Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “BYPASSES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

Measurements and Predictions of the Noise from Three-Stream Jets

An experimental and numerical investigation of the noise produced by high-subsonic and supersonic three-stream jets was conducted. The exhaust system consisted of externally-mixed-convergent nozzles and an external plug. Bypass- and tertiary-to-core area ratios between 1.0 and 2.5, and 0.4 and 1.0, respectively, were studied. Axisymmetric and offset tertiary nozzles were investigated for heated and unheated conditions. For axisymmetric configurations, the addition of the third stream was found to reduce peak- and high-frequency acoustic levels in the peak-jet-noise direction, with greater reductions at the lower bypass-to-core area ratios. For the offset configurations, an offset duct was found to decrease acoustic levels on the thick side of the tertiary nozzle relative to those produced by the simulated two-stream jet with up to 8 dB mid-frequency noise reduction at large angles to the jet inlet axis. Noise reduction in the peak-jet-noise direction was greater for supersonic core speeds than for subsonic core speeds. The addition of a tertiary nozzle insert used to divert the third-stream jet to one side of the nozzle system provided no noise reduction. Noise predictions are presented for selected cases using a method based on an acoustic analogy with mean flow interaction effects accounted for using a Green's function, computed in terms of its coupled azimuthal modes for the offset cases, and a source model previously used for round and rectangular jets. Comparisons of the prediction results with data show that the noise model predicts the observed increase in low-frequency noise with the introduction of a third, axisymmetric stream, but not the high-frequency reduction. For an offset third stream, the model predicts the observed trend of decreased sound levels on the thick side of the jet compared with the thin side, but the predicted azimuthal variations are much less than those seen in the data. Also, the shift of the spectral peak to lower frequencies with increasing polar angle is over-predicted. For an offset third stream with a heated core, it is shown that including the enthalpy-flux source terms in the acoustic analogy model improves predictions compared with those obtained using only the momentum flux.

Three-Stream Jets↗

Measurements and Predictions of the Noise from Three-Stream Jets

An experimental and numerical investigation of the noise produced by high-subsonic and supersonic three-stream jets was conducted. The exhaust system consisted of externally-mixed-convergent nozzles and an external plug. Bypass- and tertiary- to-core area ratios between 1.0 and 2.5, and 0.4 and 1.0, respectively, were studied. Axisymmetric and offset tertiary nozzles were investigated for heated and unheated conditions. For axisymmetric configurations, the addition of the third stream was found to reduce peak- and high-frequency acoustic levels in the peak-jet-noise direction, with greater reductions at the lower bypass-to-core area ratios. For the offset configurations, an offset duct was found to decrease acoustic levels on the thick side of the tertiary nozzle relative to those produced by the simulated two-stream jet with up to 8 dB mid-frequency noise reduction at large angles to the jet inlet axis. Noise reduction in the peak-jet-noise direction was greater for supersonic core speeds than for subsonic core speeds. The addition of a tertiary nozzle insert used to divert the third-stream jet to one side of the nozzle system provided no noise reduction. Noise predictions are presented for selected cases using a method based on an acoustic analogy with mean flow interaction effects accounted for using a Green's function, computed in terms of its coupled azimuthal modes for the offset cases, and a source model previously used for round and rectangular jets. Comparisons of the prediction results with data show that the noise model predicts the observed increase in low-frequency noise with the introduction of a third, axisymmetric stream, but not the high-frequency reduction. For an offset third stream, the model predicts the observed trend of decreased sound levels on the thick side of the jet compared with the thin side, but the predicted azimuthal variations are much less than those seen in the data. Also, the shift of the spectral peak to lower frequencies with increasing polar angle is over-predicted. For an offset third stream with a heated core, it is shown that including the enthalpy-flux source terms in the acoustic analogy model improves predictions compared with those obtained using only the momentum- flux.

Three-Stream Jets↗

Flow Diode and Method for Controlling Fluid Flow Origin of the Invention

A flow diode configured to permit fluid flow in a first direction while preventing fluid flow in a second direction opposite the first direction is disclosed. The flow diode prevents fluid flow without use of mechanical closures or moving parts. The flow diode utilizes a bypass flowline whereby all fluid flow in the second direction moves into the bypass flowline having a plurality of tortuous portions providing high fluidic resistance. The portions decrease in diameter such that debris in the fluid is trapped. As fluid only travels in one direction through the portions, the debris remains trapped in the portions.

