Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “engineered form”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Flow visualization study in high aspect ratio cooling channels for rocket engines

The structural integrity of high pressure liquid propellant rocket engine thrust chambers is typically maintained through regenerative cooling. The coolant flows through passages formed either by constructing the chamber liner from tubes or by milling channels in a solid liner. Recently, Carlile and Quentmeyer showed life extending advantages (by lowering hot gas wall temperatures) of milling channels with larger height to width aspect ratios (AR is greater than 4) than the traditional, approximately square cross section, passages. Further, the total coolant pressure drop in the thrust chamber could also be reduced, resulting in lower turbomachinery power requirements. High aspect ratio cooling channels could offer many benefits to designers developing new high performance engines, such as the European Vulcain engine (which uses an aspect ratio up to 9). With platelet manufacturing technology, channel aspect ratios up to 15 could be formed offering potentially greater benefits. Some issues still exist with the high aspect ratio coolant channels. In a coolant passage of circular or square cross section, strong secondary vortices develop as the fluid passes through the curved throat region. These vortices mix the fluid and bring lower temperature coolant to the hot wall. Typically, the circulation enhances the heat transfer at the hot gas wall by about 40 percent over a straight channel. The effect that increasing channel aspect ratio has on the curvature heat transfer enhancement has not been sufficiently studied. If the increase in aspect ratio degrades the secondary flow, the fluid mixing will be reduced. Analysis has shown that reduced coolant mixing will result in significantly higher wall temperatures, due to thermal stratification in the coolant, thus decreasing the benefits of the high aspect ratio geometry. A better understanding of the fundamental flow phenomena in high aspect ratio channels with curvature is needed to fully evaluate the benefits of this geometry. The fluid dynamic and conjugate heat transfer problem of high aspect ratio rocket engine coolant channels are being investigated numerically, but these efforts have been hampered by a lack of validating data. Wall temperature data is available for the conjugate problem for channels without curvature and aspect ratio = 5.0, and unheated fluid dynamic data are available for square and circular cross section channels with curvature at Reynold's numbers up to 40,000. But the effects of aspect ratio on secondary flow development have not been experimentally studied. To provide some insight into the effects of channel aspect ratio on secondary flow and to qualitatively provide anchoring for the numerical codes, a flow visualization experiment was initiated at the NASA Lewis Research Center.

Meyer, Michael L.↗
NASA NTRS1993

The systems engineering overview and process (from the Systems Engineering Management Guide, 1990)

The past several decades have seen the rise of large, highly interactive systems that are on the forward edge of technology. As a result of this growth and the increased usage of digital systems (computers and software), the concept of systems engineering has gained increasing attention. Some of this attention is no doubt due to large program failures which possibly could have been avoided, or at least mitigated, through the use of systems engineering principles. The complexity of modern day weapon systems requires conscious application of systems engineering concepts to ensure producible, operable and supportable systems that satisfy mission requirements. Although many authors have traced the roots of systems engineering to earlier dates, the initial formalization of the systems engineering process for military development began to surface in the mid-1950s on the ballistic missile programs. These early ballistic missile development programs marked the emergence of engineering discipline 'specialists' which has since continued to grow. Each of these specialties not only has a need to take data from the overall development process, but also to supply data, in the form of requirements and analysis results, to the process. A number of technical instructions, military standards and specifications, and manuals were developed as a result of these development programs. In particular, MILSTD-499 was issued in 1969 to assist both government and contractor personnel in defining the systems engineering effort in support of defense acquisition programs. This standard was updated to MIL-STD499A in 1974, and formed the foundation for current application of systems engineering principles to military development programs.

