Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “mixed conduction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

The effect of incomplete fuel-air mixing on the lean limit and emissions characteristics of a Lean Prevaporized Premixed (LPP) combustor

Results are presented from an experimental study of the effect of incomplete fuel-air mixing on the lean limit and emissions characteristics of a lean, prevaporized, premixed (LPP), coaxial mixing tube combustor. Two-dimensional exciplex fluorescence was used to characterize the degree of fuel vaporization and mixing at the combustor inlet under non-combusting conditions. These tests were conducted at a pressure of 4 atm., a temperature of 400 C, a mixer tube velocity of 100 m/sec and an equivalence ratio of .8, using a mixture of tetradecane, 1 methyl naphthalene and TMPD as a fuel simulant. Fuel-air mixtures with two distinct spatial distributions were studied. The exciplex measurements showed that there was a significant amount of unvaporized fuel at the combustor entrance in both cases. One case, however, exhibited a very non-uniform distribution of fuel liquid and vapor at the combustor entrance, i.e., with most of the fuel in the upper half of the combustor tube, while in the other case, both the fuel liquid and vapor were much more uniformly distributed across the width of the combustor entrance. The lean limit and emissions measurements were all made at a pressure of 4 atm. and a mixer tube velocity of 100 m/sec, using Jet A fuel and both fuel-air mixture distributions. Contrary to what was expected, the better mixed case was found to have a substantially leaner operating limit. The two mixture distributions also unexpectedly resulted in comparable NO(x) emissions, for a given equivalence ratio and inlet temperature, however, lower NO(x) emissions were possible in the better mixed case due to its leaner operating limit.

Santavicca, D. A.↗
DOE OSTI2020

Sorption Enhanced Mixed Matrix Membranes for Hydrogen (H 2 ) Purification and Carbon Dioxide (CO 2 ) Capture

The technical objective of this project was to develop sorption enhanced mixed matrix membranes with H 2 permeance of 500 gas permeance units (GPU) and H 2 /CO 2 selectivity of 30 at 150-200 °C. These membranes will be the central component in the design of membrane based systems for 90% capture of CO 2 from coal-derived syngas, with 95% CO 2 purity at a cost of electricity 30% less than baseline capture approaches. The unique approach in this proposal is to design crosslinked polymers containing Pd-based nanoparticles achieving strong H 2 sorption and size sieving ability and thus H 2 /CO 2 selectivity. The specific objectives for each budget period (BP) are described below. BP 1: Identify polymer matrix with strong size sieving ability and palladium (Pd)-containing nanomaterials to prepare freestanding mixed matrix films with H 2 permeability of 50 Barrer and H 2 /CO 2 selectivity of 30 at 150-200°C with simulated syngas. BP 2: Prepare and optimize thin film mixed matrix composite membranes materials with H 2 permeance of 500 GPU and H 2 /CO 2 selectivity of 30 at 150-200 °C, and complete the modification of the membrane test unit for the field test in the BP 3. BP 3: Conduct a 20-day field test of the membranes with real syngas at Center for Advanced Energy Research (CAER) of the University of Kentucky (UKy). During the BP2, we have successfully prepared thin-film composite (TFC) membranes based on mixed matrix materials (MMMs) containing Pd nanoparticles in polymers, and demonstrated their superior and robust performance for H 2 /CO 2 separation at 150 – 225 °C. (1) Production of the Pd based nanoparticles with a diameter of 4 nm has been scaled up to 200 mg/day. (2) We have prepared TFC membranes with H 2 permeance above 500 GPU and H 2 /CO 2 selectivity above 30 at temperatures up to 225 °C, which meet the targets for the BP2. (3) We have conducted parametric studies of TFC membranes with a mixed gas containing H 2 S and H 2 O and demonstrated the stability of the membranes. (4) We have established a new testing plan at the Center for Advanced Energy Studies (CAER) at the University of Kentucky because NCCC decided to shut down their gasifier. During this project, four Ph.D. students received the inter-disciplinary training and graduated, including Shailesh Konda, Maryam Omidvar, Deqiang Yin, and Lingxiang Zhu. One postdoctoral researcher (Dr. Liang Huang) and two Ph.D. students (Abhishek Kumar and Hien Nguyen) are involved in this project. The project leads to one provisional patent application, eight peer-reviewed articles, and one manuscript in preparation. The details are shown below.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2022

