SEARCH · Engineering Papers

Results for “flow visualization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

All sources NASA NTRS DOE OSTI

NASA NTRS1975

Aerodynamic sound generation due to the interaction of an unsteady wake with a rigid surface

Some aspects of sound generation by the interaction between a wedge and the wake of a circular cylinder in a uniform incompressible stream are studied experimentally. There is a minimum separation distance between the cylinder and the wedge when a tone is first generated. As the separation distance increases beyond the minimum, the frequency increases and asymptotically approaches the frequency normally present in the free wake. The Strouhal number defined as the ratio fd/U where f is the frequency, d is the cylinder diameter and U the free-stream speed is found to be in general a function of the Reynolds number (based on d) and h/d, where h is the separation distance. The minimum distance is in general a function of the Reynolds number. Flow visualization studies show that considerable differences exist between the flow below the minimum separation distance and just above it.

Smith, C. A.↗

NASA NTRS1985

Flow control in a diffusing S-Duct

Accurate measurements have been made of secondary flow in a 1.51 area ratio diffusing 30 deg - 30 deg S-Duct with circulair cross section. Turbulent flow was entering the duct at Mach number of 0.6, the boundary layer thickness at the duct entrance was ten percent of the duct inlet diameter. Through measurements made, local flow velocity vector as well as static and total pressures mapping of the flow at several stations were obtained. Strong secondary flow was measured in the first bend which continued into the second bend with new vorticity produced in there in the opposite direction. Surface oil flow visualization and wall pressures indicated a region of separated flow starting at theta approximately equal to 22 deg on the inside of the first bend up to theta approximately equal to 44 deg on the outside of the second bend. The flow separated in 'cyclone' form and never reattached in the duct. As a result of the secondary flow and the flow separation, significant total pressure distortion was observed at the exit of the duct. Using flow control devices the separation was eliminated while the exit distortion was improved.

Vakili, A. D.↗

NASA NTRS1987

Comparison of experimental and computational techniques for plane mixing layers

In this paper, results from two experimental and two computational investigations of plane turbulent mixing layers are presented and compared. The experimental results include flow visualization data using the smoke laser technique and mean flow and turbulence measurements obtained with hot X-wires and a two-component LDV. Reasonably good agreement is found among these techniques, at least for turbulence quantities up to second order. Reynolds-averaged computations are successful at capturing the complete evolution of the mixing layer, including wake effects in the near field and approach to self-preservation in the far field. The two-dimensional vortex method shows excellent qualitative and quantitative agreement with measured data for the forced mixing layer. For the unforced layer, the results seem to indicate that a three-dimensional computation may be necessary.

Mehta, R. D.↗

NASA NTRS1989

On the separated flow upstream of a jet in a cross flow

Flow visualization techniques have been used to investigate the complex flow in the recirculation region upstream of a rectangular jet issuing normally into a uniform cross flow. Two different flow regimes are identified. It is shown that the recirculation region upstream of the jet is unsteady and periodic. Two distinct vortical structures are found for the wake behind the jet, one dominated by a symmetric vortex pair and one with vortices shed alternately from each side of the jet.

Krothapalli, A.↗

NASA NTRS1988

Wind-tunnel investigation of the low-speed aerodynamics of slender accelerator-type configurations

The NASA-Langley 14x22-ft subsonic wind tunnel has been used to ascertain the low speed aerodynamics of a conical-forebody/annular conformal propulsion system/truncated conical afterbody hypersonic-accelerator configuration with delta-planform wing. Six-component force-and-moment data were obtained over the -4 to +30 deg alpha range and + or - 20 deg sideslip. Flow visualization diagnostics were used to characterize configuration aerodynamics. Vortex flows from the conical forebody created large values of local inflow angles at the engine inlet locations on the lee side of the model, at the moderate-alpha values associated with takeoff and landing.

Gatlin, Gregory M.↗

NASA NTRS1991

Progress toward synergistic hypermixing nozzles

Mean flow measurements have been obtained for air-to-air mixing downstream of swept and unswept ramp wall-mounted hypermixing nozzle configurations. Aside from the sweep of the ramps, the two nozzle configurations investigated are identical. The nozzles inject three parallel supersonic jets at a 15-deg angle (relative to the wind tunnel wall) into a supersonic freestream. Mach number and volume fraction distributions in a transverse plane 11.1 nozzle heights downstream from the nozzle exit plane were measured. Data are presented for a freestream Mach number of three at a matched static pressure condition and also at an underexpanded static pressure condition (pressure ratio equal to 5). Surface oil flow visualization was used to investigate the near-wall flow behavior. The results indicate that the swept ramp injectors produce stronger and larger vortex pairs than the unswept ramp injectors. The increased interaction between the swept ramp model's larger vortex pairs yields better mixing characteristics for this model.

