SEARCH · Engineering Papers

Results for “Code Analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

All sources NASA NTRS DOE OSTI

NASA NTRS1986

OSAC analysis of the Far Ultraviolet Spectroscopic Explorer (FUSE) telescope

An investigation is made of the sensitivity of the image quality for the proposed FUSE telescope to mirror misalignments and a wide spatial frequency range of figure errors. Representative figure error data was obtained for the analysis from measurements made on the SEUTS (Solar Extreme Ultraviolet Telescope Spectrograph) telescope mirrors. The tolerancing analysis was carried out with the aid of the Optical Surface Analysis Code (OSAC) program.

Saha, Timo T.↗

NASA NTRS1987

Winglets on low aspect ratio wings

The drag reduction potentially available from the use of winglets at the tips of low aspect ratio (1.75-2.67) wings with pronounced (45-60 deg) leading edge sweep is assessed numerically for the case of a cruise design point at Mach of 0.8 and a lift coefficient of 0.3. Both wing-winglet and wing-alone design geometries are derived from a linear-theory, minimum induced drag design methodology. Relative performance is evaluated with a nonlinear extended small disturbance potential flow analysis code. Predicted lift coefficient/pressure drag coefficient increases at equal lift for the wing-winglet configurations over the wing-alone planform are of the order of 14.6-15.8, when boundary layer interaction is included.

Kuhlman, John M.↗

NASA NTRS1984

An Experimental Evaluation of Advanced Rotorcraft Airfoils in the NASA Ames Eleven-foot Transonic Wind Tunnel

Five full scale rotorcraft airfoils were tested in the NASA Ames Eleven-Foot Transonic Wind Tunnel for full scale Reynolds numbers at Mach numbers from 0.3 to 1.07. The models, which spanned the tunnel from floor to ceiling, included two modern baseline airfoils, the SC1095 and SC1094 R8, which have been previously tested in other facilities. Three advanced transonic airfoils, designated the SSC-A09, SSC-A07, and SSC-B08, were tested to confirm predicted performance and provide confirmation of advanced airfoil design methods. The test showed that the eleven-foot tunnel is suited to two-dimensional airfoil testing. Maximum lift coefficients, drag coefficients, pitching moments, and pressure coefficient distributions are presented. The airfoil analysis codes agreed well with the data, with the Grumman GRUMFOIL code giving the best overall performance correlation.

Flemming, Robert J.↗

NASA NTRS1987

Impact of solids on composite materials

The failure modes of composite materials as a result of low velocity impact were investigated by simulating the impact with a finite element analysis. An important facet of the project is the modeling of the impact of a solid onto cylindrical shells composed of composite materials. The model under development will simulate the delamination sustained when a composite material encounters impact from another rigid body. The computer equipment was installed, the computer network tested, and a finite element method model was developed to compare results with known experimental data. The model simulated the impact of a steel rod onto a rotating shaft. Pre-processing programs (GMESH and TANVEL) were developed to generate node and element data for the input into the three dimensional, dynamic finite element analysis code (DYNA3D). The finite element mesh was configured with a fine mesh near the impact zone and a coarser mesh for the impacting rod and the regions surrounding the impacting zone. For the computer simulation, five impacting loads were used to determine the time history of the stresses, the scribed surface areas, and the amount of ridging. The processing time of the computer codes amounted from 1 to 4 days. The calculated surface area were within 6-12 percent, relative error when compated to the actual scratch area.

Bronson, Arturo↗

NASA NTRS1988

Integrated multidisciplinary analysis tool IMAT users' guide

The Integrated Multidisciplinary Analysis Tool (IMAT) is a computer software system developed at Langley Research Center. IMAT provides researchers and analysts with an efficient capability to analyze satellite controls systems influenced by structural dynamics. Using a menu-driven executive system, IMAT leads the user through the program options. IMAT links a relational database manager to commercial and in-house structural and controls analysis codes. This paper describes the IMAT software system and how to use it.

