Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “met”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Verification of the SRB motor case pin retainer band tips

The pin retainer band is a 1-1/4 in. wide by about 1/32 in. thick steel band that is stretched over the pins circumferentially at the joints of the solid rocket booster (SRB) motor case segments. Its purpose is to hold the retaining pins in place during flight. Since the band is thin and is mounted stretched, or under tension, over the pins which are greased in place, it is necessary to protect it thermally. Three typical areas of the band location on the SRB motor case joints were chosen for verifying the cork thermal prection system (TPS) performance on the band: the joint in front of the attach ring, at the aft skirt joint in front of the kick ring and in an unperturbed area at the forward segments of the SRB motor cases. The kick ring area pin retainer band cork TPS passed the test requirements in the region where there are no phenolic splice caps. In the splice cap areas where the band TPS is closed out around the splice with K5NA, additional amounts of K5NA material is required to adequately protect the steel band. TPS requirements were easily met in the one location where the ends of the steel band are joined together after installation and tensioning. The attack ring area pin retainer band TPS did not quite pass the heat load requirements with the .375 in. thick cork TPS as used for the kick ring area band. It is recommended that the cork thickness here be increased to .50 in. The unperturbed area band TPS presented no problems.

Karu, Z. S.↗
NASA NTRS1983

Galilean satellite remote sensing by the Galileo Jupiter Orbiter

The derivation of a mission design strategy for the Galileo Jupiter Orbiter which best satisfies the requirements for remote sensing of the surfaces of the Galilean satellites during a 20-month orbital tour of the Jovian system is described. The celestial mechanics of a spacecraft orbiting about Jupiter and interacting with the Galilean satellites is discussed. A satellite tour strategy designed to optimize the accomplishment of remote sensing, field and particle science, and radio science objectives is developed. Finally, an assessment is made of how well these objectives can be met given the spacecraft, the capabilities of the scientific instruments, and the structure of the satellite tour.

Yeates, C. M.↗
NASA NTRS1985

The Mars Observer Mission

The Mars Observer Mission is to be the first in a series of modest-cost inner-planet missions. Launch is planned for the August/September 1990 Mars opportunity with arrival at Mars one year later. The geoscience/climatology objectives are to be met during a mapping mission over the course of one Mars year (687 days). The mapping orbit will be near-polar (93 degree orbital inclination), sun-synchronous (2 PM sunward equator crossing), and near-circular (350 km orbit altitude, 116 minute period). The spacecraft, to be selected in late 1985, will be a modified version of an existing commercial design which, in the mapping orbit, will maintain a nadir orientation. Experiments and instruments will be selected through an Announcement of Opportunity (AO) process with release of the AO in April 1985, and selection in early 1986. A description of current planning for this mission, with emphasis on climatology, is presented here.

Palluconi, F. D.↗
NASA NTRS1985

Study of navigation accuracy for the proposed QUASAT mission

A covariance analysis has been performed for the proposed QUASAT, an earth orbiting radio telescope. Conventional (Doppler and range) and advanced (diifferenced and doubly differenced one-way range) radio metric data types are used to evaluate the navigation accuracy that can be achieved. It is found that the mission requirements are met by conventional data types, while advanced data types can provide an order of magnitude improvement with less measurements, provided the three NASA DSN stations are augmented by more closely spaced stations.

Jacobi, N.↗
NASA NTRS1985

Expanding role for autonomy in military space

The Jet Propulsion Laboratory is currently transferring satellite on-board autonomy technology to the USAF for use in military spacecraft as a means of lowering the ground support requirements. The techniques were proven on the Viking and Voyager spacecraft and permitted on-board fault detection and correction. New military satellites will incorporate an autonomous redundancy and maintenance management subsystem in an on-board computer, while the system will still be subject to ground-based safing commands for situations demanding deeper analyses. A level 5 autonomy will need 256 kb memory, 10 Mb nonvolatile data storage and 50 W power and will weigh 20 kg. Systems will be periodically checked and compared with an ideal in the data base. Deviations detected will result in a rollback and redundant examination by two microprocessors, which can initiate correction commands until operational criteria are met. The development of the expert systems to the point that they satisfy military specifications is expected to take 10 yr.

Evans, D. D.↗
NASA NTRS1984

Steps toward 8m honeycomb mirrors IV - Some aspects of design and fabrication

The tolerances in glass homogeneity, thermal control, and support of the blank, necessary to meet the requirements of telescopes in the best ground-based sites, are defined for a hypothetical 8-m honeycomb mirror spin-casting facility. Homogeneity in expansion coefficient of 10 to the -8th/C and thermal equilibration to 0.1 C are estimated. Laboratory measurements show that both can be met by a ventilated honeycomb of borosilicate or similar glass. Adequate resistance to wind pressure and buffeting can be achieved by an axial support that responds to pressure on the three defining points. Annealing of the blank at the peak cooling rate of 20 C/day will take about six weeks, leading to a temporary stress of 15 kg/sq cm.

