Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “performance degradation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Radiation-hard miniature optical engine with high bandwidth

Future silicon trackers will be operated in an intense radiation environment and require large volumes of data to be transmitted off detector. In addition, the optical modules must be of low mass in order to limit multiple scattering and nuclear interactions that would degrade the overall performance of the detector. Here, we present a miniature optical engine that satisfies these constraints. The optical engine consists of an ASIC driving a VCSEL (Vertical Cavity Surface Emitting Laser) array in an optical package. Two ASICs are designed to operate a 12-channel VCSEL array at 1.28 or 5.12 Gb/s per channel, which yields a total data rate of up to 60 Gb/s. The core transistors are fabricated in a 65 nm CMOS process which enhance the radiation-hardness. Each channel contains equalizer (CTLE) and clock-data recovery circuits (CDR) so that the ASIC can restore the highly distorted electrical signal after propagating through several meters of cables of small diameter. The equalizer, CDR, and VCSEL driver are configured via a digital I 2 C chip interface with triple redundant memory to mitigate single event upset (SEU) effects. The bias and modulation currents are controlled by a digital-to-analog converter (DAC). We present the design of the circuit together with the results of the simulations and preliminary measurements.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Thermal stability of dopants in boron carbide

Undoped (B 4 C), B rich (B 5.5 C), and B/Si co-doped (Si-B 6.5 C) boron carbides were annealed at 500 °C for up to 21 days to investigate the thermal stability of primary dopants, B and Si. Structural changes associated with dedoping were investigated by X-ray diffraction (XRD) and Raman spectroscopy. The stable phase B 4 C showed no microstructural or lattice parameter changes. Similarly, lattice parameters of B 5.5 C remained constant, suggesting that B dopant is stable at the given conditions. However, the shortened lattice parameters and reduced Si content of Si-B 6.5 C over the annealing time indicated that Si dopant was in a metastable state at the annealing temperature. Consequently, Si dedoping led to an increase in amorphization (a loss of local crystalline order) which degrades the ballistic performance of boron carbide. The insight highlights the importance of Si dopant in boron carbide and suggests that rapid processing may be necessary to retain more silicon for better performance.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Copper-Doped Tin Oxides Supported on Mesoporous Carbon Xerogel for Boosting the Electrochemical Reduction of CO 2 to Formate in Bicarbonate Solution Coupled with CO 2

The electrochemical reduction of CO 2 into valuable products at mild reaction conditions and using cheap renewable electrical energy are goals to sustain a low-carbon economy. Among the various CO 2 reduction reaction products, formic acid (FA) has received significant attention because of its low Gibbs free energy input requirement and the simple reduction reaction involving the transfer of 2 electrons and 2 protons. In this work, a copper-doped tin oxide catalyst supported on a mesoporous carbon xerogel was shown to enhance the electrochemical reduction of CO 2 to formate in a bicarbonate solution coupled with CO 2 . We observed that the synergistic SnCu oxides enhance the selectivity toward formate from 58.6% for Sn oxide and 28.7% for Cu oxide to over 71.2% for the SnCu oxides. The observed rate of formate production with SnCu oxide was 2.8 times higher compared to the rate of Cu oxide and about 1.5 times higher than with the Sn oxide catalyst. Our results reveal that selectivity for formate comes partly from the electrolysis of the bicarbonate solution and partly from continuous CO 2 gas purged into the solution. The contribution from the electrolysis of bicarbonate solution ranges from 15% to 40% when the concentration of bicarbonate solution ranges from 100 mM to 1 M. Chronoamperometric measurements for stability revealed that Cu oxide and Sn oxide showed stable current density for less than 30 h while under the same conditions, the stable current density was observed for more than 50 h with SnCu oxide catalyst. Additionally, the selectivity toward formate increased by 6% when the reactor pressure was increased from near ambient pressure to 4 psig. Our lab-scale electrochemical cell with SnCu oxide supported on the mesoporous carbon xerogel enhances the CO 2 solubility, minimizes the precipitation of salts that can degrade the catalytic performance, and suppresses the competitive hydrogen evolution reaction, demonstrating the feasibility of using our catalyst and system for the electrochemical conversion of CO 2 into formate with high selectivity, productivity, and stability. Furthermore, this could have significant implications for the mitigation of CO 2 emissions and the development of a sustainable chemical industry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Band-edge Engineering to Eliminate Radiation-Induced Defect States in Perovskite Scintillators

