SEARCH · Engineering Papers

Results for “yaw control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

All sources NASA NTRS DOE OSTI

NASA NTRS1986

Independent Orbiter Assessment (IOA): Analysis of the ascent thrust vector control actuator subsystem

The results of the Independent Orbiter Assessment (IOA) of the Failure Modes and Effects Analysis (FMEA) and Critical Items List (CIL) are presented. The IOA approach features a top-down analysis of the hardware to determine failure modes, criticality, and potential critical items. To preserve independence, this analysis was accomplished without reliance upon the results contained within the NASA FMEA/CIL documentation. The independent analysis results for the Ascent Thrust Vector Control (ATVC) Actuator hardware are documented. The function of the Ascent Thrust Vector Control Actuators (ATVC) is to gimbal the main engines to provide for attitude and flight path control during ascent. During first stage flight, the SRB nozzles provide nearly all the steering. After SRB separation, the Orbiter is steered by gimbaling of its main engines. There are six electrohydraulic servoactuators, one pitch and one yaw for each of the three main engines. Each servoactuator is composed of four electrohydraulic servovalve assemblies, one second stage power spool valve assembly, one primary piston assembly and a switching valve. Each level of hardware was evaluated and analyzed for possible failure modes and effects. Criticality was assigned based upon the severity of the effect for each failure mode. Critical failures resulting in loss of ATVC were mainly due to loss of hydraulic fluid, fluid contamination and mechanical failures.

Wilson, R. E.↗

NASA NTRS2013

Sweeping Jet Actuators - A New Design Tool for High Lift Generation

Active Flow Control (AFC) experiments performed at the Caltech Lucas Wind Tunnel on a generic airplane vertical tail model proved the effectiveness of sweeping jets in improving the control authority of a rudder. The results indicated that a momentum coefficient (C(sub u)) of approximately 2% increased the side force in excess of 50% at the maximum conventional rudder deflection angle in the absence of yaw. However, sparsely distributed actuators providing a collective C(sub u) approx. = 0.1% were able to increase the side force in excess of 20%. This result is achieved by reducing the spanwise flow along the swept back rudder and its success is attributed to the large sweep back angle of the vertical tail. This current effort was sponsored by the NASA Environmentally Responsible Aviation (ERA) project.

Graff, Emilio↗

NASA NTRS2024

Assessment of Secondary Pitot Probe Locations on a Small UAS

Urban Air Mobility (UAM) and Advanced Air Mobility (AAM) have been at the forefront of many aeronautical discussions because of the potential revolutionary improvement to urban transportation. In this study, a representative Research Aircraft for eVTOL Enabling techNologies, Sub-scale Wind Tunnel Flight Test (RAVEN SWFT) nosecone was placed inside the NASA Langley Research Center’s 12-Foot Low-Speed Wind Tunnel with a pitot-static assembly installed. The study aimed to determine a suitable location and orientation of the pitot-static assembly on the nose of the vehicle, which consists of two airspeed sensors: one for the flight controller and one for data collection. The dynamic pressure was varied from 0.5 to 5psf for each test point. Additionally, three different offset distances from the center boom and three different angles for the flight controller pitot tube were tested. The data from both of the pitot tube assemblies were compared to the wind tunnel and the Aeroprobe pitot tube. The results show the flight controller pitot tube performs better when it is placed further away from the nosecone, regardless of the angle. The results also show that the angle does not affect the accuracy of the pitot tube when the vehicle yaws or pitches regardless of the mounting angle and location. The study provides useful insights for the design of the airspeed measurement systems on small Uncrewed Aerial Systems (sUAS), which can be applied to other UAM and AAM applications.

AAM↗

NASA NTRS1992

Measurement of the passive attitude control performance of a recovered spacecraft

A novel silver detector incorporated in the Long Duration Exposure Facility (LDEF) has been used to measure the attitude stability of the vehicle. It is thereby established that the LDEF spacecraft maintained a very stable attitude during its nearly 6-year-long flight, notwithstanding a small offset yaw of 8.0 +/- 0.4 deg clockwise from nominal attitude (as viewed from space) and a +/- 0.2-deg oscillation about this offset yaw. LDEF experiments which depend on orientation relative to the forward direction may need to be corrected for the angular offset.

