Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “attack modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Flight investigation of the effect of tail configuration on stall, spin, and recovery characteristics of a low-wing general aviation research airplane

Flight tests were performed to investigate the stall, spin, and recovery characteristics of a low-wing, single-engine, light airplane with four interchangeable tail configurations. The four tail configurations were evaluated for effects of varying mass distribution, center-of-gravity position, and control inputs. The airplane tended to roll-off at the stall. Variations in tail configuration produced spins ranging from 40 deg to 60 deg angle of attack and turn rates of about 145 to 208 deg/sec. Some unrecoverable flat spins were encountered which required use of the airplane spin chute for recovery. For recoverable spins, antispin rudder followed by forward wheel with ailerons centered provided the quickest spin recovery. The moderate spin modes agreed very well with those predicted from spin-tunnel model tests, however, the flat spin was at a lower angle of attack and a slower rotation rate than indicated by the model tests.

Stough, H. Paul, III↗
NASA NTRS1976

A mathematical simulation model of a 1985-era tilt-rotor passenger aircraft

A mathematical model for use in real-time piloted simulation of a 1985-era tilt rotor passenger aircraft is presented. The model comprises the basic six degrees-of-freedom equations of motion, and a large angle of attack representation of the airframe and rotor aerodynamics, together with equations and functions used to model turbine engine performance, aircraft control system and stability augmentation system. A complete derivation of the primary equations is given together with a description of the modeling techniques used. Data for the model is included in an appendix.

Mcveigh, M. A.↗
NASA NTRS2015

Uncertainty Quantification of Turbulence Model Closure Coefficients for Transonic Wall-Bounded Flows

The goal of this work was to quantify the uncertainty and sensitivity of commonly used turbulence models in Reynolds-Averaged Navier-Stokes codes due to uncertainty in the values of closure coefficients for transonic, wall-bounded flows and to rank the contribution of each coefficient to uncertainty in various output flow quantities of interest. Specifically, uncertainty quantification of turbulence model closure coefficients was performed for transonic flow over an axisymmetric bump at zero degrees angle of attack and the RAE 2822 transonic airfoil at a lift coefficient of 0.744. Three turbulence models were considered: the Spalart-Allmaras Model, Wilcox (2006) k-w Model, and the Menter Shear-Stress Trans- port Model. The FUN3D code developed by NASA Langley Research Center was used as the flow solver. The uncertainty quantification analysis employed stochastic expansions based on non-intrusive polynomial chaos as an efficient means of uncertainty propagation. Several integrated and point-quantities are considered as uncertain outputs for both CFD problems. All closure coefficients were treated as epistemic uncertain variables represented with intervals. Sobol indices were used to rank the relative contributions of each closure coefficient to the total uncertainty in the output quantities of interest. This study identified a number of closure coefficients for each turbulence model for which more information will reduce the amount of uncertainty in the output significantly for transonic, wall-bounded flows.

Schaefer, John↗
NASA NTRS1987

Computational study of wind-tunnel wall effects on flow field around delta wings

This paper addresses wind-tunnel wall effects on delta-wing flow fields using the Free Vortex Sheet (FVS) theory in support of planned subsonic wind-tunnel tests. The configurations include several sizes of a 65-deg delta wing in the NASA Langley Research Center Low-Turbulence Pressure Tunnel (LTPT), and an aspect ratio 1 delta wing in the Delft University low-speed tunnel. Standard upflow correction methodology is extended to account for angle-of-attack and nonplanar effects. Blockage and streamline curvature corrections are not applied in the present investigation. Resulting corrections to the 65-deg delta flow field were good for model-to-tunnel span ratios up to 0.5 and angles of attack up to 30-deg, both for linear attached flow and nonlinear vortex flow. For the aspect ratio 1 delta wing, corrections to the vortex flow field for the effect of the averaged upflow angle were satisfactory but streamline curvature effects were larger.

