Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “sinter”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Oxidation of porous stainless steel supports for metal-supported solid oxide electrolysis cells

Oxidation behavior of porous P434L ferritic stainless steel, used for the fabrication of metal-supported solid oxide electrolysis cells (MS-SOEC), is studied under oxygen-side and steam-side conditions. The impact of oxygen content on the oxygen side and steam:hydrogen ratio on the steam side is determined at 700°C for bare, as-sintered samples. For these conditions, oxidation is more aggressive in the steam-side atmosphere. Oxygen with 3% humidification and steam:hydrogen ratio of 90:10 are selected for further assessment with pre-oxidized, catalyst-coated, and CuMn1·8O4-coated samples. The rapid oxidation at 700°C and breakaway oxidation at 600 °C observed for bare stainless steel in 90:10 steam:hydrogen is mitigated by pre-oxidizing the sample in air before exposure. In oxygen, addition of the catalyst or CuMn 1·8 O 4 coatings moderately increases the oxidation rate, due to consumption of Cr via reaction between the coatings and Cr-oxide scale. In conclusion, the results for ex-situ controlled oxidation are similar to oxidation observed after 1000h operation of a full MS-SOEC. In general, the oxidation behavior at 700°C is found to be acceptable.

08 HYDROGEN↗
DOE OSTI2025

Linking structure to performance: Characterization of porous transport layers for high-pressure water electrolysis

Proton exchange membrane (PEM) water electrolysis is a promising technology to produce cost-efficient hydrogen. PEM electrolyzers offer a large current density range and the ability to operate at differential pressure which can be used to minimize both capital and operational expenditures. However, directly producing pressurized hydrogen at the cathode results in pushing the membrane against the anode porous transport layer (PTL). This can lead to detrimental effects, such as membrane deformation or ruptures, which depend on membrane properties as well as PTL material properties such as pore size, structure, and morphology. In this work, a range of sinter and felt-based commercial PTLs are evaluated for their contributions to the cell's electrochemical and H 2 crossover performance at cathode pressures up to 30 bar. X-ray tomography and post-operando optical microscopy are used to assess the morphology of the PTLs, and the PTL induced deformation experienced by the catalyst coated membrane (CCM), respectively. PTL samples with lower porosity were found to reduce both the cell voltage and the amount of H 2 permeating from the cathode to the anode exhaust, which was ascribed to improved catalyst layer contact and reduced membrane deformation, respectively. The best performing PTLs improved electrolyzer efficiency by ~1.5 kWh/kg H2 . Specifically, 1 kWh/kg H2 was gained due to reducing membrane deformation and decreasing H 2 crossover. The remainder 0.5 kWh/kg H2 were achieved by improving the electrical contact at the electrode/PTL interface which decreased cell voltage.

08 HYDROGEN↗
DOE OSTI2022

Shock compression behavior of stainless steel 316L octet-truss lattice structures

Lattice structures offer desirable mechanical properties for applications of energy absorption and impact mitigation but limited research has been carried out on their shock compression behavior. In this work, the shock compression behavior of stainless steel 316L (SS316L) octet-truss lattice structures was investigated through experimental techniques and numerical simulations. Plate impact experiments with high-speed imaging were conducted at impact velocities of 270 – 390 m/s on lattice specimens with 5x5x10 unit cell geometries additively manufactured (AM) using direct metal laser sintering. High-speed imaging together with digital image correlation was used to extract full-field measurements and define a two-wave structure consisting of an elastic wave and planar compaction (shock) wave which propagated along the impact direction. A linear shock velocity versus particle velocity relation was found to approximate the measurements with a unit slope and a linear fit constant equal to the crushing speed. Furthermore, the shock velocity versus particle velocity relation, full-field measurements, and elastic limit together with the Eulerian form of the Rankine-Hugoniot jump conditions were used to find relations for the stress and internal energy behind the shock. Stress behind the shock increased with relative density and particle velocity, and specific internal energy converged to a single curve similar to that of bulk AM SS316L. Explicit finite element analysis using the Johnson-Cook constitutive model demonstrated similar shock behavior observed in experiments and a linear shock velocity versus particle velocity relation and corresponding Hugoniot calculations were found to be in agreement with experimental results. Numerical simulations confirmed negligible effects of exterior versus interior measurements and further validated the application of one-dimensional shock theory.

