Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “APEX”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Where's the Beaverhead beef?

Only rare quartz grains with single-set planar (1013) deformation features (PDF's) are present in breccia dikes found in association with uniformly oriented shatter cones that occur over an area 8 x 25 km. This suggests that the Beaverhead shocked rocks come from only the outer part of the central uplift of what must have been a large (greater than 100 km diameter) complex impact structure. An impact event of this magnitude on continental crust (thought to have occurred in late Precambrian or ealy Paleozoic time) could be expected to punctuate local geologic history. Furthermore, although it may now be covered, its scar should remain despite all the considerable subsequent erosion/deposition and tectonism since the impact. The following are three large-scale singularities or anomalies that may reflect the event and mark its source. (1) The Lemhi Arch is a major structural uplift that occurred in late Proterozoic-early Paleozoic time in East Central Idaho and caused the erosion of at least 4 km of sedimentary cover. This may be directly related to the impact. (2) Of the many thrust sheets comprising the Cordilleran belt, the Cabin plate that carries the shocked rocks is unique in that it alone intersected the crystalline basement. It also now marks the apex of the Southwest Montana Recess in the Sevier front. The basement uplift remaining from the impact may have constituted a mechanical obstacle to the advancing thrust sheets in Cretaceous time, causing the recess. (3) What could be interpreted as a roughly circular aeromagnetic anomaly approx. 70 km in diameter can be discerned in the state aeromagnetic map centered about 20 km southeast of Challis, Idaho, in the Lost River range. It is in approximately the right place, and ignoring the possibility that the anomalies have diverse causes and the circular pattern is coincidental, it may mark what remains of the buried central uplift structure.

Hargraves, R. B.↗
NASA NTRS1992

Experimental investigation of the effects of aft blowing with various nozzle exit geometries on a 3.0 caliber tangent ogive at high angles of attack: Forebody pressure distributions

An experimental study of the effects of aft blowing on the asymmetric vortex flow of a slender, axisymmetric body at high angles of attack was conducted. A 3.0 caliber tangent ogive body fitted with a cylindrical afterbody was tested in a wind tunnel under subsonic, laminar flow test conditions. Asymmetric blowing from both a single nozzle and a double nozzle configuration, positioned near the body apex, was studied. Aft blowing was observed to alter the vortex asymmetry by moving the blowing-side vortex closer to the body surface while moving the non-blowing-side vortex further away from the body. The effect of increasing the blowing coefficient was to move the blowing-side vortex closer to the body surface at a more upstream location. The data also showed that blowing was more effective in altering the initial vortex asymmetry at the higher angles of attack than at the lower. The effects of changing the nozzle exit geometry were studied and it was observed that blowing from a nozzle with a low, broad exit geometry was more effective in reducing the vortex asymmetry than blowing from a high, narrow exit geometry.

Chokani, Ndaona↗
NASA NTRS1992

An Embedded Rule-Based Diagnostic Expert System in Ada

Ada is becoming an increasingly popular programming language for large Government-funded software projects. Ada with it portability, transportability, and maintainability lends itself well to today's complex programming environment. In addition, expert systems have also assumed a growing role in providing human-like reasoning capability expertise for computer systems. The integration is discussed of expert system technology with Ada programming language, especially a rule-based expert system using an ART-Ada (Automated Reasoning Tool for Ada) system shell. NASA Lewis was chosen as a beta test site for ART-Ada. The test was conducted by implementing the existing Autonomous Power EXpert System (APEX), a Lisp-based power expert system, in ART-Ada. Three components, the rule-based expert systems, a graphics user interface, and communications software make up SMART-Ada (Systems fault Management with ART-Ada). The rules were written in the ART-Ada development environment and converted to Ada source code. The graphics interface was developed with the Transportable Application Environment (TAE) Plus, which generates Ada source code to control graphics images. SMART-Ada communicates with a remote host to obtain either simulated or real data. The Ada source code generated with ART-Ada, TAE Plus, and communications code was incorporated into an Ada expert system that reads the data from a power distribution test bed, applies the rule to determine a fault, if one exists, and graphically displays it on the screen. The main objective, to conduct a beta test on the ART-Ada rule-based expert system shell, was achieved. The system is operational. New Ada tools will assist in future successful projects. ART-Ada is one such tool and is a viable alternative to the straight Ada code when an application requires a rule-based or knowledge-based approach.

