Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “morphology engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
NASA NTRS2016

Post-Flight Assessment of Avcoat Thermal Protection System for the Exploration Flight Test-1

On December 5, 2014 NASA conducted the first flight test of its next generation human-class Orion spacecraft. The flight was called the Exploration Flight Test -1 (EFT-1) which lasted for 4 hours and culminated into a re-entry trajectory at 9 km/s. This flight test of the 5-meter Orion Crew Module demonstrated various sub-systems including the Avcoat ablative thermal protection system (TPS) on the heat shield. The Avcoat TPS had been developed from the Apollo-era recipe with a few key modifications. The engineering for thermal sizing was supported by modeling, analysis, and ground tests in arc jet facilities. This paper will describe a postlfight analysis plan and present results from post-recovery inspections, data analysis from embedded sensors, TPS sample extraction and characterization in the laboratory. After the recovery of the vehicle, a full photographic survey and surface scans of the TPS were performed. The recovered vehicle showed physical evidence of flow disturbances, varying degrees of surface roughness, and excessive recession downstream of compression pads. The TPS recession was measured at more than 200 locations of interest on the Avcoat surface. The heat shield was then processed for sample extraction prior to TPS removal using the 7-Axis Milling machine at Marshall Space Flight Center. Around 182 rectangular TPS samples were extracted for subsequent analysis and investigation. The final paper will also present results of sample analysis. The planned investigation includes sidewall imaging, followed by image analysis to characterize TPS response by quantifying different layers in the char and pyrolysis zones. A full postmortem of the instrumentation and sensor ports will also be performed to confirm no adverse effects due to the sensors themselves. A subset of the samples will undergo structural testing and perform detailed characterization of any cracks and integrity of gore seams. Finally, the material will be characterized with layer-by-layer density measurements and SEM investigations to evaluate material morphology at microstructural level including identification of elements and compounds.

Aerothermodynamics↗
DOE OSTI2024

Microstructure analysis and machinability of additively manufactured A205 aluminum with heat treatments

A205 aluminum is one of the few high-strength aluminum alloys discovered for additive manufacturing (AM). The microstructure and heat treatment effects of AM A205 vary from those of its cast form, indicating possible differences in machinability during post-processing. Here, the objective of this research is to determine these variations of AM A205 and their effects on machinability using the cast condition as the baseline. As built and two heat-treated conditions (solution treatment and age hardening) were applied and compared in terms of their microstructures, micro-hardness, and machinability including vibration, specific cutting energy, chip morphology, and surface finish. The effects of print orientations on machinability were tested as well and found to be insignificant. AM as built had a higher hardness and slightly better machinability than its cast as built cast counterpart due to a smaller grain size (1 µm vs. 15 µm), eutectic θ-Al 2 Cu lattice and a fine, homogeneous TiB 2 distribution. The solution treatment dissolved this θ-Al 2 Cu lattice and increased the grain size (3 µm) which decreased the hardness, increased the ductility seen in the chips, and reduced the overall machinability. The presence of θ’-Al 2 Cu precipitates improved the machinability of aged AM A205. In addition, it was found that A205 exhibited both ductile and brittle behavior depending on the cutting speed, thus producing different machinability. The speed dependency is related to the material condition and heat treatment.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Electrochemically Grown Ultrathin Platinum Nanosheet Electrodes with Ultralow Loadings for Energy-Saving and Industrial-Level Hydrogen Evolution

Nanostructured catalyst-integrated electrodes with remarkably reduced catalyst loadings, high catalyst utilization and facile fabrication are urgently needed to enable cost-effective, green hydrogen production via proton exchange membrane electrolyzer cells (PEMECs). Herein, benefitting from a thin seeding layer, bottom-up grown ultrathin Pt nanosheets (Pt-NSs) were first deposited on thin Ti substrates for PEMECs via a fast, template- and surfactant-free electrochemical growth process at room temperature, showing highly uniform Pt surface coverage with ultralow loadings and vertically well-aligned nanosheet morphologies. Combined with an anode-only Nafion 117 catalyst-coated membrane (CCM), the Pt-NS electrode with an ultralow loading of 0.015 mg Pt cm -2 demonstrates superior cell performance to the commercial CCM (3.0 mg Pt cm -2 ), achieving 99.5% catalyst savings and more than 237-fold higher catalyst utilization. The remarkable performance with high catalyst utilization is mainly due to the vertically well-aligned ultrathin nanosheets with good surface coverage exposing abundant active sites for the electrochemical reaction. Overall, this study not only paves a new way for optimizing the catalyst uniformity and surface coverage with ultralow loadings but also provides new insights into nanostructured electrode design and facile fabrication for highly efficient and low-cost PEMECs and other energy storage/conversion devices.

