Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “sinter”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Processing and characterization of the homologous Zr x Ta 2 O 2x+5 series

In this study, Zr x Ta 2 O 2x+5 (ZTOx) was systematically studied to determine ideal solid-state synthesis and pressureless sintering conditions. For Zr 6 Ta 2 O 17 (ZTO6) and other compositions with values of x in ZTOx the optimal synthesis temperature of 1100 °C with 1 h dwell time was optimal. XRD phase analysis of the homologous series indicated that for ZTOx, x = 5, 6, 7, and 8 were within the phase stability field while x = 4 and x = 9 were outside the phase stability field. Unit cell lattice parameters changed anisotropically with Zr:Ta ratio with an overall <0.1% change in unit cell volume across the solid solution. Some Raman modes red shifted while others blue shifted, indicating competing tensile and compressive strains. Sintering of ZTOx required a progressively higher temperature as Zr-content increased despite the same starting powder grain sizes and synthesis temperature. Higher Vickers hardness for Zr-rich (12.7–12.8 GPa) than Ta-rich Zr x Ta 2 O 2x+5 (11.6–11.7 GPa) disappeared when accounting for different sintering temperatures. Indentation toughness was similar for all compositions (1.2–1.4 MPa m 1/2 ). Properties of Zr x Ta 2 O 2x+5 series indicate tunability of Zr:Ta composition ratio while maintaining the structure and room temperature mechanical properties comparable to Hf 6 Ta 2 O 17 and 8 mol% yttria stabilized zirconia ceramics.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Physicochemical properties of digital light processing 3D-Printed alumina and mullite ceramics

Alumina ceramics fabricated using conventional techniques such as uniaxial pressing or injection molding are popular due to their low density, excellent insulation, and mechanical properties. However, these methods often limit the fabrication of complex geometries with high dimensional accuracy due to tooling constraints and limited design freedom. To overcome these limitations, this study employed Digital Light Processing (DLP) additive manufacturing (AM), which enables the production of precise structures. In addition, the optimization of sintering parameters to enhance the densification and performance of alumina and mullite ceramics was investigated, with a specific focus on how varying sintering temperatures and hold times affect part shrinkage, geometric accuracy, and material integrity. Flexural strength of both alumina and mullite specimens was clearly influenced by the way the layers was stacked. When layers were arranged across the direction of the applied load (Z = 4; XZ), the strength was higher than when they were stacked along the same direction as the load (Z = 3; XY). Weibull analysis based on these results showed high modulus values across all samples, indicating good reliability in the flexural strength measurements. This reliability, combined with the clear influence of sintering parameters, highlights how processing conditions effect the material properties and mechanical performance of parts produced through DLP additive manufacturing. In conclusion, these findings open new avenues for ceramic AM across various applications, enhancing the potential for innovation in fields such as aerospace, biomedical engineering, and energy.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Manufacturing porous U10Zr fuels with controlled porosities by SPS and thermal properties

To accommodate the swelling of metallic fuels induced by the fission gas release during burnup in sodium fast reactor for a sodium-free fuel option, advanced U-10Zr fuels with controlled porosity were designed and demonstrated by spark plasma sintering. U-10Zr fuel pellets with manufactured porosities varying from 35% up to fully dense fuel pellets have been fabricated by controlling ball milling times of the starting uranium powders, sintering temperature, pressure, and duration, and the correlation among the microstructure control – porosity – sintering conditions has been established. To further mimick the pore structure in irradiated fuels, different pore formers (NaCl and NH4HCO3) have been used to control the pore size and distribution. Microstructure characterization indicates a lamellar reaction zone of U and Zr, differing from the arc-melted U-10Zr as a result of rapid consolidation of SPS at lower temperature and short durations. The thermal conductivity of U10Zr with different porosities are also measured. Here this work demonstrates the success in manufacturing new metallic fuel forms with controlled porosities and pore distribution, which can be used as model systems to investigate the thermal transfer behavior of metallic fuels in the reactor.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Unraveling the conundrum of electronic leakage in protonic ceramic cells: Operation-specific insights and rational design strategies

