SEARCH · Engineering Papers

Results for “prediction methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

All sources NASA NTRS DOE OSTI

NASA NTRS1975

Diagnostic calculations of airframe-radiated noise

Methods of calculating airframe noise due to the following components are presented: wings and stabilizers, flaps, landing gear 'self-noise', landing gear bay (wheel well) oscillations, separated flow interaction with edges of cavities, and doors associated with gear deployment. The predominant source mechanisms were dipole-like in nature, being related to the local fluctuating aerodynamic forces on struts, airfoil edges, cavity edges, etc. Available data are converted into semiempirical prediction methods to enable a tentative rank ordering of noise sources. A sample application of these prediction procedures is carried out for a typical CTOL passenger jet using actual aircraft parameters, where available.

Hayden, R. E.↗

NASA NTRS1976

Prediction of light aircraft interior noise

A computerized interior noise prediction method for light aircraft is described. An existing analytical program, development for commercial jets, forms the basis of some modal analysis work which is described. The accuracy of this modal analysis technique for predicting low-frequency coupled acoustic-structural natural frequencies is discussed along with trends indicating the effects of varying parameters such as fuselage length and diameter, structural stiffness, and interior acoustic absorption.

Howlett, J. T.↗

NASA NTRS1996

Simulation of Three-Dimensional Symmetric and Asymmetric Instabilities in Attachment-Line Boundary Layers

On a swept wing, contamination along the leading edge, Tollmien-Schlichting waves, stationary or traveling crossflow vortices, and/or Taylor-Gortler vortices can cause the catastrophic breakdown of laminar to turbulent flow, which leads to increased skin-friction drag for the aircraft. The discussion in this Note will be limited to disturbances which evolve along the attachment line (leading edge of swept wing). If the Reynolds number of the attachment-line boundary layer is greater than some critical value, then the complete wing is inevitably engulfed in turbulent flow. Essentially, there are two critical Reynolds number points that must be considered. The first is for small-amplitude disturbances, and the second is for bypass transition. The present study will use direct numerical simulations to validate a linear 2D-eigenvalue prediction method based on parabolized stability equations by Lin and Malik. This method is considered because it suggests that a number of symmetric and asymmetric modes exist and are stable or unstable on the attachment line depending on the Reynolds number. If validated, the approach would predict a number of modes which are linearly damped in the Reynolds number regime 100 to 245; however, these modes may grow nonlinearly and provide an explanation to this region.

Joslin, Ronald D.↗

NASA NTRS1976

Measurement, analysis, and prediction of aircraft interior noise

Considerations of comfort of passengers and crew in light aircraft and helicopters indicate substantial benefits may be obtained by the reduction of interior noise levels. This paper discusses an ongoing research effort to reduce interior noise in such vehicles. Data from both field and laboratory studies for a light aircraft are presented. The laboratory data indicate that structural vibration is an efficient source of interior noise and should be considered in the reduction of interior noise. Flight data taken on a helicopter before and after installation of acoustic treatment demonstrate that over 30 dB of noise reduction can be obtained in certain portions of the spectra. However, subjective evaluations of the treated vehicle indicate that further reductions in interior noise are desirable. An existing interior noise prediction method which was developed for large jet transports was applied to study low-frequency noise in a light aircraft fuselage. The results indicate that improvements in the analytical model may be necessary for the prediction of interior noise of light aircraft.

Howlett, J. T.↗

NASA NTRS1986

Turbine Engine Hot Section Technology 1986

On October 21 and 22, 1986, the Turbine Engine Hot Section Technology (HOST) Project of the NASA Lewis Research Center sponsored a workshop to discuss current research pertinent to turbine engine durability problems. Presentations were made concerning the hot-section environment and the behavior of combustion liners, turbine blades, and turbine vanes. The presentations were divided Into six sessions: Instrumentation, Combustion, Turbine Heat Transfer, Structural Analysis, Fatigue and Fracture, and Surface Protection. The principal objective of each session was to disseminate research results to date. Topics discussed included modeling of thermal and fluid-flow phenomena, structural analysis, fatigue and fracture, surface protective coatings, constitutive behavior of materials, stress-strain response, and life-prediction methods. Researchers from industry, academia, and government presented results of their work sponsored by the HOST Project. This publication contains extended abstracts and visual material presented during the workshop.

