Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “thermal efficiency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

Numerical Analysis of Fuel Effects on Advanced Compression Ignition Using a Cooperative Fuel Research Engine Computational Fluid Dynamics Model

Growing environmental concerns and demand for a better fuel economy are driving forces that motivate the research for more advanced engines. Multi-mode combustion strategies have gained attention for their potential to provide high thermal efficiency and low emissions for light-duty applications. These strategies target optimizing the engine performance by correlating different combustion modes to load operating conditions. The extension from boosted spark ignition (SI) mode at high loads to advanced compression ignition (ACI) mode at low loads can be achieved by increasing the compression ratio and utilizing intake air heating. Further, in order to enable an accurate control of intake charge condition for ACI mode and rapid mode-switches, it is essential to gain fundamental insights into the autoignition process. Within the scope of ACI, homogeneous charge compression ignition (HCCI) mode is of significant interest. It is known for its potential benefits, operation at low fuel consumption, low NOx, and particulate matter (PM) emissions. In the present work, a virtual Cooperative Fuel Research (CFR) engine model is used to analyze fuel effects on ACI combustion. In particular, the effect of fuel octane sensitivity (S) (at constant Research Octane Number (RON)) on autoignition propensity is assessed under beyond-RON (BRON) and beyond-MON (BMON) ACI conditions. The three-dimensional CFR engine computational fluid dynamics (CFD) model employs a finite-rate chemistry approach with a multi-zone binning strategy to capture autoignition. Two binary blends with Research Octane Number (RON) of 90 are chosen for this study: primary reference fuel (PRF) with S = 0 and toluene–heptane (TH) blend with S = 10.8, representing paraffinic and aromatic gasoline surrogates. Reduced mechanisms for these blends are generated from a detailed gasoline surrogate kinetic mechanism. Simulation results with the reduced mechanisms are validated against experimental data from an in-house CFR engine, with respect to in-cylinder pressure, heat release rate, and combustion phasing. Thereafter, the sensitivity of combustion behavior to ACI operating condition (BRON versus BMON), air-fuel ratio (λ = 2 and 3), and engine speed (600 and 900 rpm) is analyzed for both fuels. It is shown that the sensitivity of a fuel’s autoignition characteristics to λ and engine speed significantly differs at BRON and BMON conditions. Moreover, this sensitivity is found to vary among fuels, despite the same RON. It is also observed that the presence of low-temperature heat release (LTHR) under BRON condition leads to more sequential autoignition and longer combustion duration than BMON condition. Finally, the study indicates that the octane index (OI) fails to capture the trend in the variation of autoignition propensity with S under the BMON condition.

33 ADVANCED PROPULSION SYSTEMS↗

From Highly Purified Boron Nitride to Boron Nitride-Based Heterostructures: An Inorganic Precursor-Based Strategy

The current approaches used to fabricate hexagonal boron nitrides (h-BN) from boron trioxide and urea always results in contamination of the h-BN product with carbon/oxygen. Thus, discovering a facile way of mass producing high-purity h-BN remains a challenge. A simple yet highly efficient thermal treatment approach to large-scale fabrication of nanoporous h-BN with high yield, high purity, and high crystallinity is described using NaNH 2 and NaBH 4 as the oxygen- and carbon-free precursors. The unique properties of inorganic metal salts, i.e., high melting point and strong electrostatic interaction with carbon substrates, render this strategy suitable for the production of homogeneous h-BN/mesoporous carbon and h-BN/carbon nanotube heterostructures of high crystallinity, high h-BN dispersity, and with a strong interfacial effect. Therefore, these unique features make them promising candidates for supercapacitor applications, resulting a significantly enhanced specific capacitance. This study provides new insight into the fabrication of high-purity h-BN and h-BN-based heterostructures thus expanding their application in the field of energy storage and transformation.