Davis, D. O.↗

NASA NTRS1953

Smoke Studies of Secondary Flows in Bends, Tandem Cascades, and High-turning Configurations

Flow-visualization studies, using smoke, were made of the secondary flows in rectangular bends, tandem cascades, and high-turning configurations. The roll-up of the wall boundary layer of a rectangular bend forms a passage vortex near the suction surface similar to that previously observed for cascades. The vortex so formed then shifts out into the main stream. Because of leading-edge effects, the boundary-layer flows in bends were found to be sufficiently different from the flows in blade rows to make direct application of bend results to blade rows inadvisable. Passage vortices are shown, in the tandem-cascade study, to resist turning with the main stream through which they pass and to disturb the flow in subsequent blade rows. This disturbance may explain in part the appreciable size of the losses sometimes attributed to secondary flows in turbomachines despite the fact that the energy involvement in vortex formation is slight. Tip-flow studies of high-turning blades with relative motion between blades and end wall indicated that if the relative sizes of the passage vortex forces, the tip clearance forces, and the blade-scraping effects are properly controlled, it may be possible to improve the blade-tip loading characteristics in turbomachine.

CASCADES↗

NASA NTRS2005

Navier-Stokes Simulation of Airconditioning Facility of a Large Modem Computer Room

NASA recently assembled one of the world's fastest operational supercomputers to meet the agency's new high performance computing needs. This large-scale system, named Columbia, consists of 20 interconnected SGI Altix 512-processor systems, for a total of 10,240 Intel Itanium-2 processors. High-fidelity CFD simulations were performed for the NASA Advanced Supercomputing (NAS) computer room at Ames Research Center. The purpose of the simulations was to assess the adequacy of the existing air handling and conditioning system and make recommendations for changes in the design of the system if needed. The simulations were performed with NASA's OVERFLOW-2 CFD code which utilizes overset structured grids. A new set of boundary conditions were developed and added to the flow solver for modeling the roomls air-conditioning and proper cooling of the equipment. Boundary condition parameters for the flow solver are based on cooler CFM (flow rate) ratings and some reasonable assumptions of flow and heat transfer data for the floor and central processing units (CPU) . The geometry modeling from blue prints and grid generation were handled by the NASA Ames software package Chimera Grid Tools (CGT). This geometric model was developed as a CGT-scripted template, which can be easily modified to accommodate any changes in shape and size of the room, locations and dimensions of the CPU racks, disk racks, coolers, power distribution units, and mass-storage system. The compute nodes are grouped in pairs of racks with an aisle in the middle. High-speed connection cables connect the racks with overhead cable trays. The cool air from the cooling units is pumped into the computer room from a sub-floor through perforated floor tiles. The CPU cooling fans draw cool air from the floor tiles, which run along the outside length of each rack, and eject warm air into the center isle between the racks. This warm air is eventually drawn into the cooling units located near the walls of the room. One major concern is that the hot air ejected to the middle isle might recirculate back into the cool rack side and cause thermal short-cycling. The simulations analyzed and addressed the following important elements of the computer room: 1) High-temperature build-up in certain regions of the room; 2) Areas of low air circulation in the room; 3) Potential short-cycling of the computer rack cooling system; 4) Effectiveness of the perforated cooling floor tiles; 5) Effect of changes in various aspects of the cooling units. Detailed flow visualization is performed to show temperature distribution, air-flow streamlines and velocities in the computer room.

Source record↗

DOE OSTI2026

Holistic energy analysis method for thermal management architectures of data centers

