SEARCH · Engineering Papers

Results for “first wall”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

All sources NASA NTRS DOE OSTI

NASA NTRS1993

Analysis of the Harrier forebody/inlet design using computational techniques

Under the support of this Cooperative Agreement, computations of transonic flow past the complex forebody/inlet configuration of the AV-8B Harrier II have been performed. The actual aircraft configuration was measured and its surface and surrounding domain were defined using computational structured grids. The thin-layer Navier-Stokes equations were used to model the flow along with the Chimera embedded multi-grid technique. A fully conservative, alternating direction implicit (ADI), approximately-factored, partially flux-split algorithm was employed to perform the computation. An existing code was altered to conform with the needs of the study, and some special engine face boundary conditions were developed. The algorithm incorporated the Chimera technique and an algebraic turbulence model in order to deal with the embedded multi-grids and viscous governing equations. Comparison with experimental data has yielded good agreement for the simplifications incorporated into the analysis. The aim of the present research was to provide a methodology for the numerical solution of complex, combined external/internal flows. This is the first time-dependent Navier-Stokes solution for a geometry in which the fuselage and inlet share a wall. The results indicate the methodology used here is a viable tool for transonic aircraft modeling.

Chow, Chuen-Yen↗

NASA NTRS2001

Interpretation of a Magnetic Map of the Valles Marineris Region, Mars

A magnetic map of Valles Marineris is interpreted in terms of left-lateral faulting, the first evidence for substantial strike-slip faulting here. Surface exposures of highly magnetic material may exist in the walls of Valles Marineris. Additional information is contained in the original extended abstract.

Purucker, M. E.↗

NASA NTRSDate not supplied

Mechanical Erosion Modeling of TPS Materials

This work describes the development of a model that accounts for the additional total surface recession in Thermal Protection Systems materials as a result of mechanical erosion due to high shear conditions during atmospheric entry. A computational solid mechanics capability module was integrated within the Porous material Analysis Toolbox based on OpenFOAM, PATO. The mechanical erosion was modeled in three steps: first, the implemented stress analysis solver module computes the stress and the displacement fields for orthotropic materials using the wall shear stress tensor as a boundary condition; then, regions on the surface where the stress meets the failure criteria are identified; and last, the mesh is moved accordingly to remove the failed material. The outcome is a model of the total recession of the material due to surface chemistry and mechanical erosion. Results will be included in the final paper after verifying and completing the study.

Stress Analysis↗

DOE OSTI2024

Validation study of RWM stability in DIII-D high- β N plasmas

The n = 1 (n is the toroidal mode number) resistive wall mode (RWM) stability is numerically investigated for two DIII-D high-β N discharges 176440 and 172461, utilizing the MARS-F (Liu et al 2000 Phys. Plasmas 7 3681) and MARS-K (Liu et al 2008 Phys. Plasmas 15 112503) codes. Systematic validation efforts are attempted, for the first time, for discharges with very slow or vanishing toroidal flow for a large fraction of the plasma volume. While gaining physics insights in accessing stable operation regime at β N exceeding the Troyon no-wall limit in these slow-rotation experiments, the predictive capability of fluid and non-perturbative magnetohydrodynamic-kinetic hybrid models for the RWM is further confirmed. The MARS-F fluid model, with a strong but numerically tunable viscosity mimicking ion Landau damping of parallel sound waves, finds complete stabilization of the n = 1 RWM in the considered DIII-D plasmas under the experimental flow conditions. Similarly, either full stabilization (for discharge 176440) or marginal stability (for discharge 172461) of the mode is computed by the MARS-K hybrid model, which is first-principle based without free model parameters. In particular, all drift kinetic resonances, including those of thermal and energetic particles, are found to synergistically act to marginally stabilize the RWM in discharge 172461. These MARS-F/K modeling results explain the experimentally observed stable operational regime in DIII-D, as far as the RWM stability is concerned. Extensive numerical sensitivity studies, with respect to the plasma toroidal flow speed as well as the radial location of the resistive wall, are also carried out to further support the validation study.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NASA NTRSDate not supplied

