Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Additively Manufacturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
NASA NTRS2015

EBF3 Design and Sustainability Considerations

Electron beam freeform fabrication (EBF3) is a cross-cutting technology for producing structural metal parts using an electron beam and wire feed in a layer-additive fashion. This process was developed by researchers at NASA Langley to specifically address needs for aerospace applications. Additive manufacturing technologies like EBF3 enable efficient design of materials and structures by tailoring microstructures and chemistries at the local level to improve performance at the global level. Additive manufacturing also facilitates design freedom by integrating assemblies into complex single-piece components, eliminating flanges, fasteners and joints, resulting in reduced size and mass. These same efficiencies that permit new design paradigms also lend themselves to supportability and sustainability. Long duration space missions will require a high degree of self-sustainability. EBF3 is a candidate technology being developed to allow astronauts to conduct repairs and fabricate new components and tools on demand, with efficient use of feedstock materials and energy.

Taminger, Karen M. B.↗
NASA NTRSDate not supplied

Tesla Valve Integration into Propulsion Systems for Water Hammer Mitigation

Water hammer is a pressure surge or wave caused when a liquid in motion is forced to stop or change direction suddenly. Satellite and in-space propulsion systems exhibit this effect when valves, which can pulse several times per second, close quickly to isolate propellant from thrusters. The inherent nature of pulsing thrusters quickly has made water hammer a constant design challenge for these systems. Historically, the standard is to accept that the Maximum Design Pressure (MDP) of the system must account for a full worst case water-hammer event, which can be several times the Maximum Expected Operating Pressure (MEOP). An investigation is being conducted to determine the effectiveness of tesla valves in reducing water hammer amplitudes. Tesla Valves can be used in-line within propulsion systems to allow unrestricted flow in one direction and restricted flow in the opposite direction without the use of added mechanical or electrical components. Tesla valves use fixed internal geometry to allow for this unrestricted and restricted flow. With the increase and capability of Additive Manufacturing (AM), different configurations and concepts of tesla valves can be manufactured and tested at minimal cost. This concept could possibly be used to allow for a less complicated, or robust satellite and in-space propulsion system. This presentation will cover topics of additive manufactured design of tesla valves, testing, and variables to consider within tesla valve creation.

Michael A Willis↗
NASA NTRSDate not supplied

Power and Propulsion: Small Core Advanced Thermal Management Project Overview

This presentation is intended to provide an overview of the various efforts under the Advanced Air Transport Technology (AATT) project related to engine thermal management. Sustainable flight is the key motivator for all our efforts, and innovative thermal technologies play a crucial role in achieving this goal. The technologies described in this presentation can be applied to both traditional gas turbines and advanced cycles which utilize alternative fuels. Within our project, we utilize the capabilities of artificial intelligence (AI), machine learning (ML), and additive manufacturing. This ranges from using AI to generate heat exchanger fin topologies, to using ML for a reduction in computational cost which allows for a more thorough design exploration. Many times, the resulting topologies can only be realized through additive manufacturing techniques. Most of what’s presented is currently low TRL, but the intent is to achieve TRL 4 by the end of the project.

Propulsion↗
NASA NTRS2020

Producing Next Generation Superalloys Through Advanced Characterization and Manufacturing Techniques

NASA is currently working towards developing the next generation high temperature alloys for various aerospace and energy applications. Through advanced microscopy and computational insights, a novel atomic scale strengthening mechanism was discovered in Ni-base superalloys. This new local phase transformation strengthening technique has been successfully implemented resulting in new disk alloys with substantial improvements in creep strength over current state-of-the-art. Furthermore, additive manufacturing has been leveraged to produce dispersion strengthened (DS), multi-principal element alloys (MPEA) without the use of traditional mechanical alloying or chemical reactions. This new processing technique has successfully resulted in 99.9% dense oxide dispersion strengthened NiCoCr alloy parts. High temperature mechanical testing of the DS alloys showed significant improvements in strength and ductility over the baseline NiCoCr. As a result, this recently discovered processing route opens a new alloy design and production path that is synergistic between additive manufacturing and dispersion strengthening, possibly enabling a new generation of high-performance alloys.

