Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Prediction of unsteady aerodynamic loadings caused by leading edge and trailing edge control surface motions in subsonic compressible flow: Analysis and results

A theoretical analysis and computer program was developed for the prediction of unsteady lifting surface loadings caused by motions of leading edge and trailing edge control surfaces having sealed gaps. The final form of the downwash integral equation was formulated by isolating the singularities from the nonsingular terms and using a preferred solution process to remove and evaluate the downwash discontinuities in a systematic manner. Comparisons of theoretical and experimental pressure data are made for several control surface configurations. The comparisons indicate that reasonably accurate theoretical pressure distributions and generalized forces may be obtained for a wide variety of control surface configurations. Spanwise symmetry or antisymmetry of motion, and up to six control surfaces on each half span can be accommodated.

Rowe, W. S.↗
NASA NTRS1975

High-efficiency graded band-gap Al/x/Ga/1-x/As-GaAs solar cell

A detailed theoretical analysis of an n-on-p graded band-gap Al(x)Ga(1-x)As-GaAs solar cell yields a maximum air mass zero power conversion efficiency of 17% compared to 9% for a similar GaAs cell. The analysis includes surface and bulk minority carrier recombination, junction recombination current, spectrally varying surface reflection, and series resistance loss. The maximum efficiency is determined for a surface recombination velocity of 10,000 cm/sec and hole and electron diffusion lengths of 2.1 and 7.6 microns, respectively. The improved efficiency is primarily due to a built-in electric field, caused by the band-gap gradation, accelerating photogenerated holes toward the p-n junction. This field reduces the surface and bulk recombination of the holes, and thereby enhances their collection.

Hutchby, J. A.↗
NASA NTRS1974

Geologic guide to the island of Hawaii: A field guide for comparative planetary geology

With geological data available for all inner planets except Venus, we are entering an era of true comparative planetary geology, when knowledge of the differences and similarities for classes of structures (e.g., shield volcanoes) will lead to a better understanding of general geological processes, regardless of planet. Thus, it is imperative that planetologists, particularly those involved in geological mapping and surface feature analysis for terrestrial planets, be familiar with volcanic terrain in terms of its origin, structure, and morphology. One means of gaining this experience is through field trips in volcanic terrains - hence, the Planetology Conference in Hawaii. In addition, discussions with volcanologists at the conference provide an important basis for establishing communications between the two fields that will facilitate comparative studies as more data become available.

Greeley, R.↗
NASA NTRS1977

A generalized vortex lattice method for subsonic and supersonic flow applications

If the discrete vortex lattice is considered as an approximation to the surface-distributed vorticity, then the concept of the generalized principal part of an integral yields a residual term to the vorticity-induced velocity field. The proper incorporation of this term to the velocity field generated by the discrete vortex lines renders the present vortex lattice method valid for supersonic flow. Special techniques for simulating nonzero thickness lifting surfaces and fusiform bodies with vortex lattice elements are included. Thickness effects of wing-like components are simulated by a double (biplanar) vortex lattice layer, and fusiform bodies are represented by a vortex grid arranged on a series of concentrical cylindrical surfaces. The analysis of sideslip effects by the subject method is described. Numerical considerations peculiar to the application of these techniques are also discussed. The method has been implemented in a digital computer code. A users manual is included along with a complete FORTRAN compilation, an executed case, and conversion programs for transforming input for the NASA wave drag program.

Miranda, L. R.↗
NASA NTRS1978

Low-speed aerodynamic characteristics of a 0.08-scale YF-17 airplane model at high angles of attack and sideslip

Data were obtained with and without the nose boom and with several strake configurations; also, data were obtained for various control surface deflections. Analysis of the results revealed that selected strake configurations adequately provided low Reynolds number simulation of the high Reynolds number characteristics. The addition of the boom in general tended to reduce the Reynolds number effects.