Modern high-performance computing (HPC) data centers (DCs), particularly those supporting energy-intensive artificial intelligence (AI) workloads, face escalating thermal management challenges that degrade performance through thermal throttling and drive up cooling power consumption and operational costs. To address this challenge, many have developed a wide variety of thermal management solutions (single-phase, two-phase, direct, indirect, hybrid, and more) which attempt to cool HPC DCs effectively while attempting to minimize overall system power consumption. However, the analysis of these solutions and methods to effectively compare one with another is lacking. Overall power usage effectiveness (PUE) and total-power usage effectiveness (TUE) provide a metric to quantify power consumption but fail to identify components in the system which require further optimization. To address this, we propose a holistic analytical framework – the waterfall diagram (WFD) – which leverages a waterfall chart methodology, offering a comprehensive visualization of both the thermal management system loop and heat flow pathways from individual server components to the outdoor ambient. Use of the WFD enables graphical estimations of power efficiency and cooling performance across each component of a DC cooling system and complements Sankey-style energy flow visualizations by additionally resolving stage-wise temperature changes and incremental TUE contributions. The framework is used in conjunction with simulation-based approaches, to conduct a detailed pressure drop and flow distribution analysis aimed at identifying the optimal coolant distribution architecture for a single-phase direct-to-chip water-cooled DC, which serves as the baseline for subsequent WFD analysis. Among the evaluated architectures, the 3 U modular coolant distribution architecture is found to demonstrate the best performance, considering minimal pressure drop and uniform flow distribution. In addition, TUE is calculated for each cooling loop component based on its associated pressure drop and corresponding pumping power, which are integrated into the WFD. This correlation between TUE and local temperature offers immediate insight into the power efficiency and thermal performance contributions of individual components, facilitating further development and optimization. Examples of WFD applications are presented under varying thermal loads and ambient conditions, demonstrating reasonable cooling strategies. Notably, the 3 U modular architecture maintains a consistent chip case temperature of 85°C, achieving a TUE of 1.016 at ambient temperature of 47°C, and a TUE of 1.026 at ambient temperature of 52°C. The WFD methodology provides an efficient, holistic, and streamlined framework for DC thermal management architecture assessment and enables design optimization which is important for addressing the thermal-fluidic energy challenges of current and next-generation DCs.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2021

Flow over an espresso cup: inferring 3-D velocity and pressure fields from tomographic background oriented Schlieren via physics-informed neural networks

Tomographic background oriented Schlieren (Tomo-BOS) imaging measures density or temperature fields in three dimensions using multiple camera BOS projections, and is particularly useful for instantaneous flow visualizations of complex fluid dynamics problems. We propose a new method based on physics-informed neural networks (PINNs) to infer the full continuous three-dimensional (3-D) velocity and pressure fields from snapshots of 3-D temperature fields obtained by Tomo-BOS imaging. The PINNs seamlessly integrate the underlying physics of the observed fluid flow and the visualization data, hence enabling the inference of latent quantities using limited experimental data. In this hidden fluid mechanics paradigm, we train the neural network by minimizing a loss function composed of a data mismatch term and residual terms associated with the coupled Navier–Stokes and heat transfer equations. We first quantify the accuracy of the proposed method based on a two-dimensional synthetic data set for buoyancy-driven flow, and subsequently apply it to the Tomo-BOS data set, where we are able to infer the instantaneous velocity and pressure fields of the flow over an espresso cup based only on the temperature field provided by the Tomo-BOS imaging. Moreover, we conduct an independent PIV experiment to validate the PINN inference for the unsteady velocity field at a centre plane. To explain the observed flow physics, we also perform systematic PINN simulations at different Reynolds and Richardson numbers and quantify the variations in velocity and pressure fields. Furthermore, the results in this paper indicate that the proposed deep learning technique can become a promising direction in experimental fluid mechanics.

97 MATHEMATICS AND COMPUTING↗

NASA NTRS1986

Flow diagnostics and visualization in wind tunnels and flight

The Langley Research Center has a concentrated and directed effort under way to develop both conventional and non-intrusive diagnostic instrumentation. These instruments are being developed to operate over large Mach number, total temperature, and total pressure ranges. Efforts are being made to evaluate the measurements made by the various instruments to determine the most accurate and reliable instrument to be used under a given flow environment. Although only one flow visualization technique was described, there are many different types presently being used at Langley Research Center.

Stainback, P. C.↗

NASA NTRS1973

An experimental investigation of three oblique-wing and body combinations at Mach numbers between 0.60 and 1.40

An experimental investigation was conducted in an 11- by 11-foot transonic wind tunnel to determine the aerodynamic characteristics of three oblique high aspect ratio wings in combination with a high fineness-ratio Sears-Haack body. The three wings had the same elliptical planform and base line curvature but had different airfoil sections. One wing had an airfoil section designed to have a lift coefficient of 1.0 at a Mach number of 0.7, another to have shock-free supersonic flow over the upper surface, and the other to have a lift coefficient of 1.3 at a Mach number of 0.6. Longitudinal and lateral-directional stability data were obtained at wing yaw angles of 0 deg, 45 deg, 50 deg, and 60 deg over a test Mach number range from 0.6 to 1.4 for angles of attack between minus 7 deg and 9 deg. Reynolds numbers for the study were 4 and 6 million per foot. Flow-visualization studies were made to examine the nature of the flow on the wing surfaces. Notable differences were found in the aerodynamic characteristics of the three wing-body combinations, particularly in the lateral-directional characteristics.