Separation and Transition on the ROTEX-T Cone-Flare

As part of NATO STO AVT-346 “Predicting Hypersonic Boundary-Layer Transition on Complex Geometries,” coordinated experimental and computational studies were conducted on the ROTEX-T, a cone-flare geometry used in a successful flight-test experiment. At the as-flown conditions, a separation bubble existed at the compression corner. Separation, reattachment, and the multifaceted linear instability paths leading this bubble to transition to turbulence are challenging to predict, but have significant impact on surface pressure and heat flux. High-resolution background-oriented schlieren and infrared thermography measurements were made in the AFOSR–Notre Dame Large Mach-6 Quiet Tunnel at freestream unit Reynolds numbers from 5.8×10(exp 6) to 12.2×10(exp 6) m-1and nominally zero angle of attack. High-speed self-aligned focusing schlieren, infrared thermography, and focused laser differential interferometry measurements were made in the AFRL Mach-6 Ludwieg Tube from 2.2×10(exp 6) to 24.7×10(exp 6) m-1and nominally zero degrees angle of attack. The surface heat-flux and Stanton number distributions were computed. Separation and reattachment locations, as well as the flow state at each, were determined from the combination of surface and off-wall measurements. The convective and global boundary-layer instabilities of the axisymmetric laminar flow at the experimental conditions were investigated computationally. Amplification of Mack’s first and second modes were observed to have logarithmic amplification factors between 5 to 7.5 at the separation location, depending on conditions. The flow was found to be globally unstable to stationary three-dimensional disturbances concentrated in the reattachment region. Previous analysis of the ROTEX-T flight data had not assessed reattachment location or the flow state upon reattachment. Thanks to the insights gained from the coordinated, on- and off-wall ground-test measurements, these evaluations have now been made. The separation location indicated by laminar simulations is consistently numerically predicted to be upstream of the experimentally observed location for a transitional separation bubble. The cause of this difference is understood to lie in the steady-state and axisymmetric assumptions made by both solvers employed to compute the basic states analyzed, as flow topology considerations assert that unsteady two-dimensional or axisymmetric separation bubbles are structurally unstable and will become three-dimensional. Computed laminar heating rates prior to separation agreed well with experiment; transitional heating rates after reattachment were between laminar and turbulent computations.

CFD Validation↗

NASA NTRSDate not supplied

Separation and Transition on the ROTEX-T Cone-Flare

CFD Validation↗

NASA NTRS2011

Axisymmetric Implementation for 3D-Based DSMC Codes

The primary objective in developing NASA s DSMC Analysis Code (DAC) was to provide a high fidelity modeling tool for 3D rarefied flows such as vacuum plume impingement and hypersonic re-entry flows [1]. The initial implementation has been expanded over time to offer other capabilities including a novel axisymmetric implementation. Because of the inherently 3D nature of DAC, this axisymmetric implementation uses a 3D Cartesian domain and 3D surfaces. Molecules are moved in all three dimensions but their movements are limited by physical walls to a small wedge centered on the plane of symmetry (Figure 1). Unfortunately, far from the axis of symmetry, the cell size in the direction perpendicular to the plane of symmetry (the Z-direction) may become large compared to the flow mean free path. This frequently results in inaccuracies in these regions of the domain. A new axisymmetric implementation is presented which aims to solve this issue by using Bird s approach for the molecular movement while preserving the 3D nature of the DAC software [2]. First, the computational domain is similar to that previously used such that a wedge must still be used to define the inflow surface and solid walls within the domain. As before molecules are created inside the inflow wedge triangles but they are now rotated back to the symmetry plane. During the move step, molecules are moved in 3D but instead of interacting with the wedge walls, the molecules are rotated back to the plane of symmetry at the end of the move step. This new implementation was tested for multiple flows over axisymmetric shapes, including a sphere, a cone, a double cone and a hollow cylinder. Comparisons to previous DSMC solutions and experiments, when available, are made.

Stewart, Benedicte↗

NASA NTRS1991

Interaction of two glancing, crossing shock waves with a turbulent boundary-layer at various Mach numbers

A preliminary experimental investigation was conducted to study two crossing, glancing shock waves of equal strengths, interacting with the boundary-layer developed on a supersonic wind tunnel wall. This study was performed at several Mach numbers between 2.5 and 4.0. The shock waves were created by fins (shock generators), spanning the tunnel test section, that were set at angles varying from 4 to 12 degrees. The data acquired are wall static pressure measurements, and qualitative information in the form of oil flow and schlieren visualizations. The principle aim is two-fold. First, a fundamental understanding of the physics underlying this flow phenomena is desired. Also, a comprehensive data set is needed for computational fluid dynamic code validation. Results indicate that for small shock generator angles, the boundary-layer remains attached throughout the flow field. However, with increasing shock strengths (increasing generator angles), boundary layer separation does occur and becomes progressively more severe as the generator angles are increased further. The location of the separation, which starts well downstream of the shock crossing point, moves upstream as shock strengths are increased. At the highest generator angles, the separation appears to begin coincident with the generator leading edges and engulfs most of the area between the generators. This phenomena occurs very near the 'unstart' limit for the generators. The wall pressures at the lower generator angles are nominally consistent with the flow geometries (i.e. shock patterns) although significantly affected by the boundary-layer upstream influence. As separation occurs, the wall pressures exhibit a gradient that is mainly axial in direction in the vicinity of the separation. At the limiting conditions the wall pressure gradients are primarily in the axial direction throughout.

