Results for “surface reactor” — Page 38

NASA NTRS1995

High efficient radiation stable AlGaAs/GaAs solar cells with internal Bragg reflector

An investigation of solar cells based on AlGaAs/GaAs heterostructures with an internal Bragg reflector as the back-surface reflector is presented. The Bragg reflector is grown by low pressure metalorganic chemical vapor deposition on n-GaAs substrates in a horizontal resistively heated reactor. The Bragg reflector with its maximum reflectance centered at a wavelength of 860 nm consists of 12 pairs of AlAs/GaAs layers. The resulting Bragg reflector has a thickness of 0.072 micrometers for AlAs and 0.059 micrometers for GaAs. The multi-layered quasi-dielectric stack selectively reflects weakly absorbed photons with energies near to the GaAs band gap for a second pass through the photoactive region, thus increasing the photocurrent. The use of the Bragg reflector allows the external quantum efficiency to be increased in the long wavelength of the spectrum. The use of the Bragg reflector and an antireflective coating and prismatic cover allowed an efficiency of 23.4 percent to be obtained.

Andreev, V. M.↗

NASA NTRS2013

Trace Contaminant Control: An In-Depth Study of a Silica-Titania Composite for Photocatalytic Remediation of Closed-Environment Habitat Air

This collection of studies focuses on a PCO system for the oxidation of a model compound, ethanol, using an adsorption-enhanced silica-TiO2 composite (STC) as the photocatalyst; studies are aimed at addressing the optimization of various parameters including light source, humidity, temperature, and possible poisoning events for use as part of a system for gaseous trace-contaminant control system in closed-environment habitats. The first goal focused on distinguishing the effect of photon flux (i.e., photons per unit time reaching a surface) from that of photon energy (i.e., wavelength) of a photon source on the PCO of ethanol. Experiments were conducted in a bench-scale annular reactor packed with STC pellets and irradiated with either a UV-A fluorescent black light blue lamp O max=365 nm) at its maximum light intensity or a UV-C germicidal lamp O. max=254 nm) at three levels of light intensity. The STC-catalyzed oxidation of ethanol was found to follow zero-order kinetics with respect to CO2 production, regardless of the photon source. Increased photon flux led to increased EtOH removal, mineralization, and oxidation rate accompanied by lower intermediate concentration in the effluent. The oxidation rate was higher in the reactor irradiated by UV-C than by UV-A (38.4 vs. 31.9 nM s-1 ) at the same photon flux, with similar trends for mineralization (53.9 vs. 43.4%) and reaction quantum efficiency (i.e., photonic efficiency, 63.3 vs. 50.1 nmol C02 ~mol photons-1 ). UV-C irradiation also led to decreased intermediate concentration in the effluent compared to UV -A irradiation. These results demonstrated that STC-catalyzed oxidation is enhanced by both increased photon flux and photon energy. The effect of temperature and relative humidity on the STC-catalyzed degradation of ethanol was also determined using the UV-A light source at its maximum intensity.

Coutts, Janelle L.↗

NASA NTRS2015

Benefits of Microalgae for Human Space Exploration

Algae have long been known to offer a number of benefits to support long duration human space exploration. Algae contain proteins, essential amino acids, vitamins, and lipids needed for human consumption, and can be produced using waste streams, while consuming carbon dioxide, and producing oxygen. In comparison with higher plants, algae have higher growth rates, fewer environmental requirements, produce far less "waste" tissue, and are resistant to digestion and/or biodegradation. As an additional benefit, algae produce many components (fatty acids, H2, etc.) which are useful as biofuels. On Earth, micro-algae survive in many harsh environments including low humidity, extremes in temperature, pH, and as well as high salinity and solar radiation. Algae have been shown to survive inmicro-gravity, and can adapt to high and low light intensity while retaining their ability to perform nitrogen fixation and photosynthesis. Studies have demonstrated that some algae are resistant to the space radiation environment, including solar ultraviolet radiation. It remains to be experimentally demonstrated, however, that an algal-based system could fulfil the requirements for a space-based Bioregenerative Life Support System (BLSS) under comparable spaceflight power, mass, and environmental constraints. Two specific challenges facing algae cultivation in space are that (i) conventional growth platforms require large masses of water, which in turn require a large amount of propulsion fuel, and (ii) most nutrient delivery mechanisms (predominantly bubbling) are dependent on gravity. To address these challenges, we have constructed a low water biofilm based bioreactor whose operation is enabled by capillary forces. Preliminary characterization of this Surface Adhering BioReactor (SABR) suggests that it can serve as a platform for cultivating algae in space which requires about 10 times less mass than conventional reactors without sacrificing growth rate. Further work is necessary to compare the performance of microalgae-based systems, including SABR, with systems based on higher plants, as well as conventional physicochemical-based systems. Ongoing and future work in our laboratory is therefore directed determining the feasibility of using algae as a component of a BLSS in space.

