Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “prepare”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Preparation of multistage zone-refined materials for thermochemical standards

This paper describes the steps of a two-step zone purification procedure for completed minicells filled with ultrahigh-purity succinonitrile (SCN) in which the CNS is under its own vapor pressure. The solid-liquid equilibrium, as determined by melting and freezing point measurements, is therefore considered to be a realization of the triple-point. The freezing-point plateaus measured at a variety of bath temperatures demonstrated both the fundamental reproducibility of the measurement for a given sample and the lack of dependence of that measurement on the bath temperature which controls the freezing rate. The measurement reproducibility and the sample consistency indicate that the method described is indeed suitable for the preparation of pure material which can be used for the purposes of thermistor and thermometer calibration at 58.0796 + or - 0.0015 C.

Rubinstein, E.↗
NASA NTRS1988

Voyager flight engineering preparations for Neptune encounter

Voyager 2 will make the first close observations of the planet Neptune, during the period from June 1 to October 1,1989. A number of flight engineering activities are being conducted in preparation for the encounter. This paper discusses the most significant of these activities: new image motion compensation techniques, attitude control system changes, new exposure capabilities, new data handling capabilities, radiation protection measures, and new navigation methods. In addition, the process of performing late sequence updates is discussed. An overview of the Neptune mission is also presented.

Miller, L. J.↗
NASA NTRS1989

Preparation of high T(c) Tl-Ba-Ca-Cu-O thin films by pulsed laser evaporation and Tl2O3 vapor processing

Tl-Ba-Ca-Cu-O superconducting thin films with zero-resistance temperatures up to 115 K have been prepared using a Tl2O3 vapor process on Ba-Ca-Cu-O precursor thin films. The Ba-Ca-Cu-O thin films were made by laser deposition on Y-stabilized ZrO2 substrates. This technique minimizes problems caused by the toxicity of Tl2O3, and its subsequent decomposition to the volatile and toxic Tl2O upon heating. Therefore, it may have practical application in the fabrication of high T(c) Tl-Ba-Ca-Cu-O superconducting thin-film devices.

Johs, B.↗
NASA NTRS1989

Preparation of 110K (Bi, Pb)-Sr-Ca-Cu-O superconductor from glass precursor

The Bi1.5Pb0.5Sr2Ca2Cu3O(x) glass, prepared by rapid quenching of the melt, showed T(sub g) of 383 C, crystallization temperature of approx. 446 C, melting temperature of approx. 855 C, and bulk density of 5.69 g/cu. cm. in air. The as-quenched glass was oxygen deficient. On heating in O2, it showed a slow, irreversible, and continuous weight gain starting at approx. 530 C. The influence of annealing conditions on the formation of various phases was investigated by XRD and electrical resistivity measurements. The 110K-T(sub c) phase did not form below 840 C. The amount of this phase increased with the sintering time at 840 C. A sample annealed at 840 C for 243 h in air and furnace cooled showed the highest T(sub c)(R=0) of 107.2K and transition width delta T(sub c)(10 to 90 percent) of approx. 2 K.

Bansal, Narottam P.↗
NASA NTRS1990

An Auger electron spectroscopy study of surface-preparation contaminants

There are many cleaning techniques that are presently being employed for surface preparation of materials that are subsequently exposed to ultrahigh vacuum (UHV). Unfortunately, there are virtually no comparative measurements which establish the residual contaminant level of each method. In this report, eleven different cleaning methods, ranging from only detergent cleaning to electrochemical polishing, were applied to identical samples of 347 stainless steel. Two surface conditions, a standard machined surface and a mechanically polished surface, were studied. Auger electron spectroscopy (AES) within a UHV environment was then used to detect the types of contaminants and the magnitudes found on the sample surfaces. It was found that the electrochemical polishing gave the least contaminated surface of all metals studied and that mechanically polished surfaces were significantly cleaner than the as-machined surfaces for any given cleaning method. Furthermore, it was also found that the residual contaminations left by methanol, ethanol, isopropyl alcohol, acetone, and freon finishing rinses are almost the same.

Wu, D.↗
NASA NTRS1989

Method of preparing radially homogeneous mercury cadmium telluride crystals

Hg(1-x)Cd(x)Te is prepared in an improved directional solidification method in which a precast alloy sample containing predetermined amounts of Hg, Cd, and Te is disposed in a sealed ampule and a furnace providing two controlled temperature zones is translated upward past the ampule to provide melting and resolidification. The present improvement is directed to maintaining the zones at temperatures determined in accordance with a prescribed formula providing a thermal barrier between the zones with a maximum thickness and translating the furnace past the zones at a rate less the 0.31 micron/sec.