Hingst, Warren R.↗

NASA NTRS1987

Flow in out-of-plane double S-bends

An experimental investigation of developing flows through a combination of out-of-plane S-bend ducts was conducted to gain insight into the redirection of flow in geometries similar to those encountered in practical aircraft wing-root intake ducts. The present double S-bend was fabricated by placing previously investigated S-ducts and S-diffusers in series and with perpendicular planes of symmetry. Laser-Doppler anemometry was employed to measure the three components of mean velocity, the corresponding rms quantities, and Reynolds stresses in the rectangular cross-section ducts. Due to limited optical access, only two mean and rms velocity components were resolved in the circular cross-section ducts. The velocity measurements were complemented by wall static pressure measurements. The data indicates that the flows at the exit are complex and asymmetric. Secondary flows generated by the pressure field in the first S-duct are complemented or counteracted by the secondary flows produced by the area expansion and the curvature of the S-diffuser. The results indicate the dominance of the inlet conditions and geometry upon the development of secondary flows and demonstrate that the flows are predominantly pressure-controlled. The pressure distribution caused by the duct geometry determines the direction and magnitude of the bulk flow while the turbulence dictates the mixing characteristics and profiles in the near wall region.

Schmidt, M. C.↗

DOE OSTI2022

Loading direction dependence of asymmetric response of pyramidal slip in rolled AZ31 magnesium alloy

Textured magnesium alloys usually exhibit anisotropic mechanical behavior due to the asymmetric activation of different twinning and slipping modes. This work focuses on the pyramidal slip responses of rolled AZ31 magnesium alloy under two loading conditions, compressive and tensile loading along the normal direction. Under the condition where the compressive loading direction is closely parallel to the c-axis of the unit cell, tensile twinning and basal slips are prohibited, dislocations then active and tend to accumulate at grain boundaries and form dislocation walls. Meanwhile, these dislocations exhibit zigzag morphologies, which result from the cross-slip from {$10\bar{1}1$} first-order pyramidal plane to {$11\bar{2}2$} second-order pyramidal plane, then back to {$10\bar{1}1$} first-order pyramidal plane. Under the condition where tensile twins are prevalent, {$10\bar{1}1$} first-order and {$11\bar{2}2$} second-order pyramidal dislocations are favorable to be activated. Both types of dislocations behave climb-like dissociations onto the basal plane, forming zigzag dislocations. first-order pyramidal plane to second-order pyramidal plane, then back to first-order pyramidal plane. Under the condition where tensile twins are prevalent, first-order and second-order pyramidal dislocations are favorable to be activated. Both types of dislocations behave climb-like dissociations onto the basal plane, forming zigzag dislocations.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Baryon and lepton number violation from gravitational waves

Not Available

79 ASTRONOMY AND ASTROPHYSICS↗

DOE OSTI2025

Hadronic light-by-light contribution to the muon anomaly from lattice QCD with infinite volume QED at physical pion mass

The hadronic light-by-light scattering contribution to the muon anomalous magnetic moment, (g–2)⁢/2, is computed in the infinite volume QED framework with lattice QCD. We report $a^{HLbL}_μ$ = 12.47⁢(1.15)⁢(0.95) ×10 –10 where the first error is statistical and the second systematic. The result is mainly based on the 2+1 flavor Möbius domain wall fermion ensemble with inverse lattice spacing a –1 = 1.73 GeV, lattice size L = 5.5 fm, and m π = 139 MeV, generated by the RBC-UKQCD collaborations. The leading systematic error of this result comes from the lattice discretization. This result is consistent with previous determinations.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

NASA NTRS1967

Surveyor III A preliminary report

Near the eastern shore of Oceanus Procellarum, 390 miles from Surveyor I, stands Surveyor III, now motionless and silent after a full lunar day's work during which the spacecraft transmitted to Earth 6315 photographs of its surroundings. A surface sampler, operated by command from the Earth and in view of Surveyor's television camera, conducted many tests of the character and structure of the lunar surface material, as well as digging four trenches. While Surveyor I put man's eyes on the Moon, Surveyor III added an arm and a hand with which to work. In this mission, Surveyor displayed remarkable adaptability and stability. Because the engines did not cut off before touchdown, the spacecraft in effect made three separate landings, giving information on surface bearing strength in several places. The spacecraft came to rest at an angle of about 14° from the vertical, well below the rim of a crater, making possible a detailed study of the floor and walls of a small lunar crater. The tilted position of the spacecraft also made it possible to obtain, for the first time from the surface of the Moon, photographs of a solar eclipse, and of the Earth in color. This report presents the preliminary findings from Surveyor III of the team of scientists and engineers of the Surveyor Program.