42 ENGINEERING↗
DOE OSTI2023

Novel refractory high-entropy metal-ceramic composites with superior mechanical properties

A new concept of refractory high-entropy metal-ceramic composites (HEMCC) has been proposed that combines the outstanding physical properties of both high-entropy alloy (HEA) and high-entropy ceramic (HEC). As the first HEMCC system, to the best of our knowledge, TiTaNbZr-(TiTaNbZr)C, has been developed by a powder metallurgy process. The HEA and HEC phases exhibit body-centered cubic (BCC) and rock-salt B1 crystal structures, respectively, and both phases have non-equimolar chemical compositions. Further, with the increase of the HEC phase in HEMCC, the hardness is enhanced while the density and fracture toughness are decreased. HEA50C sintered from 50vol% HEA and 50vol% HEC precursor powders shows a favorable combination of flexural strength (541±48MPa) and fracture toughness (6.93±0.27 MPa·m 1/2 ) at room temperature and a high compressive strength at 1300ºC (275MPa). The optimized mechanical performance of HEMCC might be attributed to the combination of the ductile HEA and strong HEC phases, smaller grain size, and crack arrest at HEC/HEA interfaces.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Aluminum-doped U 3 Si 2 composite fuels with enhanced oxidation resistance

Al-doped U 3 Si 2 composite fuels with controlled microstructure were fabricated by spark plasma sintering that display greatly-improved oxidation resistance as compared with monolithic and Al-doped silicides prepared by standard powder metallurgy or arc melting. The effects of Al additives on the thermal-mechanical properties and oxidation resisance of the micron- and nano-sized U 3 Si 2 composites were investigated. Additionally, a minimal addition of 1.8 at% Al is effective to increase the onset oxidation temperature of as-fabricated U 3 Si 2 pellets to 580 °C, which can be further increased to 610 °C by thermal annealing. The Al-doped U 3 Si 2 composite fuels also display simultaneously higher hardness and fracture toughness than un-doped U3Si2. These results highlight an effective strategy by integrating minimal Al additives, microstructure control and post-thermal annealing to design advanced silicide fuels with excellent oxidation resistance, desired thermal-mechanical properties and maintained high fissile element density.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Synthesis of bulk reactive Ni–Al composites using high pressure torsion

Self-propagating exothermic reactions, for instance in the nickel-aluminum (Ni-Al) system, have been widely studied to create high performance intermetallic compounds or for in-situ welding. Their easy ignition once the phase spacing is reduced below the micron scale, makes top-down methods like high-energy ball milling, ideal to fabricate such reactive nanostructures. A major drawback of ball milling is the need of a sintering step to form bulk pieces of the reactive material. However, this is not possible, as the targeted reactions would already proceed. Therefore, we investigate the ability of high pressure torsion as an alternative process, capable to produce bulk nanocomposites from powder mixtures. Severe straining of powder mixtures with a composition of 50 wt% Ni and 50 wt% Al enables fabrication of self-reactive bulk samples with microstructures similar to those obtained from ball milling or magnetron sputtering. Additionally, samples deformed at ambient temperature are highly reactive and can be ignited significantly below the Al melting point, finally predominantly consisting of Al 3 Ni 2 and Al 3 Ni, independent of the applied strain. Although the reaction proceeds first at the edge of the disk, the strain gradient present in the disks does not prevent reaction of the whole sample.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Thermal Processing Conditions for the Synthesis of Near Theoretical Density Li 5 La 3 Ta 2 O 12 Ceramics for Ceramic Dual-Mode Detectors

