Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “small scale”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Performance analysis of hybrid power configurations: Impact on primary energy intensity, carbon dioxide emissions, and life cycle costs

In this work, utilization of Natural gas and Hydrogen to support current and future building energy needs to offset the total electric demand while improving the grid resiliency and energy efficiency was investigated. Demand side energy management will play an important role in efficiently managing the available energy resources. Performance assessment of different power generation and energy management configurations is presented in this paper. Development of solutions in addressing grid resiliency by providing the ability to design suitable configurations for meeting individual building energy needs is discussed. Primary movers (PM) such as internal combustion engines (ICE) and fuel cells (FC) along with small scale auxiliary renewable energy source such as photovoltaics (PV) were considered. Key attributes of total carbon foot-print, life cycle costs including capital and operational expenditure, electric grid offset or peak shaving capability, thermal energy availability and its further potential to offset total electric demand, and primary energy intensity are analyzed and discussed in detail.

08 HYDROGEN↗
DOE OSTI2023

Plasticity in irradiated FeCrAl nanopillars investigated using discrete dislocation dynamics

Here, in this paper, we investigate plasticity in irradiated FeCrAl nanopillars using discrete dislocation dynamics simulations (DDD), with comparisons to transmission electron microscopic (TEM) in situ tensile tests of ion- and neutron-irradiated commercial C35M FeCrAl alloy. The effects of irradiation-induced defects, such as a/2<111> and a<100> type loops and composition fluctuations representative of phase separation in irradiated FeCrAl alloys, are investigated separately as well as superposed together in simulations. We explore the effects of defects on the stress-strain behavior, specifically yield strength and hardening response, of FeCrAl nanopillars. Our simulations confirm the widely accepted fact that irradiated alloys exhibit a stress-strain response with higher yield strength as compared to unirradiated alloys. However, our DDD calculations reveal an atypical superposition of the hardening contributions due to composition inhomogeneity and irradiation loops wherein composition inhomogeneity annihilates the hardening due to irradiation loops at small scales. As a result, we observe that the yield strength in irradiated alloys, after taking into consideration the effects of both composition inhomogeneity and irradiation loops, is smaller than the yield strength of the alloys with only irradiation loops and is approximately same for the alloy with composition inhomogeneity alone. This is referred to as “destructive interference” between the hardening contributions due to composition fluctuations and irradiation loops in the paper. We also identify this destructive interference in the superposition in our parallel TEM in situ tensile tests on unirradiated, ion-irradiated, and neutron-irradiated C35M FeCrAl alloy. This destructive interference in the hardening contributions contrasts with the dispersed barrier hardening (DBH) models widely utilized by the experimental community to model the hardening contributions due to different irradiation induced defects. The effects of the loading orientations on the yield strength and hardening are investigated and the mechanisms for the hardening in irradiated FeCrAl alloys are also reported.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Novel geometries for air-cooled condensation of ammonia-water mixtures

An analytical and experimental investigation of air-cooled condensers for small-scale ammonia-water absorption heat pumps is presented. Conventional round-tube corrugated fin design and a novel multi-pass tube array design are considered for a condenser operating at severe ambient conditions within a compact footprint. Segmental heat and mass transfer models are developed to gain a deeper understanding of the characteristics of each design. Predicted heat duties are within 5% of the measured values. The limitations of correlations to predict air-side pressure drop in corrugated fins are identified. The performance of the novel multi-pass tube array condenser was comparable to that of conventional condensers, but is determined to be air-side limited throughout length of the heat exchanger. An improved multi-pass condenser design with fins for increased air-side area is proposed using the insights gained from the modeling and experiments. In closing this design meets the heat duty requirements at severe ambient conditions, while decreasing the size of the heat exchanger by 33%.