Under radiative environments such as extended hard X- or γ-rays, degradation of scintillation performance is often due to irradiation-induced defects. To overcome the effect of deleterious defects, novel design mitigation strategies are needed to identify and design more resilient materials. The potential for band-edge engineering to eliminate the effect of radiation-induced defect states in rare-earth-doped perovskite scintillators is explored, taking Ce 3+ -doped LuAlO 3 as a model material system, using density functional theory (DFT)-based DFT + U and hybrid Heyd–Scuseria–Ernzerhof (HSE) calculations. Furthermore, from spin-polarized hybrid HSE calculations, the Ce 3+ activator ground-state 4f position is determined to be 2.81 eV above the valence band maximum in LuAlO 3 . Except for the oxygen vacancies which have a deep level inside the band gap, all other radiation-induced defects in LuAlO 3 have shallow defect states or are outside the band gap, that is, relatively far away from either the 5d 1 or the 4f Ce 3+ levels. Finally, we examine the role of Ga doping at the Al site and found that LuGaO 3 has a band gap that is more than 2 eV smaller than that of LuAlO 3 . Specifically, the lowered conduction band edge envelopes the defect gap states, eliminating their potential impact on scintillation performance and providing direct theoretical evidence for how band-edge engineering could be applied to rare-earth-doped perovskite scintillators.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Comparative Study of Vinylene Carbonate and Lithium Difluoro(oxalate)borate Additives in a SiO x /Graphite Anode Lithium-Ion Battery in the Presence of Fluoroethylene Carbonate

The SiO x /graphite composite is recognized as a promising anode material for lithium-ion batteries (LIBs), owing to the high theoretical capacity of SiO x combined with the excellent stability of graphite. However, the inherent disadvantage of volume expansion in silicon-based anodes places significant challenges on the solid electrolyte interphase (SEI) and severely degrades the electrochemical performance. Rational formulation of electrolyte, including its additives, is crucial in accommodating and optimizing the composition of the SEI and enhancing the cell performance. In this work, we present a comparative study of vinylene carbonate (VC) and lithium difluoro(oxalate)borate (LiDFOB) additives combined with fluoroethylene carbonate (FEC) in the electrolyte for SiO x /graphite∥LiNi 1–x–y–z Co x Mn y Al z O 2 full cells. VC outperformed LiDFOB as an additive, delivering higher capacity cycling, higher Coulombic efficiency, and better cycle stability up to 400 cycles. XPS and impedance analyses reveal that LiDFOB contributed to SEI/CEI with both a lower proportion of LiF and a higher proportion of poly(VC), which tended to produce higher cell impedance. XRD and XANES further indicated that using the LiDFOB additive, the NCMA cycled to a shallower degree than that of the VC additive. Although the VC additive maintained a higher capacity up to 400 cycles, microstrain and SEM analyses show a higher strained NCMA along with clear evidence of cracking over the surface of the NCMA particle in VC-based electrolyte but not in LiDFOB. In conclusion, this suggests that the negative influence of LiDFOB at the anode (inferior SEI) supersedes the negative impact of both a cracked NCMA and a deeper cycled NCMA and SiO x -based anode.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Self-Heating Conductive Ceramic Composites for High Temperature Thermal Energy Storage

The absence of affordable and deployable large-scale energy storage poses a major barrier to providing zero-emission energy on demand for societal decarbonization. High temperature thermal energy storage is one promising option with low cost and high scalability, but it is hindered by the inherent complexity of simultaneously satisfying all of the material requirements. Here we design a class of ceramic–carbon composites based on co-optimizing mechanical, electrical, and thermal properties. Further, these composites demonstrate stability in soak-and-hold tests and direct self-heating up to 1,936 °C and 750 thermal cycles from 500 to 1,630 °C without degradation. This thermal performance derives from their composition and microstructural design as verified by in situ high-temperature transmission electron microscopy and X-ray diffraction. They offer both higher energy density and lower cost than conventional storage technologies with a projected system Levelized Cost of Storage below the U.S. Department of Energy’s 2030 target 5 ¢/kWh (electric).

