Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “test matrix”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

CSPlib: A performance portable parallel software toolkit for analyzing complex kinetic mechanisms

Computational singular perturbation (CSP) is a method to analyze dynamical systems. It targets the decoupling of fast and slow dynamics using an alternate linear expansion of the right-hand side of the governing equations based on eigenanalysis of the associated Jacobian matrix. This representation facilitates diagnostic analysis, detection and control of stiffness, and the development of simplified models. For this work, we have implemented CSP in a C++ open-source library CSPlib using the Kokkos parallel programming model to address portability across diverse heterogeneous computing platforms, i.e., multi/many-core CPUs and GPUs. We describe the CSPlib implementation and present its computational performance across different computing platforms using several test problems. Specifically, we test the CSPlib performance for a constant pressure ignition reactor model on different architectures, including IBM Power 9, Intel Xeon Skylake, and NVIDIA V100 GPU. The size of the chemical kinetic mechanism is varied in these tests. As expected, the Jacobian matrix evaluation, the eigensolution of the Jacobian matrix, and matrix inversion are the most expensive computational tasks. When considering the higher throughput characteristic of GPUs, GPUs performs better for small matrices with higher occupancy rate. CPUs gain more advantages from the higher performance of well-tuned and optimized linear algebra libraries such as OpenBLAS.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS1988

The viscoplastic behavior of SCS6/Ti-15-3 metal matrix composite materials at elevated temperatures

Titanium-based metal matrix composite materials (MMC'S) are being considered for use in the National Aerospace Plane. It is expected that these materials will be subjected to temperatures ranging up to about 820 C (1500 F). The present study was a preliminary investigation intended to quantify the level of viscoplastic behavior exhibited by SCS6/Ti-15-3 MMC's at elevated temperatures. The study consisted of a series of uniaxial creep/creep recovery tests. These tests were conducted in air at a temperature of 535 C (1000 F). Three distinct types of specimens were tested: Ti-15-3 heat matrix specimens (O2/plus or minus 45) sub s composite specimens, and (90 sub 2/plus or minus 45) sub s composite specimens. Tensile loads were applied to the specimens using a lever-arm creep frame equipped with a high temperature furnace. Specimen creep stains were monitored using an LVDT-based extensometer.

Tuttle, Mark E.↗
NASA NTRS2015

Marking Tests to Certify Part Identification Processes for Use in Low Earth Orbit

The primary purpose for the MISSE marking tests was to define Data Matrix symbol marking processes that will remain readable after exposure to Low Earth Orbit environments. A wide range of different Data Matrix symbol marking processes and materials, including some still under development, were evaluated. The samples flown on MISSE 1 and 2 were in orbit for 3 years and 348 days, MISSE 3 and 4 were in orbit for 1 year and 15 days, MISSE 6 was in orbit for 1 year and 130 days, and MISSE 8 was in orbit for 2 years and 55 days. The initial MISSE marking tests clearly reflected that intrusive marking processes can be successfully used for this purpose. All of the intrusive marking processes tested exceeded program expectations and met 100 percent of the principle investigators objectives. However, subsequent tests demonstrated that some additive marking processes will also satisfy the requirements. This was an unexpected result.

Roxby, D. L.↗
DOE OSTI2023

Multi-Scale Characterization of Porosity and Cracks in Silicon Carbide Cladding after Transient Reactor Test Facility Irradiation

Silicon carbide (SiC) ceramic matrix composite (CMC) cladding is currently being pursued as one of the leading candidates for accident-tolerant fuel (ATF) cladding for light water reactor applications. The morphology of fabrication defects, including the size and shape of voids, is one of the key challenges that impacts cladding performance and guarantees reactor safety. Therefore, quantification of defects’ size, location, distribution, and leak paths is critical to determining SiC CMC in-core performance. This research aims to provide quantitative insight into the defect’s distribution under multi-scale characterization at different length scales before and after different Transient Reactor Test Facility (TREAT) irradiation tests. A non-destructive multi-scale evaluation of irradiated SiC will help to assess critical microstructural defects from production and/or experimental testing to better understand and predict overall cladding performance. X-ray computed tomography (XCT), a non-destructive, data-rich characterization technique, is combined with lower length scale electronic microscopic characterization, which provides microscale morphology and structural characterization. This paper discusses a fully automatic workflow to detect and analyze SiC-SiC defects using image processing techniques on 3D X-ray images. Following the XCT data analysis, advanced characterizations from focused ion beam (FIB) and transmission electron microscopy (TEM) were conducted to verify the findings from the XCT data, especially quantitative results from local nano-scale TEM 3D tomography data, which were utilized to complement the 3D XCT results. In this work, three SiC samples (two irradiated and one unirradiated) provided by General Atomics are investigated. The irradiated samples were irradiated in a way that was expected to induce cracking, and indeed, the automated workflow developed in this work was able to successfully identify and characterize the defects formation in the irradiated samples while detecting no observed cracking in the unirradiated sample. These results demonstrate the value of automated XCT tools to better understand the damage and damage propagation in SiC-SiC structures for nuclear applications.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2022