42 ENGINEERING↗
DOE OSTI2021

Moving toward a framework for electricity and heat equivalence in energy systems analysis

Sustaining, maintaining, and upgrading the electricity grid, while meeting decarbonization goals is a challenge facing policymakers, regulators, grid operators, and investors. Simultaneously meeting demands for future capacity, retiring older inefficient technologies, and addressing externalities from energy production and use requires more diverse and inclusive technologies to avoid constraints and shortfalls in grid capability. Changing the energy production paradigm by encouraging alternative technologies was a key driver for FERC Order 2222. This stimulus for developing new small-scale generation will complement and supplement the existing fleet only if it attracts new investment. This investment must reflect technology that goes beyond the energy-only characteristics of traditional generation, creating systems where suites of energy-equivalent outputs are enhanced by environmental quality benefits and offsets. We use energy system designs to highlight the contribution that measuring and accounting for equivalency values provides net increases in capacity, electricity, and alternative fuels while simultaneously reducing carbon waste impacts.

42 ENGINEERING↗
DOE OSTI2021

Bedrock architecture, soil texture, and hyporheic zone characterization combining electrical resistivity and induced polarization imaging

The shallow (<15 m depth) subsurface environment of a short reach along a bedrock stream was investigated with electrical resistivity and induced polarization (IP) to map details of bedrock and soil sediments. The bedrock is mostly comprised of limestone, and is generally resistive compared to the overlying soil. The soil-bedrock interface was determined through a trial and error approach using a sharp boundary feature in the inversion model. The inferred bedrock surface determined from the inversions exhibited undulating patterns with troughs and ridges. A near continuous trough ran alongside the stream within the floodplain, and is suggestive of a paleochannel among other interpretations of this feature. The structure of the electrical resistivity above the bedrock showed small-scale elongated features. The chargeability from the IP method showed larger scale features. High values of chargeability were associated with the sediments in the floodplain, and low values were associated with bedrock, stream, and soil on the elevated banks above the stream. If the chargeability is associated with membrane polarization characteristic of clayey soils, then IP seems to highlight the mere existence of clay, while the resistivity may be more discernable of the relative proportion of clay. Vegetation differences may also explain the chargeability distribution, where parts of the survey with high chargeability had dense pine with no understory making the soils more organically rich.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

A block-spectral adaptive H-/$p$-refinement strategy for shock-dominated problems

An adaptive H-/p-refinement strategy using a novel sensor is devised and tested in a block-spectral compressible Euler code equipped with adaptive-mesh refinement (AMR) and high-order flux-reconstruction numerics. At each Gauss quadrature point (or solution point) within each spectral block (or mesh element) the discrete velocity jump ΔU = ∂U/∂y 1 Δy 1 + ∂V/∂y 2 Δy 2 + ∂W/∂y 3 Δy 3 is calculated and normalized by the local speed of sound, a. Here, the grid spacing, Δx i , is calculated in each direction as the distance between auxiliary Gauss-Lobatto points, staggered relative to the solution points. The polynomial order is increased from p = 0 to p = p max in regions of weak compression, (ΔU/a) crit < ΔU/a < 0 and kept at p = p max in regions of flow expansion ΔU/a ≥ 0, while staying at the H = 0 base mesh level. Regions experiencing strong compressions, i.e. ΔU/a < (ΔU/a) crit , are H-refined up to H = H max where H max is applied at the location of maximum compression, ΔU/a = min(ΔU/a) in the domain, while keeping p = 0 to guarantee robustness and monotonicity of the solution in the H refined region. The critical value of (ΔU/a) crit = -0.06 is found to effectively separate smooth and non-smooth solution regions, supported by a 1D detonation initiation test case in ideal gas and a shock-to-detonation transition in high explosives. Using this value, the Sod shock tube, Shu-Osher problem, double Mach reflection and a 2D detonation in a high-explosive are simulated with the proposed adaptive H-/p-refinement. In the Sod shock tube case, p-refinement resolves the (weak) contact discontinuity while H-refinement enhances the grid resolution in the shock exploiting the monotonicity of the p = 0 reconstruction. For the Shu-Osher problem, p-refinement captures the small-scale oscillations trailing the shock that would be otherwise attenuated, while H-refinement triggered by the ΔU-sensor appropriately tracks the shock. In the double Mach reflection problem, H-refinement confines the numerical diffusion around the reflected shock while p-refinement recaptures many physical features trailing the shock. Finally, in the 2D high-explosive detonation case, H-refinement follows the leading shock and resolves the curvature of the detonation wave, while p-refinement adds resolution to the trailing reaction zone. Finally, the proposed methodology is tested in a detonation-wave propagation test case in high-explosives with numerical predictions comparing favorably against experiments.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2022