Produced Water and Waste Heat-aided Blowdown Water Treatment: Using Chemical and Energy Synergisms for Value Creation

The project objective was to develop a cooling blowdown water (BDW) treatment process utilizing produced water (PW) and low-grade heat to maximize water reuse and saleable by-product generation while reducing chemical and energy footprints of the treatment. The proposed treatment process consists of mixing, softening, organics and suspended solids removal, reverse osmosis (RO), thermal desalination, and brine electrolysis. BDW samples collected from a local coal-fired power plant and PW samples from two shale gas production wells were used in this study. Each treatment unit was first designed and tested to quantify its treatment efficiency, and its chemical and energy requirements. In addition, a process model was developed and model simulations were conducted based on the experimental results and literature data to optimize the treatment process. A techno-economic analysis was conducted to quantify chemical and energy savings as well as production of 10-lb brine as a saleable product. With the field-collected BDW and PW samples, mixing experiments determined a volumetric mixing ratio 10:1 (BDW:PW) resulted in the best performance of multivalent ions removal and largest chemical savings for softening. Softening of the BDW/PW mixtures using alkaline chemicals (Na 2 CO 3 and NaOH) achieved 95%-100% removal of scaling-forming cations (Ca, Mg, Fe, Ba, Sr) and 60% of silicon, and 10% of total organic carbon (TOC). The mixing and softening treatments yielded an effluent with total dissolved solids (TDS) concentration of 23 g/L. Activated carbon (AC) filtration removed TOC to a low level (< 3 mg/L) and further removed remaining scale-forming divalent metals and silica from the softened water. The AC filtration resulted in a slight reduction of TDS from 23 g/L to 20 g/L, leaving behind only mostly monovalent ions (i.e., sodium and chloride) in the filtered water. These pretreatments yielded a feed water that met the criteria of the downstream reverse osmosis (RO) to prevent membrane fouling. A cross-flow RO system was used to further concentrate the TDS of the AC effluent. Various factors including TDS, pH, and applied pressure were examined and optimal conditions were determined for the co-treatment process. An integrated process consisting of mixing, softening, AC filtration and RO was used to treat a continuous flow (0.25 – 1.2 L/min, or 0.07 – 0.32 gpm) and successfully generated RO permeate as product water (TDS < 0.5 g/L) for reuse in cooling operation, and a concentrate (TDS ~ 45 g/L) to be further treated in a thermal desalination unit. These flow rates meet the FOA’s criterion of 0.01 – 1 gpm. Overall, the co-treatment of BDW/PW allowed shorter ramp-up time compared to treatment of BDW alone. It resulted in 40% and 55% savings of Na 2 CO 3(s) and NaOH, respectively, compared to treating the BDW and PW individually for the same level of softening. The co-treatment also resulted in a 29% energy saving compared to treatment of BDW only for the level of TDS concentration. A thermal desalination system was designed using CFD simulations and manufactured in the WVU Innovation Hub for further treatment of the RO concentrate to generate 10-lb brine. The system has a design flow rate of 2 gpm and has been successfully tested. A bench-scale brine electrolysis system was developed for on-site generation of chlorine/hypochlorite (Cl 2 /OCl - ) and caustic soda (NaOH) as useful chemicals for the co-treatment process. Using salt solutions (0.5 M and 1 M), the system achieved faradaic efficiencies of 93%-97% and 70%-77% for caustic soda and chlorine/hypochlorite generation, respectively. An economic analysis showed that the electricity costs for on-site generation of these chemicals were significantly lower than the chemical prices offered by suppliers. An industrial-scale process model consisting of mixing, softening, AC filtration, RO, thermal desalination, and brine electrolysis was developed using the Aspen Plus V9 in conjunction with Aspen Custom Modeler V9. The model serves as a solvable Aspen Plus model and as basis to form the costing infrastructure. In addition, techno-economic analysis considering capital, operating, and transportation costs was conducted. An optimization solution showed that produced water for mixing is still advantageous in low quantities. The optimum solution approaches a leveled cost of water (LCW) of 2 $/m 3 which becomes cost competitive with nominal water treatment prices.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2022

