Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “reverse rates”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
NASA NTRS2006

A Novel Lithium-ion Laminated Pouch Cell Tested For Performance And Safety

A new Li-ion 4.0 Ah pouch cell from GS Yuasa has been tested to determine its performance and safety. The cell is of a laminate pouch design with liquid electrolyte. The rate, thermal and vacuum performance capabilities have been tested to determine the optimum parameters. Under vacuum conditions, the cells were cycled under restrained and unrestrained configurations. The burst pressure of the laminate pouch was also determined. The overcharge, overdischarge into reversal and external short circuit safety tests were also performed to determine the cell s tolerance to abuse. Key Words: Li-ion, safety, vacuum test, abuse, COTS batteries, rate capability

Jeevarajan, Judith A.↗
NASA NTRS1978

NASA Pioneer: Venus reverse playback telemetry program TR 78-2

During the entry of the Pioneer Venus Atmospheric Probes into the Venus atmosphere, there were several events (RF blackout and data rate changes) which caused the ground receiving equipment to lose lock on the signal. This caused periods of data loss immediately following each one of these disturbing events which lasted until all the ground receiving units (receiver, subcarrier demodulator, symbol synchronizer, and sequential decoder) acquired lock once more. A scheme to recover these data by off-line data processing was implemented. This scheme consisted of receiving the S band signals from the probes with an open loop reciever (requiring no lock up on the signal) in parallel with the closed loop receivers of the real time receiving equipment, down converting the signals to baseband, and recording them on an analog recorder. The off-line processing consisted of playing the analog recording in the reverse direction (starting with the end of the tape) up, converting the signal to S-band, feeding the signal into the "real time" receiving system and recording on digital tape, the soft decisions from the symbol synchronizer.

Modestino, J. W.↗
DOE OSTI2014

Microstructure evolution of Li uptake/removal in MoO{sub 2}@C nanoparticles with high lithium storage performance

Highlights: • The carbon-coated MoO{sub 2} (MoO{sub 2}@C) ultra fine nanoparticles are synthesized by one-pot hydrothermal method. • MoO{sub 2}@C nanoparticles have high specific capacity, excellent cycling performance and rate performance. • Phase transformations for lithium ion uptake/removal are examined carefully by TEM. • Phase transformations are highly reversible during the redox process. - Abstract: A facile one pot strategy of a hydrothermal methodology was applied to synthesize the carbon coated MoO{sub 2} (MoO{sub 2}@C) nanostructured particles, which are composed of ultra fine nanoparticles with homogeneous carbon coating about several nanometers. As an electrode in lithium ion batteries, the MoO{sub 2}@C shows a high specific capacity and reversible capacity (730 mA h g{sup −1} after 60 cycles). Microstructure investigations, by using a high resolution transmission electron microscopy, of the MoO{sub 2}@C based electrodes employed at various states during the first discharge/charge cycle were conducted to elucidate the lithium ion uptake/removal mechanism and cycling behavior. In the lithium uptake process, the original MoO{sub 2} phase transfers into Li{sub 0.98}MoO{sub 2} through an addition type reaction, and then nanosized metallic Mo emerges as a result of a conversion reaction. In turn, Mo could be oxidized to the intermediate Li{sub 0.98}MoO{sub 2} before converting to hyperfine MoO{sub 2} phase on upcoming lithium removal process.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Polymer Precursor Derived Li x PON Electrolytes: Toward Li–S Batteries

Efforts to develop polymer precursor electrolytes that offer properties anticipated to be similar or superior to (lithium phosphorus oxynitride, LiPON) glasses are reported. Such precursors offer the potential to be used to process LiPON-like thin glass/ceramic coatings for use in all solid state batteries, ASBs. Here, LiPON glasses provide a design basis for the synthesis of sets of oligomers/polymers by lithiation of OP(NH 2 ) 3–x (NH) x [from OP(NH) 3 ],OP(NH 2 ) 3-x (NHSiMe 3 ) x and [P=N] 3 (NHSiMe 3 ) 6–x (NH) x . Furthermore, the resulting systems have degrees of polymerization of 5–20. Treatment with selected amounts of LiNH 2 provides varying degrees of lithiation and Li + conducting properties commensurate with Li + content. Polymer electrolytes impregnated in/on Celgard exhibit Li + conductivities up to ~1 × 10 –5 S cm –1 at room temperature and are thermally stable to ~150 °C. A Li–S battery assembled using a Li 6 SiPON composition polymer electrolyte exhibits an initial reversible capacity of 1500 mAh g sulfur –1 and excellent cycle performance at 0.25 and 0.5 C rate over 120 cycles at room temperature.