Meissner, Frances T.↗

NASA NTRS1988

The Environment for Application Software Integration and Execution (EASIE) version 1.0. Volume 4: System installation and maintenance guide

The Environment for Application Software Integration and Execution (EASIE) provides both a methodology and a set of software utility programs to ease the task of coordinating engineering design and analysis codes. This document provides necessary information for installing the EASIE software on a host computer system. The target host is a DEX VAX running VMS version 4; host dependencies are noted when appropriate. Relevant directories and individual files are identified, and compile/load/execute sequences are specified. In the case of the data management utilities, database management system (DBMS) specific features are described in an effort to assist the maintenance programmer in converting to a new DBMS. The document also describes a sample EASIE program directory structure to guide the program implementer in establishing his/her application dependent environment.

Randall, Donald P.↗

NASA NTRS1989

A Transversely Isotropic Thermoelastic Theory

A continuum theory is presented for representing the thermoelastic behavior of composites that can be idealized as transversely isotropic. This theory is consistent with anisotropic viscoplastic theories being developed presently at NASA Lewis Research Center. A multiaxial statement of the theory is presented, as well as plane stress and plane strain reductions. Experimental determination of the required material parameters and their theoretical constraints are discussed. Simple homogeneously stressed elements are examined to illustrate the effect of fiber orientation on the resulting strain distribution. Finally, the multiaxial stress-strain relations are expressed in matrix form to simplify and accelerate implementation of the theory into structural analysis codes.

Arnold, S. M.↗

NASA NTRS1987

Design of transonic airfoils and wings using a hybrid design algorithm

A method has been developed for designing airfoils and wings at transonic speeds. It utilizes a hybrid design algorithm in an iterative predictor/corrector approach, alternating between analysis code and a design module. This method has been successfully applied to a variety of airfoil and wing design problems, including both transport and highly-swept fighter wing configurations. An efficient approach to viscous airfoild design and the effect of including static aeroelastic deflections in the wing design process are also illustrated.

Campbell, Richard L.↗

NASA NTRS1988

Design of low Reynolds number airfoils. I

The low Reynolds number airfoils designated ASM-LRN-003 and -007 have been designed for high section L/D ratios using Drela's (1985) design-and-analysis code; close to 70-percent laminar flow is maintained on the upper surfaces, and 100-percent on the lower, at coefficients of lift of 1.0-1.3, assuming optimum laminar separation and transition control on the upper surface by means of suitable turbulators. If peak performance is critical, airfoils of this type with an undercut front lower surface and a correspondingly sharper leading edge may be resorted to.

Pfenninger, W.↗

NASA NTRS1988

Integration of rocket turbine design and analysis through computer graphics

An interactive approach with engineering computer graphics is used to integrate the design and analysis processes of a rocket engine turbine into a progressive and iterative design procedure. The processes are interconnected through pre- and postprocessors. The graphics are used to generate the blade profiles, their stacking, finite element generation, and analysis presentation through color graphics. Steps of the design process discussed include pitch-line design, axisymmetric hub-to-tip meridional design, and quasi-three-dimensional analysis. The viscous two- and three-dimensional analysis codes are executed after acceptable designs are achieved and estimates of initial losses are confirmed.

Hsu, Wayne↗

NASA NTRS1988

Two-dimensional aerodynamic characteristics of the OLS/TAAT airfoil

Two flight tests have been conducted that obtained extension pressure data on a modified AH-1G rotor system. These two tests, the Operational Loads Survey (OLS) and the Tip Aerodynamics and Acoustics Test (TAAT) used the same rotor set. In the analysis of these data bases, accurate 2-D airfoil data is invaluable, for not only does it allow comparison studies between 2- and 3-D flow, but also provides accurate tables of the airfoil characteristics for use in comprehensive rotorcraft analysis codes. To provide this 2-D data base, a model of the OLS/TAAT airfoil was tested over a Reynolds number range from 3 x 10 to the 6th to 7 x 10 to the 7th and between Mach numbers of 0.34 to 0.88 in the NASA Langley Research Center's 6- by 28-Inch Transonic Tunnel. The 2-D airfoil data is presented as chordwise pressure coefficient plots, as well as lift, drag, and pitching moment coefficient plots and tables.