Dyson, Rodger W↗

High Altitude Small Engine Test Techniques at the NASA Glenn Propulsion Systems Lab

A High Altitude Test was performed in the Propulsion Systems Lab (PSL) at the NASA Glenn Research Center using a Pratt and Whitney Canada PW545 jet engine. This engine was tested to develop a highaltitude database on small, high-bypass ratio, engine performance and operability. Industry is interested in the use of high-bypass engines for Uninhabited Aerial Vehicles (UAV's) to perform high altitude surveillance. The tests were a combined effort between Pratt & Whitney Canada (PWC) and NASA Glenn Research Center. A large portion of this test activity was to collect performance data with a highly instrumented low-pressure turbine. Low-pressure turbine aerodynamic performance at low Reynolds numbers was collected and compared to analytical models developed by NASA and PWC. This report describes the test techniques implemented to obtain high accuracy turbine performance data in an altitude test facility, including high accuracy airflow at high altitudes, very low mass flow, and low air temperatures. Major accomplishments from this test activity were to collect accurate and repeatable turbine performance data at high altitudes to within 1 percent. Data were collected at 19,800m, 16,750m, and 13,700m providing documentation of diminishing LPT performance with reductions in Reynolds number in an actual engine flight environment. The test provided a unique database for the development of engine analysis codes to be used for future LPT performance improvements.

Castner, Raymond↗

By-Pass Diode Temperature Tests of a Solar Array Coupon Under Space Thermal Environment Conditions

Tests were performed on a 56-cell Advanced Triple Junction solar array coupon whose purpose was to determine margin available for bypass diodes integrated with new, large multi-junction solar cells that are manufactured from a 4-inch wafer. The tests were performed under high vacuum with cold and ambient coupon back-side. The bypass diodes were subjected to a sequence of increasing discrete current steps from 0 Amp to 2.0 Amp in steps of 0.25 Amp. At each current step, a temperature measurement was obtained via remote viewing by an infrared camera. This paper discusses the experimental methodology, including the calibration of the thermal imaging system, and the results.

Wright, Kenneth H., Jr.↗

Numerical and Analytical Assessment of a Coupled Rotating Detonation Engine and Turbine Experiment

An analysis is presented of an experimental rig comprising a rotating detonation engine (RDE) with bypass ejector flow coupled to a downstream turbine. The analysis used a validated computational fluid dynamics RDE simulation combined with straightforward algebraic mixing equations for the bypass flow. The objectives of the analysis were to supplement and interpret the necessarily sparse measurements from the rig, and to assess the performance of the RDE itself, which was not instrumented in this installation. The analysis is seen to agree reasonably well with available data. It shows that the RDE is operating in an unusual fashion, with subsonic flow throughout the exhaust plane. The detonation event itself is producing a total pressure rise relative to the pre-detonative pressure; however, the length of the device and the substantial flow restriction at the inlet yield an overall pressure loss. This is not surprising since the objective of the rig test was primarily aimed at investigating RDE/turbine interactions, and not on performance optimization. Furthermore, the RDE was designed for fundamental detonation studies and not performance. Nevertheless, the analysis indicates that with some small alterations to the design, an RDE with an overall pressure rise is possible.

detonation↗

Numerical and Analytical Assessment of a Coupled Rotating Detonation Engine and Turbine Experiment

An analysis is presented of an experimental rig comprising a rotating detonation engine (RDE) with bypass ejector flow coupled to a downstream turbine. The analysis used a validated computational fluid dynamics RDE simulation combined with straightforward algebraic mixing equations for the bypass flow. The objectives of the analysis were to supplement and interpret the necessarily sparse measurements from the rig, and to assess the performance of the RDE itself, which was not instrumented in this installation. The analysis is seen to agree reasonably well with available data. It shows that the RDE is operating in an unusual fashion, with subsonic flow throughout the exhaust plane. The detonation event itself is producing a total pressure rise relative to the pre-detonative pressure; however, the length of the device and the substantial flow restriction at the inlet yield an overall pressure loss. This is not surprising since the objective of the rig test was primarily aimed at investigating RDE turbine interactions, and not on performance optimization. Furthermore, the RDE was designed for fundamental detonation studies and not performance. Nevertheless, the analysis indicates that with some small alterations to the design, an RDE with an overall pressure rise is possible.

propulsion↗

Numerical and Analytical Assessment of a Coupled Rotating Detonation Engine and Turbine Experiment