Electronic conduction through proton-conducting electrolytes significantly impairs the efficiency of protonic ceramic cells (PCCs). Here, in this study, we explore the electron and ion mixed transport properties of four common protonic ceramics, BaZr 0.8 Y 0.2 O 3-δ (BZY82), BaZr 0.7 Ce 0.2 Y 0.1 O 3-δ (BZCY721), BaZr 04 Ce 0.4 Y 0.1 Yb 0.1 O 3-δ (BZCYYb4411), and BaZr 0.1 Ce 0.7 Y 0.1 Yb 0.1 O 3-δ (BZCYYb1711). It marks the first instance of investigating these properties under operation-specific scenarios: fuel side of electrolysis cell, air side of electrolysis cell, fuel side of fuel cell, and air side of the fuel cell. BZCYYb1711 exhibits the highest ionic conductivity, but two to three times higher electronic leakage when exposed to oxygen-containing environments than the others. BZY82 exhibits approximately two times higher electronic leakage in a hydrogen-containing environment. BZCY721 demonstrates excellent ion transport numbers (~0.95) across these four operating conditions. BZCYYb4411 behaves quite similarly to BZCY721. The most challenging operating environment for all candidates is the air side of fuel cell mode. This mode leads to a high initial electronic leakage, followed by a significant increase with polarization. The probable cause for this behavior is a H 2 -free, polarization-induced reduction that leads to the formation of V$^•_O$. The electron small polaron associated with V$^•_O$ is released by the electrical field due to the Poole-Frenkel effect. ZnO and NiO sintering aids are found to be detrimental to the ionic conductivity of the electrolytes. In particular, NiO substantially lowers the ion transport number. The correlation of the operation-specific electronic leakage to full cells is discussed. It is suggested that a rational PCC design should synergistically couple BZCYYb1711 at fuel side with BZCY4411 at air side to deliver a well-balanced performance and faradaic efficiency simultaneously, and the high temperature sintering process with a NiO fuel electrode should be shortened or replaced by ultra-fast sintering techniques or using a fuel electrode scaffold-infiltration fabrication strategy.

42 ENGINEERING↗
DOE OSTI2023

Compositional inhomogeneity and its effect on the hardness of nanostructured refractory high-entropy alloys

The pronounced compositional inhomogeneity observed in refractory high-entropy alloys (HEAs), as opposed to non-refractory HEAs, has an important influence on their mechanical properties, thereby posing a significant challenge for the development of high-performance refractory HEAs. In this work, by combining transmission electron microscopy imaging, chemical analysis, and nano-hardness tests, we investigate the compositional inhomogeneities in a series of sintered nanostructured HEAs and elucidate their influence on the material's hardness. Further, we reveal that the compositional inhomogeneity of the sintered nanostructured HEAs is temperature- and component- dependent. By correlating the hardness of nanostructured HEAs to the evolving compositional inhomogeneity, our work demonstrates that the compositional inhomogeneity in nanostructured HEAs can be tuned by sintering temperature or alloying towards optimized microstructure and hardness.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2022

Size-Dependent Adsorption and Adhesion Energetics of Ag Nanoparticles on Graphene Films on Ni(111) by Calorimetry

Interest in the use of carbon supports for late transition metal nanoparticle catalysts has expanded rapidly due to the increasing importance of electrocatalysts for clean energy and environmental technologies and the use and storage of renewable electricity. Compared to oxide supports, almost nothing is known about the effect of metal nanoparticle size on the energies of the metal atoms within carbon-supported nanoparticles, yet these energies are crucial for understanding their surface reactivity and sintering kinetics. Here, the growth morphology and adsorption energetics of vapor-deposited Ag onto clean graphene/Ni(111) surfaces have been studied using a combination of single-crystal adsorption calorimetry (SCAC) and He + low-energy ion scattering (LEIS). The differential heat of Ag adsorption is 207 kJ/mol for making ~30 atom Ag particles on graphene terraces at 100 K and 16 kJ/mol higher for making ~9 atom Ag clusters at defect sites at the same temperature. The heat of adsorption increases rapidly with Ag coverage as 3D Ag nanoparticles nucleate and grow in size, asymptotically reaching within 5 kJ/mol of the bulk Ag sublimation enthalpy (285 kJ/mol) by 2 ML. The heats of adsorption and Ag nanoparticle densities from LEIS (~10 16 /m 2 ) were combined to provide the Ag/graphene adhesion energy (E adh = 1.8 J/m 2 in the large-particle limit) and the Ag chemical potential (μ) versus effective particle diameter (D). The Ag chemical potential was well-fitted by μ(D) = (3γ v /M – E adh )(1 + (1.5 nm)/D)(2V m /D), where γ v /M is the surface energy of bulk Ag and V m is its molar volume. The same equation is known to fit similar data for late transition metals on clean surfaces of metal oxide single crystals. The adhesion energy of Ag measured here on graphene falls within the wide range measured for Ag on those oxide surfaces and is almost as large as on the oxide that binds Ag particles most strongly, namely CeO 2 (111), which is well-known to be very effective at resisting catalyst deactivation by metal sintering. Furthermore, these results imply that carbon supports will be effective at resisting sintering and that Ag particles smaller than 6 nm on graphene will bind small adsorbed reaction intermediates more weakly than supports with weaker adhesion to Ag, like MgO(100).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Aerosol jet printed 3 omega sensors for thermal conductivity measurement