36 MATERIALS SCIENCE↗

Nanohybrid of Silver‐MXene: A Promising Sorbent for Iodine Gas Capture from Nuclear Waste

The increasing reliance on nuclear energy as a significant low-carbon power source necessitates effective solutions for managing radioactive emissions. This study introduces a novel application of MXene nanohybrids, specifically silver-MXene (Ag-Ti 3 C 2 T x ), as an effective sorbent for radioiodine off-gas capture at an operating temperature of 150 °C. Through comprehensive material characterization, including X-ray diffraction, scanning and transmission electron microscopies, energy-dispersive X-ray spectroscopy, Raman spectroscopy, thermogravimetric analysis, inductively coupled plasma optical emission spectroscopy, and gas sorption analyses, the successful loading of Ag nanoparticles onto Ti 3 C 2 T x is confirmed and the subsequent formation of AgI upon iodine capture. The results demonstrate that Ag-Ti 3 C 2 T x exhibits superior iodine uptake compared to traditional silver-based sorbents such as silver mordenite zeolite (AgZ) and silver-functionalized silica aerogel (AgAero). The Ag-Ti 3 C 2 T x achieves an iodine loading of 946 mg g −1 , significantly outperforming AgZ (131 mg g −1 ). These findings highlight the potential of Ag-Ti 3 C 2 T x as a highly efficient, thermally stable sorbent for radioiodine capture, and potentially addressing key limitations of existing materials.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Integrated Capture and Conversion of CO 2 to Methane Using a Water-lean, Post-Combustion CO 2 Capture Solvent

Integrated Carbon Capture and Conversion of CO 2 into materials (IC3M) is an attractive solution to meet the global energy demand, reduce our dependence on fossil fuels and lower CO 2 emissions. In this work, using a water-lean post combustion capture solvent, (N-(2-ethoxyethyl)-3-morpholinopropan-1-amine) (2-EEMPA), >90% conversion of captured CO2 to hydrocarbons, mostly methane, is achieved in the presence of a heterogenous Ru catalysts under relatively mild reaction conditions (170 °C and <15 bar H 2 pressure). The catalytic performance was better in 2-EEMPA than aqueous 5M monoethanol amine (MEA). Operando NMR study showed in-situ formation of N-formamide intermediate, which underwent further hydrogenation to form methane and other higher hydrocarbons. The technoeconomic analyses (TEA) showed that the proposed integrated process can potentially improve the thermal efficiency by 5% and reduce the total capital investment and minimum synthetic natural gas (SNG) selling price by 32% and 12% respectively compared to conventional Sabatier process, highlighting the energetic and economic benefits of integrated capture and conversion. Methane derived from CO 2 and renewable H 2 source is an attractive fuel, and it has a great potential as a renewable hydrogen carrier as an environmentally responsible carbon capture and utilization approach.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Doped calcium manganites for advanced high-temperature thermochemical energy storage

Developing efficient thermal storage for concentrating solar power plants is essential to reducing the cost of generated electricity, extending or shifting the hours of operation, and facilitating renewable penetration into the grid. Perovskite materials of the CaB x Mn 1-x O 3-δ family, where B = Al or Ti, promise improvements in cost and energy storage density over other perovskites currently under investigation. Thermogravimetric analysis of the thermal reduction and reoxidation of these materials was used to extract equilibrium thermodynamic parameters. Lastly, the results demonstrate that these novel thermochemical energy storage media display the highest reaction enthalpy capacity for perovskites reported to date, with a reaction enthalpy of 390 kJ/kg, a 56% increase over previously reported compositions.

25 ENERGY STORAGE↗

Integrated Silicon Fourier Transform Spectrometer with Broad Bandwidth and Ultra‐High Resolution

An ultra-high resolution Fourier transform spectrometer (FTS) realized in silicon photonic platform that can operate with broad band, narrow band as well as a combination of broad band and narrow band signals is reported. The ultra-high resolution of the spectrometer is achieved by exploiting multiple techniques: a Michelson interferometer (MI) structure to increase the optical path delay (OPD), a hybrid waveguide design to reduce insertion loss, an optimized heater and air trenches to achieve higher thermal efficiency. Here, to further increase the OPD of the spectrometer to increase its resolution, a novel multiple interferometers approach is employed which combines balanced MI with N statically imbalanced MIs, thereby increasing the OPD of a single MI by factor of N + 1. An FTS spectrometer consisting of N = 2 such MIs is fabricated and experimentally characterized using unknown broad bandwidth input signal spectra of about 180 nm centered around 1550 nm, a narrow line laser input signal, and a combination of broad and narrow band signals demonstrating spectral resolution of about 0.16 nm.

