Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “process control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

The Impact of Increased Requirements for Verification Measurements of Category III and IV Receipts

As part of the regular nuclear material accounting and control process, sites that have accountable nuclear material regularly perform measurements of the material in their possession. The expectation for the type of measurements and their frequency is set out in Department of Energy (DOE) Order 474.2, and further detailed in each site’s respective material control and accountability (MC&A) plan and associated controlling documents. The measurements of interest in this report are those performed on external (between DOE sites) transfer receipts of Category III or IV accountable materials. In 2020, a revision of DOE Order 474.2 was proposed that would significantly increase the requirement that measurements be performed upon receipt of material, and further, that those measurements be quantitative verification (rather than qualitative confirmatory) measurements. A survey was performed of DOE sites to discuss the impact on their MC&A measurements program if more rigorous verification measurements requirements for Category III and IV receipts were implemented. An assessment of nondestructive assay (NDA) measurement instruments to meet those needs was also performed. Across the board, sites indicated that personnel and budget would cause the largest impact. Sites which are qualified as Category I/II indicated a reduced impact as these sites already have the measurement capabilities and some personnel but would require the acquisition of additional measurement systems. Category III/IV sites indicated a much larger impact as these sites generally have smaller MC&A programs. A few smaller sites stated a measurement program would need to be created to handle the demand. Calorimetry, quantitative gamma spectroscopy and neutron coincidence counting systems were identified as common systems that could meet the verification measurement requirements. The other, and perhaps larger issue is the need for calibration standards for the calorimetry and neutron coincidence counting systems. It is proposed that a comparative study be performed for ISOCS and ISOTOPICS, qualification of a COTS calorimetry system be performed, and development of an AWCC system that uses a neutron generator.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗

Ontology Language to Support Description of Experiment Control System Semantics, Collaborative Knowledge-Base Design and Ontology Reuse

In this paper we discuss the control domain specific ontology that is built on top of the domain-neutral Resource Definition Framework (RDF). Specifically, we will discuss the relevant set of ontology concepts along with the relationships among them in order to describe experiment control components and generic event-based state machines. Control Oriented Ontology Language (COOL) is a meta-data modeling language that provides generic means for representation of physics experiment control processes and components, and their relationships, rules and axioms. It provides a semantic reference frame that is useful for automating the communication of information for configuration, deployment and operation. COOL has been successfully used to develop a complete and dynamic knowledge-base for experiment control systems, developed using the AFECS framework.

43 PARTICLE ACCELERATORS↗

Considerations for Application of Additive Manufacturing to Nuclear Reactor Core Components

The following chapter represents the current state of literature on the selected additive manufacturing technologies and was written with an emphasis on quality control and material performance repeatability. Research and standards published by government entities such as the National Institute of Standards and Technology (NIST) and Department of Energy (DOE) have been included where applicable. It is recommended that literature be reviewed, and new knowledge integrated no less frequently than every four years due to the rapid pace of advancements in additive manufacturing and associated industries. AM presents unique challenges in certification for NPP applications such as anisotropic material properties, porosity, underdeveloped process control feedback systems, and reproducibility. This chapter begins with an overview of the selected AM technologies, followed by a systematic review of literature to detail the fabrication process and difficulties with repeatably fabricating fully dense, geometrically accurate components with known material properties.

36 MATERIALS SCIENCE↗

Unsupervised multimodal fusion of in-process sensor data for advanced manufacturing process monitoring

Effective monitoring of manufacturing processes is crucial for maintaining product quality and operational efficiency. Modern manufacturing environments often generate vast amounts of complementary multimodal data, including visual imagery from various perspectives and resolutions, hyperspectral data, and machine health monitoring information such as actuator positions, accelerometer readings, and temperature measurements. However, fusing and interpreting this complex, high-dimensional data presents significant challenges, particularly when labeled datasets are unavailable or impractical to obtain. This paper presents a novel approach to multimodal sensor data fusion in manufacturing processes, inspired by the Contrastive Language-Image Pre-training (CLIP) model. We leverage contrastive learning techniques to correlate different data modalities without the need for labeled data, overcoming limitations of traditional supervised machine learning methods in manufacturing contexts. Our proposed method demonstrates the ability to handle and learn encoders for five distinct modalities: visual imagery, audio signals, laser position (x and y coordinates), and laser power measurements. By compressing these high-dimensional datasets into low-dimensional representational spaces, our approach facilitates downstream tasks such as process control, anomaly detection, and quality assurance. The unsupervised nature of our method makes it broadly applicable across various manufacturing domains, where large volumes of unlabeled sensor data are common. We evaluate the effectiveness of our approach through a series of experiments, demonstrating its potential to enhance process monitoring capabilities in advanced manufacturing systems. This research contributes to the field of smart manufacturing by providing a flexible, scalable framework for multimodal data fusion that can adapt to diverse manufacturing environments and sensor configurations. The proposed method paves the way for more robust, data-driven decision-making in complex manufacturing processes.