Lehoczky, Sandor L.↗
NASA NTRS1989

Transient-mode liquid phase epitaxial growth of GaAs on GaAs-coated Si substrates prepared by migration-enhanced molecular beam epitaxy

Planar oxide-maskless growth of GaAs was demonstrated by transient-mode liquid phase epitaxy (TMLPE) on GaAs-coated Si substrates that were prepared by migration-enhanced molecular beam epitaxy (MEMBE). In TMLPE, the cool substrate was brought into contact with hot melts for a short time. A GaAs layer as thick as 30 microns was grown in 10 sec. The etch pits observed in TMLPE-grown layers became longer in one direction and decreased in density with increasing the TMLPE epilayer thickness. The density of etch pits in a 20 micron-thick layer was approximately 5 x 10 the 6th/sq cm. Strong bandgap emission elliptically polarized with a major axis perpendicular to the surface was observed at about 910 nm, while deep-level emission from the TMLPE/MEMBE GaAs interface was detected at 980 nm. The photoluminescence intensity divided by the carrier concentration of the TMLPE-grown layer was about 270 times larger than that of the MEMBE-grown layer used as a substrate.

Nakamura, Shuji↗
NASA NTRS1989

Earth orbital preparation for Mars expeditions

Consideration is given to the facilities in earth orbit that would be required to prepare for a manned mission to Mars. It is suggested that the facilities required for the development of technology for a Mars mission include the Space Station, a variable gravity research station, and an assembly dock, in addition to ground facilities. The types of research that would be conducted at each of these facilities are examined.

Staehle, Robert L.↗
NASA NTRS1989

Thin-film sensors for space propulsion technology: Fabrication and preparation for testing

The goal of this work is to develop and test thin-film thermocouples for Space Shuttle Main Engine (SSME) components. Thin-film thermocouples have been developed for aircraft gas turbine engines and are in use for temperature measurement on turbine blades up to 1800 F. Established aircraft engine gas turbine technology is currently being adapted to turbine engine blade materials and the environment encountered in the SSME, especially severe thermal shock from cryogenic fuel to combustion temperatures. Initial results using coupons of MAR M-246 (+Hf) and PWA 1480 have been followed by fabrication of thin-film thermocouples on SSME turbine blades. Current efforts are focused on preparing for testing in the Turbine Blade Tester at the NASA Marshall Space Flight Center (MSFC). Future work will include testing of thin-film thermocouples on SSME blades of single crystal PWA 1480 at MSFC.

Kim, Walter S.↗
NASA NTRS1991

Ground based preparation for microgravity growth of alloy semiconductors

Ground-based research conducted in order to prepare a microgravity space flight experiment is presented. The thermophysical properties of a PbSnTe alloy used for semiconductors are investigated, and furnace calibration and fluid-flow measurements are performed. The alloy has a zero energy crossing at approximately 40 percent SnTe in its band-gap vs composition diagram, which facilitates the design of long-wavelength IR detectors and lasers. The uniformity of devices made from this material depends on the ratio of PbTe and SnTe and requires the composition of the crystal growth to be closely controlled. The main obstacle to such control is the fact that liquid of this material is always solutally or thermally unstable, and, in a high-temperature gradient, the double convective instability cannot be made stable by balancing thermal and solutal expansion. In order to extend the science of crystal growth, the limits of suppression of convection have to be tested in low earth orbit.

Fripp, Archibald L.↗
NASA NTRS1990

Preparation of 110K (Bi, Pb)-Sr-Ca-Cu-O superconductor from glass precursor

The Bi1.5Pb0.5Sr2Ca2Cu3O(x) glass, prepared by rapid quenching of the melt, showed T(sub g) of 383 C, crystallization temperature of approx. 446 C, melting temperature of approx. 855 C, and bulk density of 5.69 g/cu. cm. in air. The as-quenched glass was oxygen deficient. On heating in O2, it showed a slow, irreversible, and continuous weight gain starting at approx. 530 C. The influence of annealing conditions on the formation of various phases was investigated by XRD and electrical resistivity measurements. The 110K-T(sub c) phase did not form below 840 C. The amount of this phase increased with the sintering time at 840 C. A sample annealed at 840 C for 243 h in air and furnace cooled showed the highest T(sub c) (R=0) of 107.2 K and transition width delta T(sub c) (10 to 90 percent) of approx. 2 K.

Bansal, Narottam P.↗
NASA NTRS1990

The contribution of the preparation of the Hipparcos mission to solving the evolutionary problems of LPV's

The pulsation modes, the long-term behavior, and the evolutionary status of some long-period variable stars are discussed with reference to the results of investigations carried out as part of the preparation for the Hipparcos mission. In particular, attention is given to three different methods used to predict the brightness variations of large-amplitude (greater than 2 mag) LPVs. The discussion also covers statistical results relating to the evolutionary problems of LPVs and preliminary data on the pulsation mode.