Smith, Timothy M.↗
NASA NTRS2014

Investigation into the Use of the Concept Laser QM System as an In-Situ Research and Evaluation Tool

The NASA Marshall Space Flight Center (MSFC) is using a Concept Laser Fusing (Cusing) M2 powder bed additive manufacturing system for the build of space flight prototypes and hardware. NASA MSFC is collecting and analyzing data from the M2 QM Meltpool and QM Coating systems for builds. This data is intended to aide in understanding of the powder-bed additive manufacturing process, and in the development of a thermal model for the process. The QM systems are marketed by Concept Laser GmbH as in-situ quality management modules. The QM Meltpool system uses both a high-speed near-IR camera and a photodiode to monitor the melt pool generated by the laser. The software determines from the camera images the size of the melt pool. The camera also measures the integrated intensity of the IR radiation, and the photodiode gives an intensity value based on the brightness of the melt pool. The QM coating system uses a high resolution optical camera to image the surface after each layer has been formed. The objective of this investigation was to determine the adequacy of the QM Meltpool system as a research instrument for in-situ measurement of melt pool size and temperature and its applicability to NASA's objectives in (1) Developing a process thermal model and (2) Quantifying feedback measurements with the intent of meeting quality requirements or specifications. Note that Concept Laser markets the system only as capable of giving an indication of changes between builds, not as an in-situ research and evaluation tool. A secondary objective of the investigation is to determine the adequacy of the QM Coating system as an in-situ layer-wise geometry and layer quality evaluation tool.

Bagg, Stacey↗
NASA NTRS2018

Enhanced Liquid Oxygen-Propylene Rocket Engine

Provided herein are various improvements to rocket engine components and rocket engine operational techniques. In one example, a rocket engine propellant injection apparatus is provided that includes a manifold formed into a single body by an additive manufacturing process and comprising a fuel cavity and an oxidizer cavity. The manifold also includes one or more propellant feed stubs, the one or more propellant feed stubs protruding from the manifold and formed into the single body of the manifold by the additive manufacturing process, with at least a first stub configured to carry fuel to the fuel cavity and at least a second stub configured to carry oxidizer to the oxidizer cavity. The manifold also includes a plurality of injection features formed by apertures in a face of the manifold, ones of the plurality of injection features configured to inject the fuel and the oxidizer for combustion.

Bostwick, Christopher↗
NASA NTRS2018

Characterization of Titanium Alloys Produced by Electron Beam Directed Energy Deposition

Functionally graded materials offer the potential to improve structural efficiency by allowing the material composition and/or microstructural features to spatially vary within a component. Additive manufacturing techniques enable the fabrication of such graded materials and structures. While examining several titanium alloys, this paper focuses on Ti-8Al-1Er as it has a unique microstructure that is only feasible when produced by rapid solidification methods like electron beam directed energy deposition, an additive manufacturing process. The results show that, when mixed, Ti-8Al-1Er and commercially-pure titanium uniformly mix at various ratios and the resultant static tensile properties of the mixed alloys behave according to rule-of-mixtures. At discontinuous interfaces between Ti-8Al-1Er and commercially-pure titanium, the crack growth behavior progresses smoothly across the discontinuity as the crack transitions from one crack growth regime into another. Studies on monolithic samples shows the mechanisms of damage in the Ti-8Al-1Er; specifically, that strain localization occurs near grain boundaries of high mis-orientation on the microscale and that twinning and dislocation density is concentrated near erbia-strengthening particles (Er2O3) on the nanoscale.