Angel, J. R. P.↗
NASA NTRS1983

Capture and real-time display of selected Space Shuttle reentry data

Because the flight planning for the orbital flight test (OFT) flights of the NASA Space Shuttle required several months, there was very little time to analyze data from one flight before it was necessary to start final planning for the next flight. Real-time and selected immediate postflight data display of the reentry data minimized the postflight computer analysis time required so that the rigid time restraints imposed by the program could be met. This paper describes the methods used to decommutate and provide real-time and immediate postflight data display of selected Space Shuttle reentry data.

Chiles, H. R.↗
NASA NTRS1984

Space-constructible heat pipe radiator thermal vacuum test program

The thermal vacuum test program being carried out at the Johnson Space Center on two prototype radiator elements intended for use in future large space platforms is discussed. The test program is described, as are the test articles, including the radiator element, evaporator assemblies, mechanical interface unit, contact heat exchanger assembly, tilt table mechanism, and supports. Test results on the heat pipe performance, radiator element performance, freeze/thaw characteristics, and contact heat exchanger assembly mechanism are discussed. It is concluded that the fundamental design goals for the radiator subsystem have been met.

Marshall, P. F.↗
NASA NTRS1985

Heat transport across structural boundaries

A description of a program which uses heat-pipe principles in the design of prototype rotating thermal joints for the NASA centralized thermal control system, as well as of the first six months of work, during which the contract goals were met, is given. The design requirements include operating in a temperature range from 0 to 40 C, transferring 10 kilowatts with an overall temperature drop of 5 C, and rotating a total of 60,000 revolutions at 2 rpm with a 1700 inch pound moment loading. The predicted and required performance for the rotating joint are compared and the results are presented in a table. Consideration is also given to Phase II of the program.

Shaubach, R. M.↗
NASA NTRS1985

High performance flexible heat pipes

A Phase I SBIR NASA program for developing and demonstrating high-performance flexible heat pipes for use in the thermal management of spacecraft is examined. The program combines several technologies such as flexible screen arteries and high-performance circumferential distribution wicks within an envelope which is flexible in the adiabatic heat transport zone. The first six months of work during which the Phase I contract goal were met, are described. Consideration is given to the heat-pipe performance requirements. A preliminary evaluation shows that the power requirement for Phase II of the program is 30.5 kilowatt meters at an operating temperature from 0 to 100 C.

Shaubach, R. M.↗
NASA NTRS1985

Photovoltaic performance models - A report card

Models for the analysis of photovoltaic (PV) systems' designs, implementation policies, and economic performance, have proliferated while keeping pace with rapid changes in basic PV technology and extensive empirical data compiled for such systems' performance. Attention is presently given to the results of a comparative assessment of ten well documented and widely used models, which range in complexity from first-order approximations of PV system performance to in-depth, circuit-level characterizations. The comparisons were made on the basis of the performance of their subsystem, as well as system, elements. The models fall into three categories in light of their degree of aggregation into subsystems: (1) simplified models for first-order calculation of system performance, with easily met input requirements but limited capability to address more than a small variety of design considerations; (2) models simulating PV systems in greater detail, encompassing types primarily intended for either concentrator-incorporating or flat plate collector PV systems; and (3) models not specifically designed for PV system performance modeling, but applicable to aspects of electrical system design. Models ignoring subsystem failure or degradation are noted to exclude operating and maintenance characteristics as well.

Smith, J. H.↗
NASA NTRS1985

Manned flight simulation: Challenge and response

Early AGARD papers on manned flight simulation describe the status of an emerging test technique and then offer suggestions of problems that should be solved to advance the technique and predictions of the results that will be obtained by its use. Later AGARD literature is examined to determine how these challenges have been met, both in ground-based and in-flight simulation and how AGARD has played an important role in advancing the technique so that it is now an integral part of the aerospace vehicle design process.

Dusterberry, J. C.↗
NASA NTRS1985

Explosive Welding of Tubular Configurated Joints for Critical Applications

Explosive welding can provide the answer to problems of permanently joining metals typically used in the aerospace industry. The explosive bonding process is a solid state bonding process enabling material incompatibility problems associated with fusion welding to be overcome. In addition, heat affected zones are eliminated thus, enhancing joint strength, properties and performance. The process requires the parts being joined to be impelled, by means of explosives, to collide with each other. Certain critical collision parameters must be met and controlled and these parameters are defined. Various component geometries which satisfy the collision parameters are described. Examples of transition joints used in the aerospace industry are described and illustrated.