Li, Ang↗

Solving Recent Challenges for Wrought Ni-Base Superalloys

This paper reviews the status of technology in design and manufacture of new wrought 21 polycrystalline Ni-base superalloys for critical engineering applications. There is a strong 22 motivation to develop new alloys that are capable of operating at higher temperatures to 23 realise improvements in thermal efficiency, which are necessary to achieve environmental 24 targets for reduced emissions of harmful green-house gases. From the aerospace sector, 25 the development of new powder metallurgy and ingot metallurgy alloys are discussed for 26 disk rotor and static applications. New compositions for powder metallurgy contain about 27 50-55% of gamma prime (γ') strengthening precipitates to ensure components operate 28 successfully at temperatures up to 788°C (1450°F). In contrast, new compositions for ingot 29 metallurgy aim to occupy a design space in temperature capability between Alloy 718 and 30 current powder alloys that are in-service, and show levels of γ' of about 30-44%. The focus 31 in developing these alloys was design for manufacturability. To complement the aerospace 32 developments, a review of work to understand the suitability of candidate alloys for multiple 33 applications in Advanced-Ultra Supercritical (AUSC) power plants has been undertaken by 34 Detrois, Jablonski and Hawk from the National Energy Technology Laboratory. In these 35 power plants, steam temperatures are required to reach 700-760°C. The common thread is 36 to develop alloys that demonstrate a combination of high temperature properties, which are 37 reliant on both the alloy composition and microstructure and can be produced readily at the 38 right price. For the AUSC applications, the emphasis is on high temperature strength, long 39 term creep life, phase stability, oxidation resistance and robust welding for fabrications. 40 Whereas for powder disk rotors in aircraft engines, the priority is enhanced resistance to 41 time dependent crack growth, phase stability and resistance to environmental damage, while 42 extending the current strength levels, which are shown by existing alloys, to higher 43 temperatures.

36 MATERIALS SCIENCE↗

The contribution of lubricant to the formation of particulate matter with reactivity controlled compression ignition in light-duty diesel engines

Reactivity controlled compression ignition (RCCI) has been shown in single- and multi-cylinder engine research to achieve high thermal efficiencies with ultra-low NO X and soot emissions. The nature of the particulate matter (PM) produced by RCCI operation has been shown in recent research to be different than that of conventional diesel combustion and even diesel low-temperature combustion. Previous research has shown that the PM from RCCI operation contains a large amount of organic material that is volatile and semi-volatile. However, it is unclear if the organic compounds are stemming from fuel or lubricant oil. The PM emissions from dual-fuel RCCI were investigated in this study using two engine platforms, with an emphasis on the potential contribution of lubricant. Both engine platforms used the same base General Motors (GM) 1.9-L diesel engine geometry. The first study was conducted on a single-cylinder research engine with primary reference fuels (PRFs), n-heptane, and iso-octane. The second study was conducted on a four-cylinder GM 1.9-L ZDTH engine which was modified with a port fuel injection (PFI) system while maintaining the stock direct injection fuel system. Multi-cylinder RCCI experiments were run with PFI gasoline and direct injection of 2-ethylhexyl nitrate (EHN) mixed with gasoline at 5 % EHN by volume. In addition, comparison cases of conventional diesel combustion (CDC) were performed. Particulate size distributions were measured, and PM filter samples were collected for analysis of lube oil components. Triplicate PM filter samples (i.e., three individual filter samples) for both gas chromatography-mass spectroscopy (GC-MS; organic) analysis and X-ray fluorescence (XRF; metals) were obtained at each operating point and queued for analysis of both organic species and lubricant metals. Here, the results give a clear indication that lubricants do not contribute significantly to the formation of RCCI PM.

33 ADVANCED PROPULSION SYSTEMS↗

Analyses of hot/warm CO2 removal processes for IGCC power plants

Abstract Compared with a pulverized coal power plant, the integrated gasification combined cycle (IGCC) has several advantages, including, among others better environmental performance and low CO 2 capture cost. Hot/warm CO 2 removal from syngas has also been a subject of research due to its potentially higher thermal efficiency. In this study, we proposed a generic adsorption based hot/warm CO 2 removal process for IGCC power plants. Through analyses of the proposed generic process we have demonstrated that higher temperature of the hot/warm CO 2 removal process will results in larger heat of adsorption, which in turns may increase energy consumption of the process. Under most of the operating temperature range, hot/warm CO 2 removal process will lead to more electricity loss compared to the baseline Selexol process. However, if the adsorption step takes place at a temperature close to or higher than the highest steam temperature in steam cycle, our analysis indicates that the process may lead to minimal electricity loss. The study also provided some other insights into the pathways for hot/warm CO 2 removal process to improve its energy performance through process and sorbent designs. Graphical Abstract