Quantum Krylov subspace algorithms for ground- and excited-state energy estimation

Quantum Krylov subspace diagonalization (QKSD) algorithms provide a low-cost alternative to the conventional quantum phase estimation algorithm for estimating the ground- and excited-state energies of a quantum many-body system. While QKSD algorithms typically rely on using the Hadamard test for estimating Krylov subspace matrix elements of the form $\langle \phi_i|e^{-\widehat{H}τ}|\phi_j\rangle$, the associated quantum circuits require an ancilla qubit with controlled multiqubit gates that can be quite costly for near-term quantum hardware. In this paper, we show that a wide class of Hamiltonians relevant to condensed-matter physics and quantum chemistry contain symmetries that can be exploited to avoid the use of the Hadamard test. We propose a multifidelity estimation protocol that can be used to compute such quantities, showing that our approach, when combined with efficient single-fidelity estimation protocols, provides a substantial reduction in circuit depth. In addition, here we develop a unified theory of quantum Krylov subspace algorithms and present three quantum-classical algorithms for the ground- and excited-state energy estimation problems, where each algorithm provides various advantages and disadvantages in terms of total number of calls to the quantum computer, gate depth, classical complexity, and stability of the generalized eigenvalue problem within the Krylov subspace.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

Blast Effects on Buildings (Final Report)

Lawrence Livermore National Laboratory (LLNL) has conservatively reduced the explosive safety standards suggested by the Small Quantities in Research Laboratories (SQRL) program testing by 60%. For this reason, further research into the detailed effects of small amounts of explosives in typically constructed rooms is needed in order to improve their factor of safety. The team was tasked with designing an experiment to investigate the effect of different variables on drywall under explosive blasts. In order to meet this objective, the team conducted a comprehensive literature review to gain an understanding of industry-standard construction practices and review previous tests conducted by the Army corp of engineers. Since the team used PBXN-5 rather than C4, as in SQRL, an initial shot was conducted to compare damage levels. From those results and the physical constraints of the testing chamber, the team redesigned multiple single-panel drywall frames to capture the entirety of the incurred damage. Proposed designs were narrowed down using a decision matrix. From the study of previous tests and literature review, variables were chosen that the team hypothesized to have an impact on drywall strength. The variables that were tested were chosen from the results of that work and specific variables the sponsor was interested in, and they were paint, humidity/moisture content, and explosive positioning relative to the studs. Detailed plans were made for each variable according to what conditions the team wanted to investigate. For humidity, this involved testing low, ambient, and high conditions by treating the panels in a chamber. Preliminary shots were performed to test the structural integrity of the frame and streamline the test diagnostics which involved a high-speed camera placed behind the drywall, outside of the chamber, and a pressure probe placed behind the drywall, inside the chamber. Once the instrumentation, diagnostics, and frame design were finalized, a quantitative damage criteria matrix was created to categorize the results of the main shot series. In conjunction with evidence from the high-speed video, the achieved damage levels indicate that high moisture content drywall is better able to withstand explosive blasts. Larger stud damage and lower drywall damage occurred when the explosive was located directly in front of a stud. Paint had no noticeable impact on strength. Ultimately, the team conducted a total of 17 tests, leaving the door open for future in-depth research into the impact of humidity.

36 MATERIALS SCIENCE↗
NASA NTRS1994

Sapphire reinforced alumina matrix composites

Unidirectionally reinforced A1203 matrix composites have been fabricated by hot pressing. Approximately 30 volume % of either coated or uncoated sapphire fiber was used as reinforcement. Unstabilized ZrO2 was applied as the fiber coating. Composite mechanical behavior was analyzed both after fabrication and after additional heat treatment. The results of composite tensile tests were correlated with fiber-matrix interfacial shear strengths determined from fiber push-out tests. Substantially higher strength and greater fiber pull-out were observed for the coated fiber composites for all processing conditions studied. The coated fiber composites retained up to 95% and 87% of their as-fabricated strength when heat treated at 14000C for 8 or 24 hours, respectively. Electron microscopy analysis of the fracture surfaces revealed extensive fiber pull-out both before and after heat treatment.

