Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “speed”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

High-Speed Soft-Decision Decoding of Two Reed-Muller Codes

In this research, we have proposed the (64, 40, 8) subcode of the third-order Reed-Muller (RM) code to NASA for high-speed satellite communications. This RM subcode can be used either alone or as an inner code of a concatenated coding system with the NASA standard (255, 233, 33) Reed-Solomon (RS) code as the outer code to achieve high performance (or low bit-error rate) with reduced decoding complexity. It can also be used as a component code in a multilevel bandwidth efficient coded modulation system to achieve reliable bandwidth efficient data transmission. This report will summarize the key progress we have made toward achieving our eventual goal of implementing, a decoder system based upon this code. In the first phase of study, we investigated the complexities of various sectionalized trellis diagrams for the proposed (64, 40, 8) RM subcode. We found a specific 8-trellis diagram for this code which requires the least decoding complexity with a high possibility of achieving a decoding speed of 600 M bits per second (Mbps). The combination of a large number of states and a high data rate will be made possible due to the utilization of a high degree of parallelism throughout the architecture. This trellis diagram will be presented and briefly described. In the second phase of study, which was carried out through the past year, we investigated circuit architectures to determine the feasibility of VLSI implementation of a high-speed Viterbi decoder based on this 8-section trellis diagram. We began to examine specific design and implementation approaches to implement a fully custom integrated circuit (IC) which will be a key building block for a decoder system implementation. The key results will be presented in this report. This report will be divided into three primary sections. First, we will briefly describe the system block diagram in which the proposed decoder is assumed to be operating, and present some of the key architectural approaches being used to implement the system at high speed. Second, we will describe details of the 8-trellis diagram we found to best meet the trade-offs between chip and overall system complexity. The chosen approach implements the trellis for the (64, 40, 8) RM subcode with 32 independent sub-trellises. And third, we will describe results of our feasibility study on the implementation of such an IC chip in CMOS technology to implement one of these sub-trellises.

Lin, Shu↗
NASA NTRS1996

High-Speed Soft-Decision Decoding of Two Reed-Muller Codes

In his research, we have proposed the (64, 40, 8) subcode of the third-order Reed-Muller (RM) code to NASA for high-speed satellite communications. This RM subcode can be used either alone or as an inner code of a concatenated coding system with the NASA standard (255, 233, 33) Reed-Solomon (RS) code as the outer code to achieve high performance (or low bit-error rate) with reduced decoding complexity. It can also be used as a component code in a multilevel bandwidth efficient coded modulation system to achieve reliable bandwidth efficient data transmission. This report will summarize the key progress we have made toward achieving our eventual goal of implementing a decoder system based upon this code. In the first phase of study, we investigated the complexities of various sectionalized trellis diagrams for the proposed (64, 40, 8) RNI subcode. We found a specific 8-trellis diagram for this code which requires the least decoding complexity with a high possibility of achieving a decoding speed of 600 M bits per second (Mbps). The combination of a large number of states and a hi ch data rate will be made possible due to the utilization of a high degree of parallelism throughout the architecture. This trellis diagram will be presented and briefly described. In the second phase of study which was carried out through the past year, we investigated circuit architectures to determine the feasibility of VLSI implementation of a high-speed Viterbi decoder based on this 8-section trellis diagram. We began to examine specific design and implementation approaches to implement a fully custom integrated circuit (IC) which will be a key building block for a decoder system implementation. The key results will be presented in this report. This report will be divided into three primary sections. First, we will briefly describe the system block diagram in which the proposed decoder is assumed to be operating and present some of the key architectural approaches being used to implement the system at high speed. Second, we will describe details of the 8-trellis diagram we found to best meet the trade-offs between chip and overall system complexity. The chosen approach implements the trellis for the (64, 40, 8) RM subcode with 32 independent sub-trellises. And third, we will describe results of our feasibility study on the implementation of such an IC chip in CMOS technology to implement one of these sub-trellises.

Lin, Shu↗
NASA NTRS1995

Acceleration phenomena of high-speed wind observed at 0.1-0.3 AU with interplanetary scintillation

The radial distance dependence of solar wind speeds, which were measured by interplanetary scintillation method, has been studied especially for a high-speed solar wind, and large increase of the IPS speeds (300 km/s) was observed at the distance range of 0.1 - 0.3 AU. When the streams are mapped back onto the source surface, they distribute in polar coronal holes or their boundaries. Since the IPS measurement can be biased by several effects such as of line-of-sight integration, strong scattering and random velocities, we examined these biasing effects and have found difficulty to explain the large IPS speed increase with the biasing effects.