Barthes, D.↗
NASA NTRS1991

A Process for Preparing 1,3-Diamino-5-Pentafluorosulfanylbenzene and Polymers Therefrom

Diamines have shown their utility in the formation of many polymers. Examples of these polymers include polyimides, polyamides, and epoxies. The properties of these polymers are often dependent on the diamine which is used to make the polymer. By the present invention, a process was developed to make a diamine containing pentafluorosulfanylbenzene moiety. This process involves two steps: the preparation of a dinitro precursor and the reduction of the dinitro compound to form the diamine. This diamine was then reacted with various dianhydrides, diacidchlorides, and epoxy resins to yield the corresponding polyimide, polyamide, and epoxy polymers. These polymers were then used to make films, a wire coating enamel, and a semi-permeable membrane. The novelty of this invention resides in the process to make the diamine. Traditionally, dinitro compounds are reduced with hydrazine or a catalyst such as palladium on charcoal. The catalyst which is used in this invention is platinum oxide. When this catalyst is used, it makes it possible to form a polymer-grade diamine.

St.clair, Anne K.↗
NASA NTRS1991

Preparation and characteristics of superconducting cuprate thin films: Nd(2-x)Ce(x)CuO4 and substrated Bi-system

Characteristics of the electron-doped-type Nd(sub 2-x)Ce(sub x)CuO4 system and substituted Bi-system were studied using the high quality thin film samples grown by rf magnetron sputtering and/or subsequent heat treatment. The Nd(sub 2-x)Ce(sub x)CuO4 samples with excellent superconducting properties were obtained in thin films and their optical and X-ray photoelectron spectroscopy (XPS) studies were performed with regard to the Ce content and reducing treatment. Substituted BiSr-Ln-Cu-O thin films were prepared and growth conditions for Bi-system with 2-2-1-2 and 2-2-2-2 phases were found. Moreover, a new 2-2-1-2 phase in the simple Bi-Sr-Cu-O system was fabricated by thin film processing and 80 K superconductivity was obtained.

Adachi, H.↗
NASA NTRS1991

Development, preparation, and characterization of high-performance superconducting materials for space applications

The preparation of high-temperature superconducting ceramics in bulk form is a major challenge in materials science. The current status of both partial melting and melt quenching techniques, with or without an intermediate powder processing stage, is described in detail, and the problems associated with each of the methods are discussed. Results of studies performed on melt-processed materials are reported and discussed. The discussion places emphasis on magnetization and on other physical properties associated with it, such as critical current density, levitation force, and flux creep. The nature of structural features which give rise to flux pinning, including both small and large defects, is discussed with reference to theoretical considerations. The rates of flux creep and the factors involved in attempting to retard the decay of the magnetization are surveyed.

Thorpe, Arthur N.↗
NASA NTRS1992

Glass sample preparation and performance investigations

This final report details the work performed under this delivery order from April 1991 through April 1992. The currently available capabilities for integrated optical performance modeling at MSFC for large and complex systems such as AXAF were investigated. The Integrated Structural Modeling (ISM) program developed by Boeing for the U.S. Air Force was obtained and installed on two DECstations 5000 at MSFC. The structural, thermal and optical analysis programs available in ISM were evaluated. As part of the optomechanical engineering activities, technical support was provided in the design of support structure, mirror assembly, filter wheel assembly and material selection for the Solar X-ray Imager (SXI) program. As part of the fabrication activities, a large number of zerodur glass samples were prepared in different sizes and shapes for acid etching, coating and polishing experiments to characterize the subsurface damage and stresses produced by the grinding and polishing operations. Various optical components for AXAF video microscope and the x-ray test facility were also fabricated. A number of glass fabrication and test instruments such as a scatter plate interferometer, a gravity feed saw and some phenolic cutting blades were fabricated, integrated and tested.

Johnson, R. Barry↗
NASA NTRS1990

The NASA Space Life Sciences Training Program - Preparing the way

Attention is given to the goals and methods adopted in the NASA Space Life Sciences Training Program (SLSTP) for preparing scientists and engineers for space-related life-sciences research and operations. The SLSTP is based on six weeks of projects and lectures which give an overview of payload processing and experiment flow in the space environment. The topics addressed in the course of the program include descriptions of space vehicles, support hardware, equipment, and research directions. Specific lecture topics include the gravity responses of plants, mission integration of a flight experiment, and the cardiovascular deconditioning. The SLSTP is shown to be an important part of the process of recruiting and training qualified scientists and engineers to support space activities.

Biro, Ronald↗