Jaskowiak, Martha H.↗
NASA NTRS1972

Nozzle exhaust plume backscatter experiment using the JPL Molsink facility

Qualitative tests were made by injecting water through a rocket nozzle wall, and the droplet trajectories were observed photographically. These tests were conducted for nozzles in which boundary layer flow is significant. The tests indicated that both gases and particulate matter will be found in the region outside of the plume boundaries, and can be calculated using current analytical techniques. A test program is being conducted to measure the distribution of exhaust gases from small nozzles using an electron beam/photomultiplier system and a matrix of quartz crystal microbalances. Calibration tests, using simulated hydrazine exhaust product gas mixtures, were also conducted. The test program and results of the pumping calibration tests with hydrazine (simulated hydrazine exhaust products) are reported.

Simon, W.↗
NASA NTRS2019

Reexamination of the Edge Crack Torsion Test for Determining the Mode III Delamination Toughness of Laminated Composites

The edge crack torsion (ECT) test is reexamined to address two primary concerns with this method. The first of these relates to inconsistencies in the data reduction procedure that was originally proposed and is most commonly used to compute the mode III interlaminar fracture toughness, G(sub IIIc), from the experimental data. The second relates to the observation that plies neighboring the preimplanted insert in the standard ECT layup are unable to contain initiation and growth of intralaminar cracks, and that growth of these cracks contributes to errors in the apparent values of G(sub IIIc). To address these issues, an alternative data reduction technique, which uses a polynomial expression to represent the ECT specimen’s compliance versus crack length relation, is proposed. The accuracy and potential drawbacks of this expression are investigated using FE simulations. Next, seven groups of ECT specimens are fabricated and tested. Each of these groups contains specimens with preimplanted inserts that are bounded by plies at different +q and -q orientations. The seven groups consist of values of q that vary from 0° to 90° in 15° increments. Tests on these specimens show that intralaminar cracking occurs in specimens from all batches except those for which q equals 15° or 30°. However, values of G(sub IIIc) measured using specimens with these two ply orientations were not equal and, for q = 30°, the values of G(sub IIIc) that were obtained were not completely independent of initial starter crack length. Potential issues accounting for these observations and other challenges associated with measuring G(sub IIIc) using the ECT test are discussed.

Polymer matrix composites↗
NASA NTRS1993

An analysis of fiber-matrix interface failure stresses for a range of ply stress states

A graphite/bismaleimide laminate was prepared without the usual fiber treatment and was tested over a wide range of stress states to measure its ply cracking strength. These tests were conducted using off-axis flexure specimens and produced fiber-matrix interface failure data over a correspondingly wide range of interface stress states. The absence of fiber treatment, weakened the fiber-matrix interfaces and allowed these tests to be conducted at load levels that did not yield the matrix. An elastic micromechanics computer code was used to calculate the fiber-matrix interface stresses at failure. Two different fiber-array models (square and diamond) were used in these calculations to analyze the effects of fiber arrangement as well as stress state on the critical interface stresses at failure. This study showed that both fiber-array models were needed to analyze interface stresses over the range of stress states. A linear equation provided a close fit to these critical stress combinations and, thereby, provided a fiber-matrix interface failure criterion. These results suggest that prediction procedures for laminate ply cracking can be based on micromechanics stress analyses and appropriate fiber-matrix interface failure criteria. However, typical structural laminates may require elastoplastic stress analysis procedures that account for matrix yielding, especially for shear-dominated ply stress states.

Crews, J. H.↗
DOE OSTI2020

On the statistical treatment of the Cabibbo angle anomaly

We point out that testing the equality of the Cabibbo angle as extracted from $\Gamma(K\rightarrow \pi l\nu)$, the ratio $\Gamma(K\rightarrow l\nu)/\Gamma(\pi\rightarrow l\nu)$ and nuclear $\beta$ decays is not identical to a test of first row unitarity of the Cabibbo-Kobayashi-Maskawa (CKM) matrix. The reason is that a CKM unitarity test involves only two parameters, while the degrees of freedom for the assessment of the goodness-of-fit of the universality of the Cabibbo angle entailed by the Standard Model (SM) is equal to the number of measurements minus one. Beyond the SM all different processes could in principle give different Cabibbo angles. Consequently, the difference between the two tests becomes relevant starting from three observables giving results for the Cabibbo angle that are in tension with each other. With current data, depending on the treatment of the nuclear $\beta$ decays, we find that New Physics is favored over the SM at $5.1\,\sigma$ or $3.6\,\sigma$ while CKM unitarity is rejected at $4.8\sigma$ or $3.0\sigma$, respectively. We argue that the best method to test the SM is to test the equality of the Cabibbo angle, because CKM unitarity is only one aspect of the SM.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
NASA NTRS1992