Contrastive Learning↗

Diffusion-to-Imbibition Transition in Water Sorption in Nanoporous Media: Theoretical Studies

The ability to predict multiphase fluid transport in nanoporous rocks such as shales is critical for many geoscience applications, for example unconventional hydrocarbon production, geologic carbon sequestration, and nuclear waste disposal. When the pore sizes approach nanoscales, the impact of the molecular interaction forces between fluids and solids becomes increasingly important. These forces can alter macroscopic fluid phase behavior and control transport. Recent experimental studies have shown that capillary condensation and subsequent imbibition of liquid water can occur in hydrophilic nanoporous media even if the vapor phase is at a critical relative humidity (rhcrit) well below vapor saturation. This study presents a theoretical investigation of the processes controlling adsorption, capillary condensation and imbibition in nanoporous media, using the square-gradient classical density functional theory. The proposed theoretical model explicitly includes the relevant interaction forces among fluids and solids in macroscopic porous media. Application of the model to a relative-humidity-controlled water adsorption experiment is presented to demonstrate the impact of water-pore wall attractive forces on multiphase water behavior in a hydrophilic silicon nanoporous medium. Here, the model represents well the measured time-dependent evolution of the water imbibition front inside the nanoporous medium and also explains the diffusion-like water transport regimes observed at rh < rh crit and the imbibition-like flow regimes observed at rh > rh crit . The study furthermore gives an insight on hysteresis phenomenon in adsorption and desorption isotherms.

58 GEOSCIENCES↗

Neural lumped parameter differential equations with application in friction-stir processing

Lumped parameter methods aim to simplify the evolution of spatially-extended or continuous physical systems to that of a “lumped” element representative of the physical scales of the modeled system. For systems where the definition of a lumped element or its associated physics may be unknown, modeling tasks may be restricted to full-fidelity physics simulations. Here, in this work, we consider data-driven modeling tasks with limited point-wise measurements of otherwise continuous systems. We build upon the notion of the Universal Differential Equation (UDE) to construct data-driven models for reducing dynamics to that of a lumped parameter and inferring its properties. The flexibility of UDEs allow for composing various known physical priors suitable for application-specific modeling tasks, including lumped parameter methods. The motivating example for this work is the plunge and dwell stages for friction-stir welding; specifically, (i) mapping power input into the tool to a point-measurement of temperature and (ii) using this learned mapping for process control.

97 MATHEMATICS AND COMPUTING↗

A Automated Tool for Supporting FMEAs of Digital Systems

Although designs of digital systems can be very different from each other, they typically use many of the same types of generic digital components. Determining the impacts of the failure modes of these generic components on a digital system can be used to support development of a reliability model of the system. A novel approach was proposed for such a purpose by decomposing the system into a level of the generic digital components and propagating failure modes to the system level, which generally is time-consuming and difficult to implement. To overcome the associated issues of implementing the proposed FMEA approach, an automated tool for a digital feedwater control system (DFWCS) has been developed in this study. The automated FMEA tool is in nature a simulation platform developed by using or recreating the original source code of the different module software interfaced by input and output variables that represent physical signals exchanged between modules, the system, and the controlled process. For any given failure mode, its impacts on associated signals are determined first and the variables that correspond to these signals are modified accordingly by the simulation. Criteria are also developed, as part of the simulation platform, to determine whether the system has lost its automatic control function, which is defined as a system failure in this study. The conceptual development of the automated FMEA support tool can be generalized and applied to support FMEAs for reliability assessment of complex digital systems.