Gregory, J. C.↗

NASA NTRS1983

An aerodynamic assessment of various supersonic fighter airplanes based on Soviet design concepts

The aerodynamic, stability, and control characteristics of several supersonic fighter airplane concepts were assessed. The configurations include fixed-wing airplanes having delta wings, swept wings, and trapezoidal wings, and variable wing-sweep airplanes. Each concept employs aft tail controls. The concepts vary from lightweight, single engine, air superiority, point interceptor, or ground attack types to larger twin-engine interceptor and reconnaissance designs. Results indicate that careful application of the transonic or supersonic area rule can provide nearly optimum shaping for minimum drag for a specified Mach number requirement. Through the proper location of components and the exploitation of interference flow fields, the concepts provide linear pitching moment characteristics, high control effectiveness, and reasonably small variations in aerodynamic center location with a resulting high potential for maneuvering capability. By careful attention to component shaping and location and through the exploitation of local flow fields, favorable roll-to-yaw ratios may result and a high degree of directional stability can be achieved.

Spearman, M. L.↗

NASA NTRS1947

Flight Measurements of the Lateral Control Characteristics of Narrow-Chord Ailerons on the Trailing Edge of a Full-Span Slotted Flap

Results are presented of light tests made to determine the effect of flap deflection on the lateral control characteristics of a modified brewster f2a-2 airplane equipped with partial-span narrow-chord ailerons on the trailing edge of a full-span NACA slotted flap. The investigation included determination of the rolling and yawing characteristics of the airplane in abrupt aileron rolls with the slotted flap at various settings ranging from 0 degree to about 40 degrees. The results showed that the effectiveness of the ailerons was greatly reduced at flap deflections greater than about 20 degrees. For flap deflections up to about 20 degrees, the aileron effectiveness was about the same as with flaps retracted, but the adverse yawing velocity developed in the abrupt aileron rolls was somewhat increased.

Sawyer, Richard H↗

NASA NTRS1961

Low-Speed Investigation of the Effects of Large Wing-Sideslip Angles on the Aerodynamic Characteristics of Two Arrow-Wing-Fuselage Arrangements

A wind-tunnel investigation has been made of two methods proposed to reduce the high sinking speeds and improve the landing characteristics of low-aspect-ratio hypersonic airplanes by placing the wing at large angles of sideslip to increase its effective aspect ratio. The models investigated had conical fuselages and arrow wings, with a leading-edge sweep-back of 77.4deg, an aspect ratio of 1.23, and a 4-percent-thick straight-wedge section. For one model, the wing was pivoted on the fuselage to angles of wing sideslip from 0 to 90deg. For the other model, the wing was fixed to the fuselage, and the wing and fuselage were yawed together to sideslip angles from 0 to 90deg. The investigation was made in the Langley 300-MPH 7- by 10-foot tunnel for an angle-of-attack range from -8 to above 28deg. Longitudinal stability and control through the use of horizontal tails with elevators was studied on the pivoted-wing configuration. The roll control for both configurations was studied with deflection of the apex portion of the wing about an axis along the wing center line. The use of flaps with the wing at large sideslip angles was also investigated.

Thomas G Gainer↗

NASA NTRS2008

Using Pressure- and Temperature-Sensitive Paint for Global Surface Pressure and Temperature Measurements on the Aft-Body of a Capsule Reentry Vehicle

Pressure Sensitive Paint (PSP) and Temperature Sensitive Paint (TSP) were used to visualize and quantify the surface interactions of reaction control system (RCS) jets on the aft body of capsule reentry vehicle shapes. The first model tested was an Apollo-like configuration and was used to focus primarily on the effects of the forward facing roll and yaw jets. The second model tested was an early Orion Crew Module configuration blowing only out of its forward-most yaw jet, which was expected to have the most intense aerodynamic heating augmentation on the model surface. This paper will present the results from the experiments, which show that with proper system design, both PSP and TSP are effective tools for studying these types of interaction in hypersonic testing environments.

