Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Conditional distributions”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

A forward-swept wing configuration designed for high maneuverability by use of three-dimensional transonic theory

Supercritical technology has been applied to the design of a forward-swept-wing fighter configuration, and an assessment has been made of the relative performance of forward versus aft sweep. The wing and canard for this forward-swept wing configuration were designed for transonic maneuver by the use of a transonic computational analysis method and a transonic design procedure. The computational method calculates the transonic flow over a canard-wing-fuselage combination so that the strong transonic induced-flow effects of the canard on the wing are taken into account. A model of this configuration was constructed and was tested in the Langley 16-Foot Transonic Tunnel. The transonic theory gave a reasonably good estimate of the wing pressure distributions at transonic maneuver conditions. Comparison of this configuration with an equivalent aft-swept wing configuration showed that, at a Mach number of 0.9 and a lift coefficient of 0.9, the two configurations have essentially the same drag. This forward-swept wing configuration was also found to have very good maneuver performance relative to the Rockwell International HiMAT highly-maneuverable aircraft configuration.

Mann, M. J.↗
NASA NTRS1986

A nitric oxide increase observed following the July 1982 solar proton event

Following the solar proton event (SPE) of July 13, 1982, an increase in the strength of nitric oxide Gamma bands was observed in spectral scans of the atmospheric albedo made by the solar backscattered ultraviolet instrument on Nimbus 7. Analysis of the (10), (01), and (02) Gamma band strengths allow an estimate to be made of the cumulative amount of nitric oxide above an altitude of 50 km. An increase in nitric oxide in southern hemisphere high latitudes following the SPE amounting to about 5 x 10 to the 14th molecules per sq cm above an altitude of approximately 50 km is observed. The observed increase persists until the middle of September. A similar increase is not observed in the northern hemisphere, indicating that under summer conditions the mesospheric/thermospheric NO distribution returns to normal within a few days after the end of an SPE.

Mcpeters, R. D.↗
NASA NTRS1986

Forward-swept wing configuration designed for high maneuverability by use of a transonic computational method

A transonic computational analysis method and a transonic design procedure have been used to design the wing and the canard of a forward-swept-wing fighter configuration for good transonic maneuver performance. A model of this configuration was tested in the Langley 16-Foot Transonic Tunnel. Oil-flow photographs were obtained to examine the wind flow patterns at Mach numbers from 0.60 to 0.90. The transonic theory gave a reasonably good estimate of the wing pressure distributions at transonic maneuver conditions. Comparison of the forward-swept-wing configuration with an equivalent aft-swept-wing-configuration showed that, at a Mach number of 0.90 and a lift coefficient of 0.9, the two configurations have the same trimmed drag. The forward-swept wing configuration was also found to have trimmed drag levels at transonic maneuver conditions which are comparable to those of the HiMAT (highly maneuverable aircraft technology) configuration and the X-29 forward-swept-wing research configuration. The configuration of this study was also tested with a forebody strake.

Mann, M. J.↗
NASA NTRS1987

Scattering parameters for aspherical hydrometeors at microwave frequencies

Scattering parameters for ensembles of aspherical ice and liquid hydrometeors were calculated at Psi = 50 deg for frequencies of 37.0, 50.3, and 85.6 GHz. Hydrometeors were assumed to be oblate spheroids whose semiminor axes were aligned at Psi = 0 deg. The angle of 50 deg is determined by the viewing angle of recent satellite-borne radiometers. Backscattering phase functions and extinction coefficients at Psi = 0 deg were also computed at 18.0, 37.0, and 85.6 GHz to provide information for future nadir scanning radars. The hydrometeors were assumed to be characterized by Marshall-Palmer (1948) size distributions. The extended boundary condition method was used to calculate the extinction and backscattering coefficients as well as the albedo for single scattering and the asymmetry factor of the phase function. Results are fitted to simple functions of the rainfall rate. Some comparisons intended to illustrate the differences and similarities of these results with those obtained from equal volume spheres are also presented.