42 ENGINEERING↗

Distributed Wireless Antenna Sensors for Boiler Condition Monitoring

Monitoring the operational conditions of coal-fired boilers is an important task that could bring tremendous benefits, including in-situ process control, real-time health assessment of structural components, improved heat transfer efficiency, reduced downtime, etc. Moreover, in-situ distributed sensing of the boiler conditions would provide large scale in-situ measurement data that will help us gain fundamental understandings of the combustion and heat transfer processes as well as enable the developments of new simulation tools, which could eventually lead to better design and more efficient operation of the boilers. The objectives of this research were to (a) develop wireless passive antenna sensors without electronics; (b) demonstrate multi-modality sensing using a signal antenna sensor; and (c) fabricate the antenna sensor from high-temperature materials. In this project, we have demonstrated that an antenna sensor or sensor array without any electronics can be wirelessly interrogated from a distance. In addition, a low-cost compact wireless sensor interrogator was developed for dynamic interrogation of the passive antenna sensor. We validated that a dual-frequency antenna sensor is capable of simultaneous strain and temperature measurements or temperature and ash accumulation measurements; all parameters are relevant to boiler condition monitoring. By measuring the temperature and ash accumulation height simultaneously, the dielectric constant of the ash as well as its temperature dependency can also be characterized. This capability could lead to potential applications of the antenna sensor for combustion process monitoring based on the ash composition. We also investigated different techniques of fabricating the antenna sensor using high-temperature materials such as alumina substrate and platinum paste and characterized the thermal response of the antenna sensor. A linear relationship between the antenna resonant frequency and the temperature change was validated.

20 FOSSIL-FUELED POWER PLANTS↗

Processes contributing to cloud dissipation and formation events on the North Slope of Alaska

Abstract. Clear-sky periods across the high latitudes have profound impacts on the surface energy budget and lower atmospheric stratification; however an understanding of the atmospheric processes leading to low-level cloud dissipation and formation events is limited. A method to identify clear periods at Utqiaġvik (formerly Barrow), Alaska, during a 5-year period (2014–2018) is developed. A suite of remote sensing and in situ measurements from the high-latitude observatory are analyzed; we focus on comparing and contrasting atmospheric properties during low-level (below 2 km) cloud dissipation and formation events to understand the processes controlling clear-sky periods. Vertical profiles of lidar backscatter suggest that aerosol presence across the lower atmosphere is relatively invariant during the periods bookending clear conditions, which suggests that a sparsity of aerosol is not frequently a cause for cloud dissipation on the North Slope of Alaska. Further, meteorological analysis indicates two active processes ongoing that appear to support the formation of low clouds after a clear-sky period: namely, horizontal advection, which was dominant in winter and early spring, and quiescent air mass modification, which was dominant in the summer. During summer, the dominant mode of cloud formation is a low cloud or fog layer developing near the surface. This low cloud formation is driven largely by air mass modification under relatively quiescent synoptic conditions. Near-surface aerosol particles concentrations changed by a factor of 2 around summer formation events. Thermodynamic adjustment and increased aerosol presence under quiescent atmospheric conditions are hypothesized as important mechanisms for fog formation.

54 ENVIRONMENTAL SCIENCES↗

Use of Uncertainty in Modeling DFLAW Treatment at Hanford - 17115

Average or mean is understood by most; standard deviation (SD) is understood by few. Certainty is easy to model; uncertainty is not. The flowsheet simulation, described in this paper, placed uncertainties in the G2 model of the Hanford Tank Waste Treatment and Immobilization Plant's (WTP) Direct Feed Low-Activity Waste (DFLAW) process for performance and sensitivity evaluations. G2 is a dynamic material balance model that starts and proceeds with operating logic until all the feed is processed. Dynamic material balance is achieved by tracking the flows, storage, and change of all materials within the plant as time increments. Processing equipment and limitations of the flowsheet are modeled (e.g., equipment types, piping, volumes, flowrates, efficiencies, and physical and chemical environments that impact separations, phase equilibriums, and chemical reactions). Operating logic represents the rules and strategies of a running plant. The G2 model simulated both certainty and uncertainty scenarios for comparison purposes. For the uncertainty scenarios, process decisions were made using presumed values to simulate various operational measurement errors and process variabilities. Presumed means that the known G2 values are adjusted to replicate measurement errors and variabilities. These include: 1) volume measurement, 2) sample analysis, 3) melter decontamination factor (DF), 4) glass former weighing, and 5) glass former composition variations. The errors were randomly generated in accordance with SD values of measurement devices, laboratory methods, and glass former composition ranges. The G2 model runs give insight on the DFLAW process' controllability and the expected range of glass properties. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Hourly and daily rainfall intensification causes opposing effects on C and N emissions, storage, and leaching in dry and wet grasslands