Decoupling indentation size and strain rate effects during nanoindentation: A case study in tungsten

Materials indented at small scales may simultaneously exhibit indentation size and strain rate effects which complicate the identification of the mechanisms that control deformation and strength. Here, in this work, we explore the possibility that indentation size and rate effects in some materials can be decoupled in a simple way. Nanoindentation tests with various load-time histories were carried out to measure the hardness of a tungsten single crystal over a wide range of indentation depths (~500–3600 nm) and indentation strain rates (~5 ×10 –5 –2 ×10 –1 s –1 ). Under these conditions, this material exhibits significant indentation size and rate effects, but the size effect is, to a good approximation, independent of strain rate. It is shown that this behavior can be understood by the Nix-Gao model for the indentation size effect modified to include the effects of a strain rate dependent friction stress. As a consequence, the size and rate dependencies of the hardness can be expressed as the sum of two independent terms: H($\dot{ε}$ i , h c )=H f ($\dot{ε}$ i ) + (H 0 – H f ) $\sqrt{1+ \frac{h^*}{h_c}}$, where H($\dot{ε}$ i , h c ) is the hardness at given indentation strain rate ($\dot{ε}$ i ) and contact depth (h c ), H f ($\dot{ε}$ i ) is the hardness contributed by the rate dependent friction stress, and (H 0 – H f ) and h* are size and rate independent constants that follow from the Nix-Gao analysis. This formula, together with an expression for the rate dependence of H f , was successfully applied to decouple the indentation size and rate effects observed in tungsten. In addition, the physics underlying the rate independence of indentation size effect is discussed, which provides guidance for application of the proposed approach to other materials.

42 ENGINEERING↗
DOE OSTI2021

Analysis of time-dependent strain heterogeneity in shales using X-ray microscopy and digital volume correlation

In this paper, we report the results of a 4-dimensional (3 spatial dimensions plus time) in-situ creep experiment on a milli-core shale plug from Barnett formation in Texas. An outstanding challenge in shale mechanics is connecting observable characteristics to predictable mechanical and hydraulic behavior. We employ novel imaging and analysis techniques to statistically link sample mineralogy and structure to observed deformation. In particular, we focus on mechanisms of porosity reduction during transient response to step changes in stress, analogous to the aseismic deformation that occurs after an episode of fracturing. Our main goal in this study is to take the first steps to visualize and capture the small-scale deformation mechanisms involved in creep of shales, using imaging techniques. To do so, we conducted a uniaxial creep experiment inside an Xradia Versa 520 micro-CT system for 12 h at room temperature under a constant uniaxial stress of 25 MPa. We employed a Digital Volume Correlation (DVC) method to measure micro-scale deforspmation of the sample by comparing the resulting volumetric images with a high-resolution scan of the sample obtained prior to the creep experiment. The results indicate that the time-dependent deformation in the compliant clay plus kerogen matrix constituents facilitates rigid grain rotation and compaction of intergranular porosity at the boundary between rigid grains and matrix.

