Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “resistivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

Non-Magnetic, Tough, Corrosion- and Wear-Resistant Knives From Bulk Metallic Glasses and Composites

Quality knives are typically fabricated from high-strength steel alloys. Depending on the application, there are different requirements for mechanical and physical properties that cause problems for steel alloys. For example, diver's knives are generally used in salt water, which causes rust in steel knives. Titanium diver's knives are a popular alternative due to their salt water corrosion resistance, but are too soft to maintain a sharp cutting edge. Steel knives are also magnetic, which is undesirable for military applications where the knives are used as a tactical tool for diffusing magnetic mines. Steel is also significantly denser than titanium (8 g/cu cm vs. 4.5 g/cu cm), which results in heavier knives for the same size. Steel is hard and wear-resistant, compared with titanium, and can keep a sharp edge during service. A major drawback of both steel and titanium knives is that they must be ground or machined into the final knife shape from a billet. Since most knives have a mirrored surface and a complex shape, manufacturing them is complex. It would be more desirable if the knife could be cast into a net or near-net shape in a single step. The solution to the deficiencies of titanium, steel, and ceramic knives is to fabricate them using bulk metallic glasses (or composites). These alloys can be cast into net or near-net shaped knives with a combination of properties that exceed both titanium and steel. A commercially viable BMG (bulk metallic glass) or composite knife is one that exhibits one or all of the following properties: It is based on titanium, has a self-sharpening edge, can retain an edge during service, is hard, is non-magnetic, is corrosion-resistant against a variety of corrosive environments, is tough (to allow for prying), can be cast into a net-shape with a mirror finish and a complex shape, has excellent wear resistance, and is low-density. These properties can be achieved in BMG and composites through alloy chemistry and processing. For each desired property for knife fabrication and performance, there is an alloy development strategy that optimizes behavior. Although BMG knives have been demonstrated as far back as 1995, they never found commercial success because they had to be ground (which presented problems because the alloys contained beryllium), they weren't low cost (because they weren't cast to a net-shape), they were brittle (because they were made with a low-quality commercial material), and they had extremely poor corrosion resistance (because corrosion was not well-understood in these materials). Ultimately, these shortcomings prevented the widespread commercialization. In the current work, the inventors have applied more than a decade of research on BMGs from Caltech and JPL to develop a better understanding of how to make BMG knives that exhibit an optimal combination of properties, processing and cost. Alloys have been developed based in titanium (and other metals), that exhibit high toughness, high hardness, excellent corrosion resistance, no ferromagnetism, edge-retaining selfsharpening, and the ability to be cast like a plastic using commercially available casting techniques (currently used by commercial companies such as Liquidmetal Technologies and Visser Precision Casting). The inventors argue that depending on the application (diving, military, tactical, utility, etc.) there is an optimal combination of design and alloy composition. Moreover, with new casting technologies not available at the inception of these materials, net-shaped knives can be cast into complex shapes that require no aftermarket forming, except for sharpening using water-cooled polishing wheel. These combinations of discoveries seek to make low-cost BMG knives commercially viable products that have no equal among metal or ceramic knives. Current work at JPL focuses on net-shape casting of these alloys and testing their mechanical properties versus commercially available knives to demonstrate their benefits.

Hoffman, Douglas C.↗

Enterococci in Space: Adaptation, Antibiotic Resistance, and Clinical Implications

