SEARCH · Engineering Papers

Results for “local stresses”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

All sources NASA NTRS DOE OSTI

NASA NTRS2003

Exploratory Calibration of Adjustable-Protrusion Surface-Obstacle (APSO) Skin Friction Vector Gage

The design of an adjustable-protrusion surface-obstacle (APSO) skin friction vector gage is presented. Results from exploratory calibrations conducted in laminar and turbulent boundary layers at the Washington University Low-Speed Wind Tunnel and for turbulent boundary layers at speeds up to Mach 2 on the ceiling of the NASA Glenn Research Center 8- X 6-ft Supersonic Wind Tunnel are also discussed. The adjustable-height gage was designed to yield both the magnitude and direction of the surface shear stress vector and to measure the local static pressure distribution. Results from the NASA test show good correlation for subsonic and low supersonic conditions covering several orders of magnitude in terms of the adopted similarity variables. Recommendations for future work in this area consist of identifying the physical parameters responsible for the disagreement between the university and NASA data sets, developing a compressibility correction specific to the APSO geometry, and examining the effect that static pressure distribution and skewed boundary layers have on the results from the APSO.

Hakkinen, Raimo J.↗

NASA NTRS2005

Long-duration Operation of 2-micron Coherent Doppler Lidar in Space

The reliability and lifetime of laser remote sensing systems that can operate autonomously over a sufficiently long period are mainly constrained by the laser diode arrays (LDAs) used for pumping their laser transmitters. The lifetime of a 2-micron coherent lidar operating in space is particularly of concern in lieu of required pump pulse duration of Thulium and Holmium solid state lasers (approx. 1msec) that are considerably longer than those of more widely used 1-micron lasers (< 0.2 msec). A factor of 5 to 10 times longer pulse duration can easily translate to over an order of magnitude shorter lifetime for a typical commercially available high-power 2-D array. Therefore, it is imperative to address the lifetime and reliability of LDAs for pumping 2-micron lasers by exploring all the potential options that significantly prolong their life meeting the required operational lifetime of space-based coherent Doppler lidars. The leading causes of sudden failure and premature degradation of LDAs are intrinsic semiconductor defects, optical facet breakdown resulting from excessive localized heating, and thermo-mechanical stresses due to the extreme thermal cycling of the laser active regions1-2. Long pulse operation grossly amplifies the impact of these failure/degradation causes, particularly the thermo-mechanical stresses due to pulse-to-pulse thermal cycling. Therefore, several experimental setups have been developed to investigate each of the failure mechanisms and causes of premature degradation in order to evaluate various package designs, define the best operating parameters, and to guide the technology advancement, leading to highly reliable and very long lifetime LDAs5. Several areas of improvement in the packaging and fabrication process of laser diodes have already been identified and efforts towards implementing these improvements are well underway. These efforts include the use of advanced high thermal conductivity materials for packaging of laser diode arrays and new fabrication techniques for mechanically attaching laser diode bars and submounts. But even using the existing LDAs, it may be possible to increase the lifetime by careful selection of the package type, number of bars per package and their pitch, operational temperature, and operating parameters such repetition rate, pulsewidth, and applied current. Obviously, the LDA specification and operational parameters will involve a system level trade analysis to ensure that the lidar instrument meets its performance objectives. One goal of this work is to enable such trade analysis by evaluating LDAs from different suppliers in different package types and quantifying their performance as a function of their operational parameters.

