Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “mixed effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Residual thermal and moisture influences on the free-edge delamination of laminated composites

A simple delamination analysis method is developed. It is based on a shear-type deformation theory and includes hygrothermal effects. The method is applied to mixed-mode edge delamination specimens made of T300/5208 graphite/epoxy. It is found that residual thermal influences were alleviated when moisture stresses were included. Thermal effects on the interlaminar shear stress and total energy release rate were totally alleviated for the same specific moisture content. Moreover, this value of moisture content was not significantly affected by the stacking sequence for the laminates considered.

Armanios, Erian A.↗
NASA NTRS1985

Mixing layer control for tangential slot injection in turbulent flows

Tangential injection into turbulent flows is one of the most promising methods of minimizing skin friction and providing thermal protection. The technique also has application to laser hardening. The effectiveness of the injected material can be increased if the spreading rate of the resulting mixing region can be reduced. Various techniques which have been shown to be effective in manipulating the rate of growth of mixing layers under certain conditions have been applied to a slot configuration having a thick external turbulent boundary layer. These include geometry modifications to the slot lip trailing edge and acoustic excitation of the slot exit plane over a wide range of frequencies. Neither of these approaches produced any noticeable effect on the downstream evolution of the mixing layer. This lack of effectiveness is attributed to the dominating influence of the well-developed incoming turbulent boundary layer. The placement of large-eddy breakup devices in this boundary layer upstream of the injection point did produce significantly lower velocities in the near-wall region of the flow downstream of the slot exit.

Mcinville, R. M.↗
NASA NTRS1992

Characterization of supersonic mixing in a nonreacting Mach 2 combustor

Planar measurements of the injection mole fraction distribution and the velocity field within a nonreacting model SCRAMJET combustor have been made using laser-induced iodine fluorescence. The combustor geometry investigated in this work is staged transverse injection of air into a Mach 2 freestream. A complete three-dimensional survey of the injectant mole fraction distribution has been generated and a single planar velocity measurement has been completed. The measurements reveal the dramatic effect of streamwise vortices on the mixing of the injectant in the near field of the injectors, as well as the rapid mixing generated by staging two field injectors. Analysis of the downstream decay of the maximum injectant mole fraction in this and other nonreacting combustor geometries indicates that the relative rate of injectant mixing well downstream of the injectors is independent of combustor geometry, combustor Mach number, and injectant molecular weight. Mixing within this region of the combustor is dominated by turbulent diffusion within the injectant plume. The transition of the dominant mixing mechanism, from vortex-driven mixing in the near field to turbulent diffusion in the far field, was found to occur in the region between 10 and 20 jet diameters downstream of the injectors.

Hollo, Steven D.↗
NASA NTRS1994

Quantitative investigation of compressible mixing: Staged transverse injection into Mach 2 flow

Planar measurements of the injectant mole fraction distribution and the velocity field within a supersonic mixing flowfield have been made using laser-induced iodine fluorescence. The flowfield investigated in this work is staged transverse injection of air into a Mach 2 freestream. A complete three-dimensional survey of the injectant mole fraction distribution has been generated, and a single planar velocity measurement has been completed. The measurements reveal the dramatic effect of streamwise vortices on the mixing in the near field of the injectors, as well as the rapid mixing generated by staging two fuel injectors. Analysis of the downstream decay of the maximum injectant mole fraction in this and other supersonic mixing flowfields indicates that the relative rate of injectant mixing well downstream of the injectors is independent of injection geometry, freestream Mach number, and injectant molecular weight. Mixing within this region of the flowfield is dominated by small-scale turbulence within the injectant plume. The transition of the dominant mixing mechanism, from vortex-driven mixing in the near field to small-scale turbulent mixing in the far field, was found to occur in the region about 10 diameters downstream of the injectors.