25 ENERGY STORAGE↗
DOE OSTI2024

Low-Temperature Molten Salt Electrochemical CO 2 Upcycling for Advanced Energy Materials

One strategy for addressing the climate crisis caused by CO 2 emissions is to efficiently convert CO 2 to advanced materials suited for green and clean energy technology applications. Porous carbon is widely used as an advanced energy storage material because of its enhanced energy storage capabilities as an anode. Herein, we report electrochemical CO 2 upcycling to solid carbon with a controlled microstructure and porosity in a ternary molten carbonate melt at 450 °C. Controlling the electrochemical parameters (voltage, temperature, cathode material) enabled the conversion of CO 2 to porous carbon with a tunable morphology and porosity for the first time at such a low temperature. Additionally, a well-controlled morphology and porosity are beneficial for reversible energy storage. In fact, these carbon materials delivered high specific capacity, stable cycling performances, and exceptional rate capability even under extremely fast charging conditions when integrated as an anode in lithium-ion batteries (LIBs). In conclusion, the present approach not only demonstrated efficient upcycling of CO 2 into porous carbon suitable for enhanced energy storage but can also contribute to a clean and green energy technology that can reduce carbon emissions to achieve sustainable energy goals.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2018

Energy Efficient Formaldehyde Synthesis by Direct Hydrogenation of Carbon Monoxide in Functionalized Metal–Organic Frameworks

Formaldehyde (CH 2 O) is a highly versatile platform chemical with an annual production of over 30 megatons. The current most widely used industrial method for formaldehyde synthesis is very energy intensive and plagued with significant exergy losses. We propose a highly efficient heterogeneous nanoporous catalyst capable of direct hydrogenation of CO to CH 2 O followed by condensation of CH 2 O from a mixture of CO and H 2 , which are non-condensable gases. The key to this synthesis is a Lewis Pair (LP) functionalized metal-organic framework (MOF) heterogeneous porous catalyst. We have computed reaction pathways, barriers, and uncertainties for CO hydrogenation on a LP functionalized MOF using various density functional theory (DFT) methods and high-level ab initio methods. We have assessed the uncertainties in the energetics inherent in the DFT functionals. Here, we predict that the thermodynamics of CH 2 O synthesis will be enhanced relative to gas phase synthesis and more importantly, will not be equilibrium limited because the barrier to product desorption from the MOF is much lower than the barrier for the reverse reaction. Hence, the product will be continuously removed from the process, facilitating very high overall conversion rates. Our proposed process will dramatically improve the sustainability of CH 2 O synthesis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Active site design enables industrial scale H 2 O 2 electrosynthesis with metal-free catalysts

The electrosynthesis of hydrogen peroxide (H 2 O 2 ) via a two-electron oxygen reduction reaction enables decentralized H 2 O 2 production. While metal-free carbon catalysts are sustainable and low-cost, their performance is hindered by poorly defined active sites and uncontrolled defect states. Here, we resolve these challenges through active site design and catalyst screening using fluorine (F) and nitrogen (N) codoped carbons as model materials. Statistical analysis combined with density functional theoretical calculations reveals that F-induced structural modification and defect passivation optimize OOH* binding, with F-doping and adjacent F atoms predominantly lowering abs ΔG(OOH*). Experimental results confirm that semi-ionic C–F bonds passivate defects in nitrogen-doped carbon, enhancing catalytic activity and durability. The resulting (N, F)-codoped carbon achieves nearly 100% H 2 O 2 selectivity at 0.5–0.65 V versus the reversible hydrogen electrode and maintains > 95% across 0.01–0.65 V versus the reversible hydrogen electrode. In an electrolyzer, (N, F)-codoped carbon exhibits an H 2 O 2 yield rate of 74.35 mol g cat. −1 h -1 and sustains 300 mA cm -2 for 105 hours with ~95% faradaic efficiency. Coupling the two-electron oxygen reduction reaction with methanol oxidation further reduces cell voltage and enhances productivity. This work provides a means to design efficient catalysts for industrial H 2 O 2 electrosynthesis.