Kojima, M.↗
NASA NTRS1995

Dependence of velocity fluctuations on solar wind speeds: A simple analysis with IPS method

A number of theoretical works have suggested that MHD plasma fluctuations in solar winds should play an important role particularly in the acceleration of high speed winds inside or near 0.1 AU from the sun. Since velocity fluctuations in solar winds are expected to be caused by the MHD plasma fluctuations, measurements of the velocity fluctuations give clues to reveal the acceleration process of solar winds. We made interplanetary scintillation (IPS) observations at the region out of 0.1 AU to investigate dependence of velocity fluctuations on flow speeds. For evaluating the velocity fluctuation of a flow, we selected the IPS data-set acquired at 2 separate antennas which located in the projected flow direction onto the baseline plane, and tried to compare skewness of the observed cross correlation function(CCF) with skewness of modeled CCFs in which velocity fluctuations were parametrized. The integration effect of IPS along a ray path was also taken into account in the estimation of modeled CCFs. Although this analysis method is significant to derive only parallel fluctuation components to the flow directions, preliminary analyses show following results: (1) High speed winds (Vsw greater than or equal to 500 km/s out of 0.3 AU) indicate enhancement of velocity fluctuations near 0.1 AU; and (2) Low speed winds (Vsw less than or equal to 400 Km/s out of 0.3 AU) indicate small velocity fluctuations at any distances.

Misawa, H.↗
NASA NTRS1996

The 1995 NASA High-Speed Research Program Sonic Boom Workshop

The High-Speed Research Program and NASA Langley Research Center sponsored the NASA High-Speed Research Program Sonic Boom Workshop on September 12-13, 1995. The workshop was designed to bring together NASAs scientists and engineers and their counterparts in industry, other Government agencies, and academia working together in the sonic boom element of NASAs High-Speed Research Program. Specific objectives of this workshop were to (1) report the progress and status of research in sonic boom propagation, acceptability, and design; (2) promote and disseminate this technology within the appropriate technical communities; (3) help promote synergy among the scientists working in the Program; and (4) identify technology pacing the development of viable reduced-boom High-Speed Civil Transport concepts. The Workshop included these sessions: Session 1 - Sonic Boom Propagation (Theoretical); Session 2 - Sonic Boom Propagation (Experimental); and Session 3 - Acceptability Studies - Human and Animal.

Baize, Daniel G.↗
NASA NTRS1996

An Experimental Study of Ignition Effects and Flame Growth Over a Thin Solid Fuel in Low-Speed Concurrent Flow Using Drop-Tower Facilities

An experimental study of ignition and flame growth over a thin solid fuel in oxidizer flow speeds from 0 to 10 cm/sec concurrent flow was performed. This study examined the differences between ignition using a resistively heated wire (woven in a sawtooth pattern over the leading edge of the fuel), and a straight resistively heated wire augmented by a chemical ignitor doped onto the leading edge of the fuel. Results showed that the chemical system yielded non-uniform ignition bursts, while the system using only the hotwire gave more uniform ignition. At speeds up to 2.5 cm/sec, the chemical system yielded non-uniform pyrolysis fronts, while the hotwire system gave more uniform pyrolysis fronts. At speeds of 5 cm/sec or greater, both systems gave uniform pyrolysis fronts. The chemically-ignited flames tended to become too dim to see faster than the hotwire-ignited flames, and the flame lengths were observed to be shorter (after the initial burst subsided) for the chemical system for all speeds. Flame and pyrolysis element velocities were measured. Temperature profiles for selected tests were measured using thermocouples at the fuel surface and in the gas phase. Comparisons between the flame element velocities and peak temperatures recorded in these tests with calculated spread rates and peak temperatures from a steady-state model are presented. Agreement was found to be within 20% for most flame elements for nominal velocities of 5 cm/sec and 7.5 cm/sec.