Watkins, A. Neal↗

NASA NTRS1986

Precision attitude determination and control using gyros and earth sensor

A novel scheme to estimate the biases present in the gyros and the attitude of three-axis stabilized earth pointing spacecraft using the outputs of gyros and earth sensor is presented. The earth sensor pitch output is averaged every orbit to provide pitch gyro bias correction. Roll and yaw gyro biases are determined by averaging the earth sensor roll output every quarter orbit and suitably combining the four quarter orbit averages obtained in each orbit. Yaw attitude information is also required once every orbit. Simulation studies including error sources due to earth sensor, gyros, yaw sensor and horizon radiance uncertainty in the winter poles showed that attitude determination accuracy of 0.01-0.03 deg (3 sigma) can be achieved about all the axes.

Rajaram, S.↗

NASA NTRS2016

Rotary Balance Wind Tunnel Testing for the FASER Flight Research Aircraft

Flight dynamics research was conducted to collect and analyze rotary balance wind tunnel test data in order to improve the aerodynamic simulation and modeling of a low-cost small unmanned aircraft called FASER (Free-flying Aircraft for Sub-scale Experimental Research). The impetus for using FASER was to provide risk and cost reduction for flight testing of more expensive aircraft and assist in the improvement of wind tunnel and flight test techniques, and control laws. The FASER research aircraft has the benefit of allowing wind tunnel and flight tests to be conducted on the same model, improving correlation between wind tunnel, flight, and simulation data. Prior wind tunnel tests include a static force and moment test, including power effects, and a roll and yaw damping forced oscillation test. Rotary balance testing allows for the calculation of aircraft rotary derivatives and the prediction of steady-state spins. The rotary balance wind tunnel test was conducted in the NASA Langley Research Center (LaRC) 20-Foot Vertical Spin Tunnel (VST). Rotary balance testing includes runs for a set of given angular rotation rates at a range of angles of attack and sideslip angles in order to fully characterize the aircraft rotary dynamics. Tests were performed at angles of attack from 0 to 50 degrees, sideslip angles of -5 to 10 degrees, and non-dimensional spin rates from -0.5 to 0.5. The effects of pro-spin elevator and rudder deflection and pro- and anti-spin elevator, rudder, and aileron deflection were examined. The data are presented to illustrate the functional dependence of the forces and moments on angle of attack, sideslip angle, and angular rate for the rotary contributions to the forces and moments. Further investigation is necessary to fully characterize the control effectors. The data were also used with a steady state spin prediction tool that did not predict an equilibrium spin mode.

Denham, Casey↗

NASA NTRS1996

Yaw Motion Cues in Helicopter Simulation

A piloted simulation that examined the effects of yaw motion cues on pilot-vehicle performance, pilot workload, and pilot motion perception was conducted on the NASA Ames Vertical Motion Simulator. The vehicle model that was used represented an AH-64 helicopter. Three tasks were performed in which only combinations of vehicle yaw and vertical displacement were allowed. The commands issued to the motion platform were modified to present the following four motion configurations for a pilot located forward of the center of rotation: (1) only the linear translations, (2) only the angular rotation, (3) both the linear translations and the angular rotation, and (4) no motion. The objective data indicated that pilot-vehicle performance was reduced and the necessary control activity increased when linear motion was removed; however, the lack of angular rotation did not result in a measured degradation for almost all cases. Also, pilots provided subjective assessments of their compensation required, the motion fidelity, and their judgment of whether or not linear or rotational cockpit motion was present. Ratings of compensation and fidelity were affected only by linear acceleration, and the rotational motion had no significant impact. Also, when only linear motion was present, pilots typically reported the presence of rotation. Thus, linear acceleration cues, not yaw rotational cues, appear necessary to simulate hovering flight.

Schroeder, Jeffrey A.↗

NASA NTRS1931

The Steady Spin

With the object of further clarifying the problem of spinning, the equilibrium of the forces and moments acting on an airplane is discussed in light of the most recent test data. Convinced that in a spin the flight attitude by only small angles of yaw is more or less completely steady, the study is primarily devoted to an investigation of steady spin with no side slip. At small angles, wholly arbitrary and perfectly steady spins may be forced, depending on the type of control displacements. But at large angles only very steep and only "approaching steady" spins are possible, no matter what the control displacements.