42 ENGINEERING↗
DOE OSTI2025

Cryo-EM Visualization of Intermolecular π-Electron Interactions within π-Conjugated Peptidic Supramolecular Polymers

The self-assembly of “π-peptides” – molecules with π-electron cores substituted with two or more oligopeptide chains – brings organic electronic function into biologically relevant nanomaterials. π-Peptides assemble into fibrillar nanomaterials as driven by enthalpic peptide-based hydrogen bonding networks and pi-core-based quadrupolar interactions. A large body of spectroscopic, morphological and computational studies informs on the nature of the self-assembly process and the resulting nanostructures, but detailed structural information has remained elusive. Here, inspired by the recent use of cryogenic electron microscopy (cryo-EM) to provide high-resolution structures for synthetic peptide nanomaterials, we present here the use of cryo-EM to offer ca. 3 Å resolution of π-peptide nanomaterial assemblies, visualizing for the first time the nature of the intermolecular π-core electronic interactions responsible for energy transport through these supramolecular materials.

Group theory↗
DOE OSTI2024

Melt Pool characteristics on surface roughness and printability of 316L stainless steel in laser powder bed fusion

Purpose Surface quality and porosity significantly influence the structural and functional properties of the final product. This study aims to establish and explain the underlying relationships among processing parameters, top surface roughness and porosity level in additively manufactured 316L stainless steel. Design/methodology/approach A systematic variation of printing process parameters was conducted to print cubic samples based on laser power, speed and their combinations of energy density. Melt pool morphologies and dimensions, surface roughness quantified by arithmetic mean height (Sa) and porosity levels were characterized via optical confocal microscopy. Findings The study reveals that the laser power required to achieve optimal top surface quality increases with the volumetric energy density (VED) levels. A smooth top surface (Sa < 15 µm) or a rough surface with humps at high VEDs (VED > 133.3 J/mm 3 ) can serve as indicators for fully dense bulk samples, while rough top surfaces resulting from melt pool discontinuity correlate with high porosity levels. Under insufficient VED, melt pool discontinuity dominates the top surface. At high VEDs, surface quality improves with increased power as mitigation of melt pool discontinuity, followed by the deterioration with hump formation. Originality/value This study reveals and summarizes the formation mechanism of dominant features on top surface features and offers a potential method to predict the porosity by observing the top surface features with consideration of processing conditions.

Engineering↗
DOE OSTI2024

Data for Natural Deep Eutectic Solvents (NADES) Assisted Deconstruction of Oilcane Bagasse for High Lipid and Sugar Recovery

In a novel approach, metabolically engineered sugarcane “Oilcane” has been investigated for fractionation of lipid and cellulose-rich pulp, using certain Natural deep eutectic solvents (NADES). The exploration of eco-friendly solvents are at the forefront of harnessing the biofuel potential of modern bioenergy crops. For this, six combinations of NADES were prepared using choline chloride (ChCl) as HBA and lactic acid (LA), oxalic acid (OA) and glycerol (Gly) as HBD and were further explored for pretreatment of oilcane bagasse in a molar ratio of 1:1 and 1:2. The impact of NADES ratio, biomass loading (10–50%), residence time (1–2 h), and temperature (90–140 °C) were evaluated for delignification, lipid content, sugar release after enzymatic hydrolysis. The finding demonstrated that under the optimal condition of ChCl: LA (1:2 molar ratio), 140 °C with 2 h retention time, the lipid content in the pre-treated substrate was increased to 2.5-fold (∼8% w/w) and > 80% glucose yield was achieved after 72 h of hydrolysis of pre-treated bagasse. High solid loading (∼50%) during pretreatment resulted in a similar glucose yield. Furthermore, recycling studies demonstrated that nearly 95 to 98% NADES could be recycled after each pretreatment for up to five consecutive cycles without any significant loss in chemical structure as confirmed by 1H NMR and FT IR. FT IR and XRD analyses of native and pre-treated biomass were performed to visualize the morphological changes during NADES pretreatment and their impact on sugar yield. The findings of the study may be used to establish NADES-based biorefinery for the valorization of lipids, and carbohydrates for fuels and chemicals production.