Pettegrew, Richard Dale↗
NASA NTRS1961

Aerodynamic Characteristics of a Canard and an Outboard-Tail Airplane Model at High Subsonic Speeds

An investigation has been made in the Langley high-speed 7- by 10-foot tunnel through a range of Mach numbers from 0.60 to 0.95 of the static longitudinal and lateral stability and control characteristics of a canard airplane configuration and an outboard-tail configuration. The canard model had a twisted wing with approximately 67 deg of sweepback and an aspect ratio of 2.91 and was tested with three trapezoidal canard surfaces having ratios of exposed area to wing area of 0.032, 0.076, and 0.121. The canard model had a single body-mounted vertical tail. The outboard-tail model had its horizontal- and vertical-tail surfaces mounted on slender bodies attached to the wing tips and located to the rear and outboard of the 67 deg sweptback wing of aspect ratio 1.00. The data, which are presented with limited analysis, provide information at high subsonic speeds on these two types of high-speed airplanes which have previously been tested at supersonic speeds and reported in NACA RM L58BO7 and NACA RM L58E20.

Fournier, Paul G.↗
NASA NTRS1958

A Flight Evaluation of the Factors which Influence the Selection of Landing Approach Speeds

The factors which influence the selection of landing approach speeds are discussed from the pilot's point of view. Concepts were developed and data were obtained during a landing approach flight investigation of a large number of jet airplane configurations which included straight-wing, swept-wing, and delta-wing airplanes as well as several applications of boundary-layer control. Since the fundamental limitation to further reductions in approach speed on most configurations appeared to be associated with the reduction in the pilot's ability to control flight path angle and airspeed, this problem forms the basis of the report. A simplified equation is presented showing the basic parameters which govern the flight path angle and airspeed changes, and pilot control techniques are discussed in relation to this equation. Attention is given to several independent aerodynamic characteristics which do not affect the flight path angle or airspeed directly but which determine to a large extent the effort and attention required of the pilot in controlling these factors during the approach. These include stall characteristics, stability about all axes, and changes in trim due to thrust adjustments. The report considers the relationship between piloting technique and all of the factors previously mentioned. A piloting technique which was found to be highly desirable for control of high-performance airplanes is described and the pilot's attitudes toward low-speed flight which bear heavily on the selection of landing approach speeds under operational conditions are discussed.

Drinkwater, Fred J., III↗
NASA NTRS1997

High minor ion outflow speeds in the inner corona and observed ion charge states in interplanetary space

The study carried out in order to demonstrate that high minor ion outflow speeds of the order of O(5+) outflow speed are consistent with charge state observations is presented. The calculations were based on atomic data, observational constraints concerning electron temperatures, electron densities and flow speeds. Minor ion charge state observations were used in order to place limits on solar wind acceleration and heating mechanisms. The charge states of C, O, Fe and Si ions measured in situ were compared to those calculated from two solar wind models. The use of the planned ultraviolet and charge state observations in order to constrain both the ion outflow speeds and electron temperature is discussed.

Esser, R.↗
NASA NTRS1998

Effects of Planetary Speed Reduction Ratio on Mean Service Life

Planetary gear transmissions are compact speed reductions which use parallel-load paths to transmit high power. The range of possible reduction ratios is bounded from below and above by limits on the relative size of the planet gears. For a single plane planetary transmission, the speed-reduction ratio must be greater than two for planet gears to exist. As the ratio increase, so does the size of the planets relative to the sizes of the sun and ring. Which ratio is best for a planetary reduction can be resolved by studying a series of optimal designs. In this series, each design is obtained by maximizing the service life for a spur-gear planetary with a fixed size, speed reduction ratio, input speed, power and materials. The planetary gear reduction service life is modeled as a function of the two-parameter Weibull distributed service lives of the ball bearings and spur gears in the reduction. Planet-bearing life strongly influences the optimal reduction lives which point to an optimal planetary reduction ratio in the neighborhood of four to five.

Savage, M.↗
NASA NTRS1998

Effects of Planetary Speed-Reduction Ratio on Mean Service Life

Planetary-gear transmissions are compact speed reductions which use parallel-load paths to transmit high power. The range of possible reduction ratios is bounded from below and above by limits on the relative size of the planet gears. For a single-plane planetary transmission, the speed-reduction ratio must be greater than two for planet gears to exist. As the ratio increases, so does the size of the planets relative to the sizes of the sun and ring. Which ratio is best for a planetary reduction can be resolved by studying a series of optimal designs. In this series, each design is obtained by maximizing the service life for a spur-gear planetary with a fixed size, speed-reduction ratio, input speed, power and materials. The planetary-gear reduction service life is modeled as a function of the two-parameter Weibull distributed service lives of the ball bearings and spur gears in the reduction. Planet-bearing life strongly influences the optimal reduction lives which point to an optimal planetary reduction ratio in the neighborhood of four to five.