An analysis is presented of an experimental rig comprising a rotating detonation engine (RDE) with bypass flow coupled to a downstream turbine. The analysis used a validated computational fluid dynamics RDE simulation combined with straightforward algebraic mixing equations for the bypass flow. The objectives of the analysis were to supplement and interpret the necessarily sparse measurements from the rig, and to assess the performance of the RDE itself (which was not instrumented in this installation). The analysis is seen to agree reasonably well with available data. It shows that the RDE is operating in an unusual fashion, with subsonic flow throughout the exhaust plane. The detonation event itself is producing a total pressure rise relative to the pre-detonative pressure; however, the length of the device and the substantial flow restriction at the inlet yield an overall pressure loss. This is not surprising since the objective of the rig test was primarily aimed at investigating RDEturbine interactions, and not on performance optimization. Furthermore, the RDE was designed for fundamental detonation studies and not performance. Nevertheless, the analysis indicates that with some small alterations to the design, an RDE with an overall pressure rise is possible.

detonation↗

Efficient, Low Pressure Ratio Propulsor for Gas Turbine Engines

A gas turbine engine includes a core flow passage, a bypass flow passage, and a propulsor arranged at an inlet of the bypass flow passage and the core flow passage. The propulsor includes a row of propulsor blades. The row includes no more than 20 of the propulsor blades. The propulsor has a pressure ratio between about 1.2 and about 1.7 across the propulsor blades.

Gallagher, Edward J.↗

Assessment of Mixer-Ejector Nozzle with Thermal Acoustic Shield for Jet Noise Reduction

A tendency for excessive exhaust jet mixing noise from low bypass ratio turbofan engines is recognized as a key challenge in the design of commercial supersonic aircraft. In this work we investigate a unique combination of two noise mitigation methods as a novel strategy to reduce jet mixing noise. First, a thermal acoustic shield (TAS) is used to reflect high frequency acoustic waves at small angles to the jet axis; second, a mixer-ejector (ME) nozzle is used to mechanically shield noise propagating at large angles to the axis. The ME shroud also provides a convenient location for a TAS nozzle and improves TAS effectiveness by limiting the downstream extent of high frequency noise generation. In an additional benefit for a velocity-matched TAS stream, the ME allows a reduction in strength of the TAS outer shear layer which could serve as a secondary noise source. The present work provides a quantitative assessment of the ME-TAS concept, using a combination of RANS CFD simulations, acoustic analogy calculations for the farfield Green's function, and surrogate-based modeling and parameter space exploration. We first evaluate a subscale configuration, then use scaling arguments to apply subscale results to the systems-level analysis of a flight configuration; the latter configuration includes a generic low bypass ratio turbofan engine with an engine-driven electric generator for supplementary heating of the TAS stream. Additional RANS CFD calculations are performed for a notional ME-TAS geometry based on the full scale configuration, and various modeling assumptions and operational characteristics are evaluated. The ME-TAS concept is shown to provide effective shielding for high frequency jet noise, and should enable comparable noise suppression to a stand-alone ME of considerably greater length, weight and drag. In addition to investigating the integrated ME-TAS system, the present work differs from previous research into TAS and related fluidic shield concepts through the inclusion of modern numerical analysis tools and the systematic numerical examination of various design parameters.

thermal acoustic shield↗

Preliminary Study of Heat Pipe Turbine Vane Cooling in the NASA N+3 Reference Engine

This paper investigates the effects of implementing Heat Pipe Turbine Vane (HPTV) cooling in the NASA N+3 engine. The HPTV can be thought of as a heat pipe in the shape of a turbine vane, functioning as both an aerodynamic body and heat exchanger. The heat-absorbing section of the HPTV remains fixed in the vanes of the high pressure turbine (HPT), while the heat-rejecting section can be placed in any stage of the low pressure turbine (LPT) as well as the bypass stream. The optimal location of the condensing (heat-rejecting) section is shown to be in the bypass stream for both HPT stages. The thrust specific fuel consumption increased by 0.2%, which is mainly attributed to the elimination of air cooling in the second stage HPT vanes combined with the transfer of energy from the main gas path to elsewhere in the cycle. Air cooling is also eliminated in the first stage HPT vanes, but this cooling air is nonchargeable. A preliminary design is proposed and shown to demonstrate the desired performance and operates below all the heat flux limitations in the first stage HPT . The design in the second stage HPT exceeds a limiting phenomenon but is expected to be remedied by changing the working fluid.