Climate change is expected to alter hourly and daily rainfall regimes and, in turn, the dynamics of ecosystem processes controlling greenhouse gas emissions that affect climate. Here, we investigate the effects of expected twenty-first century changes in hourly and daily rainfall on soil carbon and nitrogen emissions, soil organic matter (SOM) stocks, and leaching using a coupled mechanistic carbon and nitrogen soil biogeochemical model (BAMS2). The model represents various abiotic and biotic processes involving 11 SOM pools. These processes include fungal depolymerization, heterotrophic bacterial mineralization, nitrification, denitrification, microbial mortality, necromass decomposition, microbial response to water stress, protection, aqueous advection and diffusion, aqueous complexation, and gaseous dissolution. Multi-decadal modeling with varying rainfall patterns was conducted on nine Australian grasslands in tropical, temperate, and semi-arid regions. Our results show that annual CO 2 emissions in the semi-arid grasslands increase by more than 20% with a 20% increase in annual rainfall (with no changes in the rainfall timing), but the tropical grasslands have opposite trends. A 20% increase in annual rainfall also increases annual N 2 O and NO emissions in the semi-arid grasslands by more than 10% but decreases emissions by at least 25% in the temperate grasslands. When subjected to low frequency and high magnitude daily rainfall events with unchanged annual totals, the semi-arid grasslands are the most sensitive, but changes in annual CO 2 emissions and SOM stocks are less than 5 %. Finally, intensification of hourly rainfall did not significantly alter CO 2 emissions and SOM stocks but changed annual NH 3 emissions in the tropical grasslands by more than 300%.

54 ENVIRONMENTAL SCIENCES↗

Multimodal characterization of solution-processed Cu3SbS4 absorbers for thin film solar cells

The most efficient inorganic thin film chalcogenide-based solar cells use CdTe or CuInGaSe2 (CIGS) as absorber layers, which rely on toxic (Cd) and/or scarce elements (In, Te). The desire for more sustainable solar cells has led to the development of Earth abundant and non-hazardous chalcogenide absorbers. Cu3SbS4 (famatinite) is a promising Earth abundant p-type semiconductor that has a low direct band gap (0.9–1.05 eV), is a superabsorber (absorption coefficient 104–105 cm1), and has potential in low-cost, thin-film solar cells. Although these properties make the Cu3SbS4 phase stand out as a promising material for photovoltaics, to date Cu3SbS4 solar cells have only achieved low efficiencies. In this study, we demonstrate a method for synthesizing Cu3SbS4 nanocrystals and formation of thin-films by coating nanocrystal precursors onto substrates. Optical, structural, and chemical state characterization were performed before and after thermal processing of the Cu3SbS4 films. A detailed experimental analysis of the bulk and surfaces of the Cu3SbS4 absorber films indicate that phase stability and preferential copper oxidation at the surface may limit device performance for Cu3SbS4 based solar cells. These findings may provide significant insight on how to improve Cu3SbS4 based solar cell performance by controlling processing conditions. This research was funded by the United States National Science Foundation – Scalable Nanomanufacturing program (Grant CBET-1449383). A portion of this research was performed at the Northwest Nanotechnology Infrastructure, a member of the National Nanotechnology Coordinated Infrastructure, which is supported by the National Science Foundation (Grant ECCS- 1542101). The acquisition of the OSU Titan TEM was supported by the National Science Foundation via the Major Research Instrumentation (MRI) program under Grant No. 1040588, the Murdock Charitable Trust, and the Oregon Nanoscience and Microtechnologies Institute (ONAMI). XANES spectra were obtained through an approved program user proposal at the Advanced Light Source, which is a DOE Office of Science User Facility under contract no. DE-AC02-05CH11231. The ALS approved program user proposal beam time was obtained through the chemical imaging initiative, an LDRD program at PNNL. We acknowledge Trey Diulus and Dr Igor Lyubinetsky for their assistance with the XPS experiments.

Albuquerque, Gustavo H.↗

Special Nuclear Material Portal Monitoring at the Nevada Test Site

In the past, acceptance and performance testing of the various Special Nuclear Material (SNM) monitoring devices at the Nevada Test Site has been performed by the Radiological Health Instrumentation Department. Calibration and performance tests on the PM-700 personnel portal monitor were performed but there was no test program for the VM-250 vehicle portal monitor because it had never been put into service. The handheld SNM monitors, the TSA model 470B, were being calibrated annually, but there was no program in place to test them quarterly. In April of 2007, the Material Control and Accountability (MC&A) Manager at the time decided that the program needed to be strengthened and MC&A took over performance testing of all SNM portal monitoring equipment. This paper will discuss the following activities associated with creating a performance testing program: changing the culture, learning the systems, writing procedures, troubleshooting/repairing, validating the process, control of equipment, acquisition of new systems, and running the program.