Enterococci are gram-positive bacteria that originated when our ancient animal ancestors emerged from the oceans to live on land, and brought their gut flora with them. Enterococcus faecalis (EF) and Enterococcus faecium, are common human commensals and can harbor multidrug resistance. Both have been previously isolated from the International Space Station (ISS). Likely as a consequence of their evolutionary origins, enterococci show remarkable stress resistance within, but also outside, their human hosts. Their antibiotic resistance, coupled with tolerance to desiccation, starvation, and disinfection, make some EF strains potent pathogens in the built environment (e.g., hospitals), and a potential risk to crew health during space missions. Here we describe our planned flight studies, currently in development. Genomic Enumeration of Antibiotic Resistance in Space (GEARS) will characterize the frequency and genomic identity of antibiotic resistant organisms, including enterococci, on the ISS, and expand our future in-space sequencing-based diagnostic capabilities. Enterococcus Growth Advantage on ISS via Tn-seq (EnteroGAIT) will assess the evolutionary selective pressure of the space environment (microgravity, space radiation) using EF as a model system during a long-duration culture and persistence experiment. Adaptation & Evolution of Resilient Enterococcus in Space (AERES) will study existing and newly identified isolates to characterize the “natural” evolutionary history of EF on Earth and in space to reveal mechanisms of microbial adaption including, possibly, natural selection. Our work to date has identified that EF ISS isolates share virulence factors found in clinical strains and commensals, and revealed limitations of current pathogenicity assessment tools. While ISS isolates were, in some cases, multi-drug resistant, current data suggests these are largely commensal strains. Our work will further refine potential crew health risks and improve understanding of EF adaptation to the built environment, of great relevance on Earth where EF is the second leading cause of hospital acquired infection.

Jordan McKaig↗

The Structural Bases of Antibiotic Resistance in the Clinically Derived Mutant beta-Lactamases TEM-30, TEM-32, and TEM-34

Widespread use of {beta}-lactam antibiotics has promoted the evolution of {beta}-lactamase mutant enzymes that can hydrolyze ever newer classes of these drugs. Among the most pernicious mutants are the inhibitor-resistant TEM {beta}-lactamases (IRTs), which elude mechanism-based inhibitors, such as clavulanate. Despite much research on these IRTs, little is known about the structural bases of their action. This has made it difficult to understand how many of the resistance substitutions act as they often occur far from Ser-130. Here, three IRT structures, TEM-30 (R244S), TEM-32 (M69I/M182T), and TEM-34 (M69V), are determined by x-ray crystallography at 2.00, 1.61, and 1.52 {angstrom}, respectively. In TEM-30, the Arg-244 {yields} Ser substitution (7.8 {angstrom} from Ser-130) displaces a conserved water molecule that usually interacts with the {beta}-lactam C3 carboxylate. In TEM-32, the substitution Met-69 {yields} Ile (10 {angstrom} from Ser-130) appears to distort Ser-70, which in turn causes Ser-130 to adopt a new conformation, moving its O{gamma} further away, 2.3 {angstrom} from where the inhibitor would bind. This substitution also destabilizes the enzyme by 1.3 kcal/mol. The Met-182 {yields} Thr substitution (20 {angstrom} from Ser-130) has no effect on enzyme activity but rather restabilizes the enzyme by 2.9 kcal/mol. In TEM-34, the Met-69 {yields} Val substitution similarly leads to a conformational change in Ser-130, this time causing it to hydrogen bond with Lys-73 and Lys-234. This masks the lone pair electrons of Ser-130 O{gamma}, reducing its nucleophilicity for cross-linking. In these three structures, distant substitutions result in accommodations that converge on the same point of action, the local environment of Ser-130. TEM-1 {beta}-lactamase is the predominant source of resistance to {beta}-lactams, such as the penicillins. TEM-1 and related class A {beta}-lactamases confer resistance by hydrolyzing the {beta}-lactam ring of these antibiotics; bacteria expressing these enzymes have become widespread in hospitals and in the community. Beginning in 1980s, three mechanism-based class A {beta}-lactamase inhibitors, clavulanate, tazobactam, and sulbactam, have been used in combination with conventional penicillins to reverse this resistance (Fig.1, A-C). However, since 1992, more than 26 so-called inhibitor-resistant TEM (IRT)1 mutants have been selected, reversing susceptibility to these three mechanism-based inhibitors in the clinic (www.lahey.org/studies/temtable.stm).