Amzajerdian, Farzin↗

NASA NTRSDate not supplied

Developing New Tools for Modeling Rocket Plume-Surface Interactions

With NASA’s goal to land the next human on the lunar surface in the next few years, it has become vitally important that we have a better understanding of how future landing spacecraft will interact with the unique properties of regolith¬¬––the layer of loose, unconsolidated dust and rock on the lunar surface¬¬––which can cause hazards like visual obstructions, particulate clouds, and cratering of the landing zone. Researchers from the Fluid Dynamics Branch at NASA’s Marshall Space Flight Center are performing plume-surface interaction (PSI) simulations between lander engine plumes and unprepared regolith surfaces, and have developed new tools to provide predictive PSI environments for various NASA projects and missions, including the Human Lander System (HLS), Commercial Lunar Payload Services (CLPS), and future Mars landers. These tools allow the researchers to determine how to best meet the simulation and time requirements for each project by varying model fidelity. The highest fidelity tool is the Gas Granular Flow Solver (Loci/GGFS) that models gas-particle multi-phase interactions to predict regolith cratering and ejection of particles into the immediate surroundings of the lander. At its highest fidelity, it can model microscopic regolith particle interactions with a particle size/shape distribution that statistically replicates actual regolith, however, to be most effective with today’s computing resources, it is currently run using only one to three equivalent particle sizes/shapes. The team also incorporated engineering models into their software suite to create production-ready hybrid tools with reduced fidelity. At the lowest fidelity, the computational fluid dynamics (CFD) code Loci/CHEM+DIGGEM can predict crater depth over time by relating local CFD-predicted surface shear stresses to a model of erosion mass flux.

plume surface interaction↗

DOE OSTI2021

Preventing stent failure using adaptive shear responsive endovascular implant

A stent apparatus, system, and method that senses wall shear stress by measuring fluid flow at localized areas within the stent, that processes measured information through an integrated circuit, and selectively sends power to mechanically controllable stent surfaces which results in localized geometric changes. In various embodiments the stent apparatus, system, and method sends data to outside the body in real time.

Mukerjee, Erik V.↗

DOE OSTI2024

Preventing stent failure using adaptive shear responsive endovascular implant

Mukerjee, Erik V.↗

DOE OSTI2024

Thermal, water, and land cover factors led to contrasting urban and rural vegetation resilience to extreme hot months

Abstract With continuing global warming and urbanization, it is increasingly important to understand the resilience of urban vegetation to extreme high temperatures, but few studies have examined urban vegetation at large scale or both concurrent and delayed responses. In this study, we performed an urban–rural comparison using the Enhanced Vegetation Index and months that exceed the historical 90th percentile in mean temperature (referred to as “hot months”) across 85 major cities in the contiguous United States. We found that hot months initially enhanced vegetation greenness but could cause a decline afterwards, especially for persistent (≥4 months) and intense (≥+2 °C) episodes in summer. The urban responses were more positive than rural in the western United States or in winter, but more negative during spring–autumn in the eastern United States. The east–west difference can be attributed to the higher optimal growth temperatures and lower water stress levels of the western urban vegetation than the rural. The urban responses also had smaller magnitudes than the rural responses, especially in deciduous forest biomes, and least in evergreen forest biomes. Within each biome, analysis at 1 km pixel level showed that impervious fraction and vegetation cover, local urban heat island intensity, and water stress were the key drivers of urban–rural differences. These findings advance our understanding of how prolonged exposure to warm extremes, particularly within urban environments, affects vegetation greenness and vitality. Urban planners and ecosystem managers should prioritize the long and intense events and the key drivers in fostering urban vegetation resilience to heat waves.

54 ENVIRONMENTAL SCIENCES↗

NASA NTRS2000

Dissociation between neural and vascular responses to sympathetic stimulation : contribution of local adrenergic receptor function

Sympathetic activation produced by various stimuli, eg, mental stress or handgrip, evokes regional vascular responses that are often nonhomogeneous. This phenomenon is believed to be the consequence of the recruitment of differential central neural pathways or of a sympathetically mediated vasodilation. The purpose of this study was to determine whether a similar heterogeneous response occurs with cold pressor stimulation and to test the hypothesis that local differences in adrenergic receptor function could be in part responsible for this diversity. In 8 healthy subjects, local norepinephrine spillover and blood flow were measured in arms and legs at baseline and during sympathetic stimulation induced by baroreflex mechanisms (nitroprusside infusion) or cold pressor stimulation. At baseline, legs had higher vascular resistance (27+/-5 versus 17+/-2 U, P=0.05) despite lower norepinephrine spillover (0.28+/-0.04 versus 0.4+/-0.05 mg. min(-1). dL(-1), P=0.03). Norepinephrine spillover increased similarly in both arms and legs during nitroprusside infusion and cold pressor stimulation. On the other hand, during cold stimulation, vascular resistance increased in arms but not in legs (20+/-9% versus -7+/-4%, P=0.03). Increasing doses of isoproterenol and phenylephrine were infused intra-arterially in arms and legs to estimate beta-mediated vasodilation and alpha-induced vasoconstriction, respectively. beta-Mediated vasodilation was significantly lower in legs compared with arms. Thus, we report a dissociation between norepinephrine spillover and vascular responses to cold stress in lower limbs characterized by a paradoxical decrease in local resistance despite increases in sympathetic activity. The differences observed in adrenergic receptor responses cannot explain this phenomenon.