Newman, John A.↗
NASA NTRSDate not supplied

Design of a GRCop-42 Regeneratively Cooled Thrust Chamber Assembly and Feed System

An additively manufactured thrust chamber assembly was designed and printed using laser powder bed fusion. The NASA-developed material GRCop-42 was used for its high strength and high temperature characteristics. The combustion chamber and nozzle utilize regenerative coolant channels to achieve long duration hot fire tests. Design for additive manufacturing was used to create geometries not easily attainable with traditional machining. The thrust chamber assembly was post processed to ensure print quality and verify for testing. A feed system – encompassing all propellant lines, valves, sensors, and tanks – was designed and built to enable steady state, pressure regulated testing. Pressure transducers, thermocouples, and load cells were placed to enable measurements of the propellant properties and engine performance. Venturis and orifices were used throughout the system to control the flow rates to the thrust chamber. Aside from providing propellants, the feed system provides pressure using nitrogen, and purges the lines during shutdown. The design process for this testing platform is described. A testing campaign on the hardware will be conducted by the Akronauts Rocket Design Team at the University of Akron in Spring 2023.

Dillon M. Petty↗
NASA NTRSDate not supplied

Design of a GRCop-42 Regeneratively Cooled Thrust Chamber Assembly and Feed System

An additively manufactured thrust chamber assembly was designed and printed using laser powder bed fusion. The NASA-developed material GRCop-42 was used for its high strength and high temperature characteristics. The combustion chamber and nozzle utilize regenerative coolant channels to achieve long duration hot fire tests. Design for additive manufacturing was used to create geometries not easily attainable with traditional machining. The thrust chamber assembly was post processed to ensure print quality and verify for testing. A feed system – encompassing all propellant lines, valves, sensors, and tanks – was designed and built to enable steady state, pressure regulated testing. Pressure transducers, thermocouples, and load cells were placed to enable measurements of the propellant properties and engine performance. Venturis and orifices were used throughout the system to control the flow rates to the thrust chamber. Aside from providing propellants, the feed system provides pressure using nitrogen, and purges the lines during shutdown. The design process for this testing platform is described. A testing campaign on the hardware will be conducted by the Akronauts Rocket Design Team at the University of Akron in Spring 2023.

Dillon M. Petty↗
NASA NTRSDate not supplied

TPSAS-NF1676L-32708-DND

Proposed Effort under Advanced Air Transport Technology (AATT): - Select advanced Al alloy with formability and additive manufacturability, high combined strength and toughness - Fabricate single-piece Integrally Stiffened Cylinders (~10 ft. dia. x 10 ft. long) with longitudinal stiffeners - Demonstrate joining technology for assembly of two cylinders into 20-ft. long fuselage structure - Optimize structural design incorporating tailored, selective reinforcement for durability and damage tolerance - Build-up window, door and circumferential ring frames with large-scale additive manufacturing - Structural test to validate manufacturing demonstration, structural models and analysis

Taminger, Karen M↗
NASA NTRSDate not supplied

Calorimeter Heat Flux Trends in NASA’s Subscale Rotating Detonation Rocket Engine

A calorimeter-style rotating detonation rocket engine (RDRE) outer chamber body was designed, additively manufactured in GRCop-42, and hot-fire tested in test cell 105 at NASA Marshall Space Flight Center (MSFC) in Huntsville, AL in August 2024. Steady-state, spatially resolved heat flux and chamber pressure were measured at 13 and 9 locations from the injector face, respectively, for a variety of test conditions and hardware configurations with gaseous methane and oxygen propellants. The 2-in. diameter highly instrumented design, enabled by metal additive manufacturing (AM), allowed for simultaneous measurement of heat flux and chamber pressure through 44 long duration hot-fire tests without failure. Of the 44 tests, only 3 of the tests featured chamber pressures below 100 psia and are discussed in this work. Heat flux trends for this subscale hardware are explored with respect to local propellant mass flux for several different injectors, chamber lengths, and chamber “subsonic” area ratios (contraction ratios). Results show that for increasing chamber pressure, a reduced amount of energy per kilogram of propellant is transferred to the wall. Switching injectors affects the near-face heat flux and chamber pressure profiles. Chamber length does not noticeably affect the heat flux profile but increases bulk heat load. A subsonic area ratio greater than 1 reduces heat losses to the wall compared to a straight annulus case. Equivalence ratio shift did not significantly affect heat flux. Computational fluid dynamics (CFD) and conjugate heat transfer (CHT) analyses were performed to delineate 3-D heat transfer and coolant mass flow maldistribution effects and create a calorimeter transfer function to transform heat flux data and mitigate the profile distortions. Additional CFD/CHT simulations were performed using experimental data as boundary conditions to assess local nucleate boiling propensity during testing and to assess projected hot wall temperatures for future fatigue assessment. Vapor fractions were observed locally for several cases. It is anticipated that this effort will provide a common framework for coolant system design/analysis in calorimeter systems for rocket-based and air-breathing combustors, ensuring greater repeatability in calorimetry measurements across the research community.