Evaluating the Lightning Strike Damage Tolerance for CFRP Composite Laminates Containing Conductive Nanofillers

Conductive nanofillers, such as carbon nanotube, graphene nanoplatelets, and carbon black particles (with diameters in nanometers) have been shown to enhance the electrical conductivity of fiber reinforced polymer matrix composites in many existing studies. The motivation is primarily for lightning strike protection, electromagnetic interference shielding, de-icing, and the manufacturing of lightweight electronic components. Here, we evaluate the lightning strike damage tolerance of carbon fiber reinforced polymer (CFRP) matrix composite laminates containing conductive nanofillers with varying weight fractions, including carbon black (CB), carbon nanotubes (CNT), and a mix of CB and CNT, through simulated lightning strike tests, followed by both non-destructive ultrasonic inspection and destructive sectioning to characterize the damage inflicted by the simulated lightning strike. Three-point flexural tests are performed to evaluate the residual strength retained by all CFRP specimens. Results show that lightning strike damage experienced varying levels of reduction for CFRP composite specimens containing conductive fillers in comparison to the baseline specimen without fillers. Notably, the delamination only penetrated to the interface between the 1st and 2nd layer for the specimen with 0.25 wt.% CNT in comparison to the baseline CFRP specimen for which the delamination penetrated to the interface between the 5th and 6th layer. Moreover, the retention of the flexural modulus increased from 26.5% to a maximum of 95.0% for the specimen with 0.25 wt.% hybrid CB and CNT. Yet, we show that using our chosen conductive fillers cannot fully eliminate lightning strike damage. Additionally, adding conductive fillers could compromise the flexural properties. We provide discussions on future recommendations on using conductive fillers for the lightning strike protection of CFRP composites.

36 MATERIALS SCIENCE↗
DOE OSTI2024

One-Pot Coating of Ceramic Powders by Exfoliated Boron Nitride Layers with a Dense CO 2 Medium and Ultrasound-Aided Mixing

The coating or doping of substrates by two-dimensional materials to impart superior functional properties (such as improved thermal conductivity, bacterial resistance, reduced friction) is receiving increased attention. Environmentally benign, rapid and scalable coating techniques are desirable for this purpose. Here, we report a novel process for coating alumina, silicon carbide and boron carbide substrates with hexagonal boron nitride (h-BN) layers. The process consists of two sequential steps. First, h-BN layers are exfoliated from bulk h-BN in supercritical carbon dioxide (scCO 2 ) using ultrasound-aided mixing. This step is followed by self-assembly (i.e., coating) of the exfoliated h-BN on the substrates in liquid CO 2 also aided by ultrasound. The liquid CO 2 state is achieved by simply lowering the pressure and temperature of the first step below the critical point of CO 2 (P c = 72.8 atm; T c = 31.1 °C). Scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) micrographs clearly reveal the exfoliation of h-BN under scCO 2 conditions as well as the h-BN assembly on various substrates under liquid CO 2 conditions. X-ray diffraction patterns confirm the structural integrity of the coated h-BN layers. It was also confirmed that without a transition to the liquid CO 2 phase following exfoliation in scCO 2 , there was negligible coating of h-BN on the substrates. Researchers in the field could consider this benign process to rapidly coat or dope materials with h-BN and other 2D materials to impart improved functional properties in myriad applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2016

Successful Validation of Sample Processing and Quantitative Real-Time PCR Capabilities on the International Space Station