Gas Turbine↗

An embedded planar-foil capacitor material, FPGA based interposer, aimed at improving system performance and reduced board size for space based electronics

This paper presents work to date in developing, and testing an embedded planar-foil capacitor based interposer intended to be integrated together with high-density components such as Field Programmable Gate Arrays (FPGAs), and Application Specific Integrated Circuits (ASIC). FPGA devices typically have a large number of I/O and power pins. The high speed enabled by these devices requires a large number of discrete bypass capacitors as close as possible to the power pins. These capacitors take up a considerable amount of the board area on the application circuit board. The developed interposer replaces these components freeing up space of traditional bypass capacitors for other circuitry.

Cheng, Ben↗

Preliminary Study of Heat Pipe Turbine Vane Cooling in the NASA N+3 Reference Engine

This investigates the effects of implementing Heat Pipe Turbine Vane (HPTV) cooling in the NASA N+3 engine. The HPTV can be thought of as a heat pipe in the shape of a turbine vane, functioning as both an aerodynamic body and heat exchanger. The heat-absorbing section of the HPTV remains fixed in the vanes of the high pressure turbine (HPT), while the heat-rejecting section can be placed in any stage of the low pressure turbine (LPT) as well as the bypass stream. The optimal location of the condensing (heat-rejecting) section is shown to be in the bypass stream for both HPT stages. The thrust specific fuel consumption increased by 0.2%, which is mainly attributed to the elimination of air cooling in the second stage HPT vanes combined with the transfer of energy from the main gas path to elsewhere in the cycle. Air cooling is also eliminated in the first stage HPT vanes, but this cooling air is nonchargeable. A preliminary design is proposed and shown to demonstrate the desired performance and operates below all the heat flux limitations in the first stage HPT . The design in the second stage HPT exceeds a limiting phenomenon but is expected to be remedied by changing the working fluid.

Gas Turbine↗

Conceptual Design of Propulsors for the SUSAN Electrofan Transport Aircraft

Conceptual designs of the propulsor modules for the SUSAN electro-fan aircraft are sought after. Shaft power requirement is reduced by using boundary layer ingesting propulsion technology. There are several obstacles to designing feasible BLI propulsion systems such as inlet distortion, flow blockage from ingesting low-momentum flow, strong coupling between airframe and propulsion systems. Thus, the high fidelity CFD tool is indispensable to assess the performance of the propulsion systems and evaluate the inlet profiles during the design process. Consequently, the CFD data is used to update the inputs for the NPSS model from the initial stage of the system design. Hence, the inlet sizing, fan design, and estimation of the power saving are carried out. Various installation concepts of the mail-slot nacelle, such as under-/over-wing and trailing edge configurations, are investigated for the wing-mounted turbo-electric distributed propulsor module, and their power-saving is evaluated. As for the tail-mounted turbofan engine, the fan diameter and inlet captured area is determined based on the CFD profiles. An appropriate area ratio of the bypass and core ducts is derived from meeting the target bypass ratio from the system design. The baseline fan stage is analyzed by full annulus URANS CFD to assess the efficiency penalty due to the ingested pressure and swirl distortions.

SUSAN Electro-Fan Aircraft↗

Conceptual Design of Propulsors for the SUSAN Electrofan Transport Aircrafts

Conceptual designs of the propulsor modules for the SUSAN electro-fan aircraft are sought after. Shaft power requirement is reduced by using boundary layer ingesting propulsion technology. There are several obstacles to designing feasible BLI propulsion systems such as inlet distortion, flow blockage from ingesting low-momentum flow, strong coupling between airframe and propulsion systems. Thus, the high fidelity CFD tool is indispensable to assess the performance of the propulsion systems and evaluate the inlet profiles during the design process. Consequently, the CFD data is used to update the inputs for the NPSS model from the initial stage of the system design. Hence, the inlet sizing, fan design, and estimation of the power saving are carried out. Various installation concepts of the mail-slot nacelle, such as under-/over-wing and trailing edge configurations, are investigated for the wing-mounted turbo-electric distributed propulsor module, and their power-saving is evaluated. As for the tail-mounted turbofan engine, the fan diameter and inlet captured area is determined based on the CFD profiles. An appropriate area ratio of the bypass and core ducts is derived from meeting the target bypass ratio from the system design. The baseline fan stage is analyzed by full annulus URANS CFD to assess the efficiency penalty due to the ingested pressure and swirl distortions.