A family of Li-containing garnet compounds, extensively investigated for Li-ion solid electrolyte applications, show great potential to be developed into transparent ceramic dual-mode scintillators. In particular, Li 5 La 3 Ta 2 O 12 (LLTaO) shows promise as an efficient dual-mode scintillator due to its high Li content, high density, non-hygroscopicity, and high effective-Z. Often the synthesis of LLTaO ceramics involves solid state processing techniques starting with oxide and carbonate powders, calcining, sintering for the removal of residual porosity, and post-processing. This study focuses on two objectives: (1) establishing thermal processing boundary conditions for a flexible alkoxide-based sol-gel method for synthesizing fine-grained powders; and (2), consolidating powders via hot-pressing to form high-density ceramics. In this study, near single-phase ceramics were achieved by hot-pressing sol-gel powders with varying amounts of excess Li. Rietveld refinements were used to analyze X-ray diffraction data and provide a quantitative evaluation of the phases present in the hot pressed ceramics. Some of the diffraction data showed large low angle peak asymmetry, suggesting the presence of two cubic Li 5 La 3 Ta 2 O 12 garnet phases with different lattice parameters. Depending on the synthesis and processing conditions, the refinement revealed ~ 90 wt% concentration of a phase with a ≈ 12.8 Å and ~ 10 wt% concentration of a phase with a ≈ 12.9 Å, indicating a remaining excess of Li in the hot pressed ceramics in the large lattice parameter phase. These synthesis experiments allowed for the determination of a baseline for Li loss during hot-pressing. X-ray excited radioluminescence and photoluminescence excitation and emission spectra were obtained from the hot pressed ceramics. In conclusion, the measured emission spectra featured broad tantalate emission and line emissions likely from a rare-earth impurity.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Re-investigation of high-temperature phase equilibria in Fe-rich Sm–Fe–Ti alloys

Recently renewed attempts to develop high-performance rare-earth-lean permanent magnets based on the Sm(Fe,Ti) 12 compound have drawn attention to the limited knowledge about the high-temperature phase equilibria in the Sm–Fe–Ti system. Experimental investigation of equilibrated alloys with electron probe microanalysis, X-ray diffraction and thermomagnetic analysis revealed several inaccuracies in the currently accepted phase relations at 1000°C and allowed for a revision of the Fe-rich corner of the Sm–Fe–Ti phase diagram. The Sm(Fe,Ti) 12 and Sm 3 (Fe,Ti) 29 phases were found to have more extended Ti ranges of 5.1–9.7 at% and 2.8–6.9 at%, respectively. With increasing of the Ti content, the Curie temperature of the Sm(Fe,Ti) 12 remains nearly constant at 306–312°C, whereas that of the Sm 3 (Fe,Ti) 29 increases from 188°C to 207°C. The low-titanium Sm 3 (Fe,Ti) 29 phase equilibrates not only with the Sm(Fe,Ti) 12 and Sm2(Fe,Ti) 17 phases, but also with (α-Fe) solid solution. Newly demonstrated equilibrium between Sm 2 (Fe,Ti) 17 and TiFe 2 phases makes impossible the earlier reported equilibrium between the Sm 3 (Fe,Ti) 29 and Sm(Fe,Ti) 11 phases. Because of an invariant reaction at 1000 °C, the revised phase diagram also features a class II four-phase equilibrium Sm 3 (Fe,Ti) 29 + TiFe 2 + Sm(Fe,Ti) 12 + Sm 2 (Fe,Ti) 17 . Peritectic decomposition of the Sm(Fe,Ti) 11 phase, which occurs either at 1075°C or at 1087°C, was found to have among its products the Sm(Fe,Ti) 12 phase. Although no such equilibration was attempted, it must be possible to obtain above 1087°C a two-phase state composed of the Sm(Fe,Ti) 12 phase and a liquid – which is important for manufacturing of the Sm(Fe,Ti) 12 - based permanent magnets via the liquid-phase sintering.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Role of washing solvents in defining the magnetic performance of Sm 2 Fe 17 N 3 obtained by reduction diffusion