The 3 omega (3ω) method is a trusted technique for measuring thermal conductivity—a fundamental material property of critical importance in a broad range of applications. However, traditional 3ω sensor processing requires some form of physical vapor deposition, such as metal evaporation or sputtering. These 3ω sensor deposition techniques limit the materials and sample sizes applicable to the 3ω method. This work demonstrates an aerosol jet printing method to directly print silver 3ω sensors that yield accurate temperature-dependent measurement up to 300 °C on materials with thermal conductivity ranging from 1 to 150 W/m K. The interrelationship between printed sensor geometry, sensor thermal stability, and applicability to the 3ω method is examined. Thermal conductivity measurement with 3ω sensors conventionally sintered at 300 °C agrees to independent laser flash measurement within 4% from room temperature to 150 °C. An unconventional rapid high-temperature sintering method is shown to produce sensors that agree within 3% of the laser flash measurements from room temperature to 300 °C. The rapid sintering profiles also reduced the sensor–substrate thermal boundary resistance of the printed sensors by as much as 88%. The direct printing of 3ω sensors creates opportunities for measurement of thermal transport properties in applications previously inapplicable to the 3ω method.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

Fabrication of UN-Mo CERMET Nuclear Fuel Using Advanced Manufacturing Techniques

Ceramic-metallic nuclear fuels are a candidate fuel for nuclear thermal propulsion systems due to their high heat transport properties, which are necessary in very high-temperature environments. The conventional fabrication of uranium nitride–molybdenum fuel has been thoroughly studied in the past, but modern manufacturing techniques have presented a unique opportunity for further development within this field. This work demonstrates the use of advanced manufacturing techniques to produce nuclear fuel pellets composed of uranium nitride microspheres encased in a molybdenum matrix. Binder jetting is used to print molybdenum disks that are filled with uranium nitride microspheres and afterward sintered using spark plasma sintering. Two fuel pellets were fabricated to demonstrate the methodology and to provide a baseline analysis of the effects of temperature and pressure processing conditions. Characterization of the sintered fuel pellets includes detailed microstructural analysis and thermal conductivity measurements.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Coupling between interfacial charge and mechanical deformation at high temperatures in ceramics. Final report

Basic research, under this project, has led to new fundamental discoveries in the effect of electric field (and temperature) on diffusion kinetics, electroluminescence and electronic conductivity in ceramic materials. For example, yttria stabilized zirconia sinters in just seconds well below 1000°C, while, at the same time, exhibiting a highly non-linear rise in conductivity, and intense electroluminescence. The phenomenon has been shown to occur in nearly all ceramics whether they are ionic or electronic conductors, or insulators. The rise in conductivity leads to Joule heating but in-situ measurements with a platinum standard at APS and Brookhaven (NSLS-II) have shown that the temperatures are much below what would have been needed to sinter in a few seconds. We have explored the hypothesis that huge concentrations of Frenkel pairs of vacancies and interstitials are produced. While these point defects accelerate sintering (by the interstitials being transported to the pores and the vacancies to the grain boundaries), they may also produce electron-hole pairs which can impart high electrical conductivity or recombine to emit photons. Many measurements, including in-situ measurements of lattice expansion are consistent with this hypothesis. However, the energy barrier for generating Frenkels in zirconia for example is much larger than can be expected at temperature and electrical fields in these experiments. Most recent work suggests that short wavelength phonons play a critical role in the genesis of the “flash” phenomenon. For example, the Debye temperature has been shown to be the lower bound for initiating flash. Molecular dynamics simulations have shown that large concentrations of Frenkel pairs can form under the proliferation of “optical” phonons at the edge of the Brillouin zone, that is with a wavelength at or below the lattice parameter. This project has led to the development of new experimental techniques as well as a software hardware interface for process and control and data analysis in real time, with a time scale of less than one second. This approach spells a new paradigm in materials science research. It potential impact on high rate manufacturing is self evident.

36 MATERIALS SCIENCE↗
DOE OSTI2023

A Study of a Surrogate Nuclear Thermal Propulsion Fuel Element

We report a surrogate fuel, Zirconium Carbide/Titanium Nitride has been prepared using a simple method to obtain a more uniform distribution of titanium nitride in the zirconium carbide matrix. Powders were sintered using Spark Plasma Sintering at 1750oC and 1850oC using a modified sintering profile. This resulted in a fairly uniform distribution of titanium nitride in the zirconium carbide matrix with a density of 95% of theoretical at 1850oC. Scanning electron microscopy, indentation hardness and x-ray diffraction results are given.