Algae↗

NASA NTRS2023

Galvanic Protected Anode Materials for Molten Regolith Electrolysis

This effort aimed to explore the use of refractory alloys as long-lifetime electrode materials for use in a molten regolith electrolysis (MRE) reactor, a technology that can produce oxygen (O2) from regolith. To find a material capable of withstanding the high temperatures and corrosive nature of molten regolith, first-principles thermodynamic calculations were performed on platinum group metals in the presence of iron (Fe) and silicon (Si) to determine favorable compositions for resisting unwanted secondary phases that could form on the surface of the material. As a result of these first-principles calculations, the kinetic properties of elements such as aluminum (Al), Fe, and Si can be more easily derived, which would provide insight into the longevity of such a material when used in an MRE reactor. The effort funded by this CIF project mapped the entire phase diagram of platinum group metals, which is beneficial not only to MRE where high temperatures and molten material are present, but also aerospace applications like turbine materials, terrestrial metal processing techniques, and energy storage applications. This project narrowed a broad spectrum of refractory metals down to a small list of alloys that would be able to survive not only the high temperatures of an MRE reactor, but also the thermodynamic forces that would cause inferior alloys to form secondary phases, which would ultimately consume the electrodes of the reactor. This research needs to be followed up with experimental demonstrations of these alloys in an MRE environment.

Kevin Grossman↗

DOE OSTI2020

Microstructure Experiments-Enabled MARMOT Simulations of SiC/SiC-based Accident Tolerant Nuclear Fuel System

We have undertaken an experimental-computational project that addresses a few key technology gaps associated with the use of SiC/SiC composites for light water reactor fuel cladding. Two principal endeavors in this project are to assess the irradiation-induced microstructural changes and swelling in SiC/SiC composites, and to characterize and model the porous oxide surface layer (when exposed to steam) along SiC recession that is detrimental to the clad integrity under accident conditions. The project tasks are: (i) ion irradiation and characterization (University of Tennessee, Knoxville), (ii) mechanical tests and analysis (University of South Carolina), (iii) steam exposure tests (Oak Ridge National Laboratory), (iv) electron microscopy and spectroscopic characterization (NC State University), (v) x-ray microscopy and reconstruction (University of South Carolina and NC State University), (vi) phase field modeling and simulations (NC State University and Idaho National Laboratory). The effects of 10 MeV Au ion irradiation at 350°C on the microstructure evolution in SiC/SiC composites are investigated at doses up to 400 displacements per atom (dpa) at the University of Tennessee, Knoxville. Atomic force microscopy and optical profilometry reveal irradiation induced axial and radial shrinkage of the fibers for doses greater than 10 dpa. Based on detailed electron microscopy characterization, the primary cause of the fiber shrinkage is attributed to irradiation-induced loss of carbon packets. Additionally, the multilayer PyC interface is observed to portray high resistance to irradiation damage. The mechanical response and failure mechanisms of un-irradiated samples is also assessed through loading tests and X-ray imaging at the University of South Carolina. Steam exposure tests are performed at the Oak Ridge National Laboratory in a facility that represents a reactor pressure vessel under a loss-of-coolant-accident scenario. The samples that are analyzed methodically in this report are tested for 32/31 hours at 1200°C with a velocity of 0.25 cm/s for the pressures: 0.1 MPa, 0.45 MPa, 0.92 MPa and 1.38 MPa. Scanning/transmission electron microscopy analysis conducted at the NC State University (NCSU) shows that the oxide layer thickness increases with the steam pressure. While the oxide layer is crystalline (α- cristobalite) for the pressures 0.45 MPa, 0.92 MPa and 1.38 MPa, the layer is amorphous at 0.1 MPa. Results from Raman spectroscopy have also confirmed the formation of α-cristobalite phase of SiO₂. The abrupt increase in the integrated Raman intensity ratio between steam pressures 0.1 and 0.45 MPa suggests the onset of accelerated crystallization. Non-destructive three dimensional X-ray microscopy/tomography (XCT) and computational image processing techniques are employed by the University of South Carolina to probe the porous oxidation features on SiC samples at varying pressures. Interestingly, most pores are observed to be located away from the surface as well as the oxide-SiC interface. The average oxide layer thickness assessed from the XCT analysis is seen to be in excellent agreement with the values determined through scanning electron microscopy analysis for the highest pressures where the oxide layer is relatively more uniform. A phase-field model developed by the NC State University and Idaho National Laboratory for simulating oxidation of SiC by steam captures the paralinear kinetics of SiC oxidation with a high degree of fidelity. Results from quasi-one-dimensional and two dimensional simulations show that the pores with oxidizing species lead to a higher volatilization rate. These simulations indicate that the enhanced apparent volatilization rates at higher pressures observed in experiments can be rationalized by the increased volatilization from the pores. The project team has also successfully developed the capability to import images from experiments for realistic evolution of the oxidizing microstructure.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

