SEARCH · Engineering Papers

Results for “compressed gas”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

All sources NASA NTRS DOE OSTI

DOE OSTI2022

Evaluation of a novel mid-infrared pyrometer for dynamic material experiments

Temperature is a complicated thermodynamic parameter to measure in dynamic compression experiments. Optical pyrometry is a general-purpose “work-horse” technique for measuring temperature from a radiant surface on these experimental platforms. The optical pyrometry channels are commonly held to the visible or Near-Infrared spectrum, which provides high fidelity temperature measurement for shock temperature above ∼1200–1500 K. However, low temperature (T < 1200 K) dynamic material experiments, including low pressure or quasi-isentropic studies, as well as experiments with complex thermodynamic paths, require Mid-Infrared (Mid-IR) for high fidelity measurements. This article outlines the design, testing, and characterization of a novel Mid-IR pyrometer system that can be configured between 2.5 and 5.0 µm, suitable for lower temperature measurements and for increasing the fidelity and precision of higher temperature measurements. Experimental validation was done on two separate gas gun platforms, with two separate impact velocities, achieving temperatures between 450 and 1100 K.

Dutra, E. C. (ORCID:0000000167649195)↗

DOE OSTI2023

A Miniaturized Ignition Screening Rapid Compression Machine for probing low-to-intermediate temperature chemistry

With an objective to achieve net-zero emissions by no later than 2050, biofuels hold enormous potential as sustainable, renewable fuels that can be produced on a large scale. However, fuels of a similar type, derived from limited feedstock batch can dramatically vary in terms of their chemical structures and compositions, causing significant differences in physicochemical properties mainly influencing ignition-relevant properties. Rigorous prescreening and testing efforts are involved to evaluate fuels to comply with engines equipped with advanced combustion modes. The testing of some of these fuels implies low quantity fuel samples, access to relevant temperature and pressure conditions, high reproducibility, and a high throughput rate. In light of these considerations, a Miniaturized Ignition Screening Rapid Compression Machine (MISR) has been developed and built at the University of Illinois Chicago (UIC). Some design features include a smaller bellows-actuated driver section compared to other RCM designs, an adjustable brake section, and full optical access. The setup is designed to achieve reaction conditions (T > 600K and P < 100 bar with repetition rates of about 8 seconds per experiment). These conditions are relevant to low-to-intermediate temperature auto-ignition and can generate data for developing relevant chemical kinetics models or ignition maps. A brief insight into MISR design and its operating mechanism is shown. Also, to demonstrate the performance characteristics of the MISR, Ignition Delay (I.D) experiments for ethanol fuel at different equivalence ratios (Φ) are discussed in the context of plans with additional optical diagnostics, high-speed imaging, and gas sampling experiments.

Tomar, Mukul↗

DOE OSTI2021

Thermodynamic properties of ε -Fe with thermal electronic excitation effects on vibrational spectra

The thermodynamic properties of hexagonal-close-packed iron (ε–Fe) are essential for investigating the internal structure and dynamic properties of planetary cores. Despite their importance to planetary sciences, experimental investigations of ε–Fe at relevant conditions are still challenging. Therefore, ab initio calculations are crucial to elucidating the thermodynamic properties of this system. Here, we use a free energy calculation scheme based on the phonon gas model compatible with temperature-dependent phonon frequencies. We investigate the effects of electronic thermal excitations, which introduces a temperature dependence on phonon frequencies, and the implication for the thermodynamic properties of ε–Fe at extreme pressure (P) and temperature (T) conditions. We disregard phonon-phonon interactions, i.e., anharmonicity and their effect on phonon frequencies. Nevertheless, the current scheme is also applicable to T -dependent anharmonic frequencies. We conclude that the impact of thermal electronic excitations on vibrational properties is not significant up to ~4000 K at 200 GPa but should not be ignored at higher temperatures or pressures. However, the static free energy F st must always include the effect of thermal excitation fully in a continuum of T. Furthermore, our results for isentropic equations of state show good agreement with data from recent ramp compression experiments up to 1400 GPa conducted at the National Ignition Facility.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2025