58 GEOSCIENCES↗
DOE OSTI2020

Grand potential sintering simulations of doped UO 2 accident-tolerant fuel concepts

Chromium-doped UO is a widely-studied near-term deployable accident-tolerant fuel concept because it results in a dense, large-grain structure that increases the fuel resistance to densification, swelling, and fission gas release. A new charged-interstitial mechanism was recently proposed to describe the behavior of dopants like chromium in sintered UO 2 . Based on that mechanism, manganese was suggested as an even stronger dopant than chromium. In the current work we use mesoscale sintering simulations in an effort to validate the new mechanism. We compare the relative behavior of Cr-doped and undoped UO 2 against experimental data in the literature. We also make predictions of the relative behavior of Mn-doped UO 2 . Simulations are done using the phase field-based grand potential sintering model. Dopants have two effects on sintered UO 2 . They marginally increase the densification rate and greatly increase the average grain size. Both of these effects are individually tested in small-scale simulations. Then large 3D sintering simulations are used to test the combined behavior of both effects. The results for the densification rate simulations are consistent with experiments for Cr-doped fuels. However, we note the grain growth rates are lower than what is found in the literature for Cr-doped fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Effects of radiation damage and precipitate distribution on micro-pillar compression testing of irradiated CuCrZr

The results of small-scale mechanical tests are convoluted by the so-called size effect, whereby materials appear stronger when the scale of the test is reduced to the order of microns or less. The dimensional range over which this occurs has been shown to be linked to a change in sample microstructure, such as the addition of defects induced by irradiation. To investigate this response, a CuCrZr alloy was subjected to proton irradiation and mechanically tested using micro compression of pillars with a range in size. It was found that irradiation defects dominate over the extrinsic size effect and the sensitivity to differences in precipitate microstructure was also somewhat reduced, suggesting that size-independent results could be obtained from much smaller test volumes in irradiated material compared to their non-irradiated counterparts. Lastly, comparison was made between the increase in yield strength predicted by models and the experimentally measured values to establish the key parameters driving the strengthening behaviour.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Characterization of the molten salt FMgNaK through ab initio molecular dynamics and experimental density measurements

The selection of a salt species for use in a molten salt reactor MSR is a key part of any MSR design. However, many salts have sparse or no thermophysical property data sets, especially those with higher melting points. One such salt is the eutectic mixture of (NaF)0.345(KF)0.59(MgF 2 )0.065, or FMgNaK, and is explored here through ab initio molecular dynamics (AIMD) simulation (1023-1273K) as well as experimental measurement of the liquid density using the Archimedean method (973-1223K). Predicted densities from AIMD are similar to experimentally-measured densities, though with more noise, suggesting that the small scale necessitated by AIMD simulations may be problematic for simulating FMgNaK in particular. Here the coefficient of thermal expansion is predicted from simulation, and salt structure is characterized. Mg-F-Mg chaining is observed in the salt network, though the low concentration of Mg inhibits chaining on the scale that is observed in (LiF) 0.67 (BeF 2 ) 0.33 , or FLiBe.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Micro-tensile testing of the bond line in hot isostatic pressed aluminum

Considerable effort is being devoted to development and regulatory qualification of low enriched fuels for research and test reactors by many agencies worldwide. One promising fuel configuration being examined for United States higher power research and test reactors (USHPRRs) are plate-type fuels composed of a metallic uranium-molybdenum foil clad in an aluminum alloy. The two pieces of aluminum alloy cladding are bonded using a hot isostatic pressing method. The mechanical properties of the resulting bond line in the aluminum alloy cladding will vary by the HIP'ing parameters, requiring a need to characterize the bond line. Small scale mechanical testing can provide a path for evaluating the mechanical properties and deformation behavior of the bond line both prior to and following irradiation. Here, in this research, room temperature micro-tensile specimens of non-irradiated and irradiated samples containing an Al alloy (AA 6061) bond line were tested to evaluate its strength and deformation behavior. Observations indicated that the strain rate did not affect the deformation behavior or strength and most of the micro-tensile specimens failed in a ductile mode in grains around the bond line. There was no indication that the microstructural features from the bond line affected the mechanical properties of the micro-tensile specimens. An initial examination was performed on irradiated material but further systematic studies of the effects of irradiation can be performed in the future.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Impact of post-irradiation annealing on mechanical performance of irradiated 718 alloy