Watts, Michael E.↗

NASA NTRS1989

Plotting component maps in the Navy/NASA Engine Program (NNEP): A method and its usage

The Navy/NASA Engine Program (NNEP) and the new extended version which handles chemical equilibrium (NNEPEQ) are very general cycle analysis codes that have been used extensively to calculate design and off-design performance of a wide range of turbine engine cycles and configurations. Component maps are used to obtain the off-design engine performance and a matched engine cycle. This paper describes a method of plotting the scaled NNEP compressor and turbine maps as the user runs the NNEP code as well as plotting the operating line defined by all the cases that were computed in that particular NNEP run. Afterwards, an example demonstrates the use of this capability to help analyze an engine cycle model and then make improvements to that cycle.

Plencner, Robert M.↗

NASA NTRS1988

IMAT (Integrated Multidisciplinary Analysis Tool) user's guide for the VAX/VMS computer

The Integrated Multidisciplinary Analysis Tool (IMAT) is a computer software system for the VAX/VMS computer developed at the Langley Research Center. IMAT provides researchers and analysts with an efficient capability to analyze satellite control systems influenced by structural dynamics. Using a menu-driven executive system, IMAT leads the user through the program options. IMAT links a relational database manager to commercial and in-house structural and controls analysis codes. This paper describes the IMAT software system and how to use it.

Meissner, Frances T.↗

NASA NTRS1988

Supersonic throughflow fans

Supersonic throughflow fan research, and technology needs are reviewed. The design of a supersonic throughflow fan stage, a facility inlet, and a downstream diffuser is described. The results from the analysis codes used in executing the design are shown. An engine concept intended to permit establishing supersonic throughflow within the fan on the runway and maintaining the supersonic throughflow condition within the fan throughout the flight envelope is presented.

Ball, C. L.↗

NASA NTRS1987

Mechanics of materials model

The Mechanics of Materials Model (MOMM) is a three-dimensional inelastic structural analysis code for use as an early design stage tool for hot section components. MOMM is a stiffness method finite element code that uses a network of beams to characterize component behavior. The MOMM contains three material models to account for inelastic material behavior. These include the simplified material model, which assumes a bilinear stress-strain response; the state-of-the-art model, which utilizes the classical elastic-plastic-creep strain decomposition; and Walker's viscoplastic model, which accounts for the interaction between creep and plasticity that occurs under cyclic loading conditions.

Meister, Jeffrey P.↗

NASA NTRS1987

Finite element implementation of viscoplastic models

A brief description of the implementation in MARK, the general purpose finite element structural analysis code, of two viscoplastic models developed by Robinson is given. One model is for isotropic materials and the other is for metal matrix composites. Also presented are analytical results obtained for hot section components using these models.

Arya, V. K.↗

NASA NTRS1989

Generic element processor (application to nonlinear analysis)

The focus here is on one aspect of the Computational Structural Mechanics (CSM) Testbed: finite element technology. The approach involves a Generic Element Processor: a command-driven, database-oriented software shell that facilitates introduction of new elements into the testbed. This shell features an element-independent corotational capability that upgrades linear elements to geometrically nonlinear analysis, and corrects the rigid-body errors that plague many contemporary plate and shell elements. Specific elements that have been implemented in the Testbed via this mechanism include the Assumed Natural-Coordinate Strain (ANS) shell elements, developed with Professor K. C. Park (University of Colorado, Boulder), a new class of curved hybrid shell elements, developed by Dr. David Kang of LPARL (formerly a student of Professor T. Pian), other shell and solid hybrid elements developed by NASA personnel, and recently a repackaged version of the workhorse shell element used in the traditional STAGS nonlinear shell analysis code. The presentation covers: (1) user and developer interfaces to the generic element processor, (2) an explanation of the built-in corotational option, (3) a description of some of the shell-elements currently implemented, and (4) application to sample nonlinear shell postbuckling problems.

Stanley, Gary↗

NASA NTRS1989

SINFAC simulation of a high-power hybrid CPL

The systems improved numerical fluids analysis code (SINFAC) was used to model a high-power hybrid capillary-pumped loop. A comparison was made between the simulation results and actual experimental test data for the mechanical-pump-assist mode of operation. The hybrid capillary-pumped loop consisted of a capillary-pumped loop with a mechanical pump in the liquid return line with a bypass value so that the system could be operated either as a capillary-only loop or a series hybrid loop. Excellent agreement was obtained between numerical and experimental data.

Benner, Steve M.↗