Source record↗
NASA NTRS2017

Investigation of a Tricarbide Grooved Ring Fuel Element for a Nuclear Thermal Rocket

Deep space exploration, especially that of Mars, is on the horizon as the next big challenge for space exploration. Nuclear propulsion, through which high thrust and efficiency can be achieved, is a promising option for decreasing the cost and logistics of such a mission. Work on nuclear thermal engines goes back to the days of the NERVA program. Currently, nuclear thermal propulsion is under development again in various forms to provide a superior propulsion system for deep space exploration. The authors have been working to develop a concept nuclear thermal engine that uses a grooved ring fuel element as an alternative to the traditional hexagonal rod design. The authors are also studying the use of carbide fuels. The concept was developed in order to increase surface area and heat transfer to the propellant. The use of carbides would also raise the temperature limitations of the reactor. It is hoped that this could lead to a higher thrust to weight nuclear thermal engine. This paper describes the modeling of neutronics, heat transfer, and fluid dynamics of this alternative nuclear fuel element geometry. Fabrication experiments of grooved rings from carbide refractory metals are also presented along with material characterization and interactions with a hot hydrogen environment.

Taylor, Brian D.↗
NASA NTRS2018

Study of a Tricarbide Grooved Ring Fuel Element for Nuclear Thermal Propulsion

Deep space exploration, especially that of Mars, is on the horizon as the next big challenge for space exploration. Nuclear propulsion, through which high thrust and efficiency can be achieved, is a promising option for decreasing the cost and logistics of such a mission. Work on nu- clear thermal engines goes back to the days of the NERVA program. Currently, nuclear thermal propulsion is under development again in various forms to provide a superior propulsion system for deep space exploration. The authors have been working to develop a concept nuclear thermal engine that uses a grooved ring fuel element as an alternative to the traditional hexagonal rod design. The authors are also studying the use of carbide fuels. The concept was developed in order to increase surface area and heat transfer to the propellant. The use of carbides would also raise the operating temperature of the reactor. It is hoped that this could lead to a higher thrust to weight nuclear thermal engine. This paper describes the modeling of neutronics, heat transfer, and fluid dynamics of this alternative nuclear fuel element geometry. Fabrication experiments of grooved rings from carbide refractory metals are also presented along with material characterization and interactions with a hot hydrogen environment. Results of experiments and associated analysis are desired densities with some success in material distribution and reaching a solid solution. Future work is needed to improve distribution of material, minimize oxidation during the milling process, and de ne a fabrication process that will serve for constructing grooved ring fuel rods for large system tests.

Taylor, Brian↗
NASA NTRS2018

Study of a Tricarbide Grooved Ring Fuel Element for Nuclear Thermal Propulsion

Deep space exploration, especially that of Mars, is on the horizon as the next big challenge for space exploration. Nuclear propulsion, through which high thrust and efficiency can be achieved, is a promising option for decreasing the cost and logistics of such a mission. Work on nuclear thermal engines goes back to the days of the NERVA program. Currently, nuclear thermal propulsion is under development again in various forms to provide a superior propulsion system for deep space exploration. The authors have been working to develop a concept nuclear thermal engine that uses a grooved ring fuel element as an alternative to the traditional hexagonal rod design. The authors are also studying the use of carbide fuels. The concept was developed in order to increase surface area and heat transfer to the propellant. The use of carbides would also raise the operating temperature of the reactor. It is hoped that this could lead to a higher thrust to weight nuclear thermal engine. This paper describes the modeling of neutronics, heat transfer, and fluid dynamics of this alternative nuclear fuel element geometry. Fabrication experiments of grooved rings from carbide refractory metals are also presented along with material characterization and interactions with a hot hydrogen environment. Results of experiments and associated analysis are discussed. The authors demonstrated success in reaching desired densities with some success in material distribution and reaching a solid solution. Future work is needed to improve distribution of material, minimize oxidation during the milling process, and define a fabrication process that will serve for constructing grooved ring fuel rods for large system tests.