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Cast-in-place, ambiently-dried, silica-based, high-temperature insulation

A novel sol-gel chemistry approach was developed to enable the simple integration of a cast-in-place, ambiently-dried insulation into high temperature applications. The insulation was silica based, synthesized using methyltrimethoxysilane (MTMS) as the precursor. MTMS created a unique silica microstructure that was mechanically robust, macroporous, and superhydrophobic. To allow for casting into and around small, orthogonal features, zirconia fibers were added to increase stiffness and minimize contraction that could otherwise cause cracking during drying. Radiative heat transport was reduced by adding titania powder as an opacifier. To assess relevance to high temperature thermoelectric generator technology, a comprehensive set of materials characterizations were conducted. The silica gel was thermally stable, retained superhydrophobicity with a water contact angle > 150° , and showed a high electrical resistance > 1 GΩ, regardless of heating temperature (up to 600 °C in Ar for 4 h). In addition, it exhibited a Young's modulus ~3.7 MPa in room temperature and a low thermal conductivity < 0.08 W/m.K before and after heat treatment. Thus, based on the simplicity of the manufacturing process and optimized material properties, we believe this technology can act as an effective cast-in-place thermal insulation (CTI) for thermoelectric generators and myriad other applications requiring improved thermal efficiency.

36 MATERIALS SCIENCE↗

Four equation k-omega based turbulence model with algebraic flux for supercritical flows

Hydrocarbon and nuclear fuels will contribute substantially to the growing global energy portfolio for some time to come. At the same time atmospheric carbon levels and economic concerns are increasingly shaping the power generation environment. Supercritical fluid technologies are being investigated to address both concerns. For example, direct fired supercritical CO 2 power cycles offer key advantages for carbon capture and thermal efficiency. Additionally, the supercritical water reactor Generation IV nuclear reactor allows higher power densities and more efficient operation than current pressurized or boiling water reactors. As these technologies are developed, a need exists for accurate, yet cost-effective modeling and simulation solutions to assist with design and safety calculations. Supercritical fluid properties are strongly dependent on temperature which results in a number of unique flow features. Among these features are the complex buoyancy and buoyancy-turbulence interaction behaviors exhibited by supercritical flows that are not found in liquid or gas flows. Therefore, standard turbulence models with current model coefficient values are not likely to be applicable to supercritical fluid flows. The subject of this paper is efficient modeling and simulation of supercritical flows to support nascent technologies growing to maturation and operational deployment. We present a framework for developing Reynolds-Averaged Navier-Stokes turbulence models specifically equipped for the challenges of supercritical flows. A novel formulation of the algebraic heat flux model of the buoyancy production of turbulence term is used with a traditional shear stress transport model. To produce a new turbulence model for supercritical channel flows, the empirical coefficients of the resulting four equation model were calculated from data previously published by other authors regarding upward supercritical flow through heated pipes. The presented SST k t - ω t approach was validated against heated tube experiments to show predictive capabilities in moderate flow conditions, where buoyancy effects are important but not dominating of inertial effects.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

End-of-injection fuel dribble of multi-hole diesel injector: Comprehensive investigation of phenomenon and discussion on control strategy

The needle shutdown of fuel injectors leads to an undesired fuel dribble that forms unburned hydrocarbons and decreases the engine thermal efficiency in modern engines. Understanding of the fuel dribbling process is of great importance to establish its minimization strategy for optimal use of conventional fuels. However, the detailed needle dynamics and in- and near-nozzle flow characteristics governing the fuel dribble process have not been thoroughly understood. In this study, the needle dynamics, in- and near-nozzle flow characteristics and fuel dribble of a mini-sac type three-hole diesel injector were investigated using a highspeed X-ray phase-contrast imaging technique at different injection pressures. The results showed that an increase in injection pressure increased the flow evacuation velocity at the needle close that induced a more intense fuel cavitation and air ingestion inside the nozzle. The fuel dribbling process showed a high shot-toshot deviation. A statistical analysis of 50-shot results exhibited two breakup modes of fuel dribble determined by the flow evacuation velocity at the needle close and presence of air ingestion. In the first mode, the fast breakup with a short residence time of fuel dribble occurred. Meanwhile, the dripping of undisturbed liquid column with a long residence time of fuel dribble occurred in the second mode. An increase in injection pressure increased the population of the first mode due to more intense air ingestion that primarily caused by an increase in needle closing speed other than an increase in peak injection velocity. Based on the results, the formation mechanism and control strategies of the fuel dribble from modern diesel injectors were discussed.