36 MATERIALS SCIENCE↗
NASA NTRS2023

Homogeneity Study of ZrC, NbC, and TaC Binary Carbide Fuels for the Application of Nuclear Thermal Propulsion

In alignment with NASA and DARPA goals, efforts towards Nuclear Thermal Propulsion (NTP) have increased in recent years. As progress is made, a main challenge still exists; the fuel in an NTP system must survive the extreme environment experienced during operating conditions. Three fuel forms have been studied including a ceramic-metallic matrix, a ceramic-ceramic matrix, and solid solution carbides. Solid solution carbides were studied previously as a fuel for NTP and was shown to be a promising technology; however, the programs were canceled before demonstration in an NTP engine test. Of the refractory metal carbides of interest, zirconium carbide (ZrC), niobium carbide (NbC) and tantalum carbide (TaC) were studied. ZrC, NbC, and TaC powders were consolidated in monocarbide (ZrC, NbC, TaC) and bi-carbide (ZrC-NbC, ZrC-TaC, NbC-TaC) forms using spark plasma sintering (SPS), with 50-50 mol% compositions of the bi-carbides of interest. The time and temperature conditions to achieve a completely homogeneous solid solution for the mixed carbides is of interest for NTP fuel applications, since this homogeneity is considered to be essential for this fuel form. Homogeneity is typically not achieved during sintering, as surface diffusion (predominant for sintering to near ideal density) tends to occur at lower temperatures than bulk volumetric diffusion (required for solute interdiffusion to achieve a homogeneous solid solution). High temperature isochronal annealing was performed to identify the conditions to achieve a chemically homogeneous sample. The solute interpenetration vs annealing temperature was quantified using energy dispersion spectroscopy (EDS) in a scanning electron microscope (SEM). X-ray diffraction (XRD) was used to accurately measure the phase stability and lattice parameter as a function of annealing conditions. The diffusion data from each sample was then used to determine self-diffusion coefficients for interdiffusion of the Nb, Zr, and Ta solutes and compared to existing literature values. The minimum annealing conditions to achieve complete chemical homogeneity for each carbide was determined.

nuclear thermal propulsion↗
DOE OSTI2020

Understanding the Deactivation of Ag–ZrO 2 /SiO 2 Catalysts for the Single-step Conversion of Ethanol to Butenes

Ag–ZrO 2 /SBA-16 has recently been found to be efficient for catalyzing the single-step conversion of ethanol to butene (1- and 2-butene mixtures) in the presence of H 2 . The reaction proceeds via a cascading sequence of reactions over mixed metal and Lewis sites, with the catalyst composition tuned to selectively favor butene formation. However, the catalyst slowly deactivates when evaluated over long reaction times. Here, we evaluated the lifetime of the Ag–ZrO 2 /SBA-16 catalyst system for ethanol-to-butene conversion at 325 °C for up to 800 hours on stream. Several characterization techniques were used to elucidate the mechanism(s) by which catalyst deactivation occurs. Coke deposition, Ag particle sintering, and Ag 0 -to-Ag + oxidation state change were identified to be the major causes of catalyst deactivation. Coke deposits cover primarily Lewis acid sites which are responsible for aldol condensation, Meerwein-Ponndorf-Verley (MPV) reduction, and dehydration reactions. Ag particle sintering and Ag oxidation state change leads to a reduction in the number of metallic Ag sites responsible for the dehydrogenation/hydrogenation steps. The fresh catalyst likely experiences hydrothermal sintering in the early stage of reaction and permanently loses some active Lewis acid sites before reaching a new structural steady state. The deactivation of Lewis acid sites leads to a decrease in overall ethanol conversion, whereas the deactivation of the metallic Ag sites decreases the butene selectivity. For catalyst regeneration, oxidative calcination (at 500 °C) followed by reduction (at 325 °C) successfully removes all the coke species on the catalyst surface and restores the metallic Ag particles of the 4Ag–4ZrO 2 /SBA-16 catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Investigation of the Surface Chemistry of Magnesium and Magnesium Alloy Powders

Magnesium (Mg) and Mg alloy powders are generally difficult to sinter at atmospheric pressure in inert atmospheres purportedly due to the presence of powder particle surface oxide layers. To better understand sintering of Mg and Mg alloy powders, x-ray photoelectron spectroscopy (XPS) was performed to characterize the surface chemistry of gas atomized pure Mg and Mg alloys AZ91D and WE43 powders. These results are used to quantitatively determine the surface chemistry of these powders. Additionally, equilibrium thermodynamic modeling of these Mg/Mg alloys materials exposed to oxygen down to part per billion concentrations are presented for relative comparison to experimental XPS results. Analysis of these results are intended to improve sintering of Mg and Mg alloy powder materials through more quantitative knowledge of powder surface chemistry.