Taylor, Brian↗
DOE OSTI2020

HePHAESTUS: Heat Pipe Heterogeneous Approximation of Energy and Navier-Stokes Equations, Transience, and Non-Uniform Surface Heating [Slides]

A heat pipe is a liquid/vapor filled metal pipe capable of transporting large amounts of heat through evaporation of a liquid at one end and condensation of vapor at the other end creating a closed fluid loop. Heat pipes are widely used in the cooling of electronics and in space applications. Heat pipes are typically composed of a pipe wall, a wick material, a working fluid, and a central vapor channel. Heat is transferred into the working fluid at the “evaporator” end, through an adiabatic section, and heat is removed at the opposite end at the “condenser.” If no wick is used, gravitational acceleration can circulate the fluid due to the buoyancy of the vapor in the central core and a falling film of liquid at the pipe wall forming a “thermosyphon."

42 ENGINEERING↗
NASA NTRS1973

Experimental quiet engine program. Predicted engine performance

Three turbofan configurations, each incorporating alternative noise reduction features, were tested under the Quiet Engine Program. Performance data for these engines are shown over a range of flight conditions. The data are presented in tabular form for standard day flight inlet conditions. Procedures for estimating nonstandard day performance are shown. Tabular data and calculation procedures to allow determination of ram recovery, customer bleed, and customer shaft power extraction effects on engine performance can be found in the original Performance Brochure titled, Experimental Quiet Engine Program, Predicted Engine Performance, dated April 8, 1970. Predicted engine noise levels for representative take-off and approach conditions are provided.

Source record↗
DOE OSTI2023

Tunable doping of carbon nanotubes through engineered atomic layer deposition

A carbon nanotube field effect transistor (CNFET), that has a channel formed of carbon nanotubes (CNTs), includes a layered deposit of a nonstoichiometric doping oxide (NDO), such as HfOX, where the concentration of the NDO varies through the thickness of the layer(s). An n-type metal-oxide semiconductor (NMOS) CNFET made in this manner can achieve similar ON-current, OFF-current, and/or threshold voltage magnitudes to a corresponding p-type metal-oxide semiconductor (PMOS) CNFET. Such an NMOS and PMOS can be used to achieve a symmetric complementary metal-oxide semiconductor (CMOS) CNFET design.

Source record↗
NASA NTRS1978

Engineering handbook on the atmospheric environmental guidelines for use in wind turbine generator development

The guidelines are given in the form of design criteria relative to wind speed, wind shear, turbulence, wind direction, ice and snow loading, and other climatological parameters which include rain, hail, thermal effects, abrasive and corrosive effects, and humidity. This report is a presentation of design criteria in an engineering format which can be directly input to wind turbine generator design computations. Guidelines are also provided for developing specialized wind turbine generators or for designing wind turbine generators which are to be used in a special region of the United States.

Frost, W.↗
NASA NTRS1993

Integration of Design, Thermal, Structural, and Optical Analysis, Including Thermal Animation

In many industries there has recently been a concerted movement toward 'quality management' and the issue of how to accomplish work more efficiently. Part of this effort is focused on concurrent engineering; the idea of integrating the design and analysis processes so that they are not separate, sequential processes (often involving design rework due to analytical findings) but instead form an integrated system with smooth transfers of information. Presented herein are several specific examples of concurrent engineering methods being carried out at Langley Research Center (LaRC): integration of thermal, structural and optical analyses to predict changes in optical performance based on thermal and structural effects; integration of the CAD design process with thermal and structural analyses; and integration of analysis and presentation by animating the thermal response of a system as an active color map -- a highly effective visual indication of heat flow.

Amundsen, Ruth M.↗
DOE OSTI2026

Towards dislocation-driven quantum interconnects

A central problem in the deployment of quantum technologies is the realization of robust architectures for quantum interconnects. We propose to engineer interconnects in semiconductors and insulators by patterning spin qubits at dislocations, thus forming quasi one-dimensional lines of entangled point defects. To gain insight into the feasibility and control of dislocation-driven interconnects, we investigate the optical cycle and coherence properties of nitrogen-vacancy (NV) centers in diamond, in proximity of dislocations, using a combination of advanced first-principles calculations. We show that one can engineer spin defects with properties similar to those of their bulk counterparts, including charge stability and a favorable optical cycle, and that NV centers close to dislocations have much improved coherence properties. Finally, we predict optically detected magnetic resonance spectra that may facilitate the experimental identification of specific defect configurations. Our results provide a theoretical foundation for the engineering of one-dimensional arrays of spin defects in the solid state.