08 HYDROGEN↗

Dynamic Resistance of YBCO-Coated Conductors in Applied AC Fields with DC Transport Currents and DC Background Fields

In order to predict heat loads in future saturable core fault-current-limiting devices due to ac fringing fields, dynamic resistance in YBCO-coated conductors was measured at 77 K in peak ac fields up to 25 mT at 60 Hz and in dc fields up to 1 T. With the sample orientation set such that the conductor face was either parallel or perpendicular to the ac and dc applied fields, the dynamic resistance was measured at different fractions of the critical current to determine the relationship between the dc transport current and the applied fields. With respect to field orientation, the dynamic resistance for ac fields that were perpendicular to the conductor face was significantly higher than when the ac fields were parallel to the conductor face. It was also observed that the dynamic resistance: (1) increased with increasing fraction of the dc transport current to the critical current, (2) was proportional to the inverse of the critical current, and (3) demonstrated a linear dependence with the applied ac field once a threshold field was exceeded. This functional behavior was consistent with a critical state model for the dynamic resistance, but discrepancies in absolute value of the dynamic resistance suggested that further theoretical development is needed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Gaseous dry deposition of atmospheric mercury: A comparison of two surface resistance models for deposition to semiarid vegetation

In the United States, atmospheric mercury (Hg) deposition, from regional and international sources, is the largest contributor to increased Hg concentrations in bodies of water leading to bioaccumulation of methyl mercury in fish. In this work, modeled dry deposition velocities (vd) for gaseous Hg are calculated using two surface resistance parameterizations found in the literature. The flux is then estimated as the product of the species concentration and modeled vd. The calculations utilize speciated atmospheric mercury concentrations measured during an annual monitoring campaign in southern Idaho. Gaseous elemental mercury (GEM) and reactive gaseous mercury (RGM) were monitored with Tekran models 2537A and 1130, respectively. Two anemometers collected meteorological data, including one fast-response three-dimensional sonic anemometer to measure turbulence parameters. For the flux calculation, three resistances are required to model the mechanisms that transport gaseous Hg from the atmosphere to the surface, with the surface resistance being the largest source of error. Results from two surface resistance models are presented. In particular, the downward flux is sensitive to the choice of model and input parameters such as seasonal category and mesophyll resistance. A comparison of annual GEM and RGM fluxes calculated using the two models shows good agreement for RGM (3.2% difference for annual deposition); however, for the low-solubility species of GEM, the models show a 64% difference in annual fluxes, with a range of 32% to 200% in seasonal fluxes. Results indicate the importance of understanding the diurnal variation of the physical processes modeled in the surface resistance parameterization for vd.

54 ENVIRONMENTAL SCIENCES↗

Remote sensing of freeze-thaw transitions in Arctic soils using the complex resistivity method

Our ability to monitor freeze - thaw transitions is critical to developing a predictive understanding of biogeochemical transitions and carbon dynamics in high latitude environments. In this study, we conducted laboratory column experiments to explore the potential of the complex resistivity method for monitoring the freeze - thaw transitions of the arctic permafrost soils. Samples for the experiment were collected from the upper active layer of Gelisol soils at the Barrow Environmental Observatory, Barrow Alaska. Freeze - thaw transitions were induced through exposing the soil column to controlled temperature environments at 4 C and -20 C. Complex resistivity and temperature measurements were collected regularly during the freeze - thaw transitions using electrodes and temperature sensors installed along the column. During the experiments, over two orders of magnitude of resistivity variations were observed when the temperature was increased or decreased between -20 C and 0 C. Smaller resistivity variations were also observed during the isothermal thawing or freezing processes that occurred near 0 C. Single frequency electrical phase response and imaginary conductivity at 1 Hz were found to be exclusively related to the unfrozen water in the soil matrix, suggesting that these geophysical 24 attributes can be used as a proxy for the monitoring of the onset and progression of the freeze - thaw transitions. Spectral electrical responses and fitted Cole Cole parameters contained additional information about the freeze - thaw transition affected by the soil grain size distribution. Specifically, a shift of the observed spectral response to lower frequency was observed during isothermal thawing process, which we interpret to be due to sequential thawing, first from fine then to coarse particles within the soil matrix. Our study demonstrates the potential of the complex resistivity method for remote monitoring of freeze - thaw transitions in arctic soils. Although conducted at the laboratory scale, this study provides the foundation for exploring the potential of the complex resistivity signals for monitoring spatiotemporal variations of freeze - thaw transitions over field-relevant scales.