The WetLab-2 system was developed by NASA Ames Research Center to offer new capabilities to researchers. The system can lyse cells and extract RNA (Ribonucleic Acid) on-orbit from different sample types ranging from microbial cultures to animal tissues. The purified RNA can then either be stabilized for return to Earth or can be used to conduct on-orbit quantitative Reverse Transcriptase PCR (Polymerase Chain Reaction) (qRT-PCR) analysis without the need for sample return. The qRT-PCR results can be downlinked to the ground a few hours after the completion of the run. The validation flight of the WetLab-2 system launched on SpaceX-8 on April 8, 2016. On orbit operations started on April 15th with system setup and was followed by three quantitative PCR runs using an E. coli genomic DNA template pre-loaded at three different concentrations. These runs were designed to discern if quantitative PCR functions correctly in microgravity and if the data is comparable to that from the ground control runs. The flight data showed no significant differences compared to the ground data though there was more variability in the values, this was likely due to the numerous small bubbles observed. The capability of the system to process samples and purify RNA was then validated using frozen samples prepared on the ground. The flight data for both E. coli and mouse liver clearly shows that RNA was successfully purified by our system. The E. coli qRT-PCR run showed successful singleplex, duplex and triplex capability. Data showed high variability in the resulting Cts (Cycle Thresholds [for the PCR]) likely due to bubble formation and insufficient mixing during the procedure run. The mouse liver qRT-PCR run had successful singleplex and duplex reactions and the variability was slightly better as the mixing operation was improved. The ability to purify and stabilize RNA and to conduct qRT-PCR on-orbit is an important step towards utilizing the ISS as a National Laboratory facility. The ability to get on-orbit data will provide investigators with the opportunity to adjust experimental parameters in real time without the need for sample return and re-flight. The WetLab-2 Project is supported by the Research Integration Office in the ISS Program.

gene expression↗
NASA NTRS2016

Successful Validation of Sample Processing and Quantitative Real-Time PCR Capabilities on the International Space Station

The WetLab-2 system was developed by NASA Ames Research Center to offer new capabilities to researchers. The system can lyse cells and extract RNA (Ribonucleic Acid) on-orbit from different sample types ranging from microbial cultures to animal tissues. The purified RNA can then either be stabilized for return to Earth or can be used to conduct on-orbit quantitative Reverse Transcriptase PCR (Polymerase Chain Reaction) (qRT-PCR) analysis without the need for sample return. The qRT-PCR results can be downlinked to the ground a few hours after the completion of the run. The validation flight of the WetLab-2 system launched on SpaceX-8 on April 8, 2016. On orbit operations started on April 15th with system setup and was followed by three quantitative PCR runs using an E. coli genomic DNA template pre-loaded at three different concentrations. These runs were designed to discern if quantitative PCR functions correctly in microgravity and if the data is comparable to that from the ground control runs. The flight data showed no significant differences compared to the ground data though there was more variability in the values, this was likely due to the numerous small bubbles observed. The capability of the system to process samples and purify RNA was then validated using frozen samples prepared on the ground. The flight data for both E. coli and mouse liver clearly shows that RNA was successfully purified by our system. The E. coli qRT-PCR run showed successful singleplex, duplex and triplex capability. Data showed high variability in the resulting Cts (Cycle Thresholds [for the PCR]) likely due to bubble formation and insufficient mixing during the procedure run. The mouse liver qRT-PCR run had successful singleplex and duplex reactions and the variability was slightly better as the mixing operation was improved. The ability to purify and stabilize RNA and to conduct qRT-PCR on-orbit is an important step towards utilizing the ISS as a National Laboratory facility. The ability to get on-orbit data will provide investigators with the opportunity to adjust experimental parameters in real time without the need for sample return and re-flight. The WetLab-2 Project is supported by the Research Integration Office in the ISS Program.

quantitative PCR↗
DOE OSTI2021

Material Design Strategy for Halide Solid Electrolytes Li 3 MX 6 (X = Cl, Br, and I) for All-Solid-State High-Voltage Li-Ion Batteries

