SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Arcing and field-included surface erosion reduced by electrostatic shields around windings and ferromagnetic core of 80-kilovolt isolation transformer. Fabricated from high-resistivity polyurethane-based material brushed on critical surfaces, shields maintained at approximately half potential difference of windings.
The helicopter version of the Rotor Systems Research Aircraft (RSRA) is designed to make simultaneous measurements of all rotor forces and moments in a manner analogous to a wind-tunnel balance. Loads are measured by a combination of load cells, strain gages, and hydropneumatic active isolators with built-in pressure gages. Complete evaluation of system performance requires calibration of the rotor force- and moment-measurement system when installed in the aircraft. Derivations of calibration corrections for various combinations of calibration data are discussed.
The inertial pointing stability of a gimbal pointing system (AGS) was compared with a magnetic pointing/gimbal followup system (ASPS), under certain conditions of system structural flexibility and disturbance inputs from the gimbal support structure. Separate 3 degree-of-freedom (3DOF) linear models based on NASTRAN modal flexibility data for the gimbal and support structures were generated for the ASPS configurations. Using the models inertial pointing control loops providing 6dB of gain margin and 45 deg of phase margin were defined for each configuration. The pointing loop bandwidth obtained for the ASPS is more than twice the level achieved for the AGS configuration. The AGS limit is attributed to the gimbal and support structure flexibility. As a result of the higher ASPS pointing loop bandwidth and the disturbance rejection provided by the magnetic isolation ASPS pointing performane is significantly better than that of the AGS system. The low frequency peak of the ASPS transfer function from base disturbance to payload angular motion is almost 60dB lower than AGS low frequency peak.
An experimental investigation has been conducted to determine the effect of wing leading edge sweep and wing translation on the aerodynamic characteristics of a wing body configuration at a free stream Mach number of about 6 and Reynolds number (based on body length) of 17.9 x 10 to the 6th power. Seven wings with leading edge sweep angles from -20 deg to 60 deg were tested on a common body over an angle of attack range from -12 deg to 10 deg. All wings had a common span, aspect ratio, taper ratio, planform area, and thickness ratio. Wings were translated longitudinally on the body to make tests possible with the total and exposed mean aerodynamic chords located at a fixed body station. Aerodynamic forces were found to be independent of wing sweep and translation, and pitching moments were constant when the exposed wing mean aerodynamic chord was located at a fixed body station. Thus, the Hypersonic Isolation Principle was verified. Theory applied with tangent wedge pressures on the wing and tangent cone pressures on the body provided excellent predictions of aerodynamic force coefficients but poor estimates of moment coefficients.
The dynamic isolation of a two degree of freedom inertially stabilized science platform from the spacecrft basebody is examined. The important implications of a momentum compensated platform for pointing performance and cost are discussed, and the concept of a new system called the Integrated Platform Pointing and Attitude Control Subsystem utilizing the above property is presented. The results established in this paper are demonstrated by a computer simulation.
Surface analyses and numerical simulation sensitivity studies are compared in order to determine the role played by deep, well-mixed, and well-heated boundary layers in perturbing a weak jet streak in proximity to the development of an isolated but intense convective complex associated with the Grand Island, Nebraska tornado outbreak of June 3-4, 1980. A brief description of the case is first presented, emphasizing three-hourly surface analyses, radar, and satellite data. The results of numerical experiments comparing differences in the runs with and without diurnal surface sensible heating are discussed and related to observations. The dynamical processes responsible for these simulation differences are discussed, and the significance of these differences are considered in terms of their effect on the preconvective environment.
An advanced, sensor failure detection, isolation, and accomodation algorithm has been developed by NASA for the F100 turbofan engine. The algorithm takes advantage of the analytical redundancy of the sensors to improve the reliability of the sensor set. The method requires the controls computer, to determine when a sensor failure has occurred without the help of redundant hardware sensors in the control system. The controls computer provides an estimate of the correct value of the output of the failed sensor. The algorithm has been programmed in FORTRAN using a real-time microprocessor-based controls computer. A detailed description of the algorithm and its implementation on a microprocessor is given.
A decentralized failure detection and isolation (FDI) methodology, which is robust with respect to model uncertainties and noise, is presented Redundancy metrics are developed, and optimization problems are posed for the choices of robust parity relations. Closed-form solutions for some special failure cases are given. Connections are drawn with other disciplines, and the use of the metrics to evaluate alternative FDI schemes is discussed.
After surveying electrically driven loads used on productive farms, the investigators chose three pumps for testing at voltages and frequencies far outside the normal operating range. These loads extract and circulate water and move heat via air, and all are critical to farm productivity. The object was to determine the envelope of supply voltage and frequency over which these loads would operate stably for time intervals under 1 hour. This information is among that needed to determine the feasibility of supplying critical loads, in case of a utility outage, from a wind driven alternator whose output voltage and frequency will vary dramatically in most continental wind regimes. Other related work is surveyed. The salient features and limitations of the test configurations used and the data reduction are described. The development of simulation models suitable for a small computer are outlined. The results are primarily displayed on the voltage frequency plane with the general conclusion that the particular pump models considered will operate over the range of 50 to 90 Hz and a voltage band which starts below rated, decreases as frequency decreases, and is limited on the high side by excessive motor heating. For example, centrifugal pump operating voltage ranges as extensive .4 to 1.4 appear possible. Particular problems with starting, stalling due to lack of motor torque, high speed cavitation, and likely overheating are addressed in a listing of required properties for wind driven alternators and their controllers needed for use in the isolated or stand alone configuration considered.