Boiling Transitions During Droplet Contact on Superheated Nano/Micro-Structured Surfaces

Manipulating surface topography is one of the most promising strategies for increasing the efficiency of numerous industrial processes involving droplet contact with superheated surfaces. In such scenarios, the droplets may immediately boil upon contact, splash and boil, or could levitate on their own vapor in the Leidenfrost state. In this work we report the outcomes of water droplets coming in gentle contact with designed nano/micro-textured surfaces at a wide range of temperatures as observed using high-speed optical and X-ray imaging. Further, we report a paradoxical increase in the Leidenfrost temperature ($T_{\text{LFP}}$) as the texture spacing is reduced below a critical value (~10 μm) that represents a minima in $T_{\text{LFP}}$. Although droplets on such textured solids appear to boil upon contact, our studies suggest that their behavior is dominated by hydrodynamic instabilities implying that the increase in $T_{\text{LFP}}$ may not necessarily lead to enhanced heat transfer. On such surfaces, the droplets display a new regime characterized by splashing accompanied by a vapor jet penetrating through the droplets before they transition to the Leidenfrost state. We provide a comprehensive map of boiling behavior of droplets over a wide range of texture spacings that may have significant implications towards applications such as electronics cooling, spray cooling, nuclear reactor safety and containment of fire calamities.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Reactor wall effects in Si–Cl 2 –Ar atomic layer etching

This work complements our previous manuscript [J. Vac. Sci. Technol. A41, 062602 (2023)] where predictions from molecular dynamics (MD) simulations of silicon–chlorine–argon (Si–Cl 2 –Ar) atomic layer etching (ALE) are compared to experiments. When etch product distributions for atomic chlorine (Cl) and silicon chlorides were initially compared to optical emission spectroscopy (OES) signals, it appeared that there was a discrepancy between the MD predictions and experimental results at higher ion fluences. Experiments showed a relatively long period of nearly constant Cl-containing etch products released from the ion-bombarded surface (referred to as the “plateau”) but this effect was not observed in MD simulations. In this report, we demonstrate that the “plateau” observed in the OES signals is most likely due to the desorption of Cl-containing etch products from the walls of the reactor and subsequent adsorption on the Si substrate. Experiments varying the gas residence time in the chamber while keeping incoming gas concentrations and pressure constant support this interpretation. We also conducted experiments with an additional Ar-only flow in the chamber to reduce the concentration of Cl-containing species on the chamber walls. For both sets of flow modification experiments, we observe results consistent with the hypothesis that Cl-containing species desorbing from chamber walls are a significant cause of the observed discrepancy between MD predictions and experimental observations. If the measured OES signals are corrected for this “additional” source of Cl-containing species at the surface, the MD predictions and measured OES signals are in excellent agreement. This further supports the predictive capability of MD simulations to accurately capture the relevant physical and chemical processes in plasma-assisted ALE processes. We provide an order of magnitude estimate of the required density of Cl-containing species that would account for the additional etch products observed. Finally, we discuss the implications of this effect on ALE in plasma nanofabrication.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2026