Savage, M.↗
NASA NTRS2000

A Method to Further Reduce the Perceived Noise of Low Tip Speed Fans

The use of low tip speed, high bypass ratio fans is a method for reducing the noise of turbofan jet engines. These fans typically have a low number of rotor blades and a number of stator vanes sufficient to achieve cut-off of the blade passing tone. Their perceived noise levels are typically dominated by broadband noise caused by the rotor wake turbulence - stator interaction mechanism. A 106 bladed, 1100 ft/sec takeoff tip speed fan, the Alternative Low Noise Fan, has been tested and shown to have reduced broadband noise. This reduced noise is believed to be the result of the high rotor blade number. Although this fan with 106 blades would not be practical with materials as they exist today, a fan with 50 or so blades could be practically realized. A noise estimate has indicated that such a 50 bladed, low tip speed fan could be 2 to 3 EPNdB quieter than an 18 bladed fan. If achieved, this level of noise reduction would be significant and points to the use of a high blade number, low tip speed fan as a possible configuration for reduced fan noise.

Dittmar, James H.↗
NASA NTRS2000

GPS Signal Scattering from Sea Surface: Wind Speed Retrieval Using Experimental Data and Theoretical Model

Global Positioning System (GPS) signals reflected from the ocean surface have potential use for various remote sensing purposes. Some possibilities arc measurements of surface roughness characteristics from which ware height, wind speed, and direction could be determined. For this paper, GPS-reflected signal measurements collected at aircraft altitudes of 2 km to 5 km with a delay-Doppler mapping GPS receiver arc used to explore the possibility of determining wind speed. To interpret the GPS data, a theoretical model has been developed that describes the power of the reflected GPS signals for different time delays and Doppler frequencies as a function of geometrical and environmental parameters. The results indicate a good agreement between the measured and the modeled normalized signal power waveforms during changing surface wind conditions. The estimated wind speed using surface- reflected GPS data, obtained by comparing actual and modeled waveforms, shows good agreement (within 2 m/s) with data obtained from a nearby buoy and independent wind speed measurements derived from the TOPEX/Poseidon altimetric satellite.

Komjathy, Attila↗
NASA NTRS1996

Speed Judgements of Transparent Stimuli

When two moving patterns are combined additively, observers often perceive two transparent surfaces, even when there are no cues supporting this segmentation in a frozen snapshot. We examined the ability of observers to make quantitative judgments about the speed of one of the patterns under these conditions. The component patterns consisted of band-pass filtered random noise presented in a spatial Gaussian contrast envelope, presented for 250 ms. On each trial a standard pattern appeared on one side of the fixation point, while a test pattern appeared on the other. The test pattern moved in the same direction as the standard, but with a speed which varied from trial to trial using a staircase procedure. The subjects' task was to report the side of the fixation point on which faster motion was seen. In some conditions the test stimulus was made to appear transparent by adding a mask pattern. When the mask was stationary, or moved slowly with respect to the test, no significant biases were introduced and discrimination performance was comparable to the no-mask condition (typically 3%). If the mask moved over the test with similar speed, however, the task became much harder, regardless of whether the mask moved opposite or orthogonal to the test. (Some subjects commented on a perceived directional repulsion between tests and orthogonally moving masks.) These results suggest the use of non-directional temporal channels in the performance of the speed discrimination task.

Mulligan, Jeffrey B.↗
NASA NTRS2003

Unbalance Response Prediction for Rotors on Ball Bearings Using Speed and Load Dependent Nonlinear Bearing Stiffness

Rolling-element bearing forces vary nonlinearly with bearing deflection. Thus an accurate rotordynamic analysis requires that bearing forces corresponding to the actual bearing deflection be utilized. For this work bearing forces were calculated by COBRA-AHS, a recently developed rolling-element bearing analysis code. Bearing stiffness was found to be a strong function of bearing deflection, with higher deflection producing markedly higher stiffness. Curves fitted to the bearing data for a range of speeds and loads were supplied to a flexible rotor unbalance response analysis. The rotordynamic analysis showed that vibration response varied nonlinearly with the amount of rotor imbalance. Moreover, the increase in stiffness as critical speeds were approached caused a large increase in rotor and bearing vibration amplitude over part of the speed range compared to the case of constant bearing stiffness. Regions of bistable operation were possible, in which the amplitude at a given speed was much larger during rotor acceleration than during deceleration. A moderate amount of damping will eliminate the bistable region, but this damping is not inherent in ball bearings.