Although several solid electrolyte (SE) candidates have been explored, achieving the necessary combination of performance, stability, and processability has been challenging. Recently, several lithium ternary halides have attracted increasing attention for SEs because of their favorable combination of high ionic conductivity and wide electrochemical window. This study aims to provide a material design strategy for lithium halides Li 3 MX 6 (X = Cl, Br, and I) for high-voltage all-solid-state Li-ion batteries, achieved by the systematic investigation of crystal structures, phase and electrochemical stabilities, electronic and mechanical properties, and ionic conductivities. Calculation results reveal that the electronegativity difference between M and X affects structural properties and stabilities. Weak Coulomb interactions in Li 3 MX 6 result in the preference of the monoclinic phase, and the oxidation potential and chemical stability against the cathode materials of Li 3 MX 6 increase for relatively small X. Chlorides exhibit the highest oxidation potential (~4.3 V) among Li 3 MX 6 , suggesting that chlorides are appropriate SEs for high-voltage cathodes. The band gap and elastic moduli increase for relatively small X, suggesting the relatively low electronic conductivity and elastic deformability of chlorides. Chlorides with transition metals typically exhibit trigonal phases, a wider electrochemical stability window, a larger band gap, and higher elastic moduli compared to other types of halides. Additionally, chloride Li 3 MCl 6 is expected to have relatively high ionic conductivities with the aliovalent substitution of M 3+ to Zr 4+ and the anion mixing of Cl with Br. The findings of this study will provide fundamental guidelines for the development of lithium halide SEs for high-voltage all-solid-state Li-ion batteries.

25 ENERGY STORAGE↗
NASA NTRS1985

Interaction of mixed mode loading on cyclic debonding in adhesively bonded composite joints

A combined experimental and analytical investigation of an adhesively-bonded composite joint was conducted to characterize the fracture mode dependence of cyclic debonding. The system studied consisted of graphite/epoxy adherends bonded with EC 3445 adhesive. Several types of specimens are tested which provide the cyclic debond growth rate measurements under various load conditions: mode 1, mixed mode 1 to 2, and mostly mode 2. This study shows that the total strain-energy-release rate is the governing factor for cyclic debonding.

Mall, S.↗
NASA NTRS1985

Interaction of mixed mode loading on cyclic debonding in adhesively bonded composite joints

A combined experimental and analytical investigation of an adhesively-bonded composite joint was conducted to characterize the fracture mode dependence of cyclic debonding. The system studied consisted of graphite/epoxy adherends bonded with EC 3445 adhesive. Several types of specimens are tested which provide the cyclic debond growth rate measurements under various load conditions: mode 1, mixed mode 1 to 2, and mostly mode 2. This study shows that the total strain-energy-release rate is the governing factor for cyclic debonding.

Mall, S.↗
NASA NTRS2003

Enhanced Mixing in a Rectangular Duct

An experimental investigation of the mixing of non-reacting opposed rows of jets injected normal to a confined rectangular crossflow has been conducted. Planar Mie-scattering was used to measure the time-average concentration distribution of the jet fluid in planes perpendicular to the duct axis. Particular emphasis was placed on the study of closely spaced orifice configurations applicable to the mixing zone of an RQL combustor. Baseline studies were performed of mixing under "ideal" conditions, i.e., plenum fed jets injecting into a crossflow uniform in velocity and turbulence intensity. In addition, more practical ("non-ideal") issues encountered during hardware design were also studied. As in other studies, mixing effectiveness, determined using a spatial unmixedness parameter based on the variance of mean jet concentration distributions, was found to be optimum when the spacing-to-duct-height ratio was inversely proportional to the square root of the jet-to-mainstream momentum-flux ratio. This relationship is suitable for design under ideal flow conditions. Inlet flow boundary conditions of the jet and approach flow (mainstream) were found to strongly influence mixing performance, but no attempt was made to determine optimum performance under non-ideal conditions. The tests performed do offer some guidance as to expected mixing behavior for several common variables likely to be imposed by hardware constraints. Additionally, in this study it was found that for rows of orifices with opposite centerlines inline, mixing was similar for blockages up to 89 percent (previous crossflow mixing studies concerned with dilution zone configurations, blockages were typically less than 50 percent). Lower levels of unmixedness were obtained as a function of downstream location when axial injection length was minimized. Mixing may be enhanced if orifice centerlines of opposed rows are staggered, but blockage must be =50 percent in this configuration. Round hole and "square" orifice shapes had similar performance. Other variations in orifice shape did not substantially augment overall mixing performance. Furthermore an isothermal mixing data set was generated and used by CFDRC as input to a NO(x) inference code.