25 ENERGY STORAGE↗
DOE OSTI2021

In Situ Visualization of Li-Whisker with Grating-Interferometry-Based Tricontrast X-ray Microtomography

The lithium-ion battery has demonstrated tremendous economic and social impacts. Upon battery operation under different conditions, lithium changes its chemical state and physical formation, leading to undesired side reactions, e.g., lithium dendrite growth that degrades the cell performance and causes safety concerns. In situ detection and visualization of lithium metal in functional batteries could offer insights with both scientific and industrial significance but remain a frontier challenge. In this work, we demonstrate in situ three-dimensional imaging of lithium whisker using a grating-interferometry-based tricontrast X-ray microtomography method. Our approach explicitly reveals the micromorphology of the electrochemically developed porous lithium whisker with micrometer-level spatial resolution while offering sensitivity to the nanoporosity that is smaller than the nominal resolution limit. Our result reveals valuable structural information on the lithium whisker that is otherwise inaccessible. This method is also readily applicable to a broad range of battery research, including all-solid-state batteries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Combining Remotely Sensed Evapotranspiration and an Agroecosystem Model to Estimate Center‐Pivot Irrigation Water Use at High Spatio‐Temporal Resolution

Abstract Estimating irrigation water use accurately is critical for sustainable irrigation and studying terrestrial water cycle in irrigated croplands. However, irrigation is not monitored in most places, and current estimations of irrigation water use has coarse spatial and/or temporal resolutions. This study aims to estimate irrigation water use at the daily and field scale through the proposed model‐data fusion framework, which is achieved by particle filtering with two configurations (concurrent, CON, and sequential, SEQ) by assimilating satellite‐based evapotranspiration (ET) observations into an advanced agroecosystem model, ecosys . Two types of experiments using synthetic and real ET observations were conducted to study the efficacy of the proposed framework for estimating irrigation water use at the irrigated fields in eastern and western Nebraska, United States. The experiments using synthetic ET observations indicated that, for two major sources of uncertainties of ET difference between observations and model simulations, which are bias and noise, noise had larger impacts on degrading the estimation performance of irrigation water use than bias. For the experiments using real ET observations, monthly and annual estimations of irrigation water use matched well with farmer irrigation records, with Pearson correlation coefficient ( r ) around 0.80 and 0.50, respectively. Although detecting daily irrigation records was very challenging, our method still gave a good performance with RMSE, BIAS, and r around 2.90, 0.03, and 0.4 mm/d, respectively. Our proposed model‐data fusion framework for estimating irrigation water use at high spatio‐temporal resolution could contribute to regional water management, sustainable irrigation, and better tracking terrestrial water cycle.

Environmental Sciences & Ecology↗
DOE OSTI2024

An Evaluation of Dynamical Downscaling Methods Used to Project Regional Climate Change

In the past decade, dynamical downscaling using “pseudo-global-warming” (PGW) techniques has been applied frequently to project regional climate change. Such techniques generate signals by adding mean global climate model (GCM)-simulated climate change signals in temperature, moisture, and circulation to lateral and surface boundary conditions derived from reanalysis. An alternative to PGW is to downscale GCM data directly. This technique should be advantageous, especially for simulation of extremes, since it incorporates the GCM's full spectrum of changing synoptic-scale dynamics in the regional solution. Here, we test this assumption, by comparing simulations in Europe and Western North America. We find that for warming and changes in temperature extremes, PGW often produces similar results to direct downscaling in both regions. For mean and extreme precipitation changes, PGW generally also performs surprisingly well in many cases. Moisture budget analysis in the Western North America domain reveals why. Large fractions of the downscaled hydroclimate changes arise from mean changes in large-scale thermodynamics and circulation, that is, increases in temperature, moisture, and winds, included in PGW by design. The one component PGW may have difficulty with is the contribution from changes in synoptic-scale variability. When this component is large, PGW performance could be degraded. Global analysis of GCM data shows there are regions where it is large or dominant. Hence, our results provide a road map to identify, through GCM analyses, the circumstances when PGW would not be expected to accurately regionalize GCM climate signals.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Evaluation of a Stochastic Mixing Scheme in the Deep Convective Gray Zone Using a Tropical Oceanic Deep Convection Case Study