Fuchs, Richard↗

DOE OSTI2021

Flow Redirection and Induction in Steady State (FLORIS) Wind Plant Power Production Data Sets

This dataset contains turbine- and plant-level power outputs for 252,500 cases of diverse wind plant layouts operating under a wide range of yawing and atmospheric conditions. The power outputs were computed using the Gaussian wake model in NREL's FLOw Redirection and Induction in Steady State (FLORIS) model, version 2.3.0. The 252,500 cases include 500 unique wind plants generated randomly by a specialized Plant Layout Generator (PLayGen) that samples randomized realizations of wind plant layouts from one of four canonical configurations: (i) cluster, (ii) single string, (iii) multiple string, (iv) parallel string. Other wind plant layout parameters were also randomly sampled, including the number of turbines (25-200) and the mean turbine spacing (3D-10D, where D denotes the turbine rotor diameter). For each layout, 500 different sets of atmospheric conditions were randomly sampled. These include wind speed in 0-25 m/s, wind direction in 0 deg.-360 deg., and turbulence intensity chosen from low (6%), medium (8%), and high (10%). For each atmospheric inflow scenario, the individual turbine yaw angles were randomly sampled from a one-sided truncated Gaussian on the interval 0 deg.-30 deg. oriented relative to wind inflow direction. This random data is supplemented with a collection of yaw-optimized samples where FLORIS was used to determine turbine yaw angles that maximize power production for the entire plant. To generate this data, a subset of cases were selected (50 atmospheric conditions from 50 layouts each for a total of additional 2,500 cases) for which FLORIS was re-run with wake steering control optimization. The IEA onshore reference turbine, which has a 130 m rotor diameter, a 110 m hub height, and a rated power capacity of 3.4 MW was used as the turbine for all simulations. The simulations were performed using NREL's Eagle high performance computing system in February 2021 as part of the Spatial Analysis for Wind Technology Development project funded by the U.S. Department of Energy Wind Energy Technologies Office. The data was collected, reformatted, and preprocessed for this OEDI submission in May 2023 under the Foundational AI for Wind Energy project funded by the U.S. Department of Energy Wind Energy Technologies Office. This dataset is intended to serve as a benchmark against which new artificial intelligence (AI) or machine learning (ML) tools may be tested. Baseline AI/ML methods for analyzing this dataset have been implemented, and a link to their repository containing those models has been provided. The .h5 data file structure can be found in the GitHub repository under explore_wind_plant_data_h5.ipynb.

AI↗

DOE OSTI2022

Impacts of wind field characteristics and non-steady deterministic wind events on time-varying main-bearing loads

Abstract. This work considers the characteristics and drivers of the loads experienced by wind turbine main bearings. Simplified load response models of two different hub and main-bearing configurations are presented, representative of both inverting direct-drive and four-point-mounted geared drivetrains. The influences of deterministic wind field characteristics, such as wind speed, shear, yaw offset, and veer, on the bearing load patterns are then investigated for similarity scaled 5, 7.5, and 10 MW reference wind turbine models. Main-bearing load response in cases of deterministic gusts and extreme changes in wind direction are also considered for the 5 MW model. Perhaps surprisingly, veer is identified as an important driver of main-bearing load fluctuations. Upscaling results indicate that similar behaviour holds as turbines become larger, but with mean loads and load fluctuation levels increasing at least cubically with the turbine rotor radius. Strong links between turbine control and main-bearing load response are also observed.

17 WIND ENERGY↗

NASA NTRSDate not supplied

Analysis of Handling Qualities and Power Consumption for Urban Air Mobility (UAM) eVTOL Quadrotors with Degraded Heave Disturbance Rejection and Control Response

A piloted handling qualities study of urban air mobility (UAM) electric vertical take-off and landing (eVTOL) quadrotors was performed utilizing the Vertical Motion Simulator (VMS) facility at NASA Ames Research Center. Rotor speed and variable pitch-controlled variants of a six-passenger conceptual design vehicle were assessed with different levels of degradation to control response and disturbance rejection bandwidth (DRB) in the heave axis. In previous work, preliminary trends across several handling quality rating categories reflected the effects of these degradations. Additionally, the impact of using different test standards and turbulence on the ratings were discussed. This paper elaborates on those results, but also provides insight into unexpected trends observed during the study including: a disharmony in attitude response, subpar ratings for the baseline Level 1 performance vehicle, and excessive drift and yaw couplings observed in a lateral reposition maneuver. Moreover, shortcomings of the handling quality scales and comparisons of power consumption among the vehicles in the various test conditions are presented.