Hardwick, R.↗
NASA NTRS1985

Design of a flight qualified long-life cryocooler

A second generation Stirling cycle cryogenic refrigerator with a linear drive, magnetic bearings, and clearance seals; designed to produce 5 watts of cooling at 65 Kelvin and to meet Space Shuttle mission requirements is described. The first generation refrigerator met all performance specifications, and operated with no failure for over 12,030 hours. Meeting launch requirements necessitated improvements in the electromagnetic bearings, the radial position sensors, and in the structural design of the moving elements. Organic contamination was eliminated by the use of all metal and ceramic construction. Reductions in system input power are attained by an integral magnetic spring/motor for the displacer and by more efficient linear motors and drive electronics.

Knox, L.↗
NASA NTRS1983

Coolant passage heat transfer with rotation. A progress report on the computational aspects

Turbine airfoils are subjected to increasingly higher heat loads which escalate the cooling requirements in order to satisfy life goals for the component materials. If turbine efficiency is to be maintained, however, cooling requirements should be as low as possible. To keep the quantity of cooling air bounded, a more efficient internal cooling scheme must be developed. One approach is to employ airfoils with multipass cooling passages that contain devices to augment internal heat transfer while limiting pressure drop. Design experience with multipass cooling passage airfoils has shown that a surplus of cooling air must be provided as a margin of safety. This increased cooling air leads to a performance penalty. Reliable methods for predicting the internal thermal and aerodynamic performance of multipass cooling passage airfoils would reduce or eliminate the need for the safety margin of surplus cooling air. The objective of the program is to develop and verify improved analytical methods that will form the basis for design technology which will result in efficient turbine components with improved durability without sacrificing performance. The objective will be met by: (1) establishing a comprehensive experimental data base that can form the basis of an empirical design system; (2) developing computational fluid dynamic techniques; and (3) analyzing the information in the data base with both phenomenological modeling and mathematical modeling to derive a suitable design and analysis procedure.

Aceto, L. D.↗
NASA NTRS1985

Estimation of finite mixtures using the empirical characteristic function

A problem which occurs in analyzing LANDSAT scenes is the problem of separating the components of a finite mixture of several distinct probability distributions. A review of the literature indicates this is a problem which occurs in many disciplines, such as engineering, biology, physiology and economics. Many approaches to this problem have appeared in the literature; however, most are very restrictive in their assumptions or have met with only a limited degree of success when applied to realistic situations. A proceudre is investigated with combines the k-L procedure of (Feurverger and McDunnough, 1981) with the MAICE procedure of (Akaike, 1974). The feasibility of this approach is being investigated numerically via the development of a computer software package enabling a simulation study and comparison with other procedures.

Anderson, C.↗
NASA NTRS1985

Pressure distributions from high Reynolds number tests of a Boeing BAC 1 airfoil in the Langley 0.3-meter transonic cryogenic tunnel

A wind-tunnel investigation designed to test a Boeing advanced-technology airfoil from low to flight-equivalent Reynolds numbers has been completed in the Langley 0.3-Meter Transonic Cryogenic Tunnel. This investigation represents the first in a series of NASA/U.S. industry two-dimensional airfoil studies to be completed in the Advanced Technology Airfoil Test program. Test temperature was varied from ambient to about 100 K at pressures ranging from about 1.2 to 6.0 atm. Mach number was varied from about 0.40 to 0.80. These variables provided a Reynolds number (based on airfoil chord) range from 4.4 X 10 to the 6th power to 50.0 X 10 to the 6th power. All the test objectives were met. The pressure data are presented without analysis in plotted and tabulated formats for use in conjunction with the aerodynamic coefficient data published as NASA TM-81922. At the time of the test, these pressure data were considered proprietary and have only recently been made available by Boeing for general release. Data are included which demonstrate the effects of fixed transition. Also included are remarks on the model design, the model structural integrity, and the overall test experience.

Johnson, W. G., Jr.↗
NASA NTRS1985

High dynamic GPS receiver validation demonstration

The Validation Demonstration establishes that the high dynamic Global Positioning System (GPS) receiver concept developed at JPL meets the dynamic tracking requirements for range instrumentation of missiles and drones. It was demonstrated that the receiver can track the pseudorange and pseudorange rate of vehicles with acceleration in excess of 100 g and jerk in excess of 100 g/s, dynamics ten times more severe than specified for conventional High Dynamic GPS receivers. These results and analytic extensions to a complete system configuration establish that all range instrumentation requirements can be met. The receiver can be implemented in the 100 cu in volume required by all missiles and drones, and is ideally suited for transdigitizer or translator applications.

Hurd, W. J.↗