In-Situ TEM Molten Salt Corrosion

Molten salt reactors (MSRs) offer a compelling pathway for next-generation nuclear energy, with advantages in thermal efficiency, inherent safety, and flexible fuel management. Yet, halide-based molten salts introduce significant materials challenges, particularly alloy corrosion. Alloy performance in these environments ultimately depends on understanding how corrosion initiates and progresses at the nanoscale, however most existing models rely on post-exposure characterization, leaving degradation mechanisms largely inferred rather than directly observed. NiCr alloys have garnered interest in MSRs applications as the Ni-based matrix provides strength and creep resistance, while Cr content offers oxidation resistance in air. However, NiCr corrosion resistance in chloride salts has proven poor due to preferential chromium dissolution, the formation of Cr-depleted pathways, and grain-boundary attack. This work aims to directly visualize corrosion of Ni-20Cr exposed to LiCl-KCl using in-situ Transmission Electron Microscopy (TEM) to capture real-time microstructural evolution during corrosion. Experiments will be performed at ~800 °C under controlled pressure conditions while utilizing Energy-Dispersive X-ray Spectroscopy (EDS) to analyze elemental redistribution. Observation of chromium depletion fronts, associated surface restructuring, and localized chloride enrichment are expected. Ultimately, this study is expected to provide a link between microscale processes and the macroscopic degradation behaviors relevant to MSR operation in advanced reactor environments. Simultaneously, this approach enables future in-situ investigations regarding alloy composition, salt chemistry, and their influence on corrosion pathways and long-term stability.?

36 - MATERIALS SCIENCE↗

DOE OSTI2022

Infiltration of molten fluoride salts in graphite: Phenomenology and engineering considerations for reactor operations and waste disposal

The possibility and consequences of salt-infiltration in graphite must be evaluated for graphite used in molten salt reactors (MSRs) and fluoride-salt-cooled high-temperature reactors (FHRs), which can be subjected to salt pressures as high as 500 kPa. The volume of graphite porosity infiltrated by salt can be measured by direct infiltration and it can be predicted from the graphite pore size distribution, the surface tension of the salt, and the contact angle between the graphite and the salt. While these three properties are believed to be insensitive to irradiation, the former can be impacted by chronic or acute oxidation, and the latter two are highly sensitive to the chemistry of the salt and to events such as air ingress. For MSRs, predictions based on nominal properties of salt and graphite reveal that few graphite grades would satisfy the 4 vol% limit set in the Molten Salt Reactor Experiment, and even fewer would satisfy the 0.5 vol% design target. For FHRs, infiltration limits have not been defined and depend on the effect of infiltration on graphite properties, which are discussed. A hypothesis is presented for properties that may be impacted by infiltration and for which future studies are needed.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Investigation of the Mechanisms Underpinning Plasma-Catalyst Interaction for the Conversion of Methane to Oxygenates

Plasma catalysis is a promising approach to further enhance the conversion of methane into value-added products such as methanol. In this work, the mechanisms enabling the conversion of methane to CO, CO 2 and methanol enabled by plasma-enhanced catalysis were investigated. A catalyst reactor was incorporated downstream of the plasma jet to enable the separation between plasma generation and the catalyst bed. An enhancement in CH 3 OH and CO 2 production was observed for the shortest distance between the plasma and catalyst compared to the plasma-only case. Plasma-enabled gas heating was shown not to be responsible for the observed synergy while a gas temperature increase as low as 30-40 K significantly impacted desorption rates of CH 3 OH/C 2 H 5 OH on alumina particles. Correlations between molecular beam mass spectrometry (MBMS) measurements at the inlet and outlet of the catalytic reactor suggest that the observed synergistic effect was caused by radical species most likely the CH 3 O 2 radical. As a result, this study shows that surface reactions induced by radicals such as alkylperoxy radicals might play an important role in surface reactions in plasma-catalysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