Petroff, D. N.↗
NASA NTRS1977

Asperity interactions in EHD contacts

Infrared temperature measurements, ferrographic analysis, and surface profilimetry were used to monitor asperity interactions in a sliding EHD point contact. The contact temperature and surface profile signals obtained both before and after a run-in period are compared in the frequency domain by means of a Fourier analyzer. The interaction of surface asperities is accompanied by the presence of a high frequency component in the infrared signal. It is also shown that only a relatively narrow band of wavelengths of the surface profile spectrum are relevant in the interaction process.

Nagaraj, H. S.↗
NASA NTRS1978

Energy distributions of sputtered copper neutrals and ions

Direct quantitative analysis of surfaces by secondary ion mass spectrometry will depend on an understanding of the yield ratio of ions to neutrals. This ratio as a function of the energy of the sputtered particles has been obtained for a clean polycrystalline copper surface sputtered by 1000-3000 eV Ar(+). The energy distributions of both neutral and ionized copper were measured with a retarding potential analyzer using potential modulation differentiation and signal averaging. The maximum for both distributions is identical and occurs near 2.5 eV. The energy distributions of neutrals is more sharply peaked than that of the ions, presumably as a consequence of more efficient nutralization of slow escaping ions by the mobile electrons of copper. The ion-neutral ratio is compared with results from various ionization models.

Lundquist, T. R.↗
NASA NTRS1979

Proportional counter for X-ray analysis of lunar and planetary surfaces

A position sensitive proportional scintillation detector was developed and evaluated for use in applications involving X-ray imaging as well as spectroscopy. Topics covered include limitations of the proportional scintillation counter for use in space; purification of the xenon gas in the detector, and the operation of the detector system. Results show that the light signal in a proportional scintillation detector remains well localized. With modest electric fields in xenon, the primary electrons from a photoelectric absorption of an X-ray can be brought a distance of a few millimeters to a higher field region without spreading more than a millimeter or so. Therefore, it is possible to make a proportional scintillation detector with good position sensitivity that could be used to calibrate out the difference in light collection over its sensitive volume.

Source record↗
NASA NTRS1979

Correlation of asperity contact-time fraction with elastohydrodynamic film thickness in a 20-millimeter-bore ball bearing

Elastohydrodynamic film thicknesses and asperity contact-time fractions were measured for a 20 mm bore ball bearing by using the capacitance and conductance techniques. The bearing was thrust loaded to 90, 445, and 778 N. The corresponding maximum stresses on the inner race were 1.28, 2.09, and 2.45 GPa. The test speed ranged from 400 to 15,000 rpm. The test bearing was mist lubricated with a MIL-L-23699A turbine oil. The temperature was 27 C. The experimental results were correlated to give the percent film (no-contact-time fraction) as a function of measured film thickness. Measurements were made for three test series that represented the test bearing in various conditions of run-in. The measurements show that the percent film changes with bearing run-in time. The experimental results agreed well with theoretical predictions based on surface trace analysis for a new bearing. For the run-in state, they agreed with previously reported experimental results. The results show that asperity contact existed at a film thickness-roughness ratio lambda of 6.0 or less for a new bearing. After run-in, no asperity contact occurred at a lambda of 3.5 or greater.

Coy, J. J.↗
NASA NTRS1979

The extended mission of Viking

The extended mission of the Viking project emphasizing the study of weather on Mars is presented. Samples were acquired for the analysis of surface material, and investigations were made of the physical and magnetic properties of the surface, with orbiters and landers producing large quantities of photographs of the surface and of atmospheric phenomena. The operation and chronology of Viking Orbiter 1 and 2 and Viking Lander 1, including the Viking continuation, the survey, and the orbiter completion missions are discussed.

Snyder, C. W.↗
NASA NTRS1980

Continuous analysis of stresses from arbitrary surface loads on a half space

A new form of elemental surface load on a half space is introduced, presuming a quasi-pyramidal variation of load which is doubly linear in each of four rectangular parts of a surface rectangle. Approximations of arbitrary load distributions by sums of such elements are continuous, piecewise linear in two directions and well adaptable. The loads may be normal or tangential. The explicit solutions obtained for all stress and displacement components due to each elemental load involve only elementary functions, are free of the discontinuities which arise with stepwise elements, and are suitable for computing. Some illustrative stress distributions are presented for elemental loads and for multiple pyramidal loads involving both normal and tangential loads. The value of the load continuity in the more complicated analyses of surface cracks is also illustrated.