61 RADIATION PROTECTION AND DOSIMETRY↗

Forest Canopy Density Effects on Snowpack Across the Climate Gradients of the Western United States Mountain Ranges

Limitations inherent to field studies such as limited spatial and temporal coverage has made it very challenging, if not impossible, to explicitly disentangle the effect of canopy density from climate on snowpack dynamics. Hence, our understanding of how variations in canopy density can affect snow processes under diverse climate conditions has been limited. To address this knowledge gap, this study uses a physics-based modeling approach to represent most key processes that drive snow accumulation and melt in the open and forest with varied forest density, across the climate gradients of the Western U.S. mountain ranges, as represented by 228 Snow Telemetry (SNOTEL) locations. Simulations suggest that, under most winter climate conditions, canopy density exerts a strong influence on under-canopy snowpack dynamics and their controlling processes. Changing canopy density can shift the direction of the modeled differential peak snow accumulation and snow disappearance date (SDD) between the open and forest. For example, while simulated snowpack lasts longer in the open than the high-density forest at most wet/warm and dry/cold locations by up to 55 days, about 90% of all locations show a longer snow duration in the low-density forest by up to 27 days as compared to the open. Interannual variability in climate can also change the magnitude and direction of canopy impact on snow processes. By comparing model simulations to published field observations, and we also identify conditions that require additional field observations to improve process-scale understanding of forest-snow interaction.

54 ENVIRONMENTAL SCIENCES↗

Quantum Optimal Control of Single Harmonic Oscillator under Quadratic Controls together with Linear Dipole Polarizability: A Fluctuation Free Expectation Value Dynamical Perspective

In this study, the optimal control equations for one dimensional quantum harmonic oscillator under the quadratic control operators together with linear dipole polarizability effects are constructed in the sense of Heisenberg equation of motion. A numerical technique based on the approximation to the non-commuting quantum mechanical operators from the fluctuation free expectation value dynamics perspective in the classical limit is also proposed for the solution of optimal control equations which are ODEs with accompanying boundary conditions. The dipole interaction of the system is considered to be linear, and the observable whose expectation value will be suppressed during the control process is considered to be quadratic in terms of position operator x. The objective term operator is also assumed to be quadratic.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Elimination of carbon vacancies in 4H-SiC employing thermodynamic equilibrium conditions at moderate temperatures

The carbon vacancy (V{sub C}) is a major point defect in high-purity 4H-SiC epitaxial layers limiting the minority charge carrier lifetime. In layers grown by chemical vapor deposition techniques, the V{sub C} concentration is typically in the range of 10{sup 12 }cm{sup −3}, and after device processing at temperatures approaching 2000 °C, it can be enhanced by several orders of magnitude. In the present study, both as-grown layers and a high-temperature processed one have been annealed at 1500 °C and the V{sub C} concentration is demonstrated to be strongly reduced, exhibiting a value of only a few times 10{sup 11 }cm{sup −3} as determined by deep-level transient spectroscopy measurements. The value is reached already after annealing times on the order of 1 h and is evidenced to reflect thermodynamic equilibrium under C-rich ambient conditions. The physical processes controlling the kinetics for establishment of the V{sub C} equilibrium are estimated to have an activation energy below ∼3 eV and both in-diffusion of carbon interstitials and out-diffusion of V{sub C}'s are discussed as candidates. This concept of V{sub C} elimination is flexible and readily integrated in a materials and device processing sequence.

36 MATERIALS SCIENCE↗

Shower thoughts: why scientists should spend more time in the rain

Abstract Stormwater is a vital resource and dynamic driver of terrestrial ecosystem processes. However, processes controlling interactions during and shortly after storms are often poorly seen and poorly sensed when direct observations are substituted with technological ones. We discuss how human observations complement technological ones and the benefits of scientists spending more time in the storm. Human observation can reveal ephemeral storm-related phenomena such as biogeochemical hot moments, organismal responses, and sedimentary processes that can then be explored in greater resolution using sensors and virtual experiments. Storm-related phenomena trigger lasting, oversized impacts on hydrologic and biogeochemical processes, organismal traits or functions, and ecosystem services at all scales. We provide examples of phenomena in forests, across disciplines and scales, that have been overlooked in past research to inspire mindful, holistic observation of ecosystems during storms. We conclude that technological observations alone are insufficient to trace the process complexity and unpredictability of fleeting biogeochemical or ecological events without the shower thoughts produced by scientists’ human sensory and cognitive systems during storms.

ecosystem functioning↗