Abstract A stochastic horizontal subgrid‐scale mixing scheme is evaluated in ensemble simulations of a tropical oceanic deep convection case using a horizontal grid spacing (Δ h ) of 3 km. The stochastic scheme, which perturbs the horizontal mixing coefficient according to a prescribed spatiotemporal autocorrelation scale, is found to generally increase mesoscale organization and convective intensity relative to a non‐stochastic control simulation. Perturbations applied at relatively short autocorrelation scales induce differences relative to the control that are more systematic than those from perturbations applied at relatively long scales that yield more variable outcomes. A simulation with mixing enhanced by a constant factor of 4 significantly increases mesoscale organization and convective intensity, while turning off horizontal subgrid‐scale mixing decreases both. Total rainfall is modulated by a combination of mesoscale organization, areal coverage of convection, and convective intensity. The stochastic simulations tend to behave more similarly to the constant enhanced mixing simulation owing to greater impacts from enhanced mixing as compared to reduced mixing. The impacts of stochastic mixing are robust, ascertained by comparing the stochastic mixing ensembles with a non‐stochastic mixing ensemble that has grid‐scale noise added to the initial thermodynamic field. Compared to radar observations and a higher resolution Δ h = 1 km simulation, stochastic mixing seemingly degrades the simulation performance. These results imply that stochastic mixing produces non‐negligible impacts on convective system properties and evolution but does not lead to an improved representation of convective cloud characteristics in the case studied here.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Wavelength conversion through plasmon-coupled surface states

Surface states generally degrade semiconductor device performance by raising the charge injection barrier height, introducing localized trap states, inducing surface leakage current, and altering the electric potential. We show that the giant built-in electric field created by the surface states can be harnessed to enable passive wavelength conversion without utilizing any nonlinear optical phenomena. Photo-excited surface plasmons are coupled to the surface states to generate an electron gas, which is routed to a nanoantenna array through the giant electric field created by the surface states. The induced current on the nanoantennas, which contains mixing product of different optical frequency components, generates radiation at the beat frequencies of the incident photons. We utilize the functionalities of plasmon-coupled surface states to demonstrate passive wavelength conversion of nanojoule optical pulses at a 1550 nm center wavelength to terahertz regime with efficiencies that exceed nonlinear optical methods by 4-orders of magnitude.

42 ENGINEERING↗
DOE OSTI2020

Graphene-assisted spontaneous relaxation towards dislocation-free heteroepitaxy

While conventional homoepitaxy forms high-quality epitaxial layers, the limited set of material systems for commercially available wafers restricts the range of materials that can be grown homoepitaxially. At the same time, conventional heteroepitaxy of lattice-mismatched systems produces dislocations above a critical strain energy to release the accumulated strain energy as the film thickness increases. The formation of dislocations, which severely degrade electronic/photonic device performances, is fundamentally unavoidable in highly lattice-mismatched epitaxy. Herein, we introduce a unique mechanism of relaxing misfit strain in heteroepitaxial films that can enable effective lattice engineering. We have observed that heteroepitaxy on graphene-coated substrates allows for spontaneous relaxation of misfit strain owing to the slippery graphene surface while achieving single-crystalline films by reading the atomic potential from the substrate. This spontaneous relaxation technique could transform the monolithic integration of largely lattice-mismatched systems by covering a wide range of the misfit spectrum to enhance and broaden the functionality of semiconductor devices for advanced electronics and photonics.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2020