Jones, Robert E.↗
NASA NTRS1992

An investigation of the effects of aft blowing on a 3.0 caliber tangent ogive body at high angles of attack

An experimental investigation of the effects of aft blowing on the asymmetric vortex flow of a slender, axisymmetric body at high angles of attack was conducted. A 3.0 caliber tangent ogive body fitted with a cylindrical afterbody was tested in a wind tunnel under subsonic, laminar flow test conditions. Asymmetric blowing from both a single nozzle and a double nozzle configuration, positioned near the body apex, was investigated. Aft blowing was observed to alter the vortex asymmetry by moving the blowing-side vortex closer to the body surface while moving the non-blowing-side vortex further away from the body. The effect of increasing the blowing coefficient was to move the blowing-side vortex closer to the body surface at a more upstream location. The data also showed that blowing was more effective in altering the initial vortex asymmetry at the higher angles of attack than at the lower. The effects of changing the nozzle exit geometry were investigated and it was observed that blowing from a nozzle with a low, broad exit geometry was more effective in reducing the vortex asymmetry than blowing from a high, narrow exit geometry.

Gittner, Nathan M.↗
NASA NTRS1992

Three-dimensional computational study of asymmetric flows using Navier-Stokes equations

The unsteady, compressible, thin-layer Navier-Stokes equations are used to obtain three-dimensional, asymmetric, vortex-flow solutions around cones and cone-cylinder configurations. The equations are solved using an implicit, upwind, flux-difference splitting, finite-volume scheme. The computational applications cover asymmetric flows around a 5 semi-apex angle cone of unit length at various Reynolds number. Next, a cylindrical afterbody of various length is added to the conical forebody to study the effect of the length of cylindrical afterbody on the flow asymmetry. All the asymmetric flow solutions are obtained by using a short-duration side-slip disturbance.

Cheung, Y. K.↗
NASA NTRS1992

Autonomous power system brassboard

The Autonomous Power System (APS) brassboard is a 20 kHz power distribution system which has been developed at NASA Lewis Research Center, Cleveland, Ohio. The brassboard exists to provide a realistic hardware platform capable of testing artificially intelligent (AI) software. The brassboard's power circuit topology is based upon a Power Distribution Control Unit (PDCU), which is a subset of an advanced development 20 kHz electrical power system (EPS) testbed, originally designed for Space Station Freedom (SSF). The APS program is designed to demonstrate the application of intelligent software as a fault detection, isolation, and recovery methodology for space power systems. This report discusses both the hardware and software elements used to construct the present configuration of the brassboard. The brassboard power components are described. These include the solid-state switches (herein referred to as switchgear), transformers, sources, and loads. Closely linked to this power portion of the brassboard is the first level of embedded control. Hardware used to implement this control and its associated software is discussed. An Ada software program, developed by Lewis Research Center's Space Station Freedom Directorate for their 20 kHz testbed, is used to control the brassboard's switchgear, as well as monitor key brassboard parameters through sensors located within these switches. The Ada code is downloaded from a PC/AT, and is resident within the 8086 microprocessor-based embedded controllers. The PC/AT is also used for smart terminal emulation, capable of controlling the switchgear as well as displaying data from them. Intelligent control is provided through use of a T1 Explorer and the Autonomous Power Expert (APEX) LISP software. Real-time load scheduling is implemented through use of a 'C' program-based scheduling engine. The methods of communication between these computers and the brassboard are explored. In order to evaluate the features of both the brassboard hardware and intelligent controlling software, fault circuits have been developed and integrated as part of the brassboard. A description of these fault circuits and their function is included. The brassboard has become an extremely useful test facility, promoting artificial intelligence (AI) applications for power distribution systems. However, there are elements of the brassboard which could be enhanced, thus improving system performance. Modifications and enhancements to improve the brassboard's operation are discussed.