Kummerow, C.↗
NASA NTRS1989

Measured and predicted aerodynamic heating on a cylinder in wake of AFE configuration at incidence

Thin-film resistance gages were used to measure cylinder surface heat-transfer rates in the near wake of the Aeroassist Flight Experiment vehicle configuration, while surface-streamline directions were ascertained by the oil-flow techniques under the same configuration and test conditions. Both heat transfer distributions and flow over the entire cylinder surface were influenced by impingement of that portion of the free shear layer originating at the forebody shoulder in the upper symmetry plane. Heating rate distributions predicted with a Navier-Stokes solver computer code were in general agreement with measurements.

Wells, William L.↗
NASA NTRS1990

A comparison of single-cycle versus multiple-cycle proof testing strategies

An evaluation of single-cycle and multiple-cycle proof testing (MCPT) strategies for SSME components is described. Data for initial sizes and shapes of actual SSME hardware defects are analyzed statistically. Closed-form estimates of the J-integral for surface flaws are derived with a modified reference stress method. The results of load- and displacement-controlled stable crack growth tests on thin IN-718 plates with deep surface flaws are summarized. A J-resistance curve for the surface-cracked configuration is developed and compared with data from thick compact tension specimens. The potential for further crack growth during large unload/reload cycles is discussed, highlighting conflicting data in the literature. A simple model for ductile crack growth during MCPT based on the J-resistance curve is used to study the potential effects of key variables. The projected changes in the crack size distribution during MCPT depend on the interactions between several key parameters, including the number of proof cycles, the nature of the resistance curve, the initial crack size distribution, the component boundary conditions (load vs. displacement control), and the magnitude of the applied load or displacement. The relative advantages of single-cycle and multiple-cycle proof testing appear to be specific, therefore, to individual component geometry, material, and loading.

Hudak, S. J., Jr.↗
NASA NTRS1990

Stabilization functions of unforced cumulus clouds - Their nature and components

The nature and the spatial distribution of cumuli within an unforced cumulus cloud field are investigated. The thermodynamic effects of convection are quantified as functions of changes of convective available potential energy (CAPE) induced by the convective overturning, and the time rate of change of CAPE is parameterized in terms of a kernel of influence or stabilization function. A three-dimensional cloud model is used to infer and quantify stabilization functions by performing single-cloud experiments. On the basis of the results obtained, a new hypothesis with respect to the spatial distribution of cumuli is postulated, which states that, under completely homogeneous external conditions and assuming a spatially random distribution of cloud-triggering mechanisms, the spatial distribution of cumuli in the resulting cloud field must be regular, as opposed to either random or clustered, because cumulus clouds tend to reduce the available energy for convection, thereby inhibiting further convection nearby.

Ramirez, Jorge A.↗
NASA NTRS1990

Effect of a prior stretch on the aging response of an Al-Cu-Li-Ag-Mg-Zr alloy

The effect of a prior stretching of an aluminum alloy Al-5.3Cu-1.4Li-0.4Ag-0.4Mg-0.17Zr (in wt pct) on the microstructure that develops during aging of this alloy was investigated by comparing TEM and SAD observations and hardness curves with results for the unstretched alloy. The results suggest that stretching introduces a significant number of dislocations which may act as vacanacy sinks by sweeping vacancies away and thereby decreasing the vacancy concentration available for influencing the natural aging response. In the stretched and near-peak aged condition, a fine homogeneous distribution of T1, theta-prime, and S-prime phases were observed in an alpha solid solution matrix. Upon overaging, virtually all of the theta-prime and most of the S-prime phases were found to dissolve, leaving behind a microstructure of T1 precipitates.

Kumar, K. S.↗
NASA NTRS1990

Fractional cloudiness in shallow cumulus layers

Fractional cloudiness influences the planetary boundary layer (PBL) by controlling the cloud-top radiative cooling rate, and regulating the buoyant production and consumption of turbulence kinetic energy. Betts, Hanson, and Albrecht have modeled partly cloudy PBLs by assuming a single family of convective circulations. The same idealized model has been used in observational studies, based on conditional sampling and/or joint distribution functions, by Lenschow, Albrecht, and others. This approach is extended. None of these authors has proposed a method to determine the fractional area covered by rising motion; finding such a method was a key objective of the present study.