Understanding the thermally activated charge transport in NaPb m SbQ m+2 (Q = S, Se, Te) thermoelectrics: weak dielectric screening leads to grain boundary dominated charge carrier scattering

Many thermoelectric materials feature irregular electrical conductivity with thermally activated transport below ~600 K and metallic behavior at high temperatures, despite possessing degenerate carrier concentrations. The suppression of the electrical conductivity ultimately degrades the thermoelectric performance on the cold side and limits the device energy conversion efficiency. As such, establishing the origin of the low temperature scattering and developing strategies to mitigate its effect are paramount issues. To date, the correct microscopic description of the low temperature carrier scattering remains an open issue, and there is little work addressing why some thermoelectric materials are more susceptible to the deleterious behavior. Here, we use the promising thermoelectric alloys of PbQ and NaSbQ 2 (Q = S, Se, Te) as model systems to address these concerns. We directly show the thermally activated transport stems from the scattering of charge carriers by the grain boundaries (GBs), and that the expected metallic electrical conductivity is recovered by preparing large grained samples with reduced densities of GBs. We furthermore study the electrical properties NaPb m SbSe m+2 as a function of NaSbSe 2 fraction, as well as those of the chalcogenide analogues, PbTe–NaSbTe 2 and PbS–NaSbS 2 , and demonstrate that the strength of GB scattering can be understood by utilizing simple chemical principles. By considering the polarizability of the host atoms, we directly relate the magnitude of GB scattering to the relative degree of charge carrier screening in each material, and demonstrate that GB scattering is strongest in the ionic NaSbQ 2 -rich compounds and weakest in more polarizable PbQ-rich phases. We finally show how these chemical arguments elegantly explain the strong GB scattering in numerous other thermoelectric materials. By uniting the deleterious charge transport properties exhibited by many different compounds into a common picture, we discuss how our work gives design principles for proper microstructure engineering in emerging thermoelectric materials.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Mechanisms of shape transfer and preheating in indirect-drive double shell collisions

Implosions of Hohlraum-driven double shell targets as an alternative inertial confinement fusion concept are underway at the National Ignition Facility. The double shell system relies on a series of energy transfer processes starting from thermal x-ray absorption by the outer shell, followed by collisional transfer of kinetic energy to a heavy metal inner shell, and finally, conversion to the internal energy of the deuterium-tritium fuel. During each of these energy transfer stages, low-mode asymmetries can act to reduce the ideal transfer efficiency degrading double shell performance. Mechanisms, such as hard x-ray preheat from the Hohlraum, not only decrease the efficiency of kinetic energy transfer but may also be a source of low-mode asymmetry. In this article, we evaluate the shape transfer processes through the time of shell collision using two-dimensional integrated Hohlraum and capsule computations. We find that the dominant mode of the shape transfer is well described using a “radial impulse” model from the shape of the foam pressure reservoir. To evaluate the importance of preheat on inner shell shape, we also report on first measurements of Au L-shell preheat asymmetry in a double shell with a tungsten pusher. These measurements showed a 65% higher preheat velocity at the pole of the capsule relative to the equator. We also found that the experiments provided rigorous constraints by which to test the Hohlraum model settings that impact the amount and symmetry of Au L-shell preheat via the plasma conditions inside the outer cone Au bubble.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

A future of inertial confinement fusion without laser-plasma instabilities

From the beginning of inertial confinement fusion (ICF) research, laser-plasma instabilities excited by narrowband lasers have limited the hydrodynamic design space of all laser-based approaches to inertial fusion energy (IFE). With advances in broadband laser technologies, the next generation of ICF drivers will likely have large bandwidth that is engineered to mitigate laser-plasma instabilities, thereby expanding the hydrodynamic design space to include both robust high yields (>200−MJ) with large-energy laser systems (>4 MJ) and high gains (>10) with moderate-energy laser facilities (<2 MJ). State-of-the-art simulations indicate that laser bandwidths of a few percent are required to mitigate instabilities for IFE-relevant conditions. To test these models and demonstrate that high-bandwidth lasers mitigate laser-plasma instabilities, the Fourth-generation Laser for Ultrabroadband eXperiments will be used with the OMEGA Laser System. The goal is to provide the community with the confidence to invest in a multiple-beam high-bandwidth laser facility that will demonstrate the necessary ablation pressures for robust direct-drive ignition without detrimental levels of hot electrons that degrade the implosion performance. It is important to recognize that the highest performing ICF implosions will likely never be completely LPI free because of the significant advantages to maximizing the laser intensity.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Fiber-optic bolometers with high-temperature tolerance and reduced time constants for fusion plasma diagnostics