Merolla, Anthony↗
NASA NTRS1992

Dust and gas jets: Evidence for a diffuse source in Halley's coma

The distribution of dust-scattered intensity in Halley's inner coma is measured with the Vega three-channel spectrometer at three selected wavelengths: 377, 482, and 607 nm. The variation along a cometo-centric radius may be described by a p(sup -s) law where p is the distance between nucleus and optical axis and s is an exponent which is equal to 1 except in an intermediate 3000 less than p less than 7000 km region where s = 1.5. The shape of the radial distribution may be explained with a model including solar radiation pressure effect and quantum scattering efficiencies calculated from Mie theory. Monochromatic images inside an angular sector having its apex at the nucleus show evidence of two dust jets which extend to 40,000 Km. The pixel-to-pixel ratio of two images of dust intensity at 377 and 482 nm shows that the scattered intensity presents an excess of blue coloration in a zone located around the jets between 10,000 and 25,000 km. This coloration is interpreted as being due to a population of sub-micronic grains which result of the fragmentation of dust particles transported in the jets. It is suggested that the diffuse source where an additional quantity of CO was detected might be connected with the presence of a dust jet. In the present scheme, grain particles with a size of several micron or 10 micron would be transported inside a dust jet to distances of several 10,000 km where they would suffer fragmentation and produce sub-micronic particles and a release of gas which would be at the origin of the diffuse source.

Clairemidi, Jacques↗
NASA NTRS1993

DSS-14 subreflector actuator dynamics during the Landers earthquake

The 28 Jun. 1992 Landers earthquake ground motion records at the Echo site (DSS-12 antenna) were adjusted to provide a better match with spectra from the measured Mars site (DSS-14 antenna) instrument tower response. A finite-element model of the antenna structural system was analyzed for response to this ground motion. Dynamic forces and displacements were computed in the locality of components that had failed during the earthquake. Calculated forces in the range of 30,000 to 35,000 lb on failed Y-axis actuator U-joints were consistent with laboratory load tests. The load capacity of these joints was found to be below the range of 34,000 to 42,000 lb. Dynamic amplification factors of from 6 to 16 were computed for the quadripod apex accelerations with respect to the ground accelerations. The largest factor--25--was found at the outboard end of the X-actuator.

Levy, R.↗
NASA NTRS1993

The cone structure and focusing of the electric field of VLF and LF waves at high altitudes of the ionosphere

This paper presents a short review of the frequency and angle dependencies of the electric field radiated by an electric dipole E = E(sub 0)cos(omega)t in a magnetoplasma and detailed results of numerical calculations of (E) in the VLF and LF frequency bands 0.02f(sub b) is less than or equal to F is less than or equal to 0.5f(sub b) in the ionosphere and magnetosphere in the altitude region Z = (800 - 6000) km (F is approximately (4 - 500) kHz and f(sub b) is approximately equal to (1.1 to 0.2) MHz is the electron gyro-frequency). The amplitudes of the electric field have large maxima in four regions: close to the direction of the Earth magnetic field line B(sub 0) (it is the so called Axis field E(sub 0); in the Storey E(sub St); Reversed Storey E(sub RevSt); and Resonance E(sub Res) Cones. The maximal values of E(sub 0), E(sub Res), and E(sub Rev ST) are the most pronounced close to the low hybrid frequency, F is approximately F(sub L). The flux of the electric field is concentrated in very narrow regions, with the apexes angles of the cones delta(beta) is approximately (0.1 - 1) degree. The enhancement and focusing of the electric field increases with altitude starting at Z is greater than 800 km. At Z is greater than or equal to 1000 up to 6000 km, the relative value of E, in comparison with its value at Z equals 800 km is about (10(exp 2) to 10(exp 10)) times larger. Thus, the flux of VLF and LF electromagnetic waves in the Earth magnetoplasma produces and is guided by very narrow pencil beams, similar, let us say, to laser beams.

Alpert, Y. L.↗
NASA NTRS1993

Streamwise vorticity generation and mixing enhancement in free jets by delta-tabs