Conversion↗
DOE OSTI2022

Application of GO anchored mediator in a polymer electrolyte membrane for high-rate solid-state supercapacitors

Here, we synthesized a novel polymer electrolyte membrane by combining poly (vinylidene fluoride) (PVDF) and lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) with graphene oxide (GO) nanosheets and a lithium salt of tungstosilicic acid (Li 4 SiW 12 O 40 , hereafter, referred to SiWLi). The impact of the addition of GO/SiWLi on the microstructure and morphology of the membrane were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), Fourier transform infrared spectroscopy (FTIR), and X-ray photoelectron spectroscopy (XPS). We found that adding the GO/SiWLi to the PVDF/LiTFSI polymer electrolyte membrane significantly reduced the pore size. Furthermore, the addition of the GO/SiWLi resulted in not only an increase of the ionic conductivity from 0.87 $\times$ 10 –2 to 3.12 $\times$ 10 –2 Scm –1 but also an increase in the lithium-ion transference number from 0.52 to 0.87. The polymer electrolyte membranes with and without GO/SiWLi were utilized to fabricate solid-state supercapacitors. The supercapacitors fabricated with the membrane containing GO/SiWLi displayed 37.2% lower equivalent series resistance and 88.2% greater specific capacitance than those fabricated using the membrane without GO/SiWLi at 200mVs –1 .

42 ENGINEERING↗
DOE OSTI2020

Self-Assembly of Silica Nanoparticles at Water–Hydrocarbon Interfaces: Insights from In Operando Small-Angle X-ray Scattering Measurements and Molecular Dynamics Simulations

To achieve tunable controls on the interactions of siliceous materials in subsurface environments bearing water and hydrocarbons, it is essential to determine the influence of hydrocarbon–water interfaces on the self-assembly of the silica particles. The hydrophilic silica particle have a tendency to aggregate on the water front of the interface. Self-assembly of silica nanoparticles proceeds via the migration of these nanoparticles to the water–hydrocarbon interface followed by aggregation at the interface. Fractal-like morphologies of assembled silica nanoparticles at water–hydrocarbon interfaces are observed. Rapid assembly of the hydrophilic silica nanoparticles at water–hydrocarbon interfaces corresponds to an overall reduction in the surface tension of water–toluene and water–heptane systems. These studies demonstrate the silica aggregation that is the precursor of silica polymerization, or nucleation and growth is influenced by the presence of hydrocarbons in subsurface geologic environments. These insights were derived from in operando ultrasmall and small-angle X-ray scattering (USAXS/SAXS) measurements, cryo-scanning electron microscopy (Cryo-SEM) imaging, and classical molecular dynamics simulations. As a result, these studies are intended to inform current and future efforts aimed at tuning silica reactivity in subsurface geologic environments to enhance permeability, the design and use of silica-based proppants to enhance fractures, and the development of effective strategies to control silica-based scaling behavior in subsurface reservoirs.

42 ENGINEERING↗
DOE OSTI2021

Energy balance in the DSSAT-CSM-CROPGRO model

One potential way to improve crop growth models is for the models to predict energy balance and evapotranspiration (ET) from first principles, thus serving as a check on “engineered” ET methodology. In this paper, we present new implementations and the results of an energy balance model (EBL) developed by Jagtap and Jones (1989) and then implemented in DSSAT’s CROPGRO (CG-EBL) model by Pickering et al. (1995) as a linked energy balance-photosynthesis model that has not been field-tested until now. The energy balance code computes evapotranspiration and other energy balance components, as well as a canopy air temperature, based on three sources (sunlit leaves, shaded leaves, soil surface). Model performance was evaluated with measured biomass and energy fluxes from two sites in Nebraska, namely, the US-Ne2 irrigated maize-soybean rotation field and the US-Ne3 rainfed maize-soybean rotation field, which are part of the Ameriflux eddy covariance network (htt ps://ameriflux.lbl.gov/sites). After implementing new aerodynamic resistances and the stomatal conductance model of the Ball–Berry–Leuning, crop growth, evapotranspiration and soil temperature were simulated well by the EBL model. The EBL improved ET predictions slightly over the often-used FAO56 method [Penman–Monteith (Allen et al., 1998)] for 4 of the 5 years evaluated for both irrigated and rainfed conditions. Further, a significant improvement was achieved using EBL for the simulation of soil temperature at the various depths compared to STEMP, the original subroutine in DSSAT for simulating soil temperature. Compared to the other available DSSAT methods, the EBL explicitly simulates the impacts of crop morphology, physiology and management on the crop’s environment and energy and mass exchange, which in turn directly affect the water use and irrigation requirements, phenology, photosynthesis, growth, sterility, and yield of the crop.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Thermal and radiation response of 4H–SiC Schottky diodes with direct-write electrical contacts