climate↗

Fast, Accurate, and Reliable Thermal Metrology to Assess the Thermal Resistivity on Small Samples of Thermal Insulation

Developing new insulation materials having a thermal resistivity greater than 69 m K/W (10 hr ft2 °F/Btu/inch) can be appealing for building envelope retrofit and construction of new buildings. Multiple institutions are involved in the development of innovative insulation materials with high thermal resistivity. However, these projects have struggled in the development of new materials due to the difficulty associated with the measurement of small sections of high thermal resistivity materials. As new materials are being developed, the size of each test specimen impacts the cost of development. Given the lack of a reliable method to measure the thermal resistivity on small samples of such materials, we evaluated experimental techniques that can be improved to satisfy the need for testing small sections of high thermal resistivity materials and developed standardized test methods to enable the rapid thermal evaluation of advanced insulation materials. This paper presents the study results and potential techniques for fast, accurate, and reliable effective thermal resistivity measurement on small samples of insulation materials.

Desjarlais, Andre Omer↗

Measured values of coal mine stopping resistance

As coal mines become larger, the number of stoppings in the ventilation system increases. Each stopping represents a potential leakage path which must be adequately represented in the ventilation model. Stopping resistance can be calculated using two methods, the USBM method, used to determine a resistance for a single stopping, and the MVS technique, in which an average resistance is calculated for multiple stoppings. Through MVS data collected from ventilation surveys of different subsurface coal mines, average resistances for stoppings were determined for stopping in poor, average, good, and excellent conditions. The calculated average stoppings resistance were determined for concrete block and Kennedy stopping. Using the average stopping resistance, measured and calculated using the MVS method, provides a ventilation modeling tool which can be used to construct more accurate and useful ventilation models. 3 refs., 3 figs.

01 COAL, LIGNITE, AND PEAT↗

In Vitro Resistance Study of AG-021541, a Novel Nonnucleoside Inhibitor of the Hepatitis C Virus RNA-Dependent RNA Polymerase

A novel class of nonnucleoside hepatitis C virus (HCV) polymerase inhibitors characterized by a dihydropyrone core was identified by high-throughput screening. Crystallographic studies of these compounds in complex with the polymerase identified an allosteric binding site close to the junction of the thumb and finger domains, approximately 30 A away from the catalytic center. AG-021541, a representative compound from this series, displayed measurable in vitro antiviral activity against the HCV genotype 1b subgenomic replicon with a mean 50% effective concentration of 2.9 muM. To identify mutations conferring in vitro resistance to AG-021541, resistance selection was carried out using HCV replicon cells either by serial passages in increasing concentrations of AG-021541 or by direct colony formation at fixed concentrations of the compound. We identified several amino acid substitutions in the AG-021541-binding region of the polymerase, including M423(T/V/I), M426T, I482(S/T), and V494A, with M423T as the predominant change observed. These mutants conferred various levels of resistance to AG-021541 and structurally related compounds but remained sensitive to interferon and HCV polymerase inhibitors known to interact with the active site or other allosteric sites of the protein. In addition, dihydropyrone polymerase inhibitors retained activity against replicons that contain signature resistance changes to other polymerase inhibitors, including S282T, C316N, M414T, and P495(S/L), indicating their potential to be used in combination therapies with these polymerase inhibitors. AG-021541-resistant replicon cell lines provide a valuable tool for mechanism-of-action studies of dihydropyrone polymerase inhibitors. The clinical relevance of in vitro resistance to HCV polymerase inhibitors remains to be investigated.