Randall, David A.↗
NASA NTRS1989

CELSS Breadboard Project at the Kennedy Space Center

The CELSS Breadboard Project is described, noting that it was initiated to study aspects of a CELSS for long-term space missions. Topics for extensive investigation included air and water regeneration, engineering control, and food production. The many options available for growing food crops in commercial plant growth chambers were investigated and the best of this information was translated to the Biomass Production Chamber (BPC). The chamber contains 20 sq m of crop growing area under 96 400 W HPS lamps; sixteen 0.25 sq m plant growth trays used on each of four growing shelves for a total of 64 trays; and one 256-L nutrient solution reservoir with the appropriate continuous-flow, thin-film plumbing for each shelf. A heating, ventilating, and air-conditioning system maintains atmospheric conditions and serves to distribute oxygen and carbon dioxide and maintain pressure at 12 mm of water. The control and monitoring subsystem, which uses a programmable logic controller, manages the BPC subsystems.

Prince, R. P.↗
NASA NTRS1991

On the Galactic origin of gamma-ray bursts

Statistical properties of the distribution of gamma-ray bursts (GRBs) are analyzed assuming that bursters are located in the Galactic disk or in the Galactic halo. It is shown that, in almost all models, angular anisotropy as measured with either dipole or quadrupole moments is much stronger and should be much easier to detect than the radial nonuniformity of the source distribution as measured with V/V sub max test. Recent reports that V/V sub max is about 0.4 demonstrate that the 'edge' of GRBs distribution has been reached. Therefore, if the bursters are in the Galaxy, then their distribution in the sky should be very anisotropic, with a large dipole or quadrupole moment for halo or disk origin, respectively. Absence of strong anisotropy would indicate cosmological origin. Another possibility could be a very extended halo origin, with the core radius Rc greater than 17 kpc, the range of observations Dmax greater than 50 kpc, and a spherical density distribution, the set of conditions that would be very difficult to understand.

Paczynski, Bohdan↗
NASA NTRS1992

Solution strategies and heat transfer calculations for three-dimensional configurations at hypersonic speeds

A procedure which reduces the memory requirements for computing the viscous flow over a modified Orbiter geometry at a hypersonic flight condition is presented. The Langley Aerothermodynamic Upwind Relaxation Algorithm (LAURA) code which incorporates a thermochemical nonequilibrium chemistry model, a finite rate catalytic wall boundary condition and wall temperature distribution based on radiation equilibrium is used in this study. In addition, the effect of choice of 'min mod' function, eigenvalue limiter and grid density on surface heating is investigated. The surface heating from a flowfield calculation at Mach number 22, altitude of 230,000 ft and 40 deg angle of attack is compared with flight data from three Orbiter flights.

Weilmuenster, K. J.↗
NASA NTRS1992

EMTP based stability analysis of space station electric power system in a test bed environment

The Space Station Freedom Electric Power System (EPS) will convert solar energy into electric energy and distribute the same using an 'all dc', Power Management and Distribution (PMAD) System. Power conditioning devices (dc to dc converters) are needed to interconnect parts of this system operating at different nominal voltage levels. Operation of such devices could generate under damped oscillations (instability) under certain conditions. Criteria for instability are examined and verified for a single device. Suggested extension of the criteria to a system operation is examined by using the EMTP model of the PMAD DC test bed. Wherever possible, data from the test bed is compared with the modeling results.

Dravid, Narayan V.↗
NASA NTRS1992

Late quaternary time series of Arabian Sea productivity: Global and regional signals

Modern annual floral and faunal production in the northwest Arabian Sea derives primarily from upwelling induced by strong southwest winds during June, July, and August. Indian Ocean summer monsoon winds are, in turn, driven by differential heating between the Asian continent and the Indian ocean to the south. This differential heating produces a strong pressure gradient resulting in southwest monsoon winds and both coastal and divergent upwelling off the Arabian Peninsula. Over geologic time scales (10(exp 4) to 10(exp 6) years), monsoon wind strength is sensitive to changes in boundary conditions which influence this pressure gradient. Important boundary conditions include the seasonal distribution of solar radiation, global ice volume, Indian Ocean sea surface temperature, and the elevation and albedo of the Asian continent. To the extent that these factors influence monsoon wind strength, they also influence upwelling and productivity. In addition, however, productivity associated with upwelling can be decoupled from the strength of the summer monsoon winds via ocean mechanisms which serve to inhibit or enhance the nutrient supply in the intermediate waters of the Indian Ocean, the source for upwelled waters in the Arabian Sea. To differentiate productivity associated with wind-induced upwelling from that associated with other components of the system such as nutrient sequestering in glacial-age deep waters, we employ a strategy which monitors independent components of the oceanic and atmospheric subsystems. Using sediment records from the Owen Ridge, northwest Arabian Sea, we monitor the strength of upwelling and productivity using two independent indicators, percent G. bulloides and opal accumulation. We monitor the strength of southwest monsoon winds by measuring the grain-size of lithogenic dust particles blown into the Arabian Sea from the surrounding deserts of the Somali and Arabian Peninsulas. Our current hypothesis is that the variability associated with the 41 kyr power in the G. bulloides and opal accumulation records derive from nutrient availability in the intermediate waters which are upwelled via monsoon winds. This hypothesis is testable by comparison with Cd records of intermediate and deep waters of the Atlantic and Indian Ocean.