Liscinsky, D. S.↗
NASA NTRS2003

Survival of endospores of Bacillus subtilis on spacecraft surfaces under simulated martian environments: implications for the forward contamination of Mars

Experiments were conducted in a Mars simulation chamber (MSC) to characterize the survival of endospores of Bacillus subtilis under high UV irradiation and simulated martian conditions. The MSC was used to create Mars surface environments in which pressure (8.5 mb), temperature (-80, -40, -10, or +23 degrees C), gas composition (Earth-normal N2/O2 mix, pure N2, pure CO2, or a Mars gas mix), and UV-VIS-NIR fluence rates (200-1200 nm) were maintained within tight limits. The Mars gas mix was composed of CO2 (95.3%), N2 (2.7%), Ar (1.7%), O2 (0.2%), and water vapor (0.03%). Experiments were conducted to measure the effects of pressure, gas composition, and temperature alone or in combination with Mars-normal UV-VIS-NIR light environments. Endospores of B. subtilis, were deposited on aluminum coupons as monolayers in which the average density applied to coupons was 2.47 x 10(6) bacteria per sample. Populations of B. subtilis placed on aluminum coupons and subjected to an Earth-normal temperature (23 degrees C), pressure (1013 mb), and gas mix (normal N2/O2 ratio) but illuminated with a Mars-normal UV-VIS-NIR spectrum were reduced by over 99.9% after 30 sec exposure to Mars-normal UV fluence rates. However, it required at least 15 min of Mars-normal UV exposure to reduce bacterial populations on aluminum coupons to non-recoverable levels. These results were duplicated when bacteria were exposed to Mars-normal environments of temperature (-10 degrees C), pressure (8.5 mb), gas composition (pure CO2), and UV fluence rates. In other experiments, results indicated that the gas composition of the atmosphere and the temperature of the bacterial monolayers at the time of Mars UV exposure had no effects on the survival of bacterial endospores. But Mars-normal pressures (8.5 mb) were found to reduce survival by approximately 20-35% compared to Earth-normal pressures (1013 mb). The primary implications of these results are (a) that greater than 99.9% of bacterial populations on sun-exposed surfaces of spacecraft are likely to be inactivated within a few tens of seconds to a few minutes on the surface of Mars, and (b) that within a single Mars day under clear-sky conditions bacterial populations on sun-exposed surfaces of spacecraft will be sterilized. Furthermore, these results suggest that the high UV fluence rates on the martian surface can be an important resource in minimizing the forward contamination of Mars. c2003 Elsevier Inc. All rights reserved.

Bacillus subtilis/growth & development/physiology/↗
DOE OSTI2022

Three-dimensional microstructural characterization of FBR MOX fuel and the contribution of microstructural features to the thermal conductivity of the fuel

Combination of microstructural characterization, property measurements, and phase field modeling is used to investigate fast breeder reactor (FBR) mixed oxide (MOX) fuel irradiated to burnup of 13.7% fissions per initial metal atom (FIMA). Here, the fuel was characterized at different radial locations, which revealed that grey phase can be present in the central region if it nucleates on five metal precipitates (FMPs). In addition, in the mid-radial region FMPs do not diffuse out of the region once formed and the size of Pd–Te precipitates is dictated by the porosity present in the region. Thermal conductivity measurements were conducted as a function of radial location and the microstructure of the fuel was correlated with the observed trend. Reconstructions of the 3D solid and gaseous fission product structures in different regions of the fuel were used to simulate the effective thermal conductivity (ETC) of the respective regions and determine which microstructural feature has the strongest impact on thermal conductivity. Based on conducted assessment, FMPs and Pd-Te precipitates improve local conductivity of central and mid-radial regions even in the presence of grey phase, but defects are primary contributor to the degradation of thermal conductivity on the periphery of the fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