Materials science↗
NASA NTRS2011

Product Lifecycle Management and the Quest for Sustainable Space Exploration Solutions

Product Lifecycle Management (PLM) is an outcome of lean thinking to eliminate waste and increase productivity. PLM is inextricably tied to the systems engineering business philosophy, coupled with a methodology by which personnel, processes and practices, and information technology combine to form an architecture platform for product design, development, manufacturing, operations, and decommissioning. In this model, which is being implemented by the Marshall Space Flight Center (MSFC) Engineering Directorate, total lifecycle costs are important variables for critical decision-making. With the ultimate goal to deliver quality products that meet or exceed requirements on time and within budget, PLM is a powerful concept to shape everything from engineering trade studies and testing goals, to integrated vehicle operations and retirement scenarios. This briefing will demonstrate how the MSFC Engineering Directorate is implementing PLM as part of an overall strategy to deliver safe, reliable, and affordable space exploration solutions and how that strategy aligns with the Agency and Center systems engineering policies and processes. Sustainable space exploration solutions demand that all lifecycle phases be optimized, and engineering the next generation space transportation system requires a paradigm shift such that digital tools and knowledge management, which are central elements of PLM, are used consistently to maximum effect. Adopting PLM, which has been used by the aerospace and automotive industry for many years, for spacecraft applications provides a foundation for strong, disciplined systems engineering and accountable return on investment. PLM enables better solutions using fewer resources by making lifecycle considerations in an integrative decision-making process.

Caruso, Pamela W.↗
NASA NTRS2018

Theory Validation - 2 Points of View

The task of validating any given theory against any given proprotor/propeller data set is of immense importance. Not just to the researchers who are developing a theory, but to the working engineers using the theory to design a proprotor/propeller. However, there is major difference in how the two groups see validation. This difference is that, most frequently, researchers see the validation in coefficient form as, for example, CP versus CT or Figure of Merit versus CT. In contrast, design engineers are always working in the dimensional world as, for example, horsepower required to hover versus aircraft weight. The objective of the design engineer is, of course, to release drawings and specifications to manufacturing so a VTOL aircraft will be built with reasonably high assurance that the aircraft will meet the primary specifications.

Harris, Franklin D.↗
NASA NTRS2022

Analysis of Base Metal Microstructures and Mechanical Properties of a Single-Piece, Spin-Formed Forward Pressure Vessel Bulkhead