Clemens, Steven C.↗
NASA NTRS1992

EMTP based stability analysis of Space Station Electric Power System in a test bed environment

The Space Station Freedom Electric Power System (EPS) will convert solar energy into electric energy and distribute the same using an 'all dc', Power Management and Distribution (PMAD) System. Power conditioning devices (dc to dc converters) are needed to interconnect parts of this system operating at different nominal voltage levels. Operation of such devices could generate under damped oscillations (instability) under certain conditions. Criteria for instability are examined and verified for a single device. Suggested extension of the criteria to a system operation is examined by using the EMTP model of the PMAD dc test bed. Wherever possible, data from the test bed is compared with the modeling results.

Dravid, Narayan V.↗
NASA NTRS1991

Sensitivity of acoustic predictions to variation of input parameters

The noise prediction code WOPWOP predicts the thickness and loading noise produced by a helicopter rotor, given the blade motion, rotor operating conditions, and fluctuating force distribution over the blade surface. However, the criticality of these various inputs, and their respective effects on the predicted acoustic field, have never been fully addressed. This paper examines the importance of these inputs, and the sensitivity of the acoustic predictions to a variation of each parameter. The effects of collective and cyclic pitch, as well as coning and flapping, are presented. Blade loading inputs are examined to determine the necessary spatial and temporal resolution, as well as the importance of the cordwise distribution. The acoustic predictions show regions in the acoustic field where significant errors occur when simplified blade motions or blade loadings are used. An assessment of the variation in the predicted acoustic field is balanced by a consideration of CPU time necessary for the various approximations.

Brentner, Kenneth S.↗
NASA NTRS1993

Relaxation of molecular velocities and spectral line profiles of astrophysical masers

The rates at which the velocities of water molecules relax to a Maxwellian distribution are calculated under conditions that are representative of those in astrophysical water masers. Populations are calculated as a function of velocity for the lowest 40 rotational energy levels of ortho-water in order to make a detailed determination of the velocity relaxation rate. Relaxation rates for the 22 GHz maser at H2 densities of 10 exp 9/cu cm are 2.0/s and 5.1/s for temperatures of 400 K and 1000 K, respectively. Under these and other conditions, as well as for other maser transitions, the relaxation rate far exceeds the loss rate - usually by more than a factor of 10. Thus maser lines can remain narrow up to intensities that are at least a factor of 10 greater than the saturation intensity, and to path lengths that are at least a factor of 10 greater than the path length at which saturation occurs. Relaxation is dominated by the effects of trapped infrared radiation, though elastic and inelastic collisions are also included in the calculations. These relaxation rates, together with the observed line breadths of the 22 GHz masers, provide limits on maser luminosities which indicate that the brightest 22 GHz masers are highly beamed, with solid angles smaller than 10 exp -5 to 10 exp -4 Sr.

Anderson, Nels↗
NASA NTRS1992

Supersonic/hypersonic aerodynamic methods for aircraft design and analysis

A methodology employed in engineering codes to predict aerodynamic characteristics over arbitrary supersonic/hypersonic configurations is considered. Engineering codes use a combination of simplified methods, based on geometrical impact angle and freestream conditions, to compute pressure distribution over the vehicle's surface in an efficient and timely manner. These approximate methods are valid for both hypersonic (Mach greater than 4) and lower speeds (Mach down to 2). It is concluded that the proposed methodology enables the user to obtain reasonable estimates of vehicle performance and engineering methods are valuable in the design process of these type of vehicles.

Torres, Abel O.↗