Fleming, David P.↗
NASA NTRS2003

An Array of Frequency Selective Bolometers (FSB) for the Spectral Energy Distribution (SPEED) Camera

The SPEED camera is being developed to study the spectral energy distributions of high redshift galaxies using the Heinrich Hertz Telescope (HHT) in Arizona. SPEED requires a small cryogenic detector array of 2x2 pixels with each pixel having four frequency bands in the 150-350 GHz range. Here we describe the development of the detector array of these high efficiency FSBs. The FSB design provides the multi-pixel multi-spectral band capability required for SPEED in a compact stackable array. The SPEED bolometers will use proximity effect superconducting transition edge sensors as their temperature-sensing element allowing for higher levels of multiplexing in future applications.

Silverberg, R. F.↗
NASA NTRS1997

Enhancement of Mixing and Reaction in High-speed Combustor Flowfields

Research has been underway for a number of years, both in the United States and abroad, to develop advanced aerospace propulsion systems for use late in this century and beyond. One program is now underway at the NASA Langley Research Research has been underway for a number of years, both in the United States and abroad, to develop advanced aerospace propulsion systems for use late in this century and beyond. One program is now underway at the NASA Langley Research Center to develop a hydrogen-fueled supersonic combustion ramjet (scramjet) that is capable of propelling a vehicle at hypersonic speeds in the atmosphere. A part of that research has been directed toward the optimization of the scramjet combustor and, in particular, the efficiency of fuel-air mixing and reaction taking place in the engine. In the high-speed vehicle configurations currently being considered, achieving a high combustor efficiency becomes particularly difficult. With increasing combustor Mach number, the degree of fuel-air mixing that can be achieved through natural convective and diffusive processes is reduced leading to an overall decrease in combustion efficiency and thrust. Compressible shear layers and jets provide a good model for studying the physical processes occurring in high speed mixing and combustion in a scramjet. Mixing layers are characterized by large scale eddies that form due to the high shear that is present between the fuel and the air streams. These eddies entrain the fuel and air into the mixing region between the fluids leading to increased surface area and locally steep concentration gradients. Molecular diffusion then occurs across the strained interfaces. In an early study of high-speed mixing, Brown and Roshko show that the spreading rate of a supersonic mixing layer decreases with increasing Mach number, exhibiting a factor of three decrease in spread rate as compared with an incompressible mixing layer with the same density ratio. They conclude that the reduced spread rate is primarily due to compressibility. Papamoschou and Roshko also observe that the spreading rate of compressible mixing layers is significantly reduced over that of incompressible layers. To characterize the structure of the flow quantitatively, they define a convective Mach number. The reduction in mixing layer spreading rate is shown in these experiments to correlate well with increasing convective Mach number.

Drummond, J. Philip↗
NASA NTRS1997

Supersonic Quadrupole Noise Theory for High-Speed Helicopter Rotors

High-speed helicopter rotor impulsive noise prediction is an important problem of aeroacoustics. The deterministic quadrupoles have been shown to contribute significantly to high-speed impulsive (HSI) noise of rotors, particularly when the phenomenon of delocalization occurs. At high rotor-tip speeds, some of the quadrupole sources lie outside the sonic circle and move at supersonic speed. Brentner has given a formulation suitable for efficient prediction of quadrupole noise inside the sonic circle. In this paper, we give a simple formulation based on the acoustic analogy that is valid for both subsonic and supersonic quadrupole noise prediction. Like the formulation of Brentner, the model is exact for an observer in the far field and in the rotor plane and is approximate elsewhere. We give the full analytic derivation of this formulation in the paper. We present the method of implementation on a computer for supersonic quadrupoles using marching cubes for constructing the influence surface (Sigma surface) of an observer space- time variable (x; t). We then present several examples of noise prediction for both subsonic and supersonic quadrupoles. It is shown that in the case of transonic flow over rotor blades, the inclusion of the supersonic quadrupoles improves the prediction of the acoustic pressure signature. We show the equivalence of the new formulation to that of Brentner for subsonic quadrupoles. It is shown that the regions of high quadrupole source strength are primarily produced by the shock surface and the flow over the leading edge of the rotor. The primary role of the supersonic quadrupoles is to increase the width of a strong acoustic signal.

Farassat, F.↗