production yield (derived in this work) was then related to the atomic concentration of these isotopes to find the approximate masses within each source. Ultimately, the AmLi source density was estimated with prompt gamma analysis based on partial source volumes as 0.45±0.08 g/cm^3.

DTRA, AmLi, neutron↗
DOE OSTI2024

Evolution of the two-neutron configuration from 11 Li to 13 Li

In this work we investigate the two-neutron decay of 13 Li and of the excited states of 11 Li populated via one-proton removal from 14 Be and 12 Be, respectively. A phenomenological model is used to describe the decay of 11 Li and 13 Li. While the first one displays important sequential components, the second one appears dominated by the direct two-neutron decay. A microscopic three-body model is used to extract information on the spatial configuration of the emitted neutrons before the decay and shows that the average distance between the neutrons increases going from 11 Li to 13 Li.

Dineutron decay↗
DOE OSTI2018

Propagation of a stable gaseous detonation in a circular arc configuration

Here, we examine numerically the effect that detonation wavefront curvature has on gaseous detonation cellular structure in a circular arc geometry with rigid walls. For the model considered, a planar detonation is weakly unstable. The detonation curvature is induced by diffraction and flow divergence as the wave sweeps around the arc. We examine the effect of arc thickness, inner arc radius and activation energy on the cellular pattern. A combination of pseudo-Schlieren, pseudo-soot foil records and detonation shock and sonic flow loci are used to explore the observed detonation structures. We find that for sufficiently wide arcs, the detonation wavefront curvature renders the detonation hydrodynamically stable, i.e. laminar flow with no cells. The stable configuration consists of a broadly curved wave originating from the inner arc surface, which is typically connected to the outer arc boundary by a stable Mach stem. The stable detonation is driven by a small region of subsonic flow attached to the inner arc surface, outside of which the flow is supersonic. The initiation dynamics of a stable propagating wave case are explored. The evolution dynamics between an unstable (cellular) and stable arc thickness are also examined. Finally, smaller inner arc radii and lower activation energies increase the range of stable solutions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Accelerating the discovery of low-energy structure configurations: A computational approach that integrates first-principles calculations, Monte Carlo sampling, and Machine Learning

Finding Minimum Energy Configurations (MECs) is essential in fields such as physics, chemistry, and materials science, as they represent the most stable states of the systems. In particular, identifying such MECs in multi-component alloys considered candidate PFMs is key because it determines the most stable arrangement of atoms within the alloy, directly influencing its phase stability, structural integrity, and thermo-mechanical properties. However, since the search space grows exponentially with the number of atoms considered, obtaining such MECs using computationally expensive first-principles DFT calculations often results in a cumbersome task. To escape the above compromise between physical fidelity and computational efficiency, we have developed a novel physics-based data-driven approach that combines Monte Carlo sampling, first-principles DFT calculations, and Machine Learning to accelerate the discovery of MECs in multi-component alloys. More specifically, we have leveraged well-established Cluster Expansion (CE) techniques with Local Outlier Factor models to establish strategies that enhance the reliability of the CE method. In this work, we demonstrated the capabilities of the proposed approach for the particular case of a tungsten-based quaternary high-entropy alloy. However, the method is applicable to other types of alloys and enables a wide range of applications.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Supercritical Carbon Dioxide Power Cycle Design and Configuration Optimization to Minimize Levelized Cost of Energy of Molten Salt Power Towers Operating at 650 °C

This analysis investigates the design, cost, and performance of the simple, recompression, and partial-cooling configurations of the supercritical carbon dioxide power cycle integrated with a molten salt power tower concentrating solar power system. This paper uses a steady-state model to design each cycle with varying amounts of recuperator conductance to understand performance and cost trade-offs. The recompression cycle can achieve a higher thermal efficiency than the partial-cooling cycle, and the partial-cooling cycle achieves a higher thermal efficiency than the simple cycle. The partial-cooling cycle is the most expensive cycle because it requires more total turbomachinery capacity. However, the partial-cooling cycle has the largest temperature range of heat input. This feature leads to cheaper two-tank thermal energy storage, higher receiver efficiencies, and lower mass flow rates in the power tower. Crucially, the lower mass flow rates significantly reduce pump electricity consumption relative to the recompression-cycle system. Consequently, this study finds that the power tower system integrated with the partial-cooling cycle is both cheaper and generates more net electricity than systems integrated with the other two cycles. Finally, this paper presents a parametric study on the air-cooler approach temperature and shows that small approach temperatures can improve cycle efficiency and increase the temperature range of heat input, which can lead to smaller optimal approach temperatures than may be expected.