Joseph Hernandez-McCloskey↗
NASA NTRS2015

Main Oxidizer Valve Design

A developmental Main Oxidizer Valve (MOV) was designed by NASA-MSFC using additive manufacturing processes. The MOV is a pneumatically actuated poppet valve to control the flow of liquid oxygen to an engine's injector. A compression spring is used to return the valve to the closed state when pneumatic pressure is removed from the valve. The valve internal parts are cylindrical in shape, which lends itself to traditional lathe and milling operations. However, the valve body represents a complicated shape and contains the majority of the mass of the valve. Additive manufacturing techniques were used to produce a part that optimized mass and allowed for design features not practical with traditional machining processes.

Addona, Brad↗
NASA NTRSDate not supplied

The Inspectability Metric: A Formalized System Of Measurement Enabling The Design For Inspection Framework

Nondestructive evaluation (NDE) engineers are often confronted with structural design choices that present challenges to meeting inspection requirements. These challenges, at best, increase the resources needed to design an inspection solution and, at worst, require resource intensive redesign of the structure. If the inspectability of the structure can be determined early in the design cycle, these challenging inspection scenarios can be avoided. The emergence of additive manufacturing has further compounded this problem by enabling the creation of highly optimized structures with no regard to inspection constraints. Design for inspection (DFI) offers a framework to integrate nondestructive evaluation (NDE) into the design process to alleviate the mechanisms that produce uninspectable designs. DFI is the concept of including inspectability in a multi-objective optimization framework so that it can be considered in parallel to other metrics such as mass and manufacturability. This allows rapid evaluation of the trade-off between design metrics to find solutions that meet the inspection needs of a particular material system, structural concept, or vehicle program. To enable DFI, there must be a system by which the inspectability of a structure can be measured. This system must be agile to produce results quickly, it must be versatile to work with the type of incomplete information one would encounter early in the design process (such as lack of inspection requirements), and it must be delivered in a form that is easily understood by designers. To meet this need, this presentation introduces the novel inspectability metric as a system to measure inspectability. The inspectability metric is a standardized, automation friendly procedure that uses simulations to determine inspectability. Along with guidelines to properly process designs and integrate with existing workflows, the inspectability metric provides a suite of simulation tests to interrogate the ability to find defects and the sensitivity to variability. The testing rubric is designed to maximize the coverage of the parameter space while minimizing the number of simulations needed. The inspectability metric has been in development in collaboration with industry partners to ensure compatibility with modern simulation tools and aerospace design workflows. In this study, we will demonstrate how the inspectability metric is able to determine the inspectability of multiple types of structures, including aerospace composites and additively manufactured parts. We will then show how the inspectability score can be plugged into existing design optimization tasks, such as structural sizing algorithms or design for manufacturing (DFM) frameworks.

Design for inspection↗
NASA NTRSDate not supplied

Development of Large-Scale Thrust Chambers using Laser Powder Directed Energy Deposition