H2O2 electrosynthesis↗
DOE OSTI2021

Fictitious phase separation in Li layered oxides driven by electro-autocatalysis

Layered oxides widely used as lithium-ion battery electrodes are designed to be cycled under conditions that avoid phase transitions. Although the desired single-phase composition ranges are well established near equilibrium, operando diffraction studies on many-particle porous electrodes have suggested phase separation during delithiation. Notably, the separation is not always observed, and never during lithiation. These anomalies have been attributed to irreversible processes during the first delithiation or reversible concentration-dependent diffusion. However, these explanations are not consistent with all experimental observations such as rate and path dependencies and particle-by-particle lithium concentration changes. Here, we show that the apparent phase separation is a dynamical artefact occurring in a many-particle system driven by autocatalytic electrochemical reactions, that is, an interfacial exchange current that increases with the extent of delithiation. We experimentally validate this population-dynamics model using the single-phase material L ix (Ni 1/3 Mn 1/3 Co 1/3 )O 2 (0.5 < x < 1) and demonstrate generality with other transition-metal compositions. Operando diffraction and nanoscale oxidation-state mapping unambiguously prove that this fictitious phase separation is a repeatable non-equilibrium effect. We quantitatively confirm the theory with multiple-datastream-driven model extraction. More generally, our study experimentally demonstrates the control of ensemble stability by electro-autocatalysis, highlighting the importance of population dynamics in battery electrodes (even non-phase-separating ones).

36 MATERIALS SCIENCE↗
DOE OSTI2015

High-performance symmetric sodium-ion batteries using a new, bipolar O3-type material, Na 0.8 Ni 0.4 Ti 0.6 O 2

Based on low-cost and rich resources, sodium-ion batteries have been regarded as a promising candidate for next-generation energy storage batteries in the large-scale energy applications of renewable energy and smart grids. However, there are some critical drawbacks limiting its application, such as safety and stability problems. In this work, a stable symmetric sodium-ion battery based on the bipolar, active O3-type material, Na0.8Ni0.4Ti0.6O2, is developed. This bipolar material shows a typical O3-type layered structure, containing two electrochemically active transition metals with redox couples of Ni4+/Ni2+ and Ti4+/Ti3+, respectively. This Na0.8Ni0.4Ti0.6O2-based symmetric cell exhibits a high average voltage of 2.8 V, a reversible discharge capacity of 85 mA h g(-1), 75% capacity retention after 150 cycles and good rate capability. This full symmetric cell will greatly contribute to the development of room-temperature sodium-ion batteries with a view towards safety, low cost and long life, and it will stimulate further research on symmetric cells using the same active materials as both cathode and anode.

Guo, Shaohua↗
DOE OSTI2014

Correlation of anomalous write error rates and ferromagnetic resonance spectrum in spin-transfer-torque-magnetic-random-access-memory devices containing in-plane free layers

In a small fraction of magnetic-tunnel-junction-based magnetic random-access memory devices with in-plane free layers, the write-error rates (WERs) are higher than expected on the basis of the macrospin or quasi-uniform magnetization reversal models. In devices with increased WERs, the product of effective resistance and area, tunneling magnetoresistance, and coercivity do not deviate from typical device properties. However, the field-swept, spin-torque, ferromagnetic resonance (FS-ST-FMR) spectra with an applied DC bias current deviate significantly for such devices. With a DC bias of 300 mV (producing 9.9 × 10{sup 6} A/cm{sup 2}) or greater, these anomalous devices show an increase in the fraction of the power present in FS-ST-FMR modes corresponding to higher-order excitations of the free-layer magnetization. As much as 70% of the power is contained in higher-order modes compared to ≈20% in typical devices. Additionally, a shift in the uniform-mode resonant field that is correlated with the magnitude of the WER anomaly is detected at DC biases greater than 300 mV. These differences in the anomalous devices indicate a change in the micromagnetic resonant mode structure at high applied bias.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2015

Effect of proton irradiation energy on AlGaN/GaN metal-oxide semiconductor high electron mobility transistors

The effects of proton irradiation energy on dc characteristics of AlGaN/GaN metal-oxide semiconductor high electron mobility transistors (MOSHEMTs) using Al 2 O 3 as the gate dielectric were studied. Al 2 O 3 /AlGaN/GaN MOSHEMTs were irradiated with a fixed proton dose of 5 × 10 15 cm -2 at different energies of 5, 10, or 15 MeV. More degradation of the device dc characteristics was observed for lower irradiation energy due to the larger amount of nonionizing energy loss in the active region of the MOSHEMTs under these conditions. The reductions in saturation current were 95.3%, 68.3%, and 59.8% and reductions in maximum transconductance were 88%, 54.4%, and 40.7% after 5, 10, and 15 MeV proton irradiation, respectively. Both forward and reverse gate leakage current were reduced more than one order of magnitude after irradiation. The carrier removal rates for the irradiation energies employed in this study were in the range of 127–289 cm -1 . These are similar to the values reported for conventional metal-gate high-electron mobility transistors under the same conditions and show that the gate dielectric does not affect the response to proton irradiation for these energies.