Fiber-optic bolometers (FOBs) designed for plasma radiation measurement in magnetically confined fusion environments have been previously developed and tested at the DIII-D tokamak. These FOBs utilize a silicon Fabry–Perot interferometer at the fiber tip for temperature measurement and a gold disk as a radiation absorber. This paper presents recent advancements in the development of FOBs with reduced cooling time constants and enhanced temperature tolerance. We also demonstrate high-temperature operation and report findings from irradiation tests. By incorporating a copper sensor holder as a thermal sink and integrating two closely packed sensor heads into a compact design, the cooling time constants were reduced to ∼100 ms in vacuum, while minimizing uncertainties caused by temperature gradients. The FOBs were subjected to heating at 400 °C for five hours, with no observed degradation in noise performance post-heating. High-temperature operation tests were conducted at ∼220 °C using a 404 nm square-wave modulated laser to simulate the plasma radiation. In addition, four FOBs constructed from copper-coated pure-silica fibers were fabricated and underwent irradiation testing, enduring a total γ-radiation dose of 15.2 MGy and a neutron fluence of 1.6 × 10 18 n/cm 2 . As a result, the FOBs maintained their physical integrity and the optical signal shows high visibility throughout the test.

42 ENGINEERING↗
DOE OSTI2025

Replenishing liquid sheet targets to enable high-intensity high-repetition-rate laser–plasma interactions for ion-beam technology

We report on the development of a robust microfluidic nozzle capable of generating replenishing liquid sheet targets with sub-micron thickness at up to kHz repetition rates, a λ/20 surface flatness over areas of at least 100 μm 2 , and in-vacuum dimensions of 6 × 1.5 mm 2 . The platform was evaluated for stability under hundreds of 4.3 J laser shots at 0.5 Hz and 6 × 10 20 W/cm 2 peak intensity, delivered in burst mode, totaling 2.9 kJ on the target. The key metrics of the platform, including sheet characteristics, nozzle aperture morphology, and proton spectra, showed no measurable degradation in the performance of the liquid sheet platform following this experiment. Beyond its application to ion beam technology, we outline a pathway to further develop the capabilities of the platform into a high-repetition-rate plasma mirror.

depth profiling techniques↗
DOE OSTI2025

Laser wavelength dependence of laser imprint

In laser direct-drive inertial confinement fusion, laser imprint is one of the major causes of degradation in target performance through its seeding of hydrodynamic instabilities. Early experiments and simulations have shown that laser imprint could be mitigated with a longer laser wavelength because of its lower critical density and longer conduction zone. Building upon this work, we explore a scenario where the laser wavelength during the picket pulse differs from that of the main pulse in order to gain the benefit of reduced imprint, while avoiding losses in drive coupling efficiency or an increase in laser-plasma instabilities. A series of 2D radiation-hydrodynamic simulations, which test three different laser wavelengths for the picket pulse, has been performed, where the intensity of the picket pulse is adjusted in order to maintain the same implosion adiabat. A detailed analysis of the growth of the mass density modulations at the ablation front over a large range of mode numbers confirms that the laser imprint can be mitigated with a picket pulse operating at a longer wavelength than the main pulse because of the longer conduction zone and enhanced thermal smoothing. The amplitude of the ablation front modulations is found to be lower for all mode numbers, which reduces the seeding of the Rayleigh–Taylor instability without affecting the mode growth rates.

Fourier analysis↗