Hollo, Steven D.↗
NASA NTRS1994

Comparison of Mixing Calculations for Reacting and Non-Reacting Flows in a Cylindrical Duct

A production 3-D elliptic flow code has been used to calculate non-reacting and reacting flow fields in an experimental mixing section relevant to a rich burn/quick mix/lean burn (RQL) combustion system. A number of test cases have been run to assess the effects of the variation in the number of orifices, mass flow ratio, and rich-zone equivalence ratio on the flow field and mixing rates. The calculated normalized temperature profiles for the non-reacting flow field agree qualitatively well with the normalized conserved variable isopleths for the reacting flow field indicating that non-reacting mixing experiments are appropriate for screening and ranking potential rapid mixing concepts. For a given set of jet momentum-flux ratio, mass flow ratio, and density ratio (J, MR, and DR), the reacting flow calculations show a reduced level of mixing compared to the non-reacting cases. In addition, the rich-zone equivalence ratio has noticeable effect on the mixing flow characteristics for reacting flows.

Oechsle, V. L.↗
NASA NTRS1977

Wash water waste pretreatment system

Investigations were completed on wash waters based on each candidate personal cleansing agent. Evaluations of coagulants, antifoam agents, and the effect of promising antifoams on the chemical precipitation were included. Based on these evaluations two candidate soaps as well as their companion antifoam agents were selected for further work. Operating parameters included the effect of soap concentration, ferric chloride concentration, duration of mixing, and pore size of depth filters on the degree of soap removal. The effect of pressure on water flow through filter cartridges and on the rate of decline of water flow was also investigated. The culmination of the program was the recommendation of a pretreatment concept based on chemical precipitation followed by pressure filtration.

Source record↗
NASA NTRS1996

Identifying yield-optimizing environments for two cowpea breeding lines by manipulating photoperiod and harvest scenario

Photoperiod and harvest scenario of cowpea (Vigna unguiculata L. Walp) canopies were manipulated to optimize productivity for use in future controlled ecological life-support systems. Productivity was measured by edible yield rate (EYR:g m-2 day-1), shoot harvest index (SHI: g edible biomass [g total shoot dry weight]), and yield-efficiency rate (YER:g edible biomass m-2 day-1 per[g nonedible shoot dry weight]). Breeding lines 'IT84S-2246' (S-2246) and "IT82D-889' (D-889) were grown in a greenhouse under 8-, 12-, or 24-h photoperiods. S-2246 was short-day and D-889 was day-neutral for flowering. Under each photoperiod, cowpeas were harvested either for leaves only, seeds only, or leaves plus seeds (mixed harvest). Photoperiod did not affect EYR of either breeding line for any harvest scenario tested. Averaged over both breeding lines, seed harvest gave the highest EYR at 6.7 g m-2 day-1. The highest SHI (65%) and YER (94 mg m-2 day-1 g-1) were achieved for leaf-only harvest of D-889 under an 8-h photoperiod. For leaf-only harvest of S-2246, both SHI and YER increased with increasing photoperiod, but declined for seed-only and mixed harvests. However, photoperiod had no effect on SHI or YER for D-889 for any harvest scenario. A second experiment utilized the short-day cowpea breeding line 'IT89KD-288' (D-288) and the day-neutral breeding line 'IT87D-941-1' (D-941) to compare yield parameters using photoperiod extension under differing lamp types. This experiment confirmed the photoperiod responses of D-889 and S-2246 to a mixed-harvest scenario and indicated that daylength extension with higher irradiance from high pressure sodium lamps further suppressed EYR, SHI, and YER of the short-day breeding line D-288.

Non-NASA Center↗
NASA NTRS1991

Evolution of three-dimensionality in stable and unstable curved mixing layers

Results are presented of an experimental study tracing the effects of mild streamwise curvature (delta/R is less than 5 percent) on the 3D structure of a two-stream mixing layer at high Reynolds number (about 27,000). Measurements of the mean and fluctuating velocities were obtained on fine cross-plane grids at 11 streamwise locations using a rotatable cross-wide probe. Well-organized streamwise vorticity was generated in both cases through the braid instability. Although the vortex structures decayed with streamwise distance in both cases, the rate of decay for the unstable case was lower. As a result, the unstable layer exhibited noticeable spanwise variations in the mean velocity and Reynolds stresses. Both cases achieved linear growth, but the rate of growth for the unstable case was higher. The far-field spanwise-averaged peak Reynolds stresses were significantly higher for the destabilized case compared to the stabilized case, which exhibited levels comparable to those of a straight case.