NASA Discipline Regulatory Physiology↗

DOE OSTI2020

Residual lattice strain in quartzites as a potential palaeo-piezometer

SUMMARY If a crystal lattice is subjected to a stress, it becomes distorted and no longer represents the ideal crystal symmetry, and if the stress introduces defects such as dislocations, some of this distortion is preserved after the applied stress is removed. In this study, we investigate lattice distortion in quartz at the micron scale with synchrotron X-ray Laue diffraction. From Laue images the local deviatoric strain tensor is derived and corresponding stresses are calculated based on elastic properties. The method is applied to metasedimentary quartzites from the Bergell Alps that were deformed at conditions of greenschist facies metamorphism. The residual palaeostrain is represented in maps of the deviatoric strain tensor components and with deviatoric strain axis pole figures. Data suggest overall shortening perpendicular to the schistosity plane but with considerable asymmetry relative to foliation and lineation, probably attributed to simple shear. Crystallographic pole figures from Laue diffraction agree with neutron diffraction and EBSD measurements and display quartz c-axes girdle distributions with maxima also perpendicular to schistosity. The method shows promise to be used as a palaeo-piezometer to unravel the stress field during tectonic deformation.

58 GEOSCIENCES↗

NASA NTRS1989

Thermoplastic matrix composites - Finite-element analysis of mode I and mode II failure specimens

A finite-element analysis was conducted to evaluate the stress distributions within mode I and mode II failure specimens, assuming both isotropic and orthotropic elastic material properties. The effects of anisotropy on both the magnitude and the location of the highest stress concentration at the vicinity of the crack tip are significant. The results from modeling realistic blunt crack tip geometry and resin-rich zones imply that local variations in the microstructure strongly influence the stress state near the crack tip and therefore the measured fracture properties. In addition, the features of a viscoelastic model for thermoplastic matrices are described. This model will be used in future investigations of matrix-dominated failure phenomena.

Bankert, Ray J.↗

DOE OSTI2023

Thermal Conductivity of AM Fabricated Stainless Steel 316L Part

Thermal properties are an integral part of many diverse engineering applications, and additive manufacturing (AM), particularly laser powder bed fusion (LPBF) is shown to affect thermal properties due to the laser processing parameters. For 316L stainless steel, there is little prior research to determine the effects of the process on thermal properties. In this work, the temperature gradient is shown to create uniform, chess board-like distributions of grains in the build direction. These zones create dislocations which were visualized with EBSD techniques. Processing parameters cause hierarchal grain size distribution, with localized concentrations of small grains and large grains. Thermomechanical stresses in the rapid solidification increases dislocation density during grain formation. Previous research shows a higher density of dislocations decreases local thermal conductivity. Local and bulk thermal conductivity are shown in this work to have statistically lowered values to an average of 10-12 W/m-K compared to 14 W/m-K for conventional 316L.

36 MATERIALS SCIENCE↗

NASA NTRS1999

Design and Development of a Composite Dome for Experimental Characterization of Material Permeability

This paper presents the design and development of a carbon fiber reinforced plastic dome, including a description of the dome fabrication, method for sealing penetrations in the dome, and a summary of the planned test series. This dome will be used for the experimental permeability characterization and leakage validation of composite vessels pressurized using liquid hydrogen and liquid nitrogen at the Cryostat Test Facility at the NASA Marshall Space Flight Center (MSFC). The preliminary design of the dome was completed using membrane shell analysis. Due to the configuration of the test setup, the dome will experience some flexural stresses and stress concentrations in addition to membrane stresses. Also, a potential buckling condition exists for the dome due to external pressure during the leak testing of the cryostat facility lines. Thus, a finite element analysis was conducted to assess the overall strength and stability of the dome for each required test condition. Based on these results, additional plies of composite reinforcement material were applied to local regions on the dome to alleviate stress concentrations and limit deflections. The dome design includes a circular opening in the center for the installation of a polar boss, which introduces a geometric discontinuity that causes high stresses in the region near the hole. To attenuate these high stresses, a reinforcement system was designed using analytical and finite element analyses. The development of a low leakage polar boss system is also investigated.