Turbine Engine Hot Section Technology (HOST)↗

NASA NTRS1987

Cruise noise of the 2/9th scale model of the Large-scale Advanced Propfan (LAP) propeller, SR-7A

Noise data on the Large-scale Advanced Propfan (LAP) propeller model SR-7A were taken in the NASA Lewis Research Center 8 x 6 foot Wind Tunnel. The maximum blade passing tone noise first rises with increasing helical tip Mach number to a peak level, then remains the same or decreases from its peak level when going to higher helical tip Mach numbers. This trend was observed for operation at both constant advance ratio and approximately equal thrust. This noise reduction or, leveling out at high helical tip Mach numbers, points to the use of higher propeller tip speeds as a possible method to limit airplane cabin noise while maintaining high flight speed and efficiency. Projections of the tunnel model data are made to the full scale LAP propeller mounted on the test bed aircraft and compared with predictions. The prediction method is found to be somewhat conservative in that it slightly overpredicts the projected model data at the peak.

Dittmar, James H.↗

NASA NTRS1987

Predictions of F-111 TACT aircraft buffet response and correlations of fluctuating pressures measured on aluminum and steel models and the aircraft

Results of buffet research that was conducted as part of the joint USAF/NASA F-111 TACT Research Program are presented. The correlation of wind tunnel and flight measurements of buffet excitation showed that there generally was good agreement between measurements of pressure fluctuations on the models and aircraft in regions of separated flow. At shock-wave boundaries of the separated flow, correlations of pressure fluctuations were not so good, due to Reynolds number and static elastic effects. The buffet prediction method, which applies a forcing function that is obtained by real-time integration of pressure time histories with the natural modes, is described. The generalized forces, including the effects of wing and tail, correlations of predicted and measured damping, and correlations of predicted and measured buffet response are presented. All presented data are for a Mach number of 0.8 with wing-sweep angles of 26 and 35 deg for a range of angles-of-attack that include buffet onset to high intensity buffeting. Generally, the buffet predictions were considered to be quite good particularly in light of past buffet-prediction experience.

Coe, Charles F.↗

NASA NTRS1987

Cruise noise of the 2/9 scale model of the Large-scale Advanced Propfan (LAP) propeller, SR-7A

Dittmar, James H.↗

NASA NTRS1976

Prediction of light aircraft interior noise

At the present time, predictions of aircraft interior noise depend heavily on empirical correction factors derived from previous flight measurements. However, to design for acceptable interior noise levels and to optimize acoustic treatments, analytical techniques which do not depend on empirical data are needed. This paper describes a computerized interior noise prediction method for light aircraft. An existing analytical program (developed for commercial jets by Cockburn and Jolly in 1968) forms the basis of some modal analysis work which is described. The accuracy of this modal analysis technique for predicting low-frequency coupled acoustic-structural natural frequencies is discussed along with trends indicating the effects of varying parameters such as fuselage length and diameter, structural stiffness, and interior acoustic absorption.

Howlett, J. T.↗

NASA NTRS2000

Material Characterization for Ductile Fracture Prediction

The research summarized in this document provides valuable information for structural health evaluation of NASA infrastructure. Specifically, material properties are reported which will enable calibration of ductile fracture prediction methods for three high-toughness metallic materials and one aluminum alloy which can be found in various NASA facilities. The task of investigating these materials has also served to validate an overall methodology for ductile fracture prediction is currently being employed at NASA. In facilitating the ability to incorporate various materials into the prediction scheme, we have provided data to enable demonstration of the overall generality of the approach.

Hill, Michael R.↗

NASA NTRS1994

Large-eddy simulation of a boundary layer with concave streamwise curvature

Turbulence modeling continues to be one of the most difficult problems in fluid mechanics. Existing prediction methods are well developed for certain classes of simple equilibrium flows, but are still not entirely satisfactory for a large category of complex non-equilibrium flows found in engineering practice. Direct and large-eddy simulation (LES) approaches have long been believed to have great potential for the accurate prediction of difficult turbulent flows, but the associated computational cost has been prohibitive for practical problems. This remains true for direct simulation but is no longer clear for large-eddy simulation. Advances in computer hardware, numerical methods, and subgrid-scale modeling have made it possible to conduct LES for flows or practical interest at Reynolds numbers in the range of laboratory experiments. The objective of this work is to apply ES and the dynamic subgrid-scale model to the flow of a boundary layer over a concave surface.