The effect of triangular tabs, placed at the nozzle exit, on the evolution of free jets is investigated. The effect, a large distortion of the jet cross section and a resultant increase in mixing downstream, has been inferred before to be due to a pair of streamwise vortices originating from each tab. In this paper, the generation mechanism of the stream wise vorticity (omega sub x) is considered first. Two sources are postulated. One is the upstream 'pressure hill', produced by the tab, which appears to be the dominant source. Another is due to vortex filaments shed from the sides of the tab and reoriented downstream by the mean shear of the mixing layer. In the case of a 'delta-tab', a triangular tab with its apex leaning downstream, vorticity from the two sources explain the stronger effect in that configuration. Data on the vorticity evolution for the effect of two delta-tabs are presented, up to twelve jet diameters from the exit, which show that the streamwise vortices persist even at the farthest measurement station. The magnitude of omega sub x-maximum decays continually with distance from the nozzle, its ratio to azimuthal vorticity maximum is found to be about 1/5 everywhere. The relative effect of a delta-tab on jets from an axisymmetric nozzle and a 8:1 rectangular nozzle is also studied. The mixing layer distortion is found to be less pronounced in the rectangular case. The jet mixing, as manifested by the mass flux measured at a downstream station, is increased in the axisymmetric jet but it is decreased in the rectangular jet under consideration by the delta-tab.

Zaman, K. B. M. Q.↗
NASA NTRS1993

Scientific ballooning payload termination loads

NASA's high altitude balloon borne scientific payloads are typically suspended from a deployed flat circular parachute. At flight termination, the recovery train is pyrotechnically separated at the parachute apex and balloon nadir interface. The release of elastic energy stored in the parachute at zero initial vertical velocity in the rarefied atmosphere produces high canopy opening forces that subject the gondola to potentially damaging shock loads. Data from terminations occurring at altitudes to 40 km with payloads up to 2500 kg on parachutes up to 40 m in diameter are presented. Measured loads are markedly larger than encountered via packed parachute deployment for similar canopy loadings. Canopy inflation is significantly suppressed in the early stages and then accelerated during final blossoming. Data interpretation and behavioral phenomena are discussed along with proposed shock attenuation techniques.

Robbins, E.↗
NASA NTRS1991

The X-ray flux dipole of AGNs as an indicator of the local gravitational field

We have investigated the dipole anisotropy of the sky X-ray flux from nearby AGNs to compare with the peculiar motion of the Local Group (LG) using a more extensive sample than that of Miyaji and Boldt (1990). We have sampled 56 low redshift emission-line AGNs (z less than 0.06) from the HEAO 1 A-2 experiment with a flux limit lower than that of Piccinotti et al. (1982) and with a lower galactic latitude cutoff. Our sample shows a significant dipole anisotropy whose apex is only about 30 deg away from the direction of the Local Group's peculiar motion for the objects with z less than 0.015. The dipole growth vs. redshift shows a sharp rise between z = 0.006 and z = 0.015; the amplitude of the dipole is 40 +/- 10 percent of the corresponding monopole at z = 0.015. The outer redshift cutoff is consistent with the results obtained from analyses using optical and IRAS galaxies. The present sample strengthens our previous conclusion that X-ray emission from AGNs traces the underlying mass distribution as strongly as optical and IR emission from galaxies.

Miyaji, Takamitsu↗
NASA NTRS1992

Lessons learned from the Autonomous Power System

The Autonomous Power System (APS) project at the NASA Lewis Research Center is designed to demonstrate the applications of integrated intelligent diagnosis, control and scheduling techniques to space power distribution systems. The project consists of three elements: the Autonomous Power Expert System (APEX) for Fault Diagnosis, Isolation, and Recovery (FDIR); the Autonomous Intelligent Power Scheduler (AIPS) to efficiently assign activities start times and resources; and power hardware (Brassboard) to emulate a space-based power system. The APS project had been through one design iteration. Each of the three elements of the APS project has been designed, tested, and integrated into a complete working system. After these three portions were completed, an evaluation period was initiated. Each piece of the system was critiqued based on individual performance as well as the ability to interact with the other portions of the APS project. These critiques were then used to determine guidelines for new and improved components of the APS system.

Ringer, Mark J.↗
NASA NTRS1993

High-resolution mid-infrared imaging and astrometry of the nucleus of the Seyfert galaxy NGC 1068

The Goddard Infrared Array Camera was used to obtain a high resolution image of the nucleus of NGC 1068 at 12.4 microns. In addition, the peak emission at 12.4 microns relative to the peak of the optical continuum was determined. The distribution of the 12.4 micron emission relates to both the forbidden O III 5007A 'ionization cone' and the optical continuum emission imaged by HST. This distribution is also found to have an alignment perpendicular to the plane of a putative molecular torus. It is suggested that the extended mid-infrared emission is thermal radiation from dust in circumnuclear clouds heated by the collimated optical/UV AGN source. A portion of the unresolved 12.4 micron emission possibly originates from the torus. The infrared emission peak is found to coincide with the apex of the ionization cone, which is presumed to be the location of the torus.