Plesniak, Michael W.↗
NASA NTRS1994

Reevaluation of the NOAA/CMDL carbon monoxide reference scale and comparisons with CO reference gases at NASA-Langley and the Fraunhofer Institut

The carbon monoxide (CO) reference scale created by the National Oceanic and Atmospheric Administration/Climate Monitoring and Diagnostics Laboratory (NOAA/CMDL) is used to quantify measurements of CO in the atmosphere, calibrate standards of other laboratories and to otherwise provide reference gases to the community measuring atmospheric CO. This reference scale was created based upon a set of primary standards prepared by gravimetric methods at CMDL and has been propagated to a set of working standards. In this paper we compare CO mixing ratios assigned to the working standards by three approaches: (1) calibration against the original gravimetric standards, (2) calibration using only working standards as the reference gas, and (3) calibration against three new gravimetric standards prepared to CMDL. The agreement between these values was typically better than 1%. The calibration histories of CMDL working standards are reviewed with respect to expected rates of CO change in the atmosphere. Using a Monte Carlo approach to simulate the effect of drifting standards on calculated mixing ratios, we conclude that the error solely associated with the maintenance of standards will limit the ability to detect small CO changes in the atmosphere. We also report results of intercalibration experiments conducted between CMDL and the Diode Laser Sensor Group (DACOM) at the NASA Langley Research Center (Hampton, Virginia), and CMDL and the Fraunhofer-Institut (Garmisch-Partenkirchen, Germany). Each laboratory calibrated several working standards for CO using their reference gases, and these results were compared to calibrations conducted by CMDL. The intercomparison of eight standards (CO concentrations between approximately 100 and approximately 165 ppb) by CMDL and NASA agreed to better than +/- 2%. The calibration of six standards (CO concentrations between approximately 50 and approximately 210 ppb) by CMDL and the Fraunhofer-Institut agreed to within +/- 2% for four standards, and to within +/- 5% for all six standards.

Novelli, P. C.↗
NASA NTRS1977

Atmospheric effects on inlets for supersonic cruise aircraft

Mixed-compression inlet dynamic behavior in the vicinity of unstart, was simulated and analyzed to investigate time response of an inlet's normal shock to independent disturbances in ambient temperature and pressure and relative velocity (longitudinal gust), with and without inlet controls active. The results indicate that atmospheric disturbances may be more important than internal disturbances in setting inlet controls requirements because they are usually not anticipated and because normal shock response to rapid atmospheric disturbances is not attenuated by the inlet, as it is for engine induced disturbances. However, before inlet control requirements can be fully assessed, more statistics on extreme atmospheric disturbances are needed.

Cole, G. L.↗
NASA NTRS1998

Modeling of a Two-Phase Jet Pump with Phase Change, Shocks and Temperature-Dependent Properties

One of the primary motivations behind this work is the attempt to understand the physics of a two-phase jet pump which constitutes part of a flow boiling test facility at NASA-Marshall. The flow boiling apparatus is intended to provide data necessary to design highly efficient two-phase thermal control systems for aerospace applications. The facility will also be capable of testing alternative refrigerants and evaluate their performance using various heat exchangers with enhanced surfaces. The test facility is also intended for use in evaluating single-phase performance of systems currently using CFC refrigerants. Literature dealing with jet pumps is abundant and covers a very wide array of application areas. Example application areas include vacuum pumps which are used in the food industry, power station work, and the chemical industry; ejector systems which have applications in the aircraft industry as cabin ventilators and for purposes of jet thrust augmentation; jet pumps which are used in the oil industry for oil well pumping; and steam-jet ejector refrigeration, to just name a few. Examples of work relevant to this investigation includes those of Fairuzov and Bredikhin (1995). While past researchers have been able to model the two-phase flow jet pump using the one-dimensional assumption with no shock waves and no phase change, there is no research known to the author apart from that of Anand (1992) who was able to account for condensation shocks. Thus, one of the objectives of this work is to model the dynamics of fluid interaction between a two-phase primary fluid and a subcooled liquid secondary fluid which is being injected employing atomizing spray injectors. The model developed accounts for phase transformations due to expansion, compression, and mixing. It also accounts for shock waves developing in the different parts of the jet pump as well as temperature and pressure dependencies of the fluid properties for both the primary two-phase mixture and the secondary subcooled liquid. The research effort on which this document partly reports described a relatively simple model capable of describing the performance of a two-phase flow jet pump. The model is based on the isentropic homogeneous expansion/compression hypothesis and is capable of fully incorporating the effects of shocks in both the mixing chamber and the throat/diffuser parts of the pump. The physical system chosen is identical to that experimentally tested by Fairuzov and Bredikhin (1995) and should therefore be relatively easy to validate.