Here, the effect of post-irradiation annealing on solution-annealed 718 alloy was investigated using advanced mechanical testing, fractography, scanning electron microscopy, and transmission electron microscopy. Specimens were extracted from a proton beam window operated at the Spallation Neutron Source, irradiated with 940 MeV protons to a maximum dose of approximately 9.7 displacements per atom (dpa) at a calculated temperature not exceeding 110 °C while in service. Helium and hydrogen concentrations reached about 1700 and 6900 atomic parts per million (appm), respectively. Despite irradiation and high tensile strength (yield stress over 1 GPa), the material exhibited significant ductility. Annealing at 500 °C, 700 °C, and 900 °C for 30 min resulted in an appreciable decrease in yield strength and an increase in ductility for annealing treatments at 500 °C and 900 °C relative to the strength and ductility of the as-irradiated material. The presence of helium and hydrogen led to cavity formation and cleavage-like brittle features on fractured surfaces; however, high-magnification imaging revealed the presence of small-scale ductile dimples, indicating that the fracture mechanism remained mixed. The annealed specimens retained total elongation levels of 14–33 %, and there was no sudden drop in ductility after heat treatments. The ductility level in the irradiated and annealed material is notable despite the presence of helium and hydrogen.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Roll-to-roll production of catalyst coated membranes for low-temperature electrolyzers

Here we demonstrate a roll-to-roll (R2R) process for direct coating of anode catalyst layers on a polymer electrolyte membrane for low-temperature water electrolysis. To develop this process, we studied catalyst ink formulation, ink-membrane interactions, and coating quality. The catalyst inks were a mixture of iridium oxide (IrO2) and Nafion in a water and alcohol dispersion medium. The type of alcohol (methanol, ethanol, propanols) and water-to-alcohol ratio were varied to determine their influence on membrane swelling, dispersion quality, and coatability. Interactions of the ink dispersion medium with the membrane were characterized using sessile-drop contact-angle measurements. These measurements show that the ratio of water to alcohol has a strong influence on how rapidly the dispersion media is absorbed by the membrane. Rheology of the catalyst inks was measured to understand the microstructure of the catalyst particles in the ink. This analysis found that 1-propanol leads to better dispersion of the IrO2 particles than ethanol. Small-scale coating samples were prepared to understand coating uniformity and formation of irregularities. Subsequently, two water/1-propanol ratios (90:10 and 75:25) were down-selected for large-scale R2R slot die coating. The R2R catalyst-coated membrane (CCM) coating process increased catalyst layer production throughput by over 500x compared to our standard lab-scale spray coating. The CCMs obtained from this process were tested as single-cell membrane electrode assemblies. They exhibited a cell voltage of 1.91 V at a current density of 2 A/cm2, which is comparable to spray-coated CCMs. In conclusion, the work presented here demonstrates a continuous, scalable manufacturing process that eliminates the need for the decal transfer step typically used in CCM production.

42 ENGINEERING↗
DOE OSTI2023

Micro-beam bending of FCC bicrystals: A comparison between defect dynamics simulations and experiments

To understand the role of the grain boundary (GB) in plasticity at small scale, a concurrently coupled mesoscale plasticity model was developed to simulate micro-bending of bicrystalline micron-sized beams. By coupling dislocation dynamics (DD) with a finite element model (FEM), a novel defect dynamics model provides the means to investigate intricate interactions between dislocations and GBs under various loading conditions. Our simulations of micro-bending agree well with corresponding micro-bending experiments, and they show that mechanical response of bicrystals could have not only hardening but also softening depending on the characters of the GB. In addition, changing the location of the GB in the microbeams results in different mechanical responses; GBs located at the neutral plane show softening compared to single crystals, while inclined GBs located halfway along the length of the beam show little effect. In conclusion, simulation results could provide a clear picture on detailed dislocation-GB interactions, and quantitative resolved shear stress analysis supplemented by dislocation density distribution is used to analyze the mechanical response of bicrystalline samples.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Timing and synchronization of the DUNE neutrino detector