A static investigation of the thrust vectoring system of the F/A-18 high-alpha research vehicle

A static (wind-off) test was conducted in the static test facility of the Langley 16-foot Transonic Tunnel to evaluate the vectoring capability and isolated nozzle performance of the proposed thrust vectoring system of the F/A-18 high alpha research vehicle (HARV). The thrust vectoring system consisted of three asymmetrically spaced vanes installed externally on a single test nozzle. Two nozzle configurations were tested: A maximum afterburner-power nozzle and a military-power nozzle. Vane size and vane actuation geometry were investigated, and an extensive matrix of vane deflection angles was tested. The nozzle pressure ratios ranged from two to six. The results indicate that the three vane system can successfully generate multiaxis (pitch and yaw) thrust vectoring. However, large resultant vector angles incurred large thrust losses. Resultant vector angles were always lower than the vane deflection angles. The maximum thrust vectoring angles achieved for the military-power nozzle were larger than the angles achieved for the maximum afterburner-power nozzle.

Mason, Mary L.↗
NASA NTRSDate not supplied

Experimental Calibration of Flow Rule Coefficients for LS-Dyna Mat_213

Composite materials have become a popular choice in aerospace engineering applications due to their low weight, high specific stiffness, high specific energy absorption, and economic synthesis. As use of composite materials has proliferated, the need for accurate simulation under extreme loading conditions is of increasing importance. *MAT_213 is a tabulated plasticity and damage material model in LS-DYNA designed for such use cases. To account for the nonlinear material response, a plasticity algorithm is used, which employs a non-associative flow rule with coefficients requiring experimental calibration. This work outlines an experimental methodology for calibrating these coefficients using the macroscopic stress-strain response and microscopic in-plane strain measurements from coupon scale experiments. The model material used for the development and demonstration of this methodology is a plain weave woven fabric with T300 carbon fiber tows in the warp direction and Kevlar© 49 fiber tows in the weft direction, and an Epon© 828/Epikure© 3223 thermoset epoxy matrix. Coupon-scale tensile testing performed at multiple fiber angles (carbon fibers oriented 0º, 22.5º, 45º, 67.5º, and 90º relative to the loading axis) provides data for multiple calibration processes. The measured plastic strain increments in the principal material coordinate are used to set limits for ratios between flow rule coefficients. The identified ranges are used to bound the search for a set of coefficients, leading to convergence of different coupon responses in the effective stress – effective plastic strain space. Flow rule coefficients found by this methodology are then used as (i) input for LS-DYNA simulations of uniaxial tension coupon tests at varying fiber angles, and (ii) comparison of predicted values for the plastic Poisson’s ratio in global coordinates with the experimentally measured one for all off-axis orientations. These results are quantitatively and qualitatively compared to macroscopic stress-strain curves and experimental strain components. The conformity of the experimentally measured quantities with those derived from the simulations provide a means for assessing the quality of calibrated coefficients.

Polymer Matrix Composites↗
NASA NTRS2019

Materials and Processes for New Propulsion Systems with Reduced Environmental Impact