Sherif, S. A.↗
NASA NTRS1997

A Modified Linear-Mixing Method for Calculating Atmospheric Path Radiances of Aerosol Mixtures

The top-of-atmosphere (TOA) path radiance generated by an aerosol mixture can be synthesized by linearly adding the contributions of the individual aerosol components, weighted by their fractional optical depths. The method, known as linear mixing, is exact in the single-scattering limit. When multiple scattering is significant, the method reproduces the atmospheric path radiance of the mixture with less than 3% errors for weakly absorbing aerosols up to optical thickness of 0.5. However, when strongly absorbing aerosols are included in the mixture, the errors are much larger. This is due to neglecting the effect of multiple interactions between the aerosol components, especially when the values of the single-scattering albedos of these components are so different that the parameter e = the sum of f(sub i)[(bar)omega(sub i) - (bar)omega(sub mix)]/(bar)omega(sub i) is larger than approximately 0.1, where (bar)omega(sub i)and f(sub i) are the single-scattering albedo and the fractional abundance of the ith component, and (bar)omega(sub mix) is the effective single-scattering albedo of the Mixture. We describe an empirical, modified linear-mixing method which effectively accounts for the multiple interactions between aerosol components. The modified and standard methods are identical when epsilon = 0.0 and give similar results when epsilon is less than or equal to 0.05. For optical depths larger than approximately 0.5, or when epsilon is greater than 0.05, only the modified method can reproduce the radiances within 5% error for common aerosol types up to optical thickness of 2.0. Because this method facilitates efficient and accurate atmospheric path radiance calculations for mixtures of a wide variety of aerosol types, it will be used as part of the aerosol retrieval methodology for the Earth Observing System (EOS) multiangle imaging spectroradiometer (MISR), scheduled for launch into polar orbit in 1998.

Abdou, W. A.↗
NASA NTRS1984

Embedded shear layer computations for increased drag reduction

One of the most promising methods of minimizing drag is the reduction of skin friction by injection of low momentum fluid into the near-wall region of turbulent boundary layer flows. This method could be made more effective by limiting the spread rate of the resulting mixing region. In order to achieve a better understanding of how this goal might be achieved, numerical investigations of the relevant fluid dynamic processes governing these regions have been conducted. A compact finite-difference algorithm has been applied to the complete form of the governing conservation equations for a two-dimensional laminar mixing layer. The ability of this computational approach to model successfully the formation and interaction of the large scale vortical structures which dominate such flow fields is verified in the present study. Parameters which affect the spread rate of the mixing region are also identified. In addition, the relative importance of viscous and momentum transport effects in the vortex interactions is determined.

Gatski, T. B.↗
NASA NTRS1994

Investigation of ramp injectors for supersonic mixing enhancement

A comparative study of wall mounted swept ramp injectors fitted with injector nozzles of different shape has been conducted in a constant area duct to explore mixing enhancement techniques for scramjet combustors. Six different injector nozzle inserts, all having equal exit and throat areas, were tested to explore the interaction between the preconditioned fuel jet and the vortical flowfield produced by the ramp: circular nozzle (baseline), nozzle with three downstream facing steps, nozzle with four vortex generators, elliptical nozzle, tapered-slot nozzle, and trapezoidal nozzle. The main flow was air at Mach 2, and the fuel was simulated by air injected at Mach 1.63 or by helium injected at Mach 1.7. Pressure and temperature surveys, combined with Mie and Rayleigh scattering visualization, were used to investigate the flow field. The experiments were compared with three dimensional Navier-Stokes computations. The results indicate that the mixing process is dominated by the streamwise vorticity generated by the ramp, the injectors' inner geometry having a minor effect. It was also found that the injectant/air mixing in the far-field is nearly independent of the injector geometry, molecular weight of the injectant, and the initial convective Mach number.