In 2012, a pathfinder forward pressure vessel bulkhead (FPVBH) for the Orion Multi-Purpose Crew Vehicle (MPCV) was fabricated using aluminum (Al) alloy 2219. The demonstration article was offered as a replacement for the baseline configuration, which at that time was a multi-piece welded construction using aluminum-lithium (Al-Li) alloy 2195. In 2014, the NASA Engineering and Safety Center (NESC) funded a Phase I effort to explore spin-forming as a manufacturing method to produce a complex-shaped, single-piece FPVBH for the crew module (CM) [1]. The primary focus of the NESC effort was to expand spin-forming technology to the fabrication of an Al-Li 2195 FPVBH. As a result, limited testing and analysis was performed on the original Al 2219 article. In this study, a sufficiently large plate of Al 2219 was not available for the fabrication of a FPVBH. Therefore, the forming blank comprised two plates (from different lots) butt welded together using a single friction stir weld. The welded forming blank was then spin formed into the FPVBH configuration and heat treated to the T62 temper. Mechanical property testing of the spin-formed 2219-T62 FPVBH revealed that the tensile properties were comparable to the Metallic Material Properties Development and Standardization (MMPDS) A-basis allowable for Al 2219-T6 wrought products. However, post-spin forming application of the standard heat treatment produced large, recrystallized grains in the material. The response varied within the two plates; one plate lot exhibited nearly complete recrystallization, while the other lot contained bands of recrystallization. Although no reduction in tensile properties was observed due to these microstructural variations, a more detailed investigation was recommended to better understand the effect of spin forming on the recrystallization mechanism and the impact on other material properties. The current study examined the microstructure and mechanical properties of the fully processed Al 2219-T62 FPVBH with emphasis on comparing differences between the two plates. Testing was limited to the cone region of the FPVBH. The two specific tasks in this study were: a) Characterization of the microstructure and mechanical properties in the two plates used in the FPVBH. b) Isolation of the impact of each step in the thermo-mechanical processing (TMP) sequence of the FPVBH on recrystallization and grain growth. Mechanical property testing sampled regions containing both large, recrystallized and small, unrecrystallized grains. Tensile strengths and elongations were equivalent in both regions and exceeded MMPDS A-basis allowables. Fracture toughness was equivalent in both regions and fracture morphology was typical of aluminum alloys. The fatigue precrack region of the fracture toughness specimens appeared more faceted in the recrystallized plate. This suggests that property testing that is more sensitive to grain size, such as fatigue crack growth rate and stress corrosion cracking, may be warranted. Alcoa reviewed the production records for the two plate lots and confirmed that composition of both plates was within the allowable range for Al 2219 and that plate processing steps were all performed within production limits. However, the Fe content was notably higher in the fully recrystallized plate, resulting in a greater volume fraction of large Fe-bearing inclusions and Al-Cu constituent particles. Alcoa did not provide details regarding plate processing variables for the two plate lots. It was surmised that deformation by hot rolling was the most accurate TMP simulation of commercial spin forming within a laboratory setting. Both hot rolling and spin forming comprise combinations of shear and compressive deformation. The through-thickness strain caused by hot rolling is symmetrical about the mid-plane, as the rollers contact both sides of the material. Shear strains are maximum at the inner and outer surfaces and trend toward zero at the mid-thickness. In contrast, spin forming utilizes a single roller on the outer surface, producing a gradient in shear stress through the thickness. Shear strains in spin-formed material are highest at the outer surface due to direct contact with the roller, and trend toward zero at the inner surface. Consequently, there will undoubtedly be some discrepancies in the mechanical response of hot-rolled and spin-formed products in the through-thickness direction. Interrupted TMP simulations were performed on remnant plate from the FPVBH forming blank in order to isolate the effects of a post-weld anneal, spin-forming deformation/thermal cycling, and solution heat treatment (SHT) on development of the recrystallized microstructures. Analysis confirmed that large, recrystallized grains formed exclusively during SHT and only after a certain deformation level was exceeded. Remnant plate from both lots that received thermal processing only did not exhibit recrystallization but exhibited fully recrystallized microstructures when processed by hot rolling. This indicates that (1) the level of deformation exceeded the critical level for recrystallization in both plates and (2) that the level of deformation during hot rolling was greater than that which accumulated during spin forming of the FPVBH. Comparison of the hot-rolled plate with the spin-formed material showed that the recrystallized grain size was larger in the FPVBH, providing further evidence that deformation levels were lower in the FPVBH. The most plausible explanation for the differing degrees of recrystallization in the two plates is particle stimulated nucleation (PSN) at the Fe-bearing inclusions and large Al-Cu constituent particles. In the plate with higher solute content, the greater volume fraction of these particles reduces the deformation level required to promote recrystallization. During spin forming the critical deformation level was likely exceeded for the higher Fe content plate resulting in a fully recrystallized microstructure. The lower Fe content plate developed a microstructure that exhibited bands of recrystallization due to the combination of a non-uniform distribution of particles and deformation. The critical deformation required for recrystallization was likely only exceeded during spin forming in regions of higher particle content. While there were differences in Fe content between these lots of Al 2219 plate, the composition of both was within defined alloy limits and Alcoa reported no anomalies during plate production. The observed differences in recrystallization after spin forming may reflect the inherent variability between these two lots of plate. The spin-forming vendor, Spincraft, reported that similar variations in recrystallized microstructures have been observed during examination of multiple spin-forming trials of a different 2xxx series aluminum alloy. Hence, tighter chemical specification limits on impurity levels in Al 2219 plate may help ensure uniform, predictable microstructures. Finally, the tensile and fracture toughness properties were not affected by the microstructural variations noted.