Braatz, J. A.↗
NASA NTRS1990

The Black Pearl mine, Arizona - Wolframite veins and stockscheider pegmatite related to an albitic stock

Wolframite-bearing quartz veins flanked by greisen alteration occur at and near the Black Pearl mine, Yavapai County, Arizona. The veins are genetically related to a small albitite stock, and cut a series of Proterozoic metasedimentary and intrusive rocks. The largest vein, the only one mined, is located at the apex of the stock. Field relations imply that this stock is a late-stage differentiate of time 1.4-Ga anorogenic Lawler Peak batholith, which crops out about 3 km to the south. The albitites are of igneous origin and have suffered only minor deuteric alteration. A thin (1 to 2 m) pegmatite unit ('stockscheider') occurs at the contact of the Black Pearl Albitite stock with the country rocks. Directional indicators and other evidence suggest that the pegmatite was formed in the presence of a volatile-rich fluid phase close to the time of magma emplacement. The sudden change from coarse-grained microcline-rich pegmatite to fine-grained, albite-rich albitite suggests pressure quenching, possibly due to escape of fluids up the Black Pearl vein. Stockscheider-like textures typically occur near the apical contacts of productive plutons. The presence or absence of this texture is a useful guide in prospecting for lithophile metal deposits.

Schmitz, Christopher↗
NASA NTRS1993

Formation, levitation, and stability of prominences in the magnetized solar atmosphere

The dynamic formation of prominences in the initial magnetothermal equilibrium and their stability to sideward displacements are investigated focusing on the structure of the 2D solar atmosphere in the presence of coronal arcades or loops. A model based on 2D magnetohydrodynamic equations takes into account gravity, compressible flows, heating, radiation, anisotropic thermal conduction, and coupling to a deep chromosphere. It is found that prominences in simple arcades characterized by magnetic field with significant curvature at the apex are unstable to a lateral displacement.

Drake, J. F.↗
NASA NTRS1993

Streamwise vorticity generation and mixing enhancement in free jets by 'delta-tabs'

The effect of triangular tabs, placed at the nozzle exit, on the evolution of free jets is investigated. The effect, a large distortion of the jet cross section and a resultant increase in mixing downstream, has been inferred before to be due to a pair of streamwise vortices originating from each tab. In this paper, the generation mechanism of the streamwise vorticity (omega sub x) is considered first. Two sources are postulated. One is the upstream 'pressure hill', produced by the tab, which appears to be the dominant source. Another is due to vortex filaments shed from the sides of the tab and reoriented downstream by the mean shear of the mixing layer. In the case of a 'delta-tab', a triangular tab with its apex leaning downstream, vorticity from the two sources explain the stronger effect in that configuration. Data on the vorticity evolution for the effect of two delta-tabs are presented, up to twelve jet diameters from the exit, which show that the streamwise vortices persist even at the farthest measurement station. The magnitude of omega sub x-maximum decays continually with distance from the nozzle, its ratio to azimuthal vorticity maximum is found to be about 1/5 everywhere. The relative effect of a delta-tab on jets from an axisymmetric nozzle and a 8:1 rectangular nozzle is also studied. The mixing layer distortion is found to be less pronounced in the rectangular case. The jet mixing, as manifested by the mass flux measured at a downstream station, is increased in the axisymmetric jet but it is decreased in the rectangular jet under consideration by the delta-tab.

Zaman, K. B. M. Q.↗
NASA NTRS1951

Approximate methods for calculating the flow about nonlifting bodies of revolution at high supersonic airspeeds

Explicit expressions are developed which yield the Mach number and pressure distributions on the surfaces of pointed nonlifting bodies of revolution operating at high supersonic airspeeds and at values of the hypersonic similarity parameter (ratio of free-stream Mach number to slenderness ratio) greater than 1. Very simple explicit expressions are obtained for these distributions in the special case of slender bodies. In the case of cones, the analytic solutions accurately define the entire flow field over a wide range of free-stream Mach numbers and apex angles.

Eggers, A J , Jr↗