Historical manufacturing methods for liquid propulsion combustion chambers have relied on series of tube-walls or slotted channel walls (subsequently brazed or plated) for regenerative cooling paths. Large-scale additive manufacturing techniques offer strong potential to minimize manufacturing lead times and cost for developing liquid propulsion chambers, while maintaining performance metrics of traditionally manufactured hardware. The benefits expand beyond traditional combustion chambers to lesser considered nuclear thermal propulsion chambers where radiation energizes the singular incoming propellant stream instead of an exothermic chemical reaction. While each subset of liquid propulsion chambers reaps similar benefit, the geometric challenges in each design can vary substantially. This manuscript discusses the challenges of large contraction ratio propulsion chambers, bimetallic liners and closeout jackets, and material selection when considering laser powder directed energy deposition. LP-DED presently offers build volumes unattainable by L-PBF systems, required for large diameter thrust chambers. LP-DED typically has faster deposition time and is capable of overhang angles without support material (due to the ability to tilt the build plate and minimize the actual build angle). These benefits come at the cost of feature resolution. Designers and manufacturers should consider the effects of thick-wall features printed parallel to the primary surface versus perpendicular due to distortion. Thick-wall and thin-wall features printed in the same plane can substantially increase build time. Where large-scale L-PBF overlaps in size, there may be limited benefit in the quantity of powder required for the build due to the low capture rate of LP-DED and a case-by-case examination is required.

LP-DED↗
NASA NTRS2019

Manufacturing of Thermoset Polyimide Composites by Laser Sintering

Selective Laser Sintering (SLS) is an additive manufacturing technique that builds 3D models layer by layer using a laser to selectively melt cross sections in powdered polymeric materials, following sequential slices of the computer-aided design (CAD) model. SLS generally uses thermoplastic polymeric powders such as polyamides. The resultant 3D-printed objects are often weaker in their strength compared to traditionally processed materials, due to their higher porosity. This paper described the process development of using melt-processable imide oligomers terminated with reactive 4-phenylethynylphthalic anhydride (4-PEPA) to conduct laser sintering (LS). The first successful 3D-printing of high temperature RTM370 thermoset polyimide carbon fiber composites were further post-cured to promote additional crosslinking for achieving higher temperature (T g = 370°C) capability. Another novel imide oligomer, RTM385-SLS, formulated with a complex melt viscosity [ƞ*] of ~104-105 poise is also suitable for LS. RTM385-SLS resin powder was mixed with 20-25% of hexagonal boron nitride (h-BN) and subjected to LS to print out “Green” specimens which could be further post-cured to afford a thermally conductive but electrically insulating composites with high T g of 385 °C. The cured composite specimens were then subjected to mechanical testing, thermal conductivity and porosity measurements as well as SEM characterization.

additive Manufacturing↗
NASA NTRSDate not supplied

Novel Ceramic Dispersion Strengthened Refractory Metals for Improved Printability and Properties

Refractory metals and alloys are of major interest for nuclear fusion systems, space nuclear power and propulsion, and hypersonic applications due to their desirable properties at elevated temperatures (>1500°C). Limitations of refractory materials include their low ductility, poor oxidation resistance, and high manufacture cost using traditional techniques. Additive manufacturing (AM) can reduce material waste associated with manufacture, but AM fabrication is impacted by the brittleness of these refractory metals, resulting in excessive cracking during printing. Cracking reduces the effectiveness of hot isostatic pressing (HIP) which is commonly used to improve density and mechanical properties of AM components. The goal of this work is to improve refractory metal printability without majorly affecting the material properties which are the main reason these materials are used. Ceramic nanoparticles have been shown to help improve material properties after heat treatment. Results will be shown that demonstrate the effectiveness of adding nanoparticles to refractory metals. Additionally, there will be discussion regarding how these nanoparticles change the effect of heat treatments such as HIP compared with the AM pure metal samples.

Carly J. Romnes↗
NASA NTRSDate not supplied

AM Processes Part 2: Principles of Directed Energy Deposition

Directed Energy Deposition (DED) is one of the metal additive manufacturing processes which finds wider industrial applications, particularly for repair and reclamation, and for large structures. This course helps the attendees to understand the fundamental concepts of DED process and covers the topics such as, how the technology works, different DED processes, materials used, and typical applications where this technology is used. The discussion will have a focus on ASTM F3187 – Standard guide for Directed Energy Deposition of Metals. After completing this webinar the attendees will achieve the following: · Identify and understand the different types of DED processes · Understand how to select a DED process and trade criteria · Understand the various materials used for DED processes · Understand the core parameters for the DED processes · Determine potential parts and end application of DED technology

Additive Manufacturing↗