The effect of barrier films and exposure on the aging of vacuum insulation panels with fumed silica cores

Vacuum insulation panels have very low thermal conductivities compared to conventional insulation materials. The reduction of the core pressure significantly lowers gas phase conduction and overall thermal conductivity. As a consequence, increases in gas pressure can significantly increase thermal conductivity of the VIP. In addition, the thermal conductivity of the core is sensitive to moisture content. For vacuum insulation panels with fumed silica cores, work shows that the measured thermal conductivity increases by 0.5 x 10-3 W/mK per mass percent increase in water content [1]. This is significant since the thermal conductivity of vacuum insulation panels with fumed silica cores is in the range of 0.004 W/mK. This work investigates the long-term behavior of vacuum insulation panels comprised of fumed silica cores with polymer (ethylene vinyl alcohol) and metalized (aluminized) barrier films exposed to different exposure conditions: ambient conditions; exterior conditions in a mixed humid climate; and 24oC and 80 percent relative humidity. Results show that the increase in thermal conductivity is more pronounced for vacuum insulation panels made using polymer barrier films compared to the same panel protected by a metalized film. The increase is more pronounced when exposed to high relative humidity, 80 percent. After almost two years exposure, the decrease in thermal conductivity for vacuum insulation panels protected by a metalized barrier films are between 4 and 11 percent depending on exposure condition. The smallest decrease is for ambient conditions where the largest decrease is for exposure to 80 percent relative humidity. Similar behavior was observed for panels protected using polymer films, except the decrease in thermal conductivity was significantly higher, between approximately 20 and 60 percent, in the same order as for panels protected by metalized films. Measurements are ongoing with an attempt to develop a better relationship between these types of tests and vacuum insulation panel service life.

Aldykiewicz Jr, Antonio↗
DOE OSTI2024

Self-reported health impacts of do-it-yourself air cleaner use in a smoke-impacted community

Smoke exposure from wildfires or residential wood burning for heat is a public health problem for many communities. Do-It-Yourself (DIY) portable air cleaners (PACs) are promoted as affordable alternatives to commercial PACs, but evidence of their effect on health outcomes is limited. Pilot test an evaluation of the effect of DIY PAC usage on self-reported symptoms, and investigate barriers and facilitators of PAC use, among members of a tribal community that routinely experiences elevated concentrations of fine particulate matter (PM 2.5 ) from smoke. We conducted studies in Fall 2021 (“wildfire study”; N = 10) and Winter 2022 (“wood stove study”; N = 17). Each study included four sequential one-to-two-week phases: 1) initial, 2) DIY PAC usage ≥8 h/day, 3) commercial PAC usage ≥8 h/day, and 4) air sensor with visual display and optional PAC use. We continuously monitored PAC usage and indoor/outdoor PM 2.5 concentrations in homes. Concluding each phase, we conducted phone surveys about participants’ symptoms, perceptions, and behaviors. We analyzed symptoms associated with PAC usage and conducted an analysis of indoor PM 2.5 concentrations as a mediating pathway using mixed effects multivariate linear regression. We categorized perceptions related to PACs into barriers and facilitators of use. No association was observed between PAC usage and symptoms, and the mediation analysis did not indicate that small observed trends were attributable to changes in indoor PM 2.5 concentrations. Small sample sizes hindered the ability to draw conclusions regarding the presence or absence of causal associations. DIY PAC usage was low; loud operating noise was a barrier to use. This research is novel in studying health effects of DIY PACs during wildfire and wood smoke exposures. Such research is needed to inform public health guidance. Recommendations for future studies on PAC use during smoke exposure include building flexibility of intervention timing into the study design.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Evaluating High-Halide Waste Form Options for Salt-Based Nuclear Waste Simulants