59 BASIC BIOLOGICAL SCIENCES↗

The effect of resist on the transfer of line-edge roughness spatial metrics from mask to wafer

Mask contributors to line-edge roughness (LER) have recently been shown to be an issue of concern for both the accuracy of current resist evaluation tests as well the ultimate LER requirements for the 22-nm production node. More recently, it has been shown that the power spectral density of the mask-induced roughness, is markedly different than that of intrinsic resist roughness and thus potentially serves as a mechanism for distinguishing mask effects from resist effects in experimental results. Further considering stochastic resist effects, however, demonstrates that such a test would only be viable in cases where the resist effects are completely negligible in terms of their contribution to the total LER compared to the mask effects. The results presented here lead us to the surprising conclusion that it is indeed possible for mask contributors to be the dominant source of LER while the spatial characteristics of the LER remain indistinguishable from the fractal characteristics of resist-induced LER.

36 MATERIALS SCIENCE↗

ENVIRONMENTAL MONITORING OF LEAKS USING TIME LAPSED LONG ELECTRODE ELECTRICAL RESISTIVITY

Highly industrialized areas pose challenges for surface electrical resistivity characterization due to metallic infrastructure. The infrastructure is typically more conductive than the desired targets and will mask the deeper subsurface information. These challenges may be minimized if steel-cased wells are used as long electrodes in the area near the target. We demonstrate a method of using long electrodes to electrically monitor a simulated leak from an underground storage tank with both synthetic examples and a field demonstration. The synthetic examples place a simple target of varying electrical properties beneath a very low resistivity layer. The layer is meant to replicate the effects of infrastructure. Both surface and long electrodes are tested on the synthetic domain. The leak demonstration for the field experiment is simulated by injecting a high conductivity fluid in a perforated well within the S tank farm at Hanford, and the resistivity measurements are made before and after the leak test. All data are processed in four dimensions, where a regularization procedure is applied in both the time and space domains. The synthetic test case shows that the long electrode ERM could detect relative changes in resistivity that are commensurate with the differing target properties. The surface electrodes, on the other hand, had a more difficult time matching the original target's footprint. The field results shows a lowered resistivity feature develop south of the injection site after cessation of the injections. The time lapsed regularization parameter has a strong influence on the differences in inverted resistivity between the pre and post injection datasets, but the interpretation of the target is consistent across all values of the parameter. The long electrode ERM method may provide a tool for near real-time monitoring of leaking underground storage tanks.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Scalable Al 2 O 3 –TiO 2 Conductive Oxide Interfaces as Defect Reservoirs for Resistive Switching Devices

Abstract Resistive switching devices herald a transformative technology for memory and computation, offering considerable advantages in performance and energy efficiency. Here, a simple and scalable material system of conductive oxide interfaces is employed, and their unique properties are leveraged for a new type of resistive switching device. An Al 2 O 3 –TiO 2 ‐based valence‐change resistive switching device, where the conductive oxide interface serves both as the bottom electrode and as a reservoir of defects for switching, is demonstrated. The amorphous–polycrystalline Al 2 O 3 –TiO 2 conductive interface is obtained following the technological path of simplifying the fabrication of the 2D electron gases (2DEGs), making them scalable for practical mass integration. Physical analysis of the device chemistry and microstructure with comprehensive electrical analysis of its switching behavior and performance is combined. The origin of the resistive switching is pinpointed to the conductive oxide interface, which serves both as the bottom electrode and as a reservoir of oxygen vacancies. The latter plays a key role in valence‐change resistive switching devices. The new device, based on scalable and complementary metal–oxide–semiconductor (CMOS)‐technology‐compatible fabrication processes, opens new design spaces toward increased tunability and simplification of the device selection challenge.