Investigating the Combustion Performance of Dual Fuel Combustion with Diesel and Port Injected Hydrogen in a Large Bore Locomotive Engine

The heavy-duty transportation sector has primarily relied on conventional diesel combustion engines given their reliability and high thermal efficiency relative to spark ignition engines, but increased focus on reducing greenhouse gas emissions has led to investigation into alternative fuels. Gaseous hydrogen fuel has garnered a great deal of recent interest in the engine community given it has zero carbon, but hydrogen is not available at the scale and cost that petroleum fuels are currently available, and this is a barrier to adoption for industries that are looking to decarbonize their operations. Because of the fuel flexibility provided, dual fuel technology offers a pathway for some industries to adopt hydrogen as a fuel source while maintaining sufficient flexibility in times and locations where the new fuel is not yet available. This computational study investigates dual fuel combustion in a large bore locomotive engine architecture using direct injected diesel and port injected gaseous hydrogen fuel. With an optimal port fuel injection configuration from previous work, simulations of varying substitution ratio, compression ratio, manifold air temperature, diesel injection timing, and diesel injection pressure were performed to understand their effect on combustion performance. Results indicated that both increased substitution ratio and higher intake air temperature accelerates hydrogen flame propagation and can result in high peak cylinder pressures. Additionally, diesel injection timing and injection pressure were demonstrated as effective methods for controlling dual fuel combustion heat release rates.

ODonnell, Patrick Christopher↗

DOE OSTI2021

Pressure Exchanger for Energy Recovery in a Trans-Critical CO2 Refrigeration System

Trans-critical CO2 vapor compression (VC) refrigeration cycles require a high compression ratio, which is associated with high expansion losses. To recover these expansion losses, a pressure exchange process between the low- and high-pressure sides of the VC cycle is proposed and examined in this study. The proposed pressure exchange system is an open type constant volume process where the high- and low-pressure flows mix inside the system. This prototype is inspired by the pressure exchangers used in reverse-osmosis (RO) desalination systems. In this system, a 2D model was generated and modeled using the computational fluid dynamics (CFD) technique. The numerical model ignored any losses due to leakage or hydraulic friction and the process is considered adiabatic. For the modeling, it was assumed that the inlet conditions for the two pressure exchanger flows are similar to the flow conditions at the evaporator and gas cooler outlets in a VC cycle. Two parameters are examined to test the validity of the system and understand their effect on the performance, including the inlet flow rate represented by the inlet velocity and the process time represented by the speed of rotation. A total of nine cases were simulated and analyzed in this study.

30 DIRECT ENERGY CONVERSION↗

DOE OSTI2023

A numerical study of an atomizing jet in a resonant acoustic field

By applying state-of-the-art, high-fidelity methods for compressible multiphase flows, this work features a parametric study of a turbulent liquid jet atomizing under the influence of standing acoustic waves with five different amplitude values. We perform these simulations in a semi-periodic domain to isolate interactions between acoustic and atomization processes and to emulate a pure liquid fuel spray placed at the pressure node of a resonant acoustic field. Characterization of the flow includes measurements of the mean dimensions, droplet number, and surface area of the liquid distribution, alongside qualitative depictions of the interface evolution, breakup events, and hydrodynamic fields. As acoustic forcing is provided to the flow, the added energy provokes atomization when shear would otherwise be insufficient for breakup. The magnitude of the forcing determines the rate of droplet production, which accelerates as the evolving liquid surface modifies the induced motion of the gas phase. At the nodal plane, the acoustic field produces an organizing effect on the liquid structures.