Microscopic analysis of irradiated UN–Mo–W for space nuclear propulsion

Nuclear propulsion is an effective method of providing thrust in deep space, allowing for shorter mission duration for long-term surface missions to Mars. The fuel for nuclear propulsion systems must exhibit superior mechanical and thermal properties, to decrease the possibility of fuel failure and to increase reactor efficiency. Here, the objective of the Sirius project is to fabricate and irradiate cermet fuels at the Idaho National Laboratory Transient Reactor Facility to determine the properties of the fuel after irradiation at prototypical nuclear propulsion start-up conditions. The Sirius project featured 3 test capsules, Sirius-1 featured uranium nitride fuel dispersed in a matrix of tungsten and rhenium, while Sirius-2A and -2B featured uranium nitride-molybdenum-tungsten fuel (UN-Mo-W). The fuel samples from the Sirius-2A and -2B capsules were examined after irradiation using optical microscopy, scanning electron microscopy, and X-ray diffraction analyses. The mechanical properties of the fuel from Sirius-2A and -2B are discussed in a previous work. In this study, the results of the optical microscopy, scanning electron microscopy, and X-ray diffraction analyses are discussed.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2023

A liquid metal dropper for experiments on the wettability of liquid metals on plasma facing components

A liquid metal dropper has been developed as a part of the Ion-Gas-Neutral Interactions with Surfaces 2 (IGNIS-2) facility at The Pennsylvania State University. The dropper has the capability of directly applying drops to candidate plasma facing materials for nuclear fusion reactors to enable measurements of their liquid metal wetting properties. The results presented here are specific to the use of lithium in the dropper. This paper discusses the design choices of the liquid metal dropper and its chamber, including the heating and temperature control and the dropper’s motorized operation. Lithium drops of masses ranging from 0.05 g up to 0.13 g, equivalent to drop diameters between 5.6 mm to 1 cm, have been consistently dispensed by the dropper. A new algorithm is developed and used to automate the analysis of the contact angle between the liquid drops and substrate material for efficient analysis of video data recorded to study the wetting properties of candidate plasma-facing components.

Instruments & Instrumentation↗

DOE OSTI2021

Demonstration of CFD to support the coupled analysis of a reactor pressure vessel subjected to pressurized thermal shock

The structural components that comprise nuclear reactors and their supporting structures are subjected to harsh operating environments that can challenge their integrity, especially after exposure for extended duration or under accident condition. As one of the most significant components of a reactor, the Reactor Pressure Vessel (RPV) is exposed to an aggressive environment during the operation time (e.g. more than 40 years). Aging degradation mechanisms (e.g. thermo-fatigue) could grow initial defects up to a critical size, increasing the susceptibility to failure in the RPV. The conventional methods are mostly based on simple crack and structure geometries. Very limited studies consider the real conditions of the RPV subjected to a thermal shock due to a Loss of Coolant Accident (LOCA). During a LOCA event, the most severe conditions take place when the emergency core cooling (ECC) water is injected inside the cold legs filled initially with hotter water and/or steam. The rapid cooling of the down-comer and the internal RPV surface followed probably by re-pressurization of the RPV causes large temperature gradients and variation of pressure which induces thermal-mechanical stresses. In order to develop the model for integrity assessment of a reactor pressure vessel (RPV) subjected to pressurized thermal shock (PTS), a multi-physics simulation, which includes the thermo-hydraulic, thermo-mechanical and fracture mechanics analyses is necessary. The prediction of the temperature field is achieved by using computational fluid dynamics (CFD) simulation. In this report, a demonstration CFD standalone simulation is performed to support coupled analysis for Reactor Pressure Vessel (RPV) subjected to Pressurized Thermal Shock (PTS). The study use a simplified computational domain to represents a real RPV. The purpose of the study is to demonstrate the transient temperature response of RPV to ECC injection. The CFD model is built in a robust and efficient way for further coupled calculation. The next steps of this work, including the coupled thermal and tensor mechanics capabilities using Cardinal are expected to be complete by the end of FY21 for the demo problem. After this, into FY22, the capability will be demonstrated for a realistic RPV.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2023