Frink, Neal T.↗
NASA NTRS1972

Effect of configuration modification on the hypersonic aerodynamic characteristics of a blended delta wing-body entry vehicle

The longitudinal, lateral, and directional aerodynamic characteristics of a delta-wing configuration were obtained experimentally at Mach 20 in helium with Reynolds numbers, based on model length, of 1.5 million and 2.9 million and at a Mach number of 6 in air with a Reynolds number, based on model length, of 4.8 million. The angles of attack varied from 0 deg to 55 deg for two sideslip angles. The effects of the addition of dorsal fins, the removal of wing tip fins, an increase in elevon span, and changes in elevon hinge-line sweep angle are discussed. The unmodified vehicle had a maximum lift-drag ratio of 2.1 at Mach 19 and of 2.4 at Mach 6 with about the same lateral and directional stability level at both Mach numbers. As the Mach number increased from 6 to 20, the longitudinal center of pressure moved forward and more positive elevon deflection was therefore required to maintain a given trim angle. The removal of wing tip fins increased the maximum lift-drag ratio and had a negligible effect on longitudinal stability, but caused directional instability that was not corrected by the dorsal fins examined. The shape of the wing and elevon hinge-line sweep had a large influence on the induced yawing moment due to roll control.

Arrington, J. P.↗
NASA NTRS1974

Results of investigations on an 0.015-scale configuration 140A/B space shuttle vehicle orbiter model (49-0) in the NASA/Langley Research Center 8-foot transonic pressure tunnel (OA25)

Aerodynamic force and moment tests were conducted on an 0.015-scale space shuttle vehicle configuration 140A/B model (49-0) in a transonic pressure tunnel. The test was carried out at Mach numbers 0.35, 0.60, 0.80, 0.90, 0.98, and 1.20, and at Reynolds numbers ranging from 1.90 million per foot to 3.97 million per foot, depending on tunnel total pressure capability and model structural limits. The model attitude was varied in angle-of-attack from minus 2 deg to +22 deg at 0 deg and 5 deg angles of yaw, and in angle-of-sidelip from minus 5 to +10 deg at 0 deg, 7.5 deg, and 15 deg angles of pitch. The purpose of this test was to establish and verify longitudinal and lateral-directional characteristics of the 140A/B Configuration Orbiter and to determine the effects of surface deflections on vehicle performance, stability, and control.

Nichols, M. E.↗
NASA NTRS1976

Static force tests of a sharp leading edge delta-wing model at ambient and cryogenic temperatures with a description of the apparatus employed

A sharp leading edge delta-wing model was tested through an angle-of-attack range at Mach numbers of 0.75, 0.80, and 0.85 at both ambient and cryogenic temperatures in the Langley 1/3-meter transonic cryogenic tunnel. Total pressure was varied with total temperature in order to hold test Reynolds number constant at a given Mach number. Agreement between the aerodynamic data obtained at ambient and cryogenic temperatures indicates that flows with leading-edge vortex effects are duplicated properly at cryogenic temperatures. The test results demonstrate that accurate aerodynamic data can be obtained by using conventional force-testing techniques if suitable measures are taken to minimize temperature gradients across the balance and to keep the balance at ambient (warm) temperatures during cryogenic operation of the tunnel.

Kilgore, R. A.↗
NASA NTRS1977

Wind-tunnel tests of wide-chord teetering rotors with and without outboard flapping hinges

Wind tunnel tests of aeroelastically designed helicopter rotor models were conducted to obtain rotor aerodynamic performance and dynamic response data pertaining to two-bladed teetering rotors with a wider chord and lower hover tip speed than currently employed on production helicopters. The effects of a flapping hinge at 62 percent radius were also studied. Finally, the effects of changing tip mass on operating characteristics of the rotor with the outboard flapping hinge were examined. The models were tested at several shaft angles of attack for five advance ratios, 0.15, 0.25, 0.35, 0.40, and 0.45. For each combination of shaft angle and advance ratio, the rotor lift was varied over a wide range to include simulated maneuver conditions. At each test condition, rotor aerodynamic performance and dynamic response data were obtained. From these tests, it was found that wide-chord rotors may be subject to large control forces. An outboard flapping hinge may be used to reduce beamwise bending moments over a significant part of the blade radius without significantly affecting the chordwise bending moments.

Weller, W. H.↗
NASA NTRS1977

Effects of deflected thrust on the longitudinal aerodynamic characteristics of a close-coupled wing-canard configuration

The effects of power on the longitudinal aerodynamic characteristics of a close-coupled wing-canard fighter configuration with partial-span rectangular nozzles at the trailing edge of the wing were investigated. Data were obtained on a basic wing-strake configuration for nozzle and flap deflections from 0 deg to 30 deg and for nominal thrust coefficients from 0 to 0.30. The model was tested over an angle-of-attack range from -2 deg to 40 deg at Mach numbers of 0.15 and 0.18. Results show substantial improvements in lift-curve slope, in maximum lift, and in drag-due-to-lift efficiency when the canard and strakes have been added to the basic wing-fuselage (wing-alone) configuration. Addition of power increased both lift-curve slope and maximum lift, improved longitudinal stability, and reduced drag due to lift on both the wing-canard and wing-canard-strake configurations. These beneficial effects are primarily derived from boundary-layer control due to moderate thrust coefficients which delay flow separation on the nozzle and inboard portion of the wing flaps.