Surface property↗

NASA NTRS1979

Tests of NASA ceramic thermal barrier coating for gas-turbine engines

A NASA ceramic thermal barrier coating (TBC) system was tested by industrial and governmental organizations for a variety of aeronautical marine, and ground-based gas-turbine engine applications. This TBC is a two-layer system with a bond coating of nickel-chromium-aluminum-yttrium (Ni-16Cr-6Al-0.6Y, in wt %) and a ceramic coating of yttria stabilized zirconia (ZrO2-12Y2O3, in wt %). Tests (Liebert and Stenka, 1979) have been conducted to determine corrosion resistance, thermal protection, durability, thermal conductivity, and fatigue characteristics. The information presented covers some of the significant test results obtained on the first three items. The information also includes photographs of coated parts after tests, measurements of coating loss, amount of metal wall temperature reduction when the TBC is used, and extent of base metal corrosion.

Liebert, C. H.↗

NASA NTRS1987

A transition detection study using a cryogenic hot film system in the Langley 0.3-meter transonic cryogenic tunnel

A transition detection study was conducted in the Langley 0.3-Meter Transonic Cryogenic Tunnel (0.3-m TCT) using a specialized hot film system designed specifically for use in cryogenic wind tunnels. The quantitative transition location data obtained at near cryogenic conditions, 360 deg R (200K) represents the first definitive transition Reynolds numbers obtained in a cryogenic wind tunnel. The model was tested at both adiabatic and nonadiabatic wall conditions with a wall-to-total temperature ratio as low as 0.47. The test results indicated an improved technique for hot-film installation and a modified data acquisition system would allow the on-line determination of the location of boundary layer transition in cryogenic wind tunnels, such as the U.S. National Transonic Facility.

Johnson, C. B.↗

NASA NTRS1988

Primitive numerical simulation of circular Couette flow - Carrousel wind tunnel nonturbulent solutions

The azimuthal-invariant, three-dimensional cylindrical, incompressible Navier-Stokes equations are solved to steady state for a finite-length, physically realistic model. The numerical method relies on an alternating-direction implicit scheme that is formally second-order accurate in space and first-order accurate in time. The equations are linearized and uncoupled by evaluating variable coefficients at the previous time iteration. Wall grid clustering is provided by a Roberts transformation in radial and axial directions. A vorticity-velocity formulation is found to be preferable to a vorticity-streamfunction approach. Subject to no-slip, Dirichlet boundary conditions, except for the inner cylinder rotation velocity (impulsive start-up) and zero-flow initial conditions, nonturbulent solutions are obtained for sub- and supercritical Reynolds numbers of 100 to 400 for a finite geometry where R(outer)/R(inner) = 1.5, H/R(inner) = 0.73, and H/Delta-R = 1.5. An axially-stretched model solution is shown to asymptotically approach the one-dimensional analytic Couette solution at the cylinder midheight. Flowfield change from laminar to Taylor-vortex flow is discussed as a function of Reynolds number. Three-dimensional velocities, vorticity, and streamfunction are presented via two-dimensional graphs and three-dimensional surface and contour plots.

Hasiuk, Jan↗

NASA NTRS1989

Asymptotic structure and similarity solutions for three-dimensional turbulent boundary layers

The asymptotic structure of the three-dimensional turbulent boundary layer is investigated in the limit of large Reynolds numbers. A self-consistent, but relatively complex, two-layer structure exists and the simplest situation, corresponding to a plane of symmetry, is considered in this paper as a first step. The adjustment of the streamwise velocity to relative rest, through an outer defect layer and then an inner wall layer, is similar to that in two-dimensional flow. The adjustment of the cross-streamwise velocity is more complicated and it is shown that two terms in the expansion are required to obtain useful results, and in particular to obtain the velocity skew angle at the wall near the symmetry plane. The conditions under which self-similarity is achieved near a plane of symmetry are investigated. A set of ordinary differential equations is developed which describe the streamwise and cross-streamwise velocities near a plane of symmetry in a self-similar flow through two orders of magnitude. Calculated numerical solutions of these equations yield trends which are consistent with experimental observations.

Degani, A. T.↗

NASA NTRS1990

Advanced Mach 3.5 Axisymmetric Quiet Nozzle

To advance boundary-layer stability and transition research and to ultimately provide reliable predictions of transition for supersonic flight vehicles, a wind tunnel is required with very low stream disturbance levels comparable to free flight conditions. Experimental and theoretical research to develop a low-disturbance supersonic wind tunnel has achieved a breakthrough. A new concept for nozzle design is presented which promises a large increase in the length of the quiet test core. The Advanced Mach 3.5 Axisymmetric Quiet Nozzle is the first prototype built to prove the new design concept. Experimental results from this new nozzle on the extent of laminar wall boundary layers are compared with data from other nozzles and with theoretical predictions based on linear stability theory. The Reynolds numbers based on the measured length of the quiet test core for this new nozzle are in excellent agreement with the theoretical predictions. The effect of surface finish on the nozzle performance is also discussed.

Chen, Fang-Jenq↗