36 MATERIALS SCIENCE↗

Structure of VanS from vancomycin-resistant enterococci: A sensor kinase with weak ATP binding

The VanRS two-component system regulates the resistance phenotype of vancomycin-resistant enterococci. VanS is a sensor histidine kinase that responds to the presence of vancomycin by autophosphorylating and subsequently transferring the phosphoryl group to the response regulator, VanR. The phosphotransfer activates VanR as a transcription factor, which initiates the expression of resistance genes. Structural information about VanS proteins has remained elusive, hindering the molecular-level understanding of their function. Here, we present X-ray crystal structures for the catalytic and ATP-binding (CA) domains of two VanS proteins, derived from vancomycin-resistant enterococci types A and C. Both proteins adopt the canonical Bergerat fold that has been observed for CA domains of other prokaryotic histidine kinases. We attempted to determine structures for the nucleotide-bound forms of both proteins; however, despite repeated efforts, these forms could not be crystallized, prompting us to measure the proteins' binding affinities for ATP. Unexpectedly, both CA domains displayed low affinities for the nucleotide, with K D values in the low millimolar range. Since these K D values are comparable to intracellular ATP concentrations, this weak substrate binding could reflect a way of regulating expression of the resistance phenotype.

59 BASIC BIOLOGICAL SCIENCES↗

Corrosion resistance of kolsterised austenitic 304 stainless steel

Austenitic stainless suffers from low wear resistance in applications where rubbing against other surfaces is encountered. This drawback can be overcome by surface treatment such as coating by hard materials. Other treatments such as carburization at relatively low temperature become applicable recently to improve hardness and wear resistance. Carburization heat treatment would only be justified if the corrosion resistance is unaffected. In this work samples of 304 stainless steels treated by colossal supersaturation case carburizing (known as Kolsterising) carried out by Bodycote Company was examined for pitting corrosion resistance at room temperature and at 50 °C. Comparison with results obtained for untreated samples in similar testing conditions show that there is no deterioration in the pitting resistance due to the Kolsterising heat treatment. X ray diffraction patterns obtained for Kolsterising sample showed that peaks correspond to the austenite phase has shifted to lower 2θ values compared with those of the untreated sample. The shift is an indication for expansion of austenite unit cells caused by saturation with diffusing carbon atoms. The XRD of Kolsterising samples also revealed additional peaks appeared in the patterns due to formation of carbides in the kolsterised layer. Examination of these additional peaks showed that these peaks are attributed to a type of carbide known as Hagg carbide Fe{sub 2}C{sub 5}. The absence of carbides that contain chromium means that no Cr depletion occurred in the layer and the corrosion properties are maintained. Surface hardness measurements showed large increase after Kolsterising heat treatment.

36 MATERIALS SCIENCE↗

Nanometer-Scale Measurement of Grid Finger Electrical Conduction Pathways to Detect Series Resistance Degradation of Utility-Scale Silicon Solar Cells

Here, we report on an electrical conduction mechanism for series resistance (Rs) degradation observed in a utility-scale photovoltaic power plant by imaging the local resistance at the Ag/Si interface of the c-Si front metallization. Scanning spreading resistance microscopy imaging with nanometer (nm) scale spatial resolution revealed that the number of point or small-area electrical contacts decreased substantially in a degraded cell compared to an unaffected cell, demonstrating the root cause of Rs degradation. The decrease in electrical contacts is likely caused by a structural change - the Ag particles in contact with the Si cell (or via a nm-thickness tunneling glass layer) aggregate into bulk Ag, and a highly resistive glass frit forms a belt shape at the Ag/Si interface. This resistive belt, with a thickness of ~1 um, blocks the current conduction from the cell emitter to the Ag grid. Our microscopy results help to unravel unambiguously the degradation mechanism and demonstrate an example of the multiscale characterization approach for understanding degradation in field-weathered PV module.

14 SOLAR ENERGY↗

Local nm-Scale Imaging of Electrical Contact for Series Resistance Degradation of Silicon Solar Cells

We report on an electrical conduction mechanism for series resistance (Rs) degradation observed in a utility scale solar farm by nm-scale imaging of the local resistance at the Ag/Si interface of c-Si front metallization. Scanning spreading resistance microscopy imaging revealed that the number of point or small area electrical contacts decreased in a degraded cell compared to an unaffected cell, demonstrating the direct root cause of the Rs degradation. The degraded cell shows both a morphological and chemical difference in the screen-printed finger contact compared to the unaffected cell, which likely caused the degradation during the long-term field service. The reduction in electrical contact is likely caused by a structural change: The Ag particles in contact with the Si cell aggregate into bulk Ag, and a highly resistive ceramic oxide is formed in a "belt" shape at the Ag/Si interface. This resistive belt with a thickness of ~1 um blocks the current conduction from cell emitter to the Ag grid. Our results demonstrate an example of the multi-scale characterization approach for understanding degradation mechanisms in photovoltaics.