In this work, a high-sensitivity 4H–SiC temperature sensor and an alpha detector have been fabricated using additively printed metal contacts. The surface morphology and electrical conductivity of the printed electrodes were established prior to Schottky diode development. 4H–SiC Schottky diodes with direct-write printed silver contacts on the 5 μ m-thick epilayer on 4H–SiC were characterized electrically in terms of the forward and reverse current–voltage and high-frequency capacitance–voltage characteristics. Furthermore, the turn-on voltage of the Schottky diodes, as established from the forward current–voltage characteristics measured up to a temperature of 400 °C, showed a linear temperature dependence. Schottky diodes with direct-write printed Ag electrodes were able to measure alpha particles emitted from Americium-241. The high temperature and radiation response of the Schottky diodes show their suitability for multi-modal sensor fusion on the 4H–SiC platform for harsh environment applications.

42 ENGINEERING↗
DOE OSTI2024

Exploring the potential and impact of single-crystal active materials on dry-processed electrodes for high-performance lithium-ion batteries

Roll-to-roll powder-to-film dry processing (DP) and single-crystal (SC) active materials (AMs) with many advantages are two hot topics of lithium-ion batteries (LIBs). However, DP of SC AMs for LIBs is rarely reported. Consequently, the impact of SC AMs on dry-processed LIBs is not well understood. Herein, for the first time, via a set of experimental and theoretical studies of the conventional polycrystalline-AM- and SC-AM-based DPed electrodes (DPEs), this work not only reports a high-performance dry SC-AM cathode for LIB manufacturing, but also establishes some fundamental understanding of SC-based dry-processed electrodes, including their morphology, structure, mechanical strength, electronic conductivity and LIB electrochemical behavior. Further, the results suggest that DP of SC AMs is promising, which can dramatically improve the electrochemical kinetics at electrode level and particle level. Specifically, for the rate capability and long-term cyclability in full cells, SC DPEs exhibit a discharge specific capacity of 152.1 mAh g -1 at 1C and a capacity retention rate of 79.9 % at C/3 over 500 cycles, which are superior to those of PC DPEs (135.6 mAh g -1 and 68.3 %) at the same conditions and are further confirmed by the simulation data from the theoretical modelling study. Therefore, this comprehensive work marks a significant milestone for DP strategy and SC AMs, enlightening future research and development of LIB manufacturing.

25 ENERGY STORAGE↗
DOE OSTI2025

Impacts of Lanthanum Impurities on Nickel-Rich Cathode Materials

The widespread use of lithium-ion batteries (LIBs) has led to environmental concerns and exacerbated the scarcity of essential minerals, underscoring the urgent need for effective recycling strategies. Among various recycling methods, the hydrometallurgical process is distinguished by its energy efficiency and minimal environmental impact. Nickel-metal hydride (Ni-MH) batteries are a significant source of nickel sulfate (NiSO 4 ) for hydrometallurgical recycling due to their substantial nickel content. A significant challenge arises from the effective separation of lanthanum (La), which results in at least 20 ppm of La being present in the recycled NiSO 4 . This study explores a critical aspect of the recycling process: the impact of La 3+ impurities, introduced through recycled NiSO 4 , on the performance of the synthesized nickel-rich cathode materials. We conducted a thorough investigation into how La 3+ influences morphology and structural integrity during both the synthesis of precursors and the production of cathode materials. Our findings indicate that La 3+ impurities do not adversely affect the morphology or structural integrity of the cathode precursors relative to virgin materials. However, higher concentrations of La 3+ reduce the discharge capacity with enhanced cycle stability by minimizing cation mixing between lithium (Li + ) and nickel (Ni 2+ ) ions within the cathode. Furthermore, this stability is crucial for extending battery life. Therefore, controlling the concentration of La 3+ impurities is essential for optimizing the electrochemical performance of recycled cathode materials.