Haimovitch, Y.↗
NASA NTRSDate not supplied

Microbial Mutualism in (Modeled) Microgravity: Measuring the Effects of A Spaceflight-Like Fluid Environment on Cross-Feeding Communities

Microorganisms grow differently in spaceflight than they do on Earth. While numerous factors likely contribute, one ubiquitous feature of the space environment is altered gravity - but because microbes are generally considered too small to detect gravity directly, they likely experience the effects of gravity via changes in their fluid environment, primarily a reduction in convective mixing. This theory is supported by evidence that individual microbial strains experience starvation and acid stress in microgravity. If it is true, then microgravity would also have measurable effects on microbes in mixed communities, because many interspecies interactions involve the exchange of soluble metabolites through their medium (cross-feeding). Specifically, cooperative cross-feeding communities would grow more slowly in microgravity, and this effect should be reproducible in ground-based rotational culture systems (rotating wall vessels, RWVs) designed to simulate the quiescent environment of microgravity. Here we present preliminary results of our efforts to test this hypothesis using using a model system of Eschericia coli and Salmonella enterica that grow only when they can exchange methionine and acetate through the medium. We report on the development of a novel laboratory system that allows us measure growth rates and species ratios in real-time using fluorescence spectrometry as the organisms grow in RWVs. We are able to track growth rates of individual species and the co-culture continuously with high temporal resolution for several hours, a substantial improvement over prior RWV systems that require destructive sampling. We vary the fidelity of the microgravity simulation by varying the rotation rate, and find that rotation rate affects growth rates of the community more than that of individual strains, consistent with the claim that RWVs can simulate a microgravity-like quiescent environment. While more work needs to be done to probe the mechanisms of this effect, we hope that our system will ultimately allow us to generate quantitative predictions about the effects of spaceflight on organisms that are tiny but essential to sustaining long-term human space exploration.

microgravity↗
NASA NTRS1993

Numerical simulation of non-Newtonian free shear flows

Free shear flows, like those of mixing layers, are encountered in aerodynamics, in the atmosphere, and in the ocean as well as in many industrial applications such as flow reactors or combustion chambers. It is, therefore, crucial to understand the mechanisms governing the process of transition to turbulence in order to predict and control the evolution of the flow. Delaying transition to turbulence as far downstream as possible allows a gain in energy expenditure while accelerating the transition can be of interest in processes where high mixing is desired. Various methods, including the use of polymer additives, can be effective in controlling fluid flows. The drag reduction obtained by the addition of small amounts of high polymers has been an active area of research for the last three decades. It is now widely believed that polymer additives can affect the stability of a large variety of flows and that dilute solutions of these polymers have been shown to produce drag reductions of over 80 percent in internal flows and over 60 percent in external flows under a wide range of conditions. The major thrust of this work is to study the effects of polymer additives on the stability of the incompressible mixing layer through large scale numerical simulations. In particular, we focus on the two dimensional flow and examine how the presence of viscoelasticity may affect the typical structures of the flow, namely roll-up and pairing of vortices.

Homsy, G. M.↗
NASA NTRS2017

How the Emitted Size Distribution and Mixing State of Feldspar Affect Ice Nucleating Particles in a Global Model

The effect of aerosol particles on ice nucleation and, in turn, the formation of ice and mixed phase clouds is recognized as one of the largest sources of uncertainty in climate prediction. We apply an improved dust mineral specific aerosol module in the NASA GISS Earth System ModelE, which takes into account soil aggregates and their fragmentation at emission as well as the emission of large particles. We calculate ice nucleating particle concentrations from K-feldspar abundance for an active site parameterization for a range of activation temperatures and external and internal mixing assumption. We find that the globally averaged INP concentration is reduced by a factor of two to three, compared to a simple assumption on the size distribution of emitted dust minerals. The decrease can amount to a factor of five in some geographical regions. The results vary little between external and internal mixing and different activation temperatures, except for the coldest temperatures. In the sectional size distribution, the size range 24 micrometer contributes the largest INP number.

Perlwitz, Jan P.↗