c-Si solar cell↗

Native Plasmid-Encoded Mercury Resistance Genes Are Functional and Demonstrate Natural Transformation in Environmental Bacterial Isolates

Plasmid-mediated horizontal gene transfer (HGT) is a major driver of genetic diversity in bacteria. We experimentally validated the function of a putative mercury resistance operon present on an abundant 8-kbp native plasmid found in groundwater samples without detectable levels of mercury. Phylogenetic analyses of the plasmid-encoded mercury reductases from the studied groundwater site show them to be distinct from those reported in proximal metal-contaminated sites. We synthesized the entire native plasmid and demonstrated that the plasmid was sufficient to confer functional mercury resistance in Escherichia coli . Given the possibility that natural transformation is a prevalent HGT mechanism in the low-cell-density environments of groundwaters, we also assayed bacterial strains from this environment for competence. We used the native plasmid-encoded metal resistance to design a screen and identified 17 strains positive for natural transformation. We selected 2 of the positive strains along with a model bacterium to fully confirm HGT via natural transformation. From an ecological perspective, the role of the native plasmid population in providing advantageous traits combined with the microbiome’s capacity to take up environmental DNA enables rapid adaptation to environmental stresses. Horizontal transfer of mobile genetic elements via natural transformation has been poorly understood in environmental microbes. Here, we confirm the functionality of a native plasmid-encoded mercury resistance operon in a model microbe and then query for the dissemination of this resistance trait via natural transformation into environmental bacterial isolates. We identified 17 strains including Gram-positive and Gram-negative bacteria to be naturally competent. These strains were able to successfully take up the plasmid DNA and obtain a clear growth advantage in the presence of mercury. Our study provides important insights into gene dissemination via natural transformation enabling rapid adaptation to dynamic stresses in groundwater environments.

59 BASIC BIOLOGICAL SCIENCES↗

Orally Bioavailable Androgen Receptor Degrader, Potential Next-Generation Therapeutic for Enzalutamide-Resistant Prostate Cancer

Androgen receptor (AR)-targeting prostate cancer drugs, which are predominantly competitive ligand-binding domain (LBD)-binding antagonists, are inactivated by common resistance mechanisms. It is important to develop next-generation mechanistically distinct drugs to treat castration- and drug-resistant prostate cancers. Second-generation AR pan antagonist UT-34 was selected from a library of compounds and tested in competitive AR binding and transactivation assays. In this study, UT-34 was tested using biophysical methods for binding to the AR activation function-1 (AF-1) domain. Western blot, gene expression, and proliferation assays were performed in various AR-positive enzalutamide-sensitive and -resistant prostate cancer cell lines. Pharmacokinetic and xenograft studies were performed in immunocompromised rats and mice. UT-34 inhibits the wild-type and LBD-mutant ARs comparably and inhibits the in vitro proliferation and in vivo growth of enzalutamide-sensitive and -resistant prostate cancer xenografts. In preclinical models, UT-34 induced the regression of enzalutamide-resistant tumors at doses when the AR is degraded; but, at lower doses, when the AR is just antagonized, it inhibits, without shrinking, the tumors. This indicates that degradation might be a prerequisite for tumor regression. Mechanistically, UT-34 promotes a conformation that is distinct from the LBD-binding competitive antagonist enzalutamide and degrades the AR through the ubiquitin proteasome mechanism. UT-34 has a broad safety margin and exhibits no cross-reactivity with G-protein–coupled receptor kinase and nuclear receptor family members. Collectively, UT-34 exhibits the properties necessary for a next-generation prostate cancer drug.

60 APPLIED LIFE SCIENCES↗