Corrosion↗
DOE OSTI2022

Influence of Cryomilling on Crystallite Size of Aluminum Powder and Spark Plasma Sintered Component

The present investigation aims to develop nanocrystalline (NC) pure aluminum powders using cryomilling technique and manufacture bulk components using spark plasma sintering (SPS). The cryomilling was performed on pure Al powders for 2, 6, and 8 h. The cryomilled powders were then consolidated using SPS to produce bulk components. The particle morphology and crystallite size of the powders and the bulk SPS components were analyzed using scanning electron microscopy (SEM), X-ray diffraction (XRD), and transmission electron microscopy (TEM). The results showed that the crystallite size of pure Al powders decreases with increased cryomilling time. The results also showed that the SPS at elevated temperatures resulted in a slight increase in crystallite size, however, the changes were insignificant. The mechanical properties of the bulk components were determined using a Vickers microhardness tester. The hardness of the cryomilled SPS component was determined to be three times higher than that of the unmilled SPS component. The mechanism for the reduction in crystallite size with increasing cryomilling time is discussed. This fundamental study provides an insight into the development of bulk nanomaterials with superior mechanical properties for automotive, aerospace, marine, and nuclear applications.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Kinetic model describing self-limiting CO 2 diffusion in supported amine adsorbents

A reaction–diffusion shrinking core model describing the decay in diffusivity of supported amine sorbents upon CO 2 sorption under both simulated direct air capture and point source capture conditions is described. The decay in CO 2 diffusivity is associated with crosslinking in the aminopolymer samples and general pore blockage in the amino-silane derived samples, which occurs as CO 2 is adsorbed. The model is used to extract four kinetic parameters that govern the CO 2 uptake kinetics and working capacity: an apparent reaction rate constant, an initial effective diffusivity, and two dimensionless decay parameters. Ideally, an initially reaction limited system would allow for direct determination of the intrinsic reaction rate constant; however, sorption experiments suggest mass transfer resistances related to gas mixing, external boundary layers and intraparticle diffusion are present. Reaction rate constants are determined and agree well with theoretical values predicted with the Eyring equation parameterized using density functional theory energies from literature sources. The kinetic performance is expressed as the average effective diffusivity as a function of average conversion, which can be correlated to the dispersion of sorption sites on the support and the morphology of the active sorbent phase. Four supports are impregnated or grafted with amines, SBA-15, single-walled zeolite nanotubes (ZNT), Syloid SiO 2 , and γ-Al 2 O 3 . Due to its pore structure, γ-Al 2 O 3 supported amines can be modeled at the μm scale or at the nm scale, where the shell balance is on the μm-sized macroporous particle aggregate or on the nm-sized amine film on the surface of the Al 2 O 3 nanoparticles, which comprise the spherical particle aggregates. Faster diffusion rates are maintained under 400 ppm rather than 10% CO 2 due to a slower reaction rate giving a slower decay in diffusivity. In conclusion, this work provides a first principles kinetic analysis of CO 2 sorption where previous models are semi-empirical and use arbitrary kinetic parameters.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Gas Hydrate Film Growth in Microfluidic Channels for Carbon Dioxide Capture and Sequestration Applications

Gas or clathrate hydrates are a solid, crystalline compound composed of water and guest molecules that typically form at high pressure and low temperature conditions. Carbon dioxide (CO2) hydrates may be involved in several carbon dioxide capture and sequestration (CCS) applications, including CO2 pipeline transportation and CO2 offshore sequestration. Within these applications, the formation mechanism and kinetics must be well understood to manage the CCS processes, either by preventing or promoting hydrate formation. In this work, a high-pressure glass microfluidic reactor is used in tandem with visual microscopy and in-situ Raman spectroscopy to study both the morphological and kinetic behavior of gas hydrate crystals. Subcooling, pressure, and CO2 flow rate are investigated for their impact on the thickening behavior of pure CO2 hydrates, with flow rate being the only parameter to have a significant effect. Visual and Raman spectroscopy evidence show that both a dense hydrate layer and a porous hydrate layer form, and the latter may provide a path for mass transfer to continue hydrate crystallization. A first principles mass transfer model is developed to describe CO2 hydrate crystal thickening at the interface between gas and water. The impacts of gas impurities and channel wettability are also studied. This method is further applied to investigate the conversion of methane hydrate to CO2 hydrate for combined energy recovery and methane hydrate formation. The authors acknowledge the US Department of Energy Basic Energy Science award # DE-SC0022162.