A summary of recent research at JPL on two topics related to achieving long term reliability of photovoltaic modules: voltage isolation and electrochemical corrosion is presented. Special emphasis is given to similarities and differences in performance between crystalline silicon modules and amorphous silicon modules.
An advanced sensor failure detection, isolation, and accommodation (ADIA) algorithm has been developed for use with an aircraft turbofan engine control system. In a previous paper the authors described the ADIA algorithm and its real-time implementation. Subsequent improvements made to the algorithm and implementation are discussed, and the results of an evaluation presented. The evaluation used a real-time, hybrid computer simulation of an F100 turbofan engine.
For flap-lag stability of isolated rotors, experimental and analytical investigations are conducted in hover and forward flight on the adequacy of a linear quasisteady aerodynamics theory with dynamic inflow. Forward flight effects on lag regressing mode are emphasized. A soft inplane hingeless rotor with three blades is tested at advance ratios as high as 0.55 and at shaft angles as high as 20 degrees. In combination with lag natural frequencies, collective pitch settings and flap-lag coupling parameters, the data base comprises nearly 1200 test points (damping and frequency) in forward flight and 200 test points in hover. By computerized symbolic manipulations, an analytic model is developed in substall to predict stability margins with mode identification. It also predicts substall and stall regions to help explain the correlation between theory and data.
The objective is to extend the recent advances in robust control system design of multivariable systems to sensor failure detection, isolation, and accommodation (DIA), and estimator design. This effort provides analysis tools to quantify the trade-off between performance robustness and DIA sensitivity, which are to be used to achieve higher levels of performance robustness for given levels of DIA sensitivity. An innovations-based DIA scheme is used. Estimators, which depend upon a model of the process and process inputs and outputs, are used to generate these innovations. Thresholds used to determine failure detection are computed based on bounds on modeling errors, noise properties, and the class of failures. The applicability of the newly developed tools are demonstrated on a multivariable aircraft turbojet engine example. A new concept call the threshold selector was developed. It represents a significant and innovative tool for the analysis and synthesis of DiA algorithms. The estimators were made robust by introduction of an internal model and by frequency shaping. The internal mode provides asymptotically unbiased filter estimates.The incorporation of frequency shaping of the Linear Quadratic Gaussian cost functional modifies the estimator design to make it suitable for sensor failure DIA. The results are compared with previous studies which used thresholds that were selcted empirically. Comparison of these two techniques on a nonlinear dynamic engine simulation shows improved performance of the new method compared to previous techniques
An experimental study of the flowfield of heated and unheated single and dual jet configurations was performed. This study of two parallel jets is unique since most previous aerodynamic structure experiments were limited to single round and two-dimensional jets. The present closely spaced dual jet geometry was motivated by the potential jet noise reduction available from this configuration. This geometry has shown promise as a method for redirecting jet noise away from ground based observers in side by side or over/under turbofan engine mountings on aircraft (Simonich et al., 1984). Since the effectiveness of this noise reduction technique is based on the existence of two independent jets, an understanding of the aerodynamics of the merging process is essential to establishing the acoustic benefits. The experimental program was structured so that Mach number, jet exit temperature, and spacing to diameter ratios could be independently varied to isolate each effect.
The design of a pointing system that is applicable for a variety of payloads is examined. The system employs a very soft interface coupled with inertial control torques which use reaction wheels or control moment gyros. The fundamental stability and disturbance rejection characteristics of simple gimbal pointing systems and the soft mounted inertially reacting concept are evaluated and compared. It is observed that in simple and two-stage gimbal systems there is dynamic interaction with the basebody and these types of systems are not applicable for a Space Station/Space Platform environment in which system dynamics are uncertain; however, the soft mounted inertially reacting concept minimizes the dynamic interaction with the basebody and retains stability. It is concluded that the soft mounted inertially reacting concept has the pointing accuracy and disturbance isolation of a free flying spacecraft while still obtaining power, communication, orbit maintenance, and servicing from a basebody.
This paper develops a framework for the design of failure detection and isolation (FDI) algorithms. Rather than trying to apply 'optimal' techniques in a top-down manner, the system redundancies are evaluated with respect to their ability to provide reliable FDI information. Previous work of Pattipati et al. (1984) and Weiss et al. (1984) defined a useful context and several useful analytical results, which provide a basis for the FDI design methodology developed here. A general decision structure which can take advantage of redundancy evaluation is presented, and examples of typical design considerations are discussed. The operation of the decision structure is then demonstrated for a sensor FDI application involving the F-100 jet engine.
Recent advances in multivariable robust control system design are extended to sensor failure, detection, isolation, and accommodation (FDIA) and estimator design. A new concept called threshold selector is introduced. It represents a significant and innovative tool for the analysis and synthesis of FDIA algorithms. Analytical results are obtained for the SISO case to compute optimal thresholds and size of minimum detectable failures, and a computer-aided technique is developed for the multivariable case. The techniques have been applied to sensor FDIA for an aircraft turbine engine control system.
Efficient voltage converter employs capacitive instead of transformer coupling to provide dc isolation. Offers buck/boost operation, minimal filtering, and low parts count, with possible application in photovoltaic power inverters, power supplies and battery charges. In photovoltaic inverter circuit with transformerless converter, Q2, Q3, Q4, and Q5 form line-commutated inverter. Switching losses and stresses nil because switching performed when current is zero.