The DUNE neutrino experiment far detector has a fiducial mass of 40 kt. The O(1 M) readout channels are distributed over the 4 x 10kt modules and need to be synchronized to O(10 ns) with a reliable, simple, affordable system. For the majority of channels a simple DC-balanced protocol is used, with clock and synchronization information encoded on the same fibre. The remaining channels use “White Rabbit” (IEEE-1588). Small scale tests show a timing jitter of <100 ps. The DUNE timing system has been successfully prototyped at the ProtoDUNE-SP detector at CERN.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2022

Study of alkaline carbonate cooling to mitigate Ex-Vessel molten corium accidents

To mitigate adverse effects from molten corium following a reactor pressure vessel failure (RPVF), some new reactor designs employ a core catcher and a sacrificial material (SM), such as ceramic or concrete, to stabilize the molten corium and avoid containment breach. Existing reactors cannot easily be modified to include these SMs but could be modified to allow injectable cooling materials. Current reactor designs are limited to using water to stabilize the corium, but this can create other issues such as reaction of water with the concrete forming hydrogen gas. Here the novel SM proposed is a granular carbonate mineral that can be used in existing light water reactor plants. The granular carbonate will decompose when exposed to heat, inducing an endothermic reaction to quickly solidify the corium in place and producing a mineral oxide and carbon dioxide. Corium spreading is a complex process strongly influenced by coupled chemical reactions, including decay heat from the corium, phase change, and reactions between the concrete containment and available water. A recently completed Sandia National Laboratories laboratory directed research and development (LDRD) project focused on two research areas: experiments to demonstrate the feasibility of the novel SM concept, and modeling activities to determine the potential applications of the concept to actual nuclear plants. Small-scale experiments using lead oxide (PbO) as a surrogate for molten corium demonstrate that the reaction of the SM with molten PbO results in a fast solidification of the melt due to the endothermic carbonate decomposition reaction and the formation of open pore structures in the solidified PbO from CO 2 released during the decomposition. A simplified carbonate decomposition model was developed to predict thermal decomposition of carbonate mineral in contact with corium. This model was incorporated into MELCOR, a severe accident nuclear reactor code. A full-plant MELCOR simulation suggests that by the introduction of SM to the reactor cavity prior to RPVF ex-vessel accident progression, e.g., core-concrete interaction and core spreading on the containment floor, could be delayed by at least 15 h; this may be enough for additional accident management to be implemented to alleviate the situation.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2024

Evaluation of RANS vs. LES simulation of fluid flow through 3 × 3 rod bundle with a simple spacer grid as a precursor to coupled fluid–structure interaction simulations

The research literature on Computational Fluid Dynamics (CFD) of coolant flow through rod bundles with spacer-grids and mixing vanes is replete, ranging from high fidelity Large Eddy Simulation (LES)/Direct Numerical Simulation (DNS) simulations to Reynolds-Averaged Navier–Stokes (RANS) modeled studies. The mixing of flow between subchannels and the pressure drop through the bundle are fundamental quantities useful for comparing and evaluating CFD methods. Less commonly observed and compared are the forces exerted onto the structure by the fluid. The present study seeks to evaluate the use of RANS simulations for predicting the structural response to fluid flow. Wall resolved RANS simulations are benchmarked against LES simulations of fluid flow at a Reynolds number of 15,000 through a 3 × 3 fuel rod bundle with a simple spacer grid. Velocity line-plots are compared showing good agreement between RANS and LES results, ascertaining that the former is capable of capturing the essential time-averaged velocity profile. Additionally, the distribution of forces on the spacer grid and fuel rods are collected as a function of time and space. The RANS methods are evaluated using the frequency and magnitude of the fluctuating forces on various portions of the structure as compared to LES. In conclusion, the power spectral density evaluation of the models reveal underprediction of force amplitude on the rod walls by RANS and also discrepancy in the prediction of high frequency spectra, especially in the immediate vicinity of spacer-grid structure, which may be attributed to the lack of random turbulence fluctuation or insufficient modeling of small-scale eddies in RANS simulation.

FIV↗