Wadsworth, Lindsey [Colorado School of Mines, Gold↗
DOE OSTI2024

Smart manufacturing approach to manufacture bulk nanocrystalline aluminum for lightweight applications

In this research, a smart manufacturing approach was used to enhance the mechanical properties of aluminum (Al) for lightweight applications. The smart manufacturing involved cryomilling of Al powders with and without 5 wt.% magnesium (Mg) powders for varying durations followed by a high-pressure cold spray (HPCS) additive manufacturing process to prepare bulk components. The morphological changes, crystallite size, and composition of the cryomilled powders and cold sprayed (CS’ed) components were examined using scanning electron microscopy (SEM), x-ray diffraction (XRD), and transmission electron microscopy (TEM) techniques. The results showed that the crystallite size reduces with an increase in cryomilling time and the addition of Mg dopant. To test the mechanical properties of the bulk CS’ed components, microhardness tests were performed using a Vickers microhardness tester. Uniaxial tensile tests were also carried out to ascertain the material’s tensile properties. The mechanical testing results showed great improvement in the hardness and tensile strength of CS’ed Al–Mg samples as compared to pure Al samples. Subsequently, fractography analysis of the tensile failed samples was carried out to determine the nature of the failure. Here, the research article also discusses the inherent mechanisms for the improvement in mechanical properties of smart manufactured components as a result of Mg doping and cryomilling.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Optimizing spectral and morphological match of nonfullerene acceptors toward efficient indoor organic photovoltaics with enhanced light source adaptability

High-performance indoor organic photovoltaics (IOPV) require large-bandgap material systems to absorb visible light efficiently and reduce energy loss. However, state-of-the-art non-fullerene acceptors (NFAs) have absorptions in the near-infrared region and are thus not suitable for IOPV applications. Herein, we report a series of large-bandgap (>1.70 eV) NFAs named FCC-Cl-C8, FCC-Cl-4Ph and FCC-Cl-6Ph by modifying the alkyl side chains with alkylphenyl chains partially or completely. Results show that the bulky alkylphenyl side chains can finely tune the absorption properties of the NFAs and also affect their morphological properties. Interestingly, the best-performing NFA is the one (named FCC-Cl-4Ph) with partial alkyl and alkylphenyl substitutions, which blue-shift the absorption of the NFAs while minimizing the negative morphological effect of the bulky alkylphenyl chains. As a result, FCC-Cl-4Ph can achieve excellent indoor efficiencies over 29% under a 3000 K LED lamp at 1000 lux and show better solution processability over FCC-Cl-C8. More importantly, FCC-Cl-4Ph can maintain high indoor performance (29.7–26.8% at 1000 lux) under a wide range of indoor lighting spectra (2600, 3000, 4000, and 6500 K LED lamps), which should be due to the blue-shifted spectra of FCC-Cl-4Ph and better matching with various indoor conditions. Finally, this work reveals an interesting structure-property relationship and offers useful strategies for the further design of NFAs toward efficient IOPV devices.

14 SOLAR ENERGY↗
DOE OSTI2021

The Effect of Topology on Phase Behavior under Confinement

This work studies how morphology (i.e., the shape of a structure) and topology (i.e., how different structures are connected) influence wall adsorption and capillary condensation under tight confinement. Numerical simulations based on classical density functional theory (cDFT) are run for a wide variety of geometries using both hard-sphere and Lennard-Jones fluids. These cDFT computations are compared to results obtained using the Minkowski functionals. It is found that the Minkowski functionals can provide a good description of the behavior of Lennard-Jones fluids down to small system sizes. In addition, through decomposition of the free energy, the Minkowski functionals provide a good framework to better understand what are the dominant contributions to the phase behavior of a system. Lastly, while studying the phase envelope shift as a function of the Minkowski functionals it is found that topology has a different effect depending on whether the phase transition under consideration is a continuous or a discrete (first-order) transition.

42 ENGINEERING↗