36 MATERIALS SCIENCE↗
NASA NTRS1973

Fast recharge circuit for q-switched lasers

Cavity-dumped lasers employ electrooptic-effect cell to alternately block and release laser pulse. Cell requires high-speed switching circuit that can apply and remove high voltage. Solid-state circuit employs complementary transistor switches which can switch at rates greater than 5 kHz, eliminate warmup time, provide variable voltage wave-form, and allow polarity reversal.

Hansen, R. L.↗
NASA NTRS1973

Friction, wear, and transfer of carbon and graphite to copper, chromium, and aluminum metal surfaces in vacuum

Sliding friction experiments were conducted with amorphous and fully graphitized carbons sliding on copper and on films of chromium and aluminum on copper. Auger emission spectroscopy analysis was used to monitor carbon transfer to the metal surfaces. Friction and wear were also measured. Metal surfaces were examined both in the clean state and with normal oxides present. Results indicate that different metals have an important effect on friction, wear, and transfer characteristics. With amorphous carbon, the least chemically active metal gave the highest wear and amount of carbon transfer. Both forms of carbon gave lower friction and wear and lower transfer rates when in contact with clean, as opposed to oxide-covered, chromium surfaces. With copper, the reverse was true; cleaning was detrimental.

Buckley, D. H.↗
NASA NTRS1980

An SCR inverter for electric vehicles

An inverter for an electric vehicle propulsion application has been designed and constructed to excite a polyphase induction motor from a fixed propulsion battery source. The inverter, rated at 35kW peak power, is fully regenerative and permits vehicle operation in both the forward and reverse directions. Thyristors are employed as the power switching devices arranged in a dc bus commutated topology. This paper describes the major role the controller plays in generating the motor excitation voltage and frequency to deliver performance similar to dc systems. Motoring efficiency test data for the controller are presented. It is concluded that an SCR inverter in conjunction with an ac induction motor is a viable alternative to present dc vehicle propulsion systems on the basis of performance and size criteria.

Latos, T.↗
NASA NTRS1980

Changes in cardiac output and tibial artery flow during and after progressive LBNP

A 3.0 MHz Pulsed Doppler velocity meter (PD) was used to determine blood velocities in the ascending aorta from the suprasternal notch before, during and after progressive 5 min stages of lower body negative pressure (LBNP) in 7 subjects. Changes in stroke volume were calculated from the systolic velocity integrals. A unique 20 MHz PD was used to estimate bloodflow in the posterior tibial artery. With -20 torr mean stroke volume fell 11% and then continued to decline by 48% before LBNP was terminated. Mean tibial flow fell progressively with LBNP stress, due to an increase in reverse flow component and a reduction in peak forward flow and diameter. Stroke volume increased and heart rate fell dramatically during the first 15 sec of recovery. The LBNP was terminated early in 2 subjects because of vasovagal symptons (V). During V the stroke volume rose 86% which more than compensated for the drop in heart rate. This implies that V is accompanied by a paradoxical increase in venous return and that the reduction in HR is the primary cardiovascular event. During the first 15 sec of recovery these 2 subjects had a distinctive marked rise to heart rate reminiscent of the Bainbridge reflex.

Source record↗
DOE OSTI2021

Adiabatic quantum decoherence in many non-interacting subsystems induced by the coupling with a common boson bath