Moon, Seoksu↗

Optimal design of microtube recuperators for an indirect supercritical carbon dioxide recompression closed Brayton cycle

This paper presents a baseline design and optimization approach developed in Aspen Custom Modeler (ACM) for microtube shell-and-tube exchangers (MSTEs) used for high- and low-temperature recuperation in a 10 MWe indirect supercritical carbon dioxide (sCO 2 ) recompression closed Brayton cycle (RCBC). The MSTE-type recuperators are designed using one-dimensional models with thermal-hydraulic correlations appropriate for sCO 2 and properties models that capture considerable nonlinear changes in CO 2 properties near the critical and pseudo-critical points. Using the successive quadratic programming (SQP) algorithm in ACM, optimal recuperator designs are obtained for either custom or industry-standard microtubes considering constraints based on current advanced manufacturing techniques. The three decision variables are the number of tubes, tube pitch-to-diameter ratio, and tube diameter. Five different objective functions based on different key design measures are considered: minimization of total heat transfer area, heat exchanger volume, metal weight, thermal residence time, and maximization of compactness. Sensitivities studies indicate the constraint on the maximum number of tubes per shell does affect the number of parallel heat exchanger trains but not the tube selection, total number of tubes, tube length and other key design measures in the final optimal design when considering industry-standard tubes. In this study, the optimally designed high- and low-temperature recuperators have 47,000 3/32 inch tubes and 63,000 1/16 inch tubes, respectively. In addition, sensitivities to the design temperature approach and maximum allowable pressure drop are studied, since these specifications significantly impact the optimal design of the recuperators as well as the thermal efficiency and the economic performance of the entire sCO 2 Brayton cycle.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Techno-economic optimization of shale gas to dimethyl ether production processes via direct and indirect synthesis routes

The shale gas to dimethyl ether process via direct synthesis route with a syngas H2/CO=1 has a higher dimethyl ether yield than that via indirect synthesis route. However, the direct synthesis route involves various energy and capital-intensive processes, such as the complicated dimethyl ether separation process, and the CO2 recycle and comprssion process. In this study, a techno-economic analysis of the shale gas to dimethyl ether process via direct and indirect synthesis routes is performed using Aspen Process Economic Analyzer based on the rigorous process model developed in Aspen Plus. Effects of different CO2 removal technologies and dimethyl ether synthesis technologies from syngas are evaluated. Both, direct and indirect plants are optimized in Aspen Plus equation-oriented environment using the rigorous process models. The effects of key design parameters (i.e. H2/CO in the syngas) as well as investment parameters (i.e. prices of raw materials, products, and utilities, plant scale) on the process economics as been evaluated. The direct dimethyl ether synthesis route processing a syngas with H2/CO =1 and using the Rectisol process for CO2 capture has the highest overall thermal efficiency on the lower heat value basis is found to be much lower than the current U.S. market diesel price indicating the feasibility of the process.

Mevawala, Chirag↗

CoolPINNs: A physics-informed neural network modeling of active cooling in vascular systems

Emerging technologies like hypersonic aircraft, space exploration vehicles, and batteries avail fluid circulation in embedded microvasculatures for efficient thermal regulation. Modeling is vital during the design and operational phases of these engineered systems. However, many challenges exist in developing a modeling framework. What is lacking is an accurate framework that (i) captures sharp jumps in the thermal flux across complex vasculature layouts, (ii) deals with oblique derivatives (involving tangential and normal components), (iii) handles nonlinearity because of radiative heat transfer, (iv) provides a high-speed forecast for real-time monitoring, and (v) facilitates robust inverse modeling. Here, this paper addresses these challenges by availing the power of physics-informed neural networks (PINNs). We develop a fast, reliable, and accurate Scientific Machine Learning (SciML) framework for vascular-based thermal regulation—called CoolPINNs: a PINNs-based modeling framework for active cooling. The proposed mesh-less framework elegantly overcomes all the mentioned challenges. The significance of the reported research is multi-fold. First, the framework is valuable for real-time monitoring of thermal regulatory systems because of rapid forecasting. Second, researchers can address complex thermoregulation designs since the approach is meshless. Finally, the framework facilitates systematic parameter identification and inverse modeling studies, perhaps the most significant utility of the current framework.