single-piece↗
NASA NTRS1930

Performance of a High-Speed Compression-Ignition Engine Using Multiple Orifice Fuel Injection Nozzles

This report presents test results obtained at the Langley Memorial Aeronautical Laboratory of the National Advisory Committee for Aeronautics during an investigation to determine the relative performance of a single-cylinder, high-speed, compression-ignition engine when using fuel injection valve nozzles with different numbers, sizes, and directions of round orifices. A spring-loaded, automatic injection valve was used, centrally located at the top of a vertical disk-type combustion chamber formed between horizontally opposed inlet and exhaust valves of a 5 inch by 7 inch engine.

Spanogle, J A↗
NASA NTRS1938

The Aerodynamic Characteristics of Four Full-Scale Propellers Having Different Plan Forms

Tests were made of four propellers, with diameters of 10 feet, having different blade plan forms. One propeller (Navy design no. 5868-r6) was of the usual present-day type and was used as a basis of comparison for the other three, which had unusual plan forms distinguished by the inward (toward the hub) location of the sections having the greatest blade width. It was found that propellers with points of maximum blade width occurring closer to the hub than on the present-day type of blade had higher peak efficiencies but lower take-off efficiencies. This results was found true for a "clean" liquid-cooled engine installation. It appears that some modification could be made to present plan forms which would produce propellers having more satisfactory aerodynamic qualities. The propellers with the inward location of the points of maximum blade width had lower thrust and power coefficients and stalled earlier than the present-day type.

Hartman, Edwin P↗
DOE OSTI2022

Crankcase ventilation system with dead space alignment sleeves

A cylinder aligning sleeve and adapter plate for use within an internal combustion engine. The sleeve includes apertures placed contiguously with holes within the adapter plate to form a flow passage through the dead space between compression and crosshead pistons. The flow passage exits to a vent line where gas detection may occur along with safe venting of any gas detected. The sleeve serves to ensure concentric alignment of the compression cylinder with the engine block bore.

Alvarado, Caleb A.↗
NASA NTRS1993

Review and analysis of dense linear system solver package for distributed memory machines

A dense linear system solver package recently developed at the University of Texas at Austin for distributed memory machine (e.g. Intel Paragon) has been reviewed and analyzed. The package contains about 45 software routines, some written in FORTRAN, and some in C-language, and forms the basis for parallel/distributed solutions of systems of linear equations encountered in many problems of scientific and engineering nature. The package, being studied by the Computer Applications Branch of the Analysis and Computation Division, may provide a significant computational resource for NASA scientists and engineers in parallel/distributed computing. Since the package is new and not well tested or documented, many of its underlying concepts and implementations were unclear; our task was to review, analyze, and critique the package as a step in the process that will enable scientists and engineers to apply it to the solution of their problems. All routines in the package were reviewed and analyzed. Underlying theory or concepts which exist in the form of published papers or technical reports, or memos, were either obtained from the author, or from the scientific literature; and general algorithms, explanations, examples, and critiques have been provided to explain the workings of these programs. Wherever the things were still unclear, communications were made with the developer (author), either by telephone or by electronic mail, to understand the workings of the routines. Whenever possible, tests were made to verify the concepts and logic employed in their implementations. A detailed report is being separately documented to explain the workings of these routines.

Narang, H. N.↗