Estrada, Hector↗

NASA NTRS2003

Intracellular stress tomography reveals stress focusing and structural anisotropy in cytoskeleton of living cells

We describe a novel synchronous detection approach to map the transmission of mechanical stresses within the cytoplasm of an adherent cell. Using fluorescent protein-labeled mitochondria or cytoskeletal components as fiducial markers, we measured displacements and computed stresses in the cytoskeleton of a living cell plated on extracellular matrix molecules that arise in response to a small, external localized oscillatory load applied to transmembrane receptors on the apical cell surface. Induced synchronous displacements, stresses, and phase lags were found to be concentrated at sites quite remote from the localized load and were modulated by the preexisting tensile stress (prestress) in the cytoskeleton. Stresses applied at the apical surface also resulted in displacements of focal adhesion sites at the cell base. Cytoskeletal anisotropy was revealed by differential phase lags in X vs. Y directions. Displacements and stresses in the cytoskeleton of a cell plated on poly-L-lysine decayed quickly and were not concentrated at remote sites. These data indicate that mechanical forces are transferred across discrete cytoskeletal elements over long distances through the cytoplasm in the living adherent cell.

NASA Discipline Cell Biology↗

DOE OSTI2025

Finite element analysis of the impact of beam heating mode in molten salt corrosion experiments employing simultaneous ion irradiation

Finite element analysis was used to investigate the temperature and stress profiles that develop in 316L stainless steel membranes being irradiated using different proton beam conditions in contact with a molten salt environment. It was shown that in addition to a nonuniform irradiation profile, a focused 2 MeV proton beam leads to very strong temperature and stress gradients in the membrane, introducing highly localized driving forces that complicate and even compromise the integrity and reliability of the experimental results of corrosion studies. Here, the use of a focused beam in corrosion studies can create experimental artifacts that may misrepresent the true corrosion behavior. In contrast, the use of a rastered beam is shown to distribute the protons and resulting radiation damage uniformly across the membrane face, and more importantly, results in temperature and stress profiles that are not only very uniform but are of much lower magnitude. The use of a rastered beam during molten salt corrosion experiments is therefore recommended to achieve uniform damage rates, thereby reducing both gradients and magnitudes of the temperature and stress distributions.

43 - PARTICLE ACCELERATORS↗

NASA NTRS1988

A comparison of experimental and calculated thin-shell leading-edge buckling due to thermal stresses

High-temperature thin-shell leading-edge buckling test data are analyzed using NASA structural analysis (NASTRAN) as a finite element tool for predicting thermal buckling characteristics. Buckling points are predicted for several combinations of edge boundary conditions. The problem of relating the appropriate plate area to the edge stress distribution and the stress gradient is addressed in terms of analysis assumptions. Local plasticity was found to occur on the specimen analyzed, and this tended to simplify the basic problem since it effectively equalized the stress gradient from loaded edge to loaded edge. The initial loading was found to be difficult to select for the buckling analysis because of the transient nature of thermal stress. Multiple initial model loadings are likely required for complicated thermal stress time histories before a pertinent finite element buckling analysis can be achieved. The basic mode shapes determined from experimentation were correctly identified from computation.