25 ENERGY STORAGE↗
DOE OSTI2025

Design, fabrication, simulation, and testing of additively manufactured lattice-based copper heat sinks

Here, this study investigates the potential advantages of lattice structure-based bound metal material extrusion (MEX) 3D printing for fabricating high-performance copper heat sinks. Copper powder-filled polymer filaments, with a copper content of > 90 wt.%, were developed specifically for the bound metal MEX 3D printing process. Three types of structures—planar, strut, and surface lattices—were 3D printed to facilitate efficient heat transfer pathways within the heat sinks. Subsequent post-processing steps, including polymer removal and sintering, were performed to achieve dense copper parts. Hot isostatic pressing was further employed to enhance the sintered density from 93 to 98%. Finite element analysis (FEA) simulations were conducted to assess the heat transfer efficiency of the designs, and heat transfer experiments were performed using a custom setup to validate the simulation results. Additionally, this research explores the use of extended hold times during pre-sintering and a reduced atmosphere to enhance the %IACS values (electrical conductivity) and thermal performance of the bound metal MEX 3D printed copper heat sinks. The investigation combines experimental analysis, including simulations and heat transfer experiments, to gain insights into the structure-material property relationships and optimize the thermal performance of the printed heat sinks.

Ajjarapu, Kameswara Pavan Kumar [Oak Ridge Nationa↗
DOE OSTI2024

Predictive binder jet additive manufacturing enabled by clean burn-off binder design

Binder jet additive manufacturing (BJAM) presents an avenue for advanced manufacturing of various high-value materials due to high deposition rates, scalability, and geometric flexibility. However, conventional organic binders in BJAM introduce residual carbon upon pyrolysis, often leading to imprecise alloy composition in the final sintered part. The undesirable residual carbon from binder burn-off limits the application of BJAM for high-performance alloys due to their high sensitivity to carbon addition. In this study, we have designed poly(vinylpyrrolidone-co-vinyl acetate) (PVP-VAc) as a clean burn-off binder for BJAM, where excess oxygen groups in VAc enable cleaner burn-off and reduce residual carbon retention. Compared to a widely used commercial binder, the optimized PVP-VAc binder reduced residual carbon retention by over 90% in H13 tool steel. The significant reduction in residual carbon enables predictable printing and subsequent sintering of complex H13 tool steel geometries, an alloy known to have substantial challenges around distortion due to the sintering window shifting from carbon addition. The design of a clean burnout binder provides a major path forward for BJAM by enabling new AM designs and applications for composition-sensitive high-performance alloys, such as nickel-based superalloys, titanium alloys, and high alloyed steels.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Zirconium-diboride silicon-carbide composites: A review

Zirconium diboride (ZrB 2 ) and silicon carbide (SiC) composites have long been of interest since it was observed that ZrB 2 improved the thermal shock resistance of SiC. However, processing of these materials can be difficult due to high and different sintering temperatures and differences in the thermodynamic stability of each material. ZrB 2 –SiC composites have been processed in a variety of ways including hot-pressing, spark-plasma sintering, reactive melt infiltration, pack cementation, chemical vapor deposition, chemical vapor infiltration, stereolithography, direct ink writing, selective laser sintering, electron beam melting, and binder jet additive manufacturing. Each manufacturing method has its own pros and cons. This review serves to summarize more than 60 years of research and provide a coherent resource for the variety of methods and advancements in development of ZrB 2 –SiC composites.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The effect of Ni doping on the mechanical behavior of tungsten

The effect of nickel (Ni) on activated sintering of tungsten has been known and investigated for decades. However, there are few reports on the mechanical properties of tungsten when Ni is added as a low alloying additive with less than 1 wt%. In this work, the mechanical behaviors of tungsten doped with 0.2–1.0 wt% nickel from room temperature up to 400 °C were investigated. The results show that the compression ductility of as-sintered Ni doped tungsten is drastically higher than that of as-sintered pure tungsten at all tested temperatures including room temperature, and the fracture toughness at room temperature is increased by 92%. The results suggest that the ductile-to-brittle transition temperature (DBTT) of tungsten can be reduced substantially by doping with Ni.

36 MATERIALS SCIENCE↗