Electric Aircraft↗

An Embedded Planar-Foil Capacitor Material, FPGA Based Interposer, Aimed at Improving System Performance and Reduced Board Size for Space Based Electronics

This paper presents our work to date in developing, and testing an embedded planar-foil capacitor based interposer intended to be integrated together with high-density components such as Field Programmable Gate Arrays (FPGAs), and Application Specific Integrated Circuit (ASIC) applications. FPGA devices typically have a large number of I/O and power pins. The high speed enabled by these devices requires a large number of discrete bypass capacitors as close as possible to the power pins. These capacitors take up a considerable amount of the board area on the application circuit board. Our interposer replaces these components freeing up space of traditional bypass capacitors for other circuitry. Our Interposer focuses on the needs of Micro Semi’s RTG4 FPGA. We developed the interposer using COTS embedded foil capacitors. The Interposer is customized to the capacitance requirements for each of the FPGA banks. We evaluated three foil manufactures Oak Mitsui, 3M and TDK. The three different designs were evaluated, but we will focus on the Oak-Mitsui based Interposer that we constructed and tested. Through simulations, we validate the horizontal and vertical interconnect inductances, that FPGA decoupling requirements are met. The use of the interposer results in an overall reduction in our Printed Wiring Board (PWB) area.

Hunter, Don J↗

Diagnosing Noise Features Of Internally Mixed, External Plug Exhaust Systems

In internally mixed exhaust systems, a lobed or forced mixer is employed to mix the core and bypass streams before they exit the common nozzle. For moderate bypass-ratio engines this marginally improves thrust, and provides a significant acoustic benefit. Indeed, it has been thought that a fully mixed jet creates the lowest noise you can get from a two-stream engine. Typically, the forced mixer system produces a bit more noise than a fully mixed equivalent jet, noise that has been called “excess noise”. In recent testing, this excess noise seemed to be amplified when an external plug was employed in the exhaust system to reduce boattail drag. Identifying the mechanism of this excess noise and mitigating it is key to creating commercial supersonic vehicles that are acoustically acceptable around airports. This paper adds to that investigation, analyzing results from recent tests where far-field acoustic data were acquired on two sets of flows with matched fully mixed flow conditions. One set of flows had a heated core stream, making it a dual-stream jet. The other set had both streams heated to the same temperature, making a single-stream jet that matched the fully mixed temperature and velocity of the dual-stream jet. These flows were tested in two lobed-mixer exhaust systems with internal and external plugs. Analysis of flow and noise data from the nozzles with combinations of single- and dual-stream flows, and with and without flight streams, gives insight into how and why the noise of the dual-stream and single-stream jet differ. One additive source, present in nozzles both with and without external plugs, comes from inside the nozzle, likely the internal shear layer coming off the lobed mixer. This noise source is not impacted by a change in flight stream and has a distinctive spectral directivity that is amplified by the presence of the external plug. Finding the exact source mechanism of this new source will be key to making the internally mixed exhaust systems reach their lowest possible sound level.

Noise prediction, supersonic, jet noise↗

Diagnosing Noise Features Of Internally Mixed, External Plug Exhaust Systems

In internally mixed exhaust systems, a lobed or forced mixer is employed to mix the core and bypass streams before they exit the common nozzle. For moderate bypass-ratio engines this marginally improves thrust, and provides a significant acoustic benefit. Indeed, it has been thought that a fully mixed jet creates the lowest noise you can get from a two-stream engine. Typically, the forced mixer system produces a bit more noise than a fully mixed equivalent jet, noise that has been called “excess noise”. In recent testing, this excess noise seemed to be amplified when an external plug was employed in the exhaust system to reduce boattail drag. Identifying the mechanism of this excess noise and mitigating it is key to creating commercial supersonic vehicles that are acoustically acceptable around airports. This paper adds to that investigation, analyzing results from recent tests where far-field acoustic data were acquired on two sets of flows with matched fully mixed flow conditions. One set of flows had a heated core stream, making it a dual-stream jet. The other set had both streams heated to the same temperature, making a single-stream jet that matched the fully mixed temperature and velocity of the dual-stream jet. These flows were tested in two lobed-mixer exhaust systems with internal and external plugs. Analysis of flow and noise data from the nozzles with combinations of single- and dual-stream flows, and with and without flight streams, gives insight into how and why the noise of the dual-stream and single-stream jet differ. One additive source, present in nozzles both with and without external plugs, comes from inside the nozzle, likely the internal shear layer coming off the lobed mixer. This noise source is not impacted by a change in flight stream and has a distinctive spectral directivity that is amplified by the presence of the external plug. Finding the exact source mechanism of this new source will be key to making the internally mixed exhaust systems reach their lowest possible sound level.

Noise prediction↗