Jenkins, Jerald M.↗

DOE OSTI2024

Creep and failure at metal-oxide interfaces

Small-scale bicrystal creep experiments were performed on contacts formed via in situ high-temperature diffusion bonding of metal-oxide interfaces including Ag-ZrO 2 , Pd-ZrO 2 , Pt-ZrO 2 , and Ag-high entropy oxide. This work characterizes deformation and failure at metal-oxide interfaces during mechanical loading. Interfacial sliding can be activated easily, while tensile interfacial creep was not observed at any condition of stress or temperature measured. Plastic strain, instead, localizes within the metal under tensile loading. A variety of mechanisms for plastic strain occur in the metal including lattice dislocation-mediated plasticity, twinning, low-angle grain boundary formation, and low-angle grain boundary creep. Surface and low-angle grain boundary diffusion occur under conditions where no metal-oxide tensile creep is observed, highlighting the significant differences in their interfacial mechanical response. High-temperature interfacial failure occurs when the mean curvature at the contact neck is approximately zero and the applied stresses comparable to brittle fracture stresses. The brittle fracture stresses were measured to be σ ƒ = 180 ± 90 MPa at the Ag-ZrO 2 interface at 225 °C, σ ƒ = 460 ± 160 MPa at the Pd-ZrO 2 interface at 680 °C, and σ ƒ = 640 ± 440 MPa at the Pt-ZrO 2 interface at 1010 °C.

Creep↗

DOE OSTI2021

Effect of local structure and stoichiometry on the dynamic behavior of bi-metal interfaces

Molecular dynamics (MD) simulations are performed to investigate the failure behavior of Al/Al, Al/Fe, and Al/AlFe bi-layers under high strain-rate shock loading. Additional simulations are performed to invesigate solely the tensile response of these systems and to isolate the effects of loading history on damage and failure. Specifically, the compression stage of the shock is excluded from the tensile simulations. This study shows that local structure variation, including the introduction of serrations, plays different roles in controlling damage nucleation depending on the specific loading condition. Under shock loading, the stress for void nucleation and the resulting void distribution is insensitive to an interface structure, whereas under pure tensile loading, the opposite is true, even though the strain rate is comparable. The above difference can be explained based on the corresponding change in the total deformation prior to damage nucleation under shock loading, which is missing from the pure tensile loading. Therefore, it is concluded that whether local interface structure matters under high strain-rate loading depends on the specific loading history and the stress state: the local structure variation matters only when it alters the deformation behavior, and subsequently, damage nucleation and evolution.

36 MATERIALS SCIENCE↗

NASA NTRS1987

A comparison of turbulence closure models for transonic flows about airfoils

Navier-Stokes transonic airfoil calculations using three different turbulence closure models are presented and compared with available experimental data. Two of the models, Cebeci-Smith and Baldwin-Lomax, are equilibrium models in the sense that the turbulent shear stress is assumed to depend only on the local properties of the mean flow. The third model, Johnson and King, is a nonequilibrium model in which an ordinary differential equation is employed to account for the streamwise development of the maximum Reynolds shear stress. An eddy viscosity distribution across the boundary layer is assumed which is functionally dependent on this stress. For attached flows with little inviscid-viscous interaction, little difference in the results with the different models is noted. With stronger interactions and with separation occurring on the airfoils, the nonequilibrium model is shown to perform better.

King, Lyndell S.↗

DOE OSTI2024

Multi-stage load partitioning in additively manufactured Al6061+TiC nanocomposite characterized by in-situ neutron diffraction

Metal matrix composites (MMCs), combining metal matrix and ceramic particles, exhibit high mechanical strength and stiffness compared to conventional metallic materials. During fusion-based additive manufacturing (AM), MMCs undergo a rapid heating and cooling thermal history, which affects the interfacial bonding, thermal misfit stress and mechanical load transfer behavior between the metal matrix and particles, thus impacting the bulk mechanical performance. Here, we investigate the deformation dynamics and phase-specific load transfer in fusion-based AMed Al6061 +TiC MMCs through in-situ neutron diffraction. By calculating the phase-specific lattice strains, a multi-stage load transfer and deformation behavior during uniaxial compression is revealed: (1) elastic deformation in Stage I for both phases; (2) sudden stress rebalance between two phases in Stage II, evidenced by a sudden decrease in Al lattice strain and increase in TiC; (3) active load carrying by both phases in Stage III, with both phases experiencing an increase in lattice strains. Further, the deformation mechanism of each stage is deducted by correlating the evolutions of the interphase stresses and peaks’ broadening and intensity of the Al matrix. The local plastic deformation of the Al matrix near the phase interface is triggered and leads to stress rebalancing in Stage II. The global plastic deformation subsequently propagates throughout the Al matrix in Stage III, and the composite is further hardened through both dislocation multiplication and load transfer. The findings offer valuable insights into deformation and load-sharing behavior in AMed MMCs.

36 MATERIALS SCIENCE↗