Bell, J. C.↗
NASA NTRS1981

Characterization of rock populations on planetary surfaces - Techniques and a preliminary analysis of Mars and Venus

A data collection and analysis scheme developed for the interpretation of rock morphology from lander images is reviewed with emphasis on rock population characterization techniques. Data analysis techniques are also discussed in the context of identifying key characteristics of a rock that place it in a single category with similar rocks. Actual rock characteristics observed from Viking and Venera lander imagery are summarized. Finally, some speculations regarding the block fields on Mars and Venus are presented.

Garvin, J. B.↗
NASA NTRS1982

Reentry heat transfer analysis of the space shuttle orbiter

A structural performance and resizing finite element thermal analysis computer program was used in the reentry heat transfer analysis of the space shuttle. Two typical wing cross sections and a midfuselage cross section were selected for the analysis. The surface heat inputs to the thermal models were obtained from aerodynamic heating analyses, which assumed a purely turbulent boundary layer, a purely laminar boundary layer, separated flow, and transition from laminar to turbulent flow. The effect of internal radiation was found to be quite significant. With the effect of the internal radiation considered, the wing lower skin temperature became about 39 C (70 F) lower. The results were compared with fight data for space transportation system, trajectory 1. The calculated and measured temperatures compared well for the wing if laminar flow was assumed for the lower surface and bay one upper surface and if separated flow was assumed for the upper surfaces of bays other than bay one. For the fuselage, good agreement between the calculated and measured data was obtained if laminar flow was assumed for the bottom surface. The structural temperatures were found to reach their peak values shortly before touchdown. In addition, the finite element solutions were compared with those obtained from the conventional finite difference solutions.

Ko, W. L.↗
NASA NTRS1981

The crustal structure and tectonics of South America

A preliminary crustal structure map and a bibliography of crustal and upper mantle studies for South America are given. Work on the surface wave analysis and tectonic characterizations continues.

Keller, G. R.↗
NASA NTRS1982

Summary and recent results from the NASA advanced High Speed Propeller Research Program

Advanced high-speed propellers offer large performance improvements for aircraft that cruise in the Mach 0.7 to 0.8 speed regime. The current status of the NASA research program on high-speed propeller aerodynamics, acoustics, and aeroelastics is described. Recent wind tunnel results for five 8- to 10-blade advanced models are compared with analytical predictions. Test results show that blade sweep was important in achieving net efficiencies near 80 percent at Mach 0.8 and reducing near-field cruise noise by dB. Lifting line and lifting surface aerodynamic analysis codes are under development and some initial lifting line results are compared with propeller force and probe data. Some initial laser velocimeter measurements of the flow field velocities of an 8-bladed 45 deg swept propeller are shown. Experimental aeroelastic results indicate that cascade effects and blade sweep strongly affect propeller aeroelastic characteristics. Comparisons of propeller near-field noise data with linear acoustic theory indicate that the theory adequate predicts near-field noise for subsonic tip speeds but overpredicts the noise for supersonic tip speeds. Potential large gains in propeller efficiency of 7 to 11 percent at Mach 0.8 may be possible with advanced counter-rotation propellers.

Mitchell, G. A.↗
NASA NTRS1982

Flutter clearance of the horizontal tail of the Bellanca Skyrocket II airplane

The Skyrocket II is an all composite constructed experimental prototype airplane. A flutter clearance program was conducted on the horizontal tail so that the airplane could be safely flown to acquire natural laminar flow aerodynamic data. Ground vibration test data were used in a lifting surface flutter analysis to predict symmetric and antisymmetric flutter boundaries. Subcritical response data which were acquired during flight tests are compared with the analytical results. The final flutter clearance placard speed was based on flight test data.

Ricketts, R. H.↗