Calciothermic reduction-diffusion (RD) is one of the leading synthesis methods for Sm 2 Fe 17 N 3 (SmFeN), but sintering of such RD-derived powders is hampered by oxidation and CaO byproducts. Here, we systematically evaluate how post-synthesis washing solvents govern powder chemistry and magnetic performance. RD-synthesized SmFeN powder was washed with several aqueous and non-aqueous solvents using identical washing protocols. This was followed by an assessment of both the as-washed powder as well as after annealing at 425 °C. Phase content was quantified by synchrotron PXRD and Rietveld refinement and SEM/EDS. The oxygen content of the powders was determined via inert gas fusion and the magnetization by DC magnetometry. While all aqueous-based solutions were able to remove CaO, the non-aqueous solutions were only effective with extended washing times. Prior to annealing, the crystalline phases and magnetic properties of the as-washed powders were largely the same regardless of washing solvent. However, differences emerge after annealing, where water-based washing markedly lowers the coercivity (H c ~3.8-4.3 kOe). In contrast, non-aqueous NH 4 Cl-methanol washing protocols were more effective in preserving coercivity (H c ~4.9-5.9 kOe). We attribute this to lower oxygen content in the non-aqueous samples (~9,400 ppm v ~6,400 ppm, respectively) which in turn reduced the formation of α-Fe during annealing. These results highlight the importance of solvent choice in washing RD-synthesized SmFeN and demonstrate that non-aqueous protocols, which better limit oxidation, outperform aqueous solvents despite the need for longer washing times.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effects of the method of active site characterization for determining structure-sensitivity in Ag-catalyzed ethylene epoxidation

We report catalysts have been prepared on a low surface area α-Al 2 O 3 support used commercially for previous generation olefin epoxidation catalysts. Prescreening of the low surface area alumina (0.73 m 2 /g) indicated the absence of acid catalyzed isomerization of EO at an evaluation temperature of 210 °C. A 0.1 wt% Ag base material synthesized by incipient wetness impregnation of AgNO 3 was used as a base material for electroless deposition (ED) of additional Ag to increase particle sizes by controlled reduction of Ag + directly onto the preexisting Ag surface to form weight loadings between 0.3 and 5.0 wt% metal. A 12 wt% Ag/α-Al 2 O 3 using Ag 2 C 2 O 4 as the Ag precursor was also prepared to compare performance of the ED samples with a catalyst more typical of industrial formulations. Characterization by SEM, STEM, and hydrogen titration of oxygen precovered Ag characterized before and after catalytic evaluation indicated that microscopy is required to accurately represent distributions of Ag particle sizes, but H 2 titration of O-precovered Ag gives the best representation of active sites since it directly counts the number of Ag surface sites. Larger particles >100 nm are resistant to both Ag sintering and carbon foulant; TOF values were relatively insensitive to particle size with only a 2.2 × difference between the best and worst performing samples. Selectivity, which is not a function of TOF, shows the most significant structure sensitivity effect where particle sizes follow the trend 67 nm ≈ 92 nm (58% EO) < 157 nm (67% EO) < 211–542 nm (73% EO). The lower EO selectivities were also correlated with increased fouling for the smaller Ag sizes, suggesting that more strongly bound EO precursor(s) leads to combustion and CO 2 /H 2 O formation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Surface Fe clusters promote syngas reaction to oxygenates on Rh catalysts modified by atomic layer deposition

Converting syngas to higher oxygenates is a promising strategy for sustainably producing fuels and chemicals used every day. Rh-based catalysts promoted with metal oxides have long been of interest for oxygenate synthesis, but the role of promoters and the structure of the catalyst during reaction are often not well understood. In this work, we characterize a Rh/SiO 2 catalyst modified by Fe 2 O 3 deposited by atomic layer deposition (ALD). Here, we show that Fe 2 O 3 deposits selectively on the Rh nanoparticles and enhances both the turnover frequency and the oxygenate selectivity of the catalysts. A maximum 29% selectivity towards higher oxygenates is achieved with just 1 cycle of Fe 2 O 3 ALD, and we relate the trends in selectivity to the changing availability of surface sites that drive higher alcohol (e.g., ethanol and propanol) formation. Further, we show that the ALD promoter mitigates catalyst sintering, improving the stability of these materials. In-situ X-ray absorption spectroscopy experiments reveal that the Fe 2 O 3 undergoes reduction during the catalyst pretreatment and forms Fe clusters on the surface of the Rh that migrate but remain stable under syngas reaction conditions. We find that modification of the Rh with these surface Fe species is key to the enhanced alcohol production observed in these materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Nitrogen-doped carbon for selective pseudo-metal-free hydrodeoxygenation of 5-hydroxymethylfurfural to 2,5-dimethylfuran: Importance of trace iron impurity