14 SOLAR ENERGY↗
DOE OSTI2016

Supramolecular clusters and chains of 2,6-dimethylpyridine on Cu(110): Observation of dynamic configuration change with real-space surface science techniques and DFT calculations

Here, the adsorption of 2,6-dimethylpyridine (2,6-DMP) on Cu(110) has been studied using low temperature scanning tunneling microscopy (LT-STM), time-of-flight electron stimulated desorption ion angular distribution (TOF-ESDIAD), and density functional theory (DFT) calculations. At low temperatures (T < ~ 150 K), the 2,6-DMP adsorbs in a flat configuration on Cu(110) producing clusters and extended domains via weak hydrogen bonding (C—H···N) with the molecular symmetry axis aligned along the < 001 > surface direction.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Oxygen Defect Configurations in Single-Phase UO 2.15

Hyperstoichiometric UO 2.15 was characterized by neutron total scattering at high temperature in the single-phase UO 2+x region of the U/O phase diagram. The diffraction data confirmed a single-phase fluorite structure at high temperature. Analysis of the short-range data showed that the same structural model does not fit the pair distribution functions well. Instead, structural models containing specific configurations of oxygen defect clusters best represent the local atomic arrangement. In conclusion, prevalent defect clusters previously proposed were fit to the experimental data, and moderately distorted oxygen cuboctahedra hypothesized by recent molecular dynamics simulations fit the data most accurately.

neutron pair-distribution function analysis↗
DOE OSTI2025

Ultra-Confined Environments May Restrict the Possible Configurations of Supported Metal Complexes

Here, the rotation frequencies of amido ligands are highly sensitive to the electronic structure of d 0 transition metal complexes and have been used to study ligand donor properties. While attempting to study the donor properties of silanolate ligands in a silica-supported Cr complex, we observed highly restricted motions due to the added steric hindrance from the support, with only approximately half of the amides rotating on a 50 ms time scale. Surprisingly, when the same species is grafted into narrow 2.2 nm pores, all amido ligands are able to rotate. Density functional theory calculations suggest that confinement may limit the possible coordination sites and the configuration of the formed surface species, potentially enabling the formation of conformationally homogeneous surface site populations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Benchmarking an Embedded Adaptive Sampling Configuration Interaction Method for Surface Reactions: H 2 Desorption from and CH 4 Dissociation on Cu(111)

Embedded (emb-) correlated wavefunction (CW) theory enables accurate assessments of both ground- and excited-state reaction mechanisms involved in heterogeneous catalysis. Embedded multireference second-order perturbation theory (emb-MRPT2) based on reference wavefunctions generated via embedded complete active space self-consistent field (emb-CASSCF) theory is currently state-of-the-art. However, the factorial scaling of CASSCF limits the size of active space and the complexity of systems that can be studied. In this work, we assess the efficacy of an alternative CW method, adaptive sampling configuration interaction (ASCI)–which enables large active spaces to be used–for studying surface reactions. We couple ASCI with density functional embedding theory (DFET) and benchmark its performance for two reactions: H 2 desorption from and CH 4 dissociation on the Cu(111) surface. Unlike embedded complete active space second-order perturbation theory (emb-CASPT2) that accurately reproduces a measured H 2 desorption barrier, embedded ASCI, using a very large active space (though one that still comprises a small portion of the full set of orbitals) fails to do so. Adding an extra correlation term from embedded Møller–Plesset second-order perturbation theory (emb-MP2) improves the desorption barrier and endothermicity predictions. Thus, the inaccuracy of embedded ASCI comes from the missing dynamic correlation from the many other electrons and orbitals not included in the active space. For CH 4 dissociation, again embedded ASCI overestimates the dissociation barrier compared to emb-CASPT2 predictions. Adding dynamic correlation from emb-MP2 helps correct the barrier. However, this composite approach suffers from double counting of correlation within embedded ASCI followed by emb-MP2 calculations. We therefore conclude that the state-of-the-art emb-MRPT2 based on reference wavefunctions generated via emb-CASSCF remains the method of choice for studying surface reactions. emb-ASCI is useful when large active spaces beyond the limit of emb-CASSCF are essential, such as to study complex surface reactions with significant multiconfigurational character (static correlation) but weak dynamic correlation.

08 HYDROGEN↗
DOE OSTI2022

GronOR: Scalable and Accelerated Nonorthogonal Configuration Interaction for Molecular Fragment Wave Functions

GronOR is a program package for nonorthogonal configuration interaction calculations. Electronic wave functions are constructed in terms of antisymmetrized products of multiconfiguration molecular fragment wave functions. The computational complexity of the nonorthogonal methodologies implemented in GronOR applied to large molecular assemblies requires a design that takes full advantage of massively parallel supercomputer architectures and accelerator technologies. This work describes the implementation strategy and resulting performance characteristics. In addition to parallelization and acceleration, the software development strategy includes aspects of fault resiliency and heterogeneous computing. The program was designed for large-scale supercomputers but also runs effectively on small clusters and workstations for small molecular systems. GronOR is available as open source to the scientific community.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