Simulation and Analysis on Reactor Pressure Vessel (RPV) subjected to Pressurized Thermal Shock (PTS) under SBLOCA scenario by using Cardinal to support the fracture mechanics analyses

The structural components that comprise nuclear reactors and their supporting structures are subjected to harsh operating environments that can challenge their integrity, especially after exposure for extended durations or under accident condition. As one of the most significant components of a Reactor, the Reactor Pressure Vessel (RPV) is exposed to an aggressive environment during the operation time (e.g. more than 40 years). Ageing degradation mechanisms (e.g. thermos-fatigue) could grow initial defects up to a critical size, increasing the susceptibility to failure in the RPV. The conventional methods are mostly based on simple crack and structure geometries. Very limited studies consider the real conditions of the RPV subjected to a thermal shock due to a Loss of Coolant Accident (LOCA). During a LOCA event, the most severe conditions take place when the emergency core cooling (ECC) water is injected inside the cold legs filled initially with hotter water and/or steam. The rapid cooling of the down-comer and the internal RPV surface followed probably by re-pressurization of the RPV causes large temperature gradients and variation of pressure which induces thermal-mechanical stresses. In order to develop the model for integrity assessment of a reactor pressure vessel (RPV) subjected to pressurized thermal shock (PTS), a multi-physics simulation, which includes the thermo-hydraulic, thermo-mechanical and fracture mechanics analyses is necessary. The multi-physics simulations are performed using Cardinal, a wrapping of the GPU-oriented spectral element Computational Fluid Dynamics (CFD) code NekRS and other multi-physics sub-modules within the MOOSE framework. Cardinal now fully supports MOOSE stochastic perturbations of NekRS models with varying boundary conditions, initial conditions, material properties, and any other quantity which is defined by a kernel (such as coefficients in a momentum source model). The implementation is designed in a flexible manner so that scalar values are sent from MOOSE into a user scratch space in NekRS, which can then be applied for any purpose within the NekRS case files (both on the host and device). When modeling PTS, several factors can impact the results significantly. In this report, the impacts of the geometry of the model, Reynolds number and buoyancy effect are investigated. Two geometry, i.e., a simplified model and a realistic RPV model, with both laminar and turbulent flow condition are adopted for the PTS simulation with and without buoyancy effect. The purpose of the investigation is to understand the impact of these factors on the prediction of temperature history of RPV. The accurate prediction on the temperature evolution, which will be exported to Grizzly code for further analyses on the progression of aging mechanisms and their effects on the integrity of RPV structures, is very crucial. Based on the understanding of these factors, a more sophisticated model is built to analysis the PTS under SBLOCA scenario. A literature survey is conducted to pick the SBLOCA scenario for the multi-physics simulation. The analysis helps to explain the form and the transformation of the cold plum when the ECC is activated under SBLOCA. This model can be can be applied to study the PTS effect for different RPV configurations. The results can help to assess structural component degradation for advanced reactors.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2022

Multi physics simulation on Reactor Pressure Vessel (RPV) subjected to Pressurized Thermal Shock (PTS) by using Cardinal

The structural components that comprise nuclear reactors and their supporting structures are subjected to harsh operating environments that can challenge their integrity, especially after exposure for extended durations or under accident condition. As one of the most significant components of a Reactor, the Reactor Pressure Vessel (RPV) is exposed to an aggressive environment during the operation time (e.g. more than 40 years). Ageing degradation mechanisms (e.g. thermo-fatigue) could grow initial defects up to a critical size, increasing the susceptibility to failure in the RPV. The conventional methods are mostly based on simple crack and structure geometries. Very limited studies consider the real conditions of the RPV subjected to a thermal shock due to a Loss of Coolant Accident (LOCA). During a LOCA event, the most severe conditions take place when the emergency core cooling (ECC) water is injected inside the cold legs filled initially with hotter water and/or steam. The rapid cooling of the down-comer and the internal RPV surface followed probably by re-pressurization of the RPV causes large temperature gradients and variation of pressure which induces thermal-mechanical stresses. In order to develop the model for integrity assessment of a reactor pressure vessel (RPV) subjected to pressurized thermal shock (PTS), a multi-physics simulation, which includes the thermo-hydraulic, thermo-mechanical and fracture mechanics analyses is necessary.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2023