Aeronautics research at NASA Glenn Research Center includes development, characterization and modeling of high temperature, lightweight materials and fabrication processes for aircraft propulsion systems with increased efficiency and reduced emissions, fuel burn and noise. Current propulsion materials research includes Ceramic Matrix Composites and Environmental Barrier Coatings, Polymer Matrix Composites and Additive Manufacturing processes. This presentation will summarize recent progress and plans in these areas. Ceramic Matrix Composites for Turbine Components: As part of NASA's Aeronautics research, Glenn Research Center has developed Ceramic Matrix Composites for 2700 degrees Fahrenheit turbine engine applications in the next generation of ultra-efficient aircraft. In this presentation, the development of advanced fiber and matrix constituents that enabled this advancement will be reviewed, and characterization of the resulting improvements in mechanical properties and durability will be summarized. Progress toward the development and validation of models predicting the effects of the engine environment on durability of Ceramic Matrix Composites and Environmental Barrier Coatings will be summarized. Progress and plans for collaborative research with industry and other government agencies will be reviewed. Polymer Matrix Composites for Powertrain and Impact Protection: A lightweight, hybrid polymer matrix composite/steel gear concept for rotorcraft power transmission applications was evaluated at realistic speed, torque, and power conditions. Dynamic testing was performed at 5000 horsepower and 5400 revolutions per minute with no performance degradation. Test results demonstrated the potential of hybrid composite / metal gears to reduce gear weight by approximately 15 percent, enabling the implementation of multi-speed drive systems, which would otherwise have a weight penalty, for increased speed and efficiency. Results of post-test inspection and endurance tests will be presented. Separately, ballistic impact tests demonstrated improved damage tolerance in polymer matrix composites by incorporating lightweight, thermoplastic veil materials between selected composite plies during the composite fabrication process. Results of impact tests and post-test inspection will be presented. Additive Manufacturing for Electric Propulsion: Additive Manufacturing processes offer the potential to fabricate new, high power density electric motor designs with complex geometries, multi-material components and optimally designed components that would not be feasible with traditional manufacturing processes. High performance stator components using advanced 3-phase conductive coils were fabricated using direct printing with optimized silver pastes. Additional additive manufacturing methods are being used to fabricate rotors and motor housing components. Systems studies show that the higher performance and lower weight motors offer improved energy efficiency and reduced emissions. Improvements to motor performance resulting from optimized materials and component designs will be presented.

Additive Manufacturing↗
NASA NTRS2000

Intermediate Temperature Stress Rupture of Woven SiC Fiber, BN Interphase, SiC Matrix Composites in Air

Tensile stress-rupture experiments were performed on woven Hi-Nicalon reinforced SiC matrix composites with BN interphases in air. Modal acoustic emission (AE) was used to monitor the damage accumulation in the composites during the tests and microstructural analysis was performed to determine the amount of matrix cracking that occurred for each sample. Fiber fractograph), was also performed for individual fiber failures at the specimen fracture surface to determine the strengths at which fibers failed. The rupture strengths were significantly worse than what would have been expected front the inherent degradation of the fibers themselves when subjected to similar rupture conditions. At higher applied stresses the rate of rupture "?as larger than at lower applied stresses. It was observed that the change in rupture rate corresponded to the onset of through-thickness cracking in the composites themselves. The primary cause of the sen,ere degradation was the ease with which fibers would bond to one another at their closest separation distances, less than 100 nanometers, when exposed to the environment. The near fiber-to-fiber contact in the woven tows enabled premature fiber failure over large areas of matrix cracks due to the stress-concentrations created b), fibers bonded to one another after one or a few fibers fail. i.e. the loss of global load sharing. An@, improvement in fiber-to-fiber separation of this composite system should result in improved stress- rupture properties. A model was den,eloped in order to predict the rupture life-time for these composites based on the probabilistic nature of indin,idual fiber failure at temperature. the matrix cracking state during the rupture test, and the rate of oxidation into a matrix crack. Also incorporated into the model were estimates of the stress-concentration that would occur between the outer rim of fibers in a load-bearing bundle and the unbridged region of a matrix crack after Xia et al. For the lower stresses, this source of stress-concentration was the likely cause for initial fiber failure that would trigger catastrophic failure of the composite.

Morscher, Gregory N.↗
NASA NTRS1996

Structures Division 1994 Annual Report

The NASA Lewis Research Center Structures Division is an international leader and pioneer in developing new structural analysis, life prediction, and failure analysis related to rotating machinery and more specifically to hot section components in air-breathing aircraft engines and spacecraft propulsion systems. The research consists of both deterministic and probabilistic methodology. Studies include, but are not limited to, high-cycle and low-cycle fatigue as well as material creep. Studies of structural failure are at both the micro- and macrolevels. Nondestructive evaluation methods related to structural reliability are developed, applied, and evaluated. Materials from which structural components are made, studied, and tested are monolithics and metal-matrix, polymer-matrix, and ceramic-matrix composites. Aeroelastic models are developed and used to determine the cyclic loading and life of fan and turbine blades. Life models are developed and tested for bearings, seals, and other mechanical components, such as magnetic suspensions. Results of these studies are published in NASA technical papers and reference publication as well as in technical society journal articles. The results of the work of the Structures Division and the bibliography of its publications for calendar year 1994 are presented.

Source record↗