Handling Qualities↗

NASA NTRS1952

Free-Flight-Tunnel Investigation of the Dynamic Stability and Control Characteristics of a Chance Vought F7U-3 Airplane in Towed Flight

As part of a program to determine the feasibility of using a fighter airplane as a parasite in combination with a Consolidated Vultee RB-36 for long-range reconnaissance missions (project FICON), an experimental investigation has been made in the Langley free-flight tunnel to determine the dynamic stability and control characteristics of a 1/17.5-scale model of a Chance Vought F7U-3 airplane in several tow configurations. The investigation consisted of flight tests in which the model was towed from a strut in the tunnel by a towline and by a direct coupling which provided complete angular freedom. The tests with the direct coupling also included a study of the effect of spring restraint in roll in order to simulate approximately the proposed full-scale arrangement in which the only freedom is that permitted by the flexibility of the launching and retrieving trapeze carried by the-bomber. For the tow configurations in which a towline was used (15 and 38 feet full scale), the model had a very unstable lateral oscillation which could not be controlled. The stability was also unsatisfactory for the tow configuration in Which the model was coupled directly to the strut with complete angular freedom. When spring restraint in roll was added, however, the stability was satisfactory. The use of the yaw damper which increased the damping in yaw to about six times the normal value of the model appeared to have no appreciable effect on the lateral oscillations in the towline configurations, but produced a slight improvement in the case of the direct coupling configurations. The longitudinal stability was satisfactory for those cases in which the lateral stability was good enough to permit study of longitudinal motions.

Grana, David C.↗

NASA NTRSDate not supplied

Core Stage TVC Systems Engineering Challenges in Reusing Heritage Hardware

The Space Launch System (SLS) Core Stage (CS) Thrust Vector Control (TVC) system is comprised of 8 mechanical feedback Shuttle heritage Type III TVC actuators and four RS-25 engines, each attached to a Shuttle heritage gimbal block/bearing. Two actuators are used to move each engine in two planes perpendicular to one another (i.e., pitch and yaw). The TVC system design leverages hardware from the Space Shuttle program as well as new hardware designed specifically for the Core Stage. The Space Shuttle heritage hardware directly reused on SLS includes the Orbiter TVC hydraulic servo-actuators (with two slight design modifications), the Orbiter hydraulic circulation pumps, the Orbiter gimbal block/bearing, and the Solid Rocket Booster hydraulic pumps. The Core Auxiliary Power Unit (CAPU) is derived from the Orbiter Auxiliary Power Unit (APU). The Orbiter and Solid Rocket Booster APU turbines are powered by hot gas produced by catalyzed hydrazine decomposition. On the SLS Core Stage, the CAPU turbine is spun using cold gas tapped-off from the RS-25 to CS liquid hydrogen autogenous pressurization line. While direct reuse or slight modification of existing hardware may seem to be a triple-win for a program in cost, schedule, and technical risk mitigation, those benefits can only be realized when its degree of application in a new system is carefully and thoughtfully managed. The heritage hardware reuse should be prescribed within the heritage design capability and reuse environments must lie within the envelope of heritage qualification testing. Despite the significant test and flight experience of the Shuttle heritage hardware components, successful integration with the newly designed CS TVC components and incorporation into the stage design proved to be a challenge which required re-qualification of the heritage hardware as well as thorough integrated testing to support flight certification. Examples of the challenges that were overcome include: re-qualifying heritage hardware to survive new shock and vibration environments, certifying performance of extensively modified heritage hardware, regenerating design insight due to lack of available heritage vendor data, showing compliance to modern structural design standards, translation of heritage requirements for analog avionics to modern digital avionics, and interfacing heritage mechanical hardware with newly designed avionics. This paper is the second installment in a seven-paper series surveying the design, engineering, test validation, and flight performance of the Core Stage Thrust Vector Control system. This paper will discuss several engineering challenges encountered during the development process for SLS CS TVC and how they were successfully overcome to reach flight readiness.

Thrust Vector Control↗

NASA NTRSDate not supplied

Space Launch System: Core Stage Thrust Vector Control Systems Engineering Challenges in Reusing Heritage Hardware

Thrust Vector Control↗