Methods and systems for rebalancing electrolytes for a redox flow battery system

A rebalancing reactor for a redox flow battery system may include a first side through which hydrogen gas is flowed, a second side through which electrolyte from the redox flow battery system is flowed, and a porous layer separating and fluidly coupled to the first side and the second side, wherein, the hydrogen gas and the electrolyte are fluidly contacted at a surface of the porous layer, and a pressure drop across the second side is less than a pressure drop across the porous layer. In this way, rebalancing of electrolyte charges in a redox flow battery system may be performed with increased efficiency and cost effectiveness as compared to conventional rebalancing reactors.

Evans, Craig E.↗

DOE OSTI2022

Weight function procedure for reduced order fracture analysis of arbitrary flaws in cylindrical pressure vessels

Fracture mechanics calculations using the finite element method can be computationally expensive, which makes them challenging to use in engineering evaluations of flaws in pressure vessels. The weight function (WF) technique is a reduced order fracture modeling method that is widely used to greatly reduce these computational costs. Its computational efficiency is essential for use in probabilistic fracture mechanics evaluations of embrittled nuclear reactor pressure vessels (RPVs), due to the large number of sampled flaws that must be evaluated. Although the WF technique is general, it is typically used only for axis-aligned flaws. Recent discoveries of off-axis flaws in operating nuclear reactors have necessitated detailed simulations of such flaws and the interactions between neighboring flaws. This paper presents a generalized WF approach applicable for analyzing arbitrary flaw geometries in thick-walled cylindrical vessels, including surface-breaking and subsurface flaws, which can either axis-aligned or off-axis, and can account for interactions with other flaws. Herein, this approach is demonstrated on representative simulations of multiple flaw geometries in a RPV subjected to transient loading conditions. In all cases, the WF technique gives good comparison with benchmark results from direct simulation with greatly reduced computational effort.

42 ENGINEERING↗

DOE OSTI2024

Plasmon-Driven Ammonia Decomposition on Pd(111): Hole Transfer’s Role in Changing Rate-Limiting Steps

Here, ammonia (NH 3 ) has the potential to be a hydrogen carrier because it can be transported and stored with ease, but only if it also can be decomposed easily when needed. Understanding how to control the frequently rate-limiting N–H bond breaking and N–N bond forming on catalytic surfaces may help design efficient means for NH 3 decomposition. Yuan et al. recently demonstrated photocatalytically selective N–H bond breaking in NH 3 on plasmon-driven aluminum–palladium (Al–Pd) antenna–reactor heterostructures. Using embedded correlated wavefunction (ECW) theory, we predict that the rate-determining step (RDS) for NH 3 decomposition on Pd(111) via thermocatalysis (dissociating the first N–H bond, *NH 3 → *NH 2 + *H, in the ground state, where * means adsorbed) differs from that via photocatalysis (dissociating the second N–H bond, *NH 2 → *NH + *H, in the excited state). This result is consistent with the measured catalytic efficiency and selectivity of NH 3 -deuterium (D 2 ) exchange reactions (an indirect way to measure N–H bond breaking) on Al–Pd heterodimers. We also determine the origin of the observed selectivity of thermocatalysis and photocatalysis on Pd(111) toward doubly deuterated (NHD 2 ) and monodeuterated (NH 2 D) products, respectively, and explore viability of the full NH 3 decomposition path, also via ECW theory. Additionally, we predict that the associative desorption of *N as N 2 from Pd(111) is extremely difficult in thermocatalysis at least at low surface coverages; metal-to-adsorbate hole transfer in photocatalysis stabilizes the transition state for the first N–H bond dissociation, shifting the RDS to the second N–H bond breaking. Furthermore, the redistribution of electrons around *N upon excitation reduces the electron density in the Pd–N bonds, which may lower the barrier for N 2 associative desorption in photocatalysis. Thus, light-induced, plasmon-mediated, excited-state hole transfer may provide an efficient mechanism to accelerate NH 3 decomposition.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