Highlights: • System–environment quantum correlation: a main solid state NMR decoherence channel. • Non-separable system–environment model yields realistic spin decoherence rates. • New open quantum system approach explains irreversible decay of refocused NMR echoes. • Adiabatic quantum decoherence is inherently irreversible and eigen-selective. This work addresses adiabatic quantum decoherence of many-body spin systems coupled with a boson field in the framework of open quantum systems theory. We generalize the traditional spin-boson model by considering a system–environment interaction Hamiltonian that represents a partition of non-interacting subsystems and highlights the collective correlation that appears exclusively due to the coupling with a common environment. Remarkably, this simple, exactly solvable model encompasses relevant aspects of a many-body open quantum system and features the subtle quantum effects that arise when the size scales up to a macroscopic level. We derive an analytical expression for the time dependence of the density matrix elements (in the preferred basis) without assuming coarse-graining. The resulting decoherence function is eigen-selective and is a complex exponential whose exponent has a real part that introduces a decay similar to that in the spin-boson model. On the contrary, the imaginary part depends on the quantum numbers and geometry of the whole partition and does not reflect the system temperature. Motivated by decoherence in solid-state NMR, and in search of realistic numerical estimations, we apply the theoretical results to a partition of dipole-coupled spin pairs in contact with a common phonon bath, using typical parameters of hydrated salts. The proposal allows estimating the decoherence time scale in terms of the system physical constants: sound velocity and eigenvalue distribution width. As a significant novelty, the decoherence function phase depends on the eigenvalue distribution throughout the sample. It plays the leading role, overshadowing the mechanism associated with the bath thermal state. Finally, we apply the formalism to describe decoherence in the “magic echo” NMR reversal experiment. We find that the system–environment correlation explains the origin of irreversibility, and both the decoherence rate value and its dependence on the dipolar frequency, are remarkably similar to the experiment.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2013

IMPLEMENTING PRIMARY CREEP CALCULATIONS DURING STRESS CHANGES AND REVERSALS IN THE FUEL PERFORMANCE CODE FRAPCON-3

Recently, the creep models in FRAPCON-3.4 were used to model the creep tests performed in IFA-699 up through cycle 4. IFA-699 is an instrumented test rig in the Halden Boiling Water Reactor that is being used to perform in-reactor creep experiments under changing stress conditions. The cladding creep tests in IFA-699 were on four fresh fuel segments with Zircaloy-4, E110, M-MDA, and M5™ cladding. These fuel segments were loaded in a test rig and placed in a PWR loop and operated under PWR conditions. Each of the test fuel rods were connected to gas lines in order to apply tensile and compressive stresses to the cladding. Diameters of the cladding were measured by diameter gages at several intervals to measure the creep behavior of the cladding as a function of time. The creep tests were performed at a temperature of around 360°C and fast neutron flux of 1.8 to 2.4×1017 n/m²-s (depends on specimen location). During the four cycles of operation, hoop stresses of -75, -50, +30, and +110 MPa were applied to the specimens. In addition to providing assessment of the FRAPCON-3.4 creep modeling, the creep model comparisons were also used to provide insight into the nature of primary creep following stress changes, whether creep behavior is symmetric under tensile and compressive loading, and the effect of fast fluence on creep rate. It was determined that creep strain should be calculated as a function of effective stress rather than hoop stress. This accounts for the observed difference between creep under compressive and tensile stress for the same hoop stress. It was also determined that the primary creep changes in proportion to the change in stress following stress change or stress reversal. Finally, it was observed that the irradiation creep rate decreases somewhat with increasing fluence. The creep model in FRAPCON-3.4 has already been developed to be a function of effective stress and includes a term that decreases the irradiation creep rate with increasing fluence. A new mathematical formulation has been developed that is suitable for a fuel performance code to calculate the primary creep strain under conditions of changing stress and stress reversal. The creep model in FRAPCON-3.4 and the formulation for calculating primary creep under changing stress conditions will be described in this paper. Comparisons to data will also be provided.

Geelhood, Kenneth J.↗
NASA NTRS1993

Performance of the unique-word-reverse-modulation type demodulator for mobile satellite communications

This paper proposes a new type of coherent demodulator, the unique-word (UW)-reverse-modulation type demodulator, for burst signal controlled by voice operated transmitter (VOX) in mobile satellite communication channels. The demodulator has three individual circuits: a pre-detection signal combiner, a pre-detection UW detector, and a UW-reverse-modulation type demodulator. The pre-detection signal combiner combines signal sequences received by two antennas and improves bit energy-to-noise power density ratio (E(sub b)/N(sub 0)) 2.5 dB to yield 10(exp -3) average bit error rate (BER) when carrier power-to-multipath power ratio (CMR) is 15 dB. The pre-detection UW detector improves UW detection probability when the frequency offset is large. The UW-reverse-modulation type demodulator realizes a maximum pull-in frequency of 3.9 kHz, the pull-in time is 2.4 seconds and frequency error is less than 20 Hz. The performances of this demodulator are confirmed through computer simulations and its effect is clarified in real-time experiments at a bit rate of 16.8 kbps using a digital signal processor (DSP).

Dohi, Tomohiro↗