Heteroatoms-doped carbon materials have recently emerged as effective catalysts for various chemical and electrochemical reactions. The free of metals especially noble metals reduces cost and eliminates issues like sintering or leaching of metals at elevated temperatures in solvents. In this work, selective hydrodeoxygenation (HDO) of 5-hydroxymethylfurfural (HMF) to 2,5-dimethylfuran (DMF) is for the first time achieved over simple nitrogen-doped carbon (N-C) catalysts. Further, at optimal reaction conditions, a 91% yield of DMF is obtained with excellent catalyst stability. Extensive characterization, including extended X-ray absorption fine-structure (EXAFS) and soft X-ray absorption spectroscopy (sXAS), model reactions, basic data science analysis, and DFT calculations suggest that ppm of Fe in particular FeN 3 sites formed in pyrolysis, rather than non-metallic elements, drive key steps such as H 2 activation and deoxygenation of –OH during HMF HDO.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Thermodynamics and kinetics of interconversion between platinum nanoparticles and cations in zeolites

In metal-containing zeolites, sintering and redispersion processes exercise control over the identity of metal site structures, but the thermodynamic and kinetic factors that influence these molecular-level processes are not completely understood. Furthermore, we assess the ability of first principles informed free energy models (for supported and unsupported nanoparticles) and kinetic models integrating Ostwald ripening with atom trapping to describe the interconversion between Pt cations and nanoparticles encapsulated in chabazite (CHA) zeolites. Density functional theory-derived thermodynamic phase diagrams show that the interconversion between cations, favored in oxidizing environments, and particles, favored in reducing environments, is fully reversible within a wide range of their respective conditions (temperatures and pressures) for CHA and several other zeolite topologies. Kinetic Monte Carlo simulations of Pt redispersion are consistent with experimentally observed redispersion kinetics of encapsulated Pt nanoparticles in CHA zeolites, and model results suggest the zeolite host imparts additional stability for Pt nanoparticles. We envision our thermodynamic and kinetic models for Pt-CHA are also capable of describing nanoparticle and cation interconversions for other zeolite frameworks under similar conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Viscoelastic necking dynamics between attractive microgels

Hypothesis: Microgels can deform and interpenetrate and display colloid/polymer duality. The effective interaction of microgels in the collapsed state is governed by the interplay of polymer–solvent interfacial tension and bulk elasticity. A connecting neck is shown to mediate microgel interaction, but its temporal evolution has not been addressed. Here we hypothesize that the necking dynamics of attractive microgels exhibits liquid-like or solid-like behavior over different time and length scales. Experiments: We simulate the merging and pinching of attractive microgels with different crosslinking densities in explicit solvent using dissipative particle dynamics. The temporal coalescence dynamics of microgels is investigated and compared with simple liquid and polymeric droplets. We model the neck growth on long time scales using Maxwell model of polymer relaxation and compare the theoretical prediction with simulation data. The mechanical strength of the neck is characterized systematically via simulated pinch-off of microgels by steered molecular dynamics. Findings: We evidence a crossover in the coalescence dynamics reflecting the viscoelastic signature of microgels. In contrast to the common knowledge that viscoelastic materials respond elastically on short time scales, the early expansion of the microgel neck exhibits a linear behavior, similar to the viscous coalescence of liquid droplets. However, the late regime with arrested dynamics resembles sintering of solid particles. Through an analytical model relating microgel dynamics to neck growth, we show that the long-term behavior is governed by stress relaxation of the polymers in the neck region and predict an exponential decay in the rate of growth, which agrees favorably with the simulation. Different from coalescence, the thread thinning in microgel breakup primarily highlights its polymeric characteristics.