Graham, L. A.↗

NASA NTRS1972

An experimental investigation of an oblique-wing and body combination at Mach numbers between 0.60 and 1.40

An experimental investigation was conducted in an 11- by 11-foot wind tunnel to determine the aerodynamic characteristics of an oblique high aspect ratio wing in combination with a high fineness-ratio Sears-Haack body. Longitudinal and lateral-directional stability data were obtained at wing yaw angles from 0 deg to 60 deg over a test Mach number range from 0.6 to 1.4 for angles of attack between minus 6 deg and 9 deg. The effects of changes in Reynolds number, dihedral, and trailing-edge angle were studied along with the effects of a roughness strip on the upper and lower surfaces of the wing. Flow-visualization studies were made to determine the nature of the flow on the wing surfaces.

Graham, L. A.↗

NASA NTRS1972

Lee-side vortices on delta wings at hypersonic speeds.

A fluid-dynamic investigation was carried out to determine the cause of intense heating observed on the lee meridian of hypersonic delta wings and also to derive means for its suppression. Several experimental techniques were combined with analysis of extensive heat-transfer measurements at a freestream Mach number of six in a range of Reynolds number to acquire a general description of the lee-flow structure. With attached leading-edge flow on the delta wings, the dominant feature is a pair of embedded vortices on the lee meridian whose interaction with the boundary-layer is responsible for the observed local heating. On the basis of flow visualization results and heat-transfer correlations, a qualitative vortex flow model is proposed which differs essentially from the conventional inboard separation vortex model.

Rao, D. M.↗

NASA NTRS1977

Disrupted states of vortex flow and vortex breakdown

Flow visualization studies and laser Doppler anemometer measurements on swirling water flows reveal six distinct types of very large amplitude disturbance modes of the vortex core. Three, 'axisymmetric' and spiral vortex breakdowns, and the 'double helix,' have been described by others. A definite order of evolution in parameter space (Reynolds number and circulations) occurs, and is described. Puzzling responses of the axisymmetric and spiral vortex breakdowns to imposed flow transients reported previously are confirmed here, and are traced to the shedding of starting and stopping vortices from swirl vanes. Conclusions bearing upon the validity of some theories of vortex breakdown are possible from the data.

Faler, J. H.↗

NASA NTRS1980

Development of a Kevlar/PMR-15 reduced drag DC-9 nacelle fairing

The paper describes an advanced composite fairing designed to reduce drag on DC-9 nacelles as a part of the NASA Engine Component Improvement Program. This fairing is the aft enclosure for the thrust reverser actuator system on JT8D engine nacelles and is subjected to a 500 F exhaust flow during the reverse thrust. A reduced-drag configuration was developed by using in-flight tuft surveys for flow visualization in order to identify areas with low-quality flow, and then modifying the aerodynamic lines to improve the flow. A fabrication method for molding the part in an autoclave was developed; this material system is suitable for 500 F. The resultant composite fairing reduces the overall aircraft drag 1% with a weight reduction of 40% when compared with a metal component.

Kawai, R. T.↗

NASA NTRS1982

Transonic aerodynamics; Transonic Perspective Symposium, Moffett Field, CA, February 18-20, 1981, Technical Papers

After an historical account of the development of transonic aerodynamics before 1940 and in the period 1945-1975, attention is given to the design for cruise performance efficiency of commercial transport aircraft, with emphasis on transonic wing design, the practical aerodynamic problems of military aircraft, with emphasis on store carriage and separation, experimental testing in transonic wind tunnels capable of Reynolds number simulation and aerodynamic flow visualization, and such mathematical techniques as potential equation methods for flow prediction and Reynolds-averaged Navier-Stokes computations of transonic flows. Also considered are transonic design using computational aerodynamics, the application of computation methods to transonic wing design, computational experience with advanced tactical aircraft, the evaluation of full potential flow methods, and the application of a shock-turbulent boundary layer interaction theory to transonic flowfield analysis.

Nixon, D.↗

NASA NTRS1983

Mass and Momentum Turbulent Transport Experiments

The downstream mixing of coaxial jets discharging in an expanded duct was studied to improve turbulent transport models which are used in computational procedures throughout the propulsion community for combustor flow modeling. Laser velocimeter (LV) and laser induced fluorescence (LIF) techniques were used to measure velocities and concentration and flow visualization techniques to determine the time dependent characteristics of the flow and the scale of the turbulent structure.

Johnson, B. V.↗