In this study, waste forms were being explored for an electrochemical salt simulant, , referred to as ERV3, which is a high-LiCl/KCl salt containing simulated fission products (i.e., Sr, Cs, Nd) and Na to represent bond sodium from Experimental Breeder Reactor-II metallic fast reactor fuel. The goal was to find glassy systems that could be used to immobilize the salt in a single-step process. The envisionment of this process would be find a frit glass that could be added to the salt waste, heat treated, poured into waste canisters, and then stored for disposal. To perform this study, a literature review was conducted, the most promising seven systems were fabricated without the salt, and then mixed with salt simulant and heat treated under different processes. The criteria that were used to screen potential compositions included demonstrated alkali incorporation, could be melted at reasonably low temperature ( T ≤ 1000°C), and if the compositions had some demonstrated data for waste-form-related properties, that was a benefit. High marks were given for compositions that showed amorphous nature after slow cooling of samples containing ERV3.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Fine Aerosol Acidity and Water during Summer in the Eastern North Atlantic

Aerosol pH governs many important atmospheric processes that occur in the marine boundary layer, including regulating halogen and sulfur chemistries, and nutrient fertilization of surface ocean waters. In this study, we investigated the acidity of PM1 over the eastern North Atlantic during the Aerosol and Cloud Experiments in Eastern North Atlantic (ACE-ENA) aircraft campaign. The ISORROPIA-II thermodynamic model was used to predict PM1 pH and water. We first investigated the sensitivities of PM1 pH and water predictions to gas-phase NH3 and HNO3 concentrations. Our sensitivity analysis indicated that even though NH3 and HNO3 were present at very low concentrations in the eastern North Atlantic during the campaign, PM1 pH calculations can still be sensitive to NH3 concentrations. Specifically, NH3 was needed to constrain the pH of populations of PM1 that had low mass concentrations of NH4+ and non-volatile cations (NVCs). We next assumed that gas-phase NH3 and HNO3 concentrations during the campaign were 0.15 and 0.09 µg m−3, respectively, based on previous measurements conducted in the eastern North Atlantic. Using the assumption that PM1 were internally mixed (i.e., bulk PM1), we determined that PM1 pH ranged from 0.3–8.6, with a mean pH of 5.0 ± 2.3. The pH depended on both Hair+ and Wi. Hair+ was controlled primarily by the NVCs/SO42− molar ratio, while Wi was controlled by the SO42− mass concentration and RH. Changes in pH with altitude were driven primarily by changes in SO42−. Since aerosols in marine atmospheres are rarely internally mixed, the scenario where non-sea salt species and sea-salt species were present in two separate aerosol modes in the PM1 (i.e., completely externally mixed) was also considered. Smaller pH values were predicted for the aerosol mode comprised only of non-sea salt species compared to the bulk PM1 (difference of around 1 unit on average). This was due to the exclusion of sea-salt species (especially hygroscopic alkaline NVCs) in this aerosol mode, which led to increases in Hair+ values and decreases in Wi values. This result demonstrated that assumptions of aerosol mixing states can impact aerosol pH predictions substantially, which will have important implications for evaluating the nature and magnitude of pH-dependent atmospheric processes that occur in the marine boundary layer.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1973

Minimizing boundary layer bleed for a mixed compression inlet

An experimental investigation of a full scale mixed compression inlet sized for the TF30-P-3 turbofan engine was conducted at Mach 2.5 and 2.0 operating conditions. The two cone axisymmetric inlet had minimum internal contraction consistent with high total pressure recovery and low cowl drag. At Mach 2.5, inlet recovery exceeded 0.90 with only 0.02 centerbody bleed mass-flow ratio and zero cowl bleed. A centerbody bleed of approximately 0.05 gave a maximum inlet unstart angle-of-attack of 6.85 deg. Inlet performance and angle-of-attack tolerance is presented for operation at Mach 2.5 and 2.0.

Wasserbauer, J. F.↗