42 ENGINEERING↗
DOE OSTI2021

Constructing high-performance radiation-resistant ternary YSZ-MgO-CNT nanocomposites via tailored nanostructures

Developing long-lifetime bulk-form ceramic-based materials with high irradiation resistance is crucial for advanced nuclear systems. Here, we incorporated carbon nanotubes (CNTs) into yttria-stabilized zirconia (YSZ) and magnesia (MgO) nanocrystals to fabricate bulk YSZ-MgO-CNT nanocomposites with abundant ternary nanostructures by spark plasma sintering. To understand the role of tailored ternary nanostructure on irradiation, we investigated the microstructure and mechanical properties evolutions of the YSZ-MgO-CNT nanocomposites irradiated by multi-energy He + ions at high temperature to different fluences. Compared with the single-phase YSZ and ultrafine-grained YSZ-MgO composites, the YSZ-MgO-CNT nanocomposites possessed higher ability to manage irradiation-induced He bubbles/defects via the defect-interface interactions of proposed “loading-unloading” and “loading-transporting-unloading” mechanisms for controlling the dynamical behaviors of He atoms/defects in the CNT-doped ternary nanostructures, thereby presenting more stable microstructure and better performance in resisting irradiation hardening. In conclusion, this work provides insight into the design of advanced inert matrix nuclear fuel and new nuclear waste management materials.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Chemical durability and surface alteration of lanthanide zirconates (A 2 Zr 2 O 7 : A = La-Yb)

Chemical durability of lanthanide zirconates (A 2 Zr 2 O 7 ) (A = La-Yb) under near-field environments is important for evaluating their application as potential nuclear waste forms. In this work, A 2 Zr 2 O 7 (A = La-Yb) are synthesized by spark plasma sintering with controlled microstructure and their chemical durability are evaluated in a nitric acid solution (pH = 1). Scanning transmission electron microscopy analysis reveals an amorphous passivation film either enriched with Zr or lanthanide. The complex chemistry of the passivation films can be correlated with a transition in corrosion mechanisms from a preferential release of lanthanide in La 2 Zr 2 O 7 to a preferential release of Zr in Er 2 Zr 2 O 7 and Yb 2 Zr 2 O 7 . These results suggest a dominant mechanism of incongruent dissolution and surface reorganization for the formation of passivation films. Strong correlations are identified between the leaching rates and cation ionic size, ionic potential, electronegativity differences between A-site cation and Zr, and bonding valence sum of oxygen, suggesting important impacts of structural and bonding characteristics in controlling chemical durability of lanthanide zirconates.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Hidden transformations in entropy-stabilized oxides

We report entropy-stabilized oxides (ESO) display a reversible entropy-driven phase transformation that can be leveraged to produce a continuum of metastable phase states, allowing for property optimization and novel functionalities. X-ray absorption spectroscopy reveals that entropic stabilization extends to the electronic structure (valence state and cation coordination) in sintered (Co,Cu,Mg,Ni,Zn)O, manifesting as a tunable lattice distortion in the entropy-stabilized phase. Co, Cu, and Zn ions reversibly transform from six-fold to four-fold coordinated structures and from low to high valence states due to the competition between electronic structures that are equilibrium and enthalpy-driven or metastable and entropy-driven. The segregation of a Cu-rich tenorite phase and a Co-rich spinel phase influences the electronic structure evolution. ESOs can adjust their electronic structures through heat treatment, providing a powerful tool for developing functional properties. These results indicate that the definition of entropy stabilization should include entropy-stabilized electronic structures, providing motivation to reassess previously studied HEO materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Synthesis of high-entropy carbides from multi-metal polymer precursors

Three compositions of high-entropy carbides, (TiHfVNbTa)C, (TiZrHfNbTa)C and (TiZrNbTaW)C were synthesized via a modified Pechini process, in which citric acid served as both a cation chelating agent and a carbon source. Through pyrolysis and spark plasma sintering, single phase high-entropy carbides were formed from the homogeneous precursors at a relatively low temperature of 1800 °C. The dispersion of cations in the polymer precursor facilitated shorter diffusion distances in polymer-derived materials, and thus compositional homogeneity was significantly improved relative to materials produced by a solid-state method, as quantified by a defined coefficient of variation applied to energy-dispersive X-ray spectroscopy. Finally, a finer microstructure in polymer-derived materials results in improved fracture toughness with a K IC value of 4.29 MPa·m 1/2 achieved for (TiHfVNbTa)C.

36 MATERIALS SCIENCE↗