97 MATHEMATICS AND COMPUTING↗

Coupled modeling of a directly heated tubular solar receiver for supercritical carbon dioxide Brayton cycle: Optical and thermal-fluid evaluation

In single phase performance and appealing thermo-physical properties supercritical carbon dioxide (s-CO 2 ) make a good heat transfer fluid candidate for concentrating solar power (CSP) technologies. The development of a solar receiver capable of delivering s-CO 2 at outlet temperatures ~973 K is required in order to merge CSP and s-CO 2 Brayton cycle technologies. A coupled optical and thermal-fluid modeling effort for a tubular receiver is undertaken to evaluate the direct tubular s-CO 2 receiver’s thermal performance when exposed to a concentrated solar power input of ~0.3–0.5 MW. Ray tracing, using SolTrace, is performed to determine the heat flux profiles on the receiver and computational fluid dynamics (CFD) determines the thermal performance of the receiver under the specified heating conditions. Moreover, an in-house MATLAB code is developed to couple SolTrace and ANSYS Fluent. CFD modeling is performed using ANSYS Fluent to predict the thermal performance of the receiver by evaluating radiation and convection heat loss mechanisms. Understanding the effects of variation in heliostat aiming strategy and flow configurations on the thermal performance of the receiver was achieved through parametric analyses. Finally, a receiver thermal efficiency ~85% was predicted and the surface temperatures were observed to be within the allowable limit for the materials under consideration.

54 ENVIRONMENTAL SCIENCES↗

Coal-derived conductive pavement for winter de-icing: prototype, modeling, and simulation

Existing pavement de-icing methods result in high installation and maintenance costs, traffic delays, excessive weariness and corrosion, and negative environmental and safety impacts. To overcome these challenges, this paper presents an innovative pathway to designing and constructing smart self-heating pavements using a low-cost coal-char bearing asphalt material. The conductive asphalt incorporates coal char, i.e., a key byproduct of the coal pyrolysis process, into the Stone Mastic Asphalt (SMA) mixture. This asphalt containing coal-derived solid carbon exhibits highly tailorable electrical conductivity, satisfactory mechanical and thermophysical properties, and superior cost-efficiency as compared to other conductive pavement materials. The de-icing performance was also demonstrated by laboratory experiments on a bench-scale prototype. Furthermore, an efficient thermal network model was developed and validated by experiments to investigate the transient thermal behavior and energy performance of the Ohmic heating pavement system. Furthermore, the whole-year energy simulation case studies were conducted on a bridge pavement with an annual energy use of 24.6–1444.8 kWh/m 2 , showcasing its potential in field applications across cool humid, cold humid, and subarctic/arctic climate zones.

42 ENGINEERING↗

Why ionizing radiation enhances surface wettability

Radiation-Induced Surface Activation is an inherent phenomenon where surfaces that are exposed to gamma irradiation are observed to undergo an increase in wettability. This increase in wettability as a result of the ionizing radiation exposure has so far been demonstrated to have a pronounced impact on Leidenfrost temperature and two-phase fluid dynamics. Test results from previous experiments have shown that incorporation of this effect on heat transfer equipment design may increase the thermal-hydraulic margin leading to higher thermal efficiency. However, the mechanism behind the increased wettability is not clearly understood. In the present work, three different materials (Zircaloy-4, 316 stainless steel, and copper) were exposed at two different dose rates with use of two different gamma irradiation facilities. A detailed surface characterization on the post-irradiated samples is carried out to understand the changes in surface chemistry, wettability and surface morphology. It is observed from the experiments that the increase in wettability upon irradiation depended on the total dose and not on the dose rate. Moreover, localized oxidation and porosity induced by radiolysis was seen to be the predominant mechanism behind increased wettability which leads to improved Leidenfrost temperature.

36 MATERIALS SCIENCE↗