Yip, L. P.↗
NASA NTRS1978

Propeller slipstream wing interactions at Mach no. 0.8

Configuration and results of a wind tunnel test of the aerodynamic interactions between propeller slipstream and a supercritical wing at transonic Mach numbers are discussed. The test was conducted over a free-stream Mach number range from 0.7 to 0.84, with the slipstream simulator and the wing-body model installed in the tunnel. The angle of attack and the spanning lift coefficients were varied from 1 to 3 deg and from 0.4 to 0.7 deg respectively, while the slipstream swirl angle was varied from 0 to 11 deg with an upwash on the inboard side of the wing. It was found that at a free-stream Mach number of 0.8 and a lift coefficient of 0.5, incremental drag results for 7 deg of swirl and a slipstream Mach number of 0.87 indicated a penalty equivalent to a 0.024 loss in propeller efficiency, whereas at 11 deg the drag increment was favorable. Swirl had significant effects on the chordwise pressure distributions of the inboard section of the wing within the slipstream. Neither surface nor wake pressures showed signs of significant flow separation induced by the slipstream.

Bencze, D. P.↗
NASA NTRS1982

Forestry timber typing. Tanana demonstration project, Alaska ASVT

The feasibility of using LANDSAT digital data in conjunction with topographic data to delineate commercial forests by stand size and crown closure in the Tanana River basin of Alaska was tested. A modified clustering approach using two LANDSAT dates to generate an initial forest type classification was then refined with topographic data. To further demonstrate the ability of remotely sensed data in a fire protection planning framework, the timber type data were subsequently integrated with terrain information to generate a fire hazard map of the study area. This map provides valuable assistance in initial attack planning, determining equipment accessibility, and fire growth modeling. The resulting data sets were incorporated into the Alaska Department of Natural Resources geographic information system for subsequent utilization.

Morrissey, L. A.↗
NASA NTRS1986

Exploratory wind-tunnel investigation of the stability and control characteristics of advanced general aviation configurations

Results of low-speed wind-tunnel investigations are presented for two general aviation configurations: the AVTEK canard configuration and the DeVore conventional configuration. Cooperative research programs were undertaken by industry and NASA to jointly conduct tests in the NASA Langley 12-Foot Low-Speed Wind Tunnel to explore stability and control characteristics of each configuration. A 1/5-scale AVTEK model and a 1/6-scale DeVore model were tested over an angle-of-attack range of up to 45 deg and an angle-of-sideslip range of up to 20 deg. Results from the AVTEK test are presented with an emphasis on the effects of configuration on the stall and poststall characteristics. Results from the DeVore test are presented with emphasis on the effects of wing leading-edge droop design on spin resistance characteristics.

Yip, L. P.↗
NASA NTRS1986

Tactical missile aerodynamics

The present conference on tactical missile aerodynamics discusses autopilot-related aerodynamic design considerations, flow visualization methods' role in the study of high angle-of-attack aerodynamics, low aspect ratio wing behavior at high angle-of-attack, supersonic airbreathing propulsion system inlet design, missile bodies with noncircular cross section and bank-to-turn maneuvering capabilities, 'waverider' supersonic cruise missile concepts and design methods, asymmetric vortex sheding phenomena from bodies-of-revolution, and swept shock wave/boundary layer interaction phenomena. Also discussed are the assessment of aerodynamic drag in tactical missiles, the analysis of supersonic missile aerodynamic heating, the 'equivalent angle-of-attack' concept for engineering analysis, the vortex cloud model for body vortex shedding and tracking, paneling methods with vorticity effects and corrections for nonlinear compressibility, the application of supersonic full potential method to missile bodies, Euler space marching methods for missiles, three-dimensional missile boundary layers, and an analysis of exhaust plumes and their interaction with missile airframes.

Hemsch, Michael J.↗
NASA NTRS1991

F/A-18 1/9th scale model tail buffet measurements

Wind tunnel tests were carried out on a 1/9th scale model of the F/A-18 at high angles of attack to investigate the characteristics of tail buffet due to bursting of the wing leading edge extension (LEX) vortices. The tests were carried