42 ENGINEERING↗

DOE OSTI2021

Oxidation behaviors of matrix-grade graphite during water vapor ingress accidents for high temperature gas-cooled reactors

Water ingress into cores of high temperature gas-cooled reactors (HTGRs) can cause serious safety problems in graphitic components, especially for matrix graphite, which is more vulnerable than nuclear graphite. Here in this study, oxidation behaviors of a matrix-grade graphite, ARB-B1, were investigated under simulated water ingress accidental conditions. The oxidation tests were conducted in water vapor/helium mixed atmospheres at elevated temperatures up to 1200 °C. Oxidation rates and activation energy were evaluated by mass loss measurements. The activation energy was 121.5 kJ/mol in the considered temperature range, indicating only one oxidation regime-in-pore diffusion assisted by cracks. The cracks originated from the fabrication process, acting as penetration paths for the oxidant, played an important role in the oxidation behaviors. Ungraphitized binder oxidation occurred at all temperatures, while apparent oxidation of filler particles started from 1100 °C. Moreover, oxidation effects on compressive properties and hardness of the matrix graphite were discussed in terms of oxidized microstructures. This first detailed study on matrix graphite oxidation in water vapor provides important kinetics knowledge and microstructural and mechanical data for accidental scenarios of HTGRs as well as for development of new matrix graphite materials.

36 MATERIALS SCIENCE↗

DOE OSTI2022

INVESTIGATION OF TURBULENT JETS, SPRAYS, AND SUPERCRITICAL MIXING BY TIME RESOLVED RAINBOW SCHLIEREN DEFLECTOMETRY

As technological advancements have enabled higher efficiency compression ignition (CI) engines (diesel engines) by operating at higher pressures and temperatures, the mechanisms of fuel-air mixing are postulated to change. Thus, there is a greater need for experimental data to develop and verify new phenomena. However, the fast time scales and harsh environments associated with CI engines present many experimental difficulties and requires high quality non-intrusive diagnostics to obtain useful data. The diagnostics itself must be validated prior to its implementation in an engine environment. The purpose of this research is to advance rainbow schlieren deflectometry (RSD) to study turbulent fuel sprays including the effects of supercritical mixing in CI engine environments. This objective is met by developing and applying quantitative RSD, for the first time, to three separate aspects of fuel sprays: 1) turbulent mixing, 2) phase boundaries, and 3) non-ideal gas mixing. First, quantitative RSD is demonstrated for turbulent mixing in a canonical helium jet. Rayleigh scattering data in the literature is used to validate the concentration measurements obtained by RSD. The results also provide explanations for phenomena occurring in the helium jet and provide data not yet present in the literature. Second, RSD is applied to high pressure multi-phase fuel sprays and new methodologies are developed to distinguish the liquid region from the vapor region and to quantify the in-between region on a probabilistic basis. Isolating liquid and vapor regions generally requires two separate diagnostics, e.g., Mie scattering (liquid region) and Rayleigh scattering (vapor region). However, the results of this study demonstrate that RSD can be used as a single diagnostic to measure both liquid and vapor boundaries. Third, the optical-to-thermodynamic relations associated with refrac-tometry are investigated under non-ideal gas mixing conditions to develop a generalized relationship valid for both ideal or non-ideal gas mixing. The last part of this research develops the theoretical tools to understand and experimentally realize supercritical mixing at diesel conditions. Guided by the theoretical analysis, RSD is applied to compare supercritical versus transcritical mixing at CI conditions using a constant pressure test rig. It is found that while fully supercritical mixing ers benefits in diesel engines, i.e, faster mixing times (50% higher velocities), the absence of droplets which cause high levels of particulate emissions, etc., it would be difficult to achieve in practice because of the requirements of fuels with low critical temperature and/or substantial fuel preheating.

02 PETROLEUM↗

DOE OSTI2022

Mechanical properties of zeolite-templated carbons from approximate density functional theory calculations

Zeolite-templated carbon (ZTC) is a unique porous carbonaceous material whose structure is ordered at the nanometre scale, enabling a representative periodic description at the atomistic level. Utilizing an existing, well-defined reference model for ZTCs, a structural library of varying compositions was developed by refinement using density-functional tight-binding (DFTB) potentials parameterized for materials science applications. We first determined the quantum chemical-refined structures of models with CH, CHO, CHON, CHOB, and CHOBN compositions with various degrees of heteroatom substitution. These structural models comprise the characteristic morphological features of highly porous carbon materials, such as open-blade surfaces, edges, saddles, and closed-strut formations, spanning a range of curvatures and characteristic sizes. Second, we carried out alternating compression and expansion of the CHO model unit cell to determine the lowest energy structure as well as to obtain its bulk modulus in order to demonstrate a close connection between macroscopic observations and atomic-scale structures. Further, the agreement between experimental measurements and the computational model is remarkable and demonstrates the power of approximate density functional theory as a cost-effective computational tool with chemical accuracy for the investigation of structure/property relationships in real-world carbon-based solids.

03 NATURAL GAS↗

DOE OSTI2020

Control of Weld Residual Stress in a Thin Steel Plate through Low Transformation Temperature Welding Consumables

Low transformation temperature welding (LTTW) consumables are characterized by a low martensite start temperature and a large fraction of martensite forming in the weld. It can efficiently reduce the tensile residual stress because the volume expansion associated with the martensitic transformation compensates for the thermal contraction during cooling. In this work, a LTTW wire, designated as EH200B, was created for the arc welding of advanced high-strength steel thin plates. In comparison to conventional ER70S-3 wires, this LTTW wire generated an opposite distortion pattern. Neutron diffraction measurements along the center thickness of the welded plates showed the maximum residual stress along the longitudinal direction (LD) in the weld region, and the heat-affected zone (HAZ) immediately adjacent to the weld region was reduced from ~330 MPa to below 240 MPa by using the LTTW wire. A finite element (FE) model was developed to predict the residual stress distributions of the plates welded under these two wires. The simulation results showed reasonable agreement with the volume-average neutron diffraction data. Compressive residual stress in the weld region using the LTTW wire was predicted by the FE method. Electron backscattered diffraction and x-ray diffraction measurements confirmed ~90% martensite was present in the LTTW weld. The fatigue life of DP980 steel lap joint panels using EH200B wire nearly doubled that of ER70S-3 wire. This improvement was attributed to the high strength and low LD residual stress in the weld and HAZ immediately adjacent to the weld.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Durability Optimization of CO 2 Electrolyzers for Syngas Evolution

Recently, there has been an increased interest in mitigating anthropogenic CO 2 emissions through the electrochemical conversion of CO 2 into fuels and fuel feedstocks, including hydrogen gas (H 2 ), carbon monoxide (CO), and mixtures of the two to yield syngas. Commercial applications of these systems require high catalytic selectivity for the desired products, while exhibiting operational lifetimes exceeding thousands of hours. Advancements in this field have produced systems that display high selectivity of the desired products at faradaic efficiencies exceeding 95%. Despite the advancements made in CO 2 electrolysis, system durability remains a standing challenge in the field. CO 2 electrolyzer lifetimes are often limited by carbonate fouling, catalyst degradation, detrimental flooding of electrode microporous layers and anion exchange membrane (AEM) failures. In this report, a 5 cm 2 membrane electrode assembly (MEA) device is used to investigate potential failure modes and to optimize AEM CO 2 electrolyzer operation. Key findings of this study include the importance of CO 2 flow rate, use of a thin PiperION PTFE-reinforced membrane, optimizing compression to enhance contact under 40 in-lb compression, and the effect of more compressible, commercial iridium oxide anodes on system durability.

Abouremeleh, Mohammed H. [Lawrence Berkeley Nation↗

DOE OSTI2022

Modeling of shock-induced force on an isolated particle in water and air

The prediction of force on an isolated particle, while a shock is passing over it, is an important problem in many natural and industrial applications. Although the flow monotonically changes from the pre-shock to the post-shock state, the particle's force has been observed to behave nonmonotonically with a sharp peak when the shock is located halfway across the particle. This nonmonotonic behavior is due to the unsteady nature of the compression and rarefaction waves that radiate as the shock diffracts around the particle and, therefore, cannot be predicted by a quasi-steady model. An accurate force model must account for the unsteady nature of the flow and the sharp discontinues in the flow properties across the shock. In this work, we test four different inviscid models and observe that the compressible Maxey–Riley–Gatignol (C-MRG) model is the most accurate based on comparison with results from particle-resolved inviscid simulations at two different Mach numbers for both water and air as the medium. The C-MRG model is first demonstrated to predict the force on a stationary particle accurately and then extended to capture the force on a moving particle. Numerical complexities regarding the implementation of the C-MRG model are also discussed.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2022

A Novel Process for Converting Coal to High-Value Polyurethane Products

Battelle has demonstrated a patented process for making high-value, polyurethane (PU) foam from coal, based on preparing liquefied coal via direct liquefaction, converting it to polyols as an intermediate via ozonation, and then making PU foams from these polyols. This process represents a breakthrough in innovative utilization of U.S. coals, and is applicable to bituminous as well as sub-bituminous coals. The resulting PU foam products are projected to have an extremely high value (i.e., over $\$5,000$ /ton), with nearly 100% of carbon utilization from coalderived liquid feedstock, and 31.5% to 43.5% of the carbon in the PU foam polyol product being bio-based. The targeted products represent an extremely large (i.e., over $80 billion/year), existing PU foam market, which could expand into making coatings and adhesives. The process can further help reduce petroleum imports, while improving the economics of PU foam production. This work was completed with funding from the National Energy Technology Laboratory (NETL), with cost share from the State of Ohio’s Ohio Development Services Agency (ODSA) and others, and has advanced the process to 10 kg/day continuous scale and thus to Technology Readiness Level (TRL) 5. A total of 48 coal-based polyols were prepared and evaluated. The initial 28 polyols focused on range finding for ideal conditions. The later 20 polyols were produced as part of process optimizations. These optimizations were targeted around a continuous ozonolysis process to evaluate extended time reactions and to create the necessary intermediate for production of 1-gallon samples of polyol. The most unique attribute of Battelle’s polyol is in the utilization of coal’s aromaticity to gain final foam rigidity. Typically, polyols depend on the isocyanate fraction and cross-linking to gain rigidity. By utilizing coal, we were able to maintain rigidity while reducing the overall hydroxyl value of the polyol. This is important as lower hydroxyl value leads to greater percent weight of the coal-based polyol because less isocyanate is required for foaming. This leads to greater foam cost savings. This report provides the details, process, and process cost models of the conversion of coal to polyols and further to PU foams. Battelle’s process begins with coal liquids. These liquids can be obtained by two processes: coal coking or pyrolysis to produce coal tar, and Battelle’s biobased coal-to-liquids (CTL) process to produce heavy syncrude after liquifying >85% coal. After liquification, Battelle utilizes ozonolysis to create functionalization on the polyaromatic coal structure. The functionalization is then converted to the final polyester polyol through transesterification, or to hydroxyamide polyol through amidification. Equivalent or better standard properties have been obtained for 2 lb/ft 3 density rigid, water and freon-alternative blown foams, including compressive strength, density, R-value, and dimensional stability. Target applications for these foams are insulation, packaging, and energy-absorbing foams. Some exploratory testing also showed promise for adhesives applications. A detailed economic analysis showed that Battelle’s polyol process is economical, at a 140 metric tons per day (MTD) polyol production scale. An attractive return on investment (ROI) at competitive pricing validates the process is ready for a pilot-plant demonstration. A scale-up plan is provided.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2025

Evaluating Chemical Kinetics Predictions for Propane Using 3-D and 0-D Models in a Boosted Spark-Ignited Engine

Propane has been shown to be a promising alternative fuel to reduce emissions while simultaneously achieving high efficiencies in medium- and heavy-duty engines. These high-power density applications require boosted engines which, combined with high compression ratio, can lead to auto-ignition and knock. While three-dimensional (3-D) computational fluid dynamics (CFD) models are often used for resolving the complex fluid flow in engines, these models can become computationally expensive when simulating detailed chemical kinetics. Likewise, zero-dimensional (0-D) models are computationally concise enough for kinetics development, but lack any flow-field information which governs the flame propagation processes in spark ignition (SI) engines. This work presents a comprehensive comparison between 3-D and 0-D closed cycle simulations at knocking conditions in a high compression ratio high stroke-to-bore ratio propane engine. In order to initialize the flow-field for the 3-D closed cycle (intake valve closing, (IVC) to exhaust valve opening, (EVO)) simulation, a motored multi-cycle 3-D model was run using Converge to create a map at IVC, reducing the computational time. The map allowed a non-homogeneous 3-D closed cycle simulation to be satisfactorily validated against experiments, while a homogeneous case using only the turbulence field mapping was also simulated, mimicking 0-D modeling. The 3-D simulations were used to prescribe the initial conditions (e.g., IVC thermodynamics, speciation, burn-rate profile) for a 2-zone 0-D SI engine model in Chemkin Pro for both cases. It was found that 2-zone 0-D modeling underpredicted the knock onset timing, likely due to the lack of thermal stratification in the unburned gas region. Future work will carry multi-zone 0-D modeling to capture the fuel auto-ignition in the unburned region.

Douvry-Rabjeau, Julien [Oakland University, Roches↗

DOE OSTI2020

TAILORED BIOBLENDSTOCKS WITH LOW ENVIRONMENTAL IMPACT TO OPTIMIZE MCCI ENGINES

The overall objective of the project is to develop and demonstrate a microalgae bio-blendstock with greater than 60% greenhouse gas reduction potential relative to petroleum diesel, that can reduce sooting propensity, increase cetane number and improve engine thermal efficiency relative to a baseline diesel engine operating on conventional fuel. Specific objectives include: (1) development of a new framework for both LCA and TEA that explicitly considers temporal variation in productivity and the frequency of crop loss; (2) determination of how fuel compounds that can be produced from the algal biomass can be ‘bio-tailored’ based on the species composition and biological production process, and subsequent processing via HTL to biocrude, and upgrading of the biocrude; (3) execution of a feedback loop (algae production  biocrude refining  combustion optimization  feedback to refining stage), for optimization of fuels for MCCI combustion; (4) optimization of MCCI combustion and emissions performance, accounting first for the biological processes that dictate the chemical composition of biocrude oil, and second for the subsequent chemical processes that comprise mixing controlled compression ignition combustion; (6) simulation of MCCI engine combustion processes to demonstrate the incorporation of relevant fuel chemistry that captures the specific impacts of optimized algal fuels.

09 BIOMASS FUELS↗

DOE OSTI2020

Tailored Bioblendstocks with Low Environmental Impact to Optimize MCCI Engines

09 BIOMASS FUELS↗

DOE OSTI2024

Overview of ASDEX upgrade results in view of ITER and DEMO

Experiments on ASDEX Upgrade (AUG) in 2021 and 2022 have addressed a number of critical issues for ITER and EU DEMO. A major objective of the AUG programme is to shed light on the underlying physics of confinement, stability, and plasma exhaust in order to allow reliable extrapolation of results obtained on present day machines to these reactor-grade devices. Concerning pedestal physics, the mitigation of edge localised modes (ELMs) using resonant magnetic perturbations (RMPs) was found to be consistent with a reduction of the linear peeling-ballooning stability threshold due to the helical deformation of the plasma. Conversely, ELM suppression by RMPs is ascribed to an increased pedestal transport that keeps the plasma away from this boundary. Candidates for this increased transport are locally enhanced turbulence and a locked magnetic island in the pedestal. The enhanced D-alpha (EDA) and quasi-continuous exhaust (QCE) regimes have been established as promising ELM-free scenarios. Here, the pressure gradient at the foot of the H-mode pedestal is reduced by a quasi-coherent mode, consistent with violation of the high-n ballooning mode stability limit there. This is suggestive that the EDA and QCE regimes have a common underlying physics origin. In the area of transport physics, full radius models for both L- and H-modes have been developed. These models predict energy confinement in AUG better than the commonly used global scaling laws, representing a large step towards the goal of predictive capability. A new momentum transport analysis framework has been developed that provides access to the intrinsic torque in the plasma core. In the field of exhaust, the X-Point Radiator (XPR), a cold and dense plasma region on closed flux surfaces close to the X-point, was described by an analytical model that provides an understanding of its formation as well as its stability, i.e., the conditions under which it transitions into a deleterious MARFE with the potential to result in a disruptive termination. With the XPR close to the divertor target, a new detached divertor concept, the compact radiative divertor, was developed. Here, the exhaust power is radiated before reaching the target, allowing close proximity of the X-point to the target. No limitations by the shallow field line angle due to the large flux expansion were observed, and sufficient compression of neutral density was demonstrated. With respect to the pumping of non-recycling impurities, the divertor enrichment was found to mainly depend on the ionisation energy of the impurity under consideration. In the area of MHD physics, analysis of the hot plasma core motion in sawtooth crashes showed good agreement with nonlinear 2-fluid simulations. This indicates that the fast reconnection observed in these events is adequately described including the pressure gradient and the electron inertia in the parallel Ohm’s law. Concerning disruption physics, a shattered pellet injection system was installed in collaboration with the ITER International Organisation. Thanks to the ability to vary the shard size distribution independently of the injection velocity, as well as its impurity admixture, it was possible to tailor the current quench rate, which is an important requirement for future large devices such as ITER. Progress was also made modelling the force reduction of VDEs induced by massive gas injection on AUG. The H-mode density limit was characterised in terms of safe operational space with a newly developed active feedback control method that allowed the stability boundary to be probed several times within a single discharge without inducing a disruptive termination. Regarding integrated operation scenarios, the role of density peaking in the confinement of the ITER baseline scenario (high plasma current) was clarified. The usual energy confinement scaling ITER98(p,y) does not capture this effect, but the more recent H20 scaling does, highlighting again the importance of developing adequate physics based models. Advanced tokamak scenarios, aiming at large non-inductive current fraction due to non-standard profiles of the safety factor in combination with high normalised plasma pressure were studied with a focus on their access conditions. A method to guide the approach of the targeted safety factor profiles was developed, and the conditions for achieving good confinement were clarified. Based on this, two types of advanced scenarios (‘hybrid’ and ‘elevated’

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Mining Air for Fuels and Fine Chemicals

The Intergovernmental Panel on Climate Change’s 2021 report underscores that Direct Air Capture (DAC) is an essential component to limiting global warming to 2 °C, yet separating CO 2 from air and its subsequent concentration for conversion into carbon neutral fuels/chemicals or permanent storage remains energy intensive and costly. Further, most DAC technologies rely on repetitive capture and release cycles that reduces the amount of time the DAC materials are able to collect CO 2 and increases wear and tear. Moisture swing (MS) sorption within anion exchange materials utilizes differences in relative humidity to capture and concentrate CO 2 up to 500-fold with negligible energy inputs and low-cost sorbents. Molecular modeling predicts that membranes with a dry and wet side would actively transport CO 2 from its dry side to its wet side against a counter flow of H 2 O evaporating on the dry side, however, existing MS materials are too brittle to be processed into membranes to test this hypothesis. This project brought together experts in DAC materials and design, techno-economic analysis and project management at Arizona State University (ASU), polymer processing at University of Texas at Austin (UTA) and modeling gas transport and exchange at Norther Arizona University (NAU) to develop hollow fiber membranes that use energy from water evaporation to continuously pump CO 2 from air against a concentration gradient to the membranes interior and requiring significantly less energy than current DAC technologies. While this project did not meet its ultimate objectives of demonstrating an active CO 2 pumping membrane, a number of key accomplishments were made in developing low-cost, flexible anion exchange membranes (AEM) at 3.5 m 2 scale, characterizing the ionic and molecular transport within MS materials, and developing several analytical and mathematical models of the MS and pumping process leading to new fundamental knowledge about key rate limiting steps of CO 2 flux in anion exchange membranes at low water activity. Technoeconomic models show that if CO 2 fluxes ≥ 25 µmol CO 2 m -2 s -1 (membrane surface area) are achieved that cost ≤ $\$$100/tonne CO 2 captured, purified and compressed to pipeline quality is possible. The knowledge gained in this research will guide future research in developing new materials toward overcoming these rate limiting steps that in turn could enable transformative and disruptive DAC technologies needed for capturing gigatons of CO 2 per year needed to limiting global warming to 2 °C.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