Lund, Thomas S.↗

NASA NTRS1986

Shaping of airplane fuselages for minimum drag

The VSAERO surface panel method is employed to investigate fuselage shapes which can enhance the natural laminar flow (NLF) characteristics. The study is performed at cruise Re which are relevant to commuter, transport, and business aircraft. The technique is based on piecewise constant doublet and source singularities and takes into account the effects of compressibility. Inviscid pressure distributions were generated for five configurations to aid in the search for an optimized NLF body shape as a function of the transition locations and the drag coefficients. Granville's transition criteria are incorporated into the calculations to yield shapes with longer runs of laminar flow and reduced drag. In comparison with other transition prediction methods, the method described is shown to have significantly higher valicity for making three-dimensional transition predictions.

Dodbele, S. S.↗

NASA NTRS1993

Application of an engineering inviscid-boundary layer method to slender three-dimensional vehicle forebodies

An engineering inviscid-boundary layer method has been modified for application to slender three-dimensional (3-D) forebodies which are characteristic of transatmospheric vehicles. An improved shock description in the nose region has been added to the inviscid technique which allows the calculation of a wider range of body geometries. The modified engineering method is applied to the perfect gas solution over a slender 3-D configuration at angle of attack. The method predicts surface pressures and laminar heating rates on the windward side of the vehicle that compare favorably with numerical solutions of the thin-layer Navier-Stokes equations. These improvements extend the 3-D capabilities of the engineering method and significantly increase its design applications.

Riley, Christopher J.↗

NASA NTRS1993

Application of an Engineering Inviscid-Boundary Layer Method to Slender Three-Dimensional Vehicle Forebodies

Riley, Christopher J.↗

NASA NTRS1991

Generic hypersonic inlet module analysis

A computational study associated with an internal inlet drag analysis was performed for a generic hypersonic inlet module. The purpose of this study was to determine the feasibility of computing the internal drag force for a generic scramjet engine module using computational methods. The computational study consisted of obtaining two-dimensional (2D) and three-dimensional (3D) computational fluid dynamics (CFD) solutions using the Euler and parabolized Navier-Stokes (PNS) equations. The solution accuracy was assessed by comparisons with experimenal pitot pressure data. The CFD analysis indicates that the 3D PNS solutions show the best agreement with experimental pitot pressure data. The internal inlet drag analysis consisted of obtaining drag force predictions based on experimental data and 3D CFD solutions. A comparative assessment of each of the drag prediction methods is made and the sensitivity of CFD drag values to computational procedures is documented. The analysis indicates that the CFD drag predictions are highly sensitive to the computational procedure used.

Cockrell, Charles E., Jr.↗

NASA NTRS2004

Generic Hypersonic Inlet Module Analysis

A computational study associated with an internal inlet drag analysis was performed for a generic hypersonic inlet module. The purpose of this study was to determine the feasibility of computing the internal drag force for a generic scramjet engine module using computational methods. The computational study consisted of obtaining two-dimensional (2D) and three-dimensional (3D) computational fluid dynamics (CFD) solutions using the Euler and parabolized Navier-Stokes (PNS) equations. The solution accuracy was assessed by comparisons with experimental pitot pressure data. The CFD analysis indicates that the 3D PNS solutions show the best agreement with experimental pitot pressure data. The internal inlet drag analysis consisted of obtaining drag force predictions based on experimental data and 3D CFD solutions. A comparative assessment of each of the drag prediction methods is made and the sensitivity of CFD drag values to computational procedures is documented. The analysis indicates that the CFD drag predictions are highly sensitive to the computational procedure used.

Cockrell, Chares E., Jr.↗

NASA NTRS1972

Analytic prediction of dynamic stall characteristics.

A new approach is presented for solving the problem of predicting dynamic stall characteristics. In this approach, the unsteady aerodynamic characteristics are related theoretically to static aerodynamic characteristics which are readily available for a great number of airfoil shapes. Using these static experimental data as an input, the developed analytical method predicts dynamic stall characteristics that are in good agreement with available experimental data. The analysis is also extended to include frequency and amplitude modulation effects.

Ericsson, L. E.↗

NASA NTRS1974

The numerical calculation of inviscid plume flow fields

A numerical method is presented for the computation of inviscid, axisymmetric, underexpanded plumes. The numerical techniques developed by Moretti (1969, 1971, 1972) are used in conjunction with Abbett's (1970) theory for locating the Mach disk. Abbett's theory and three other prediction methods are compared to experimental results. Results are presented for jets exhausting into static ambients and supersonic free stream. Detailed results from a flow field with multiple Mach disks are also presented. Finally, some problems associated with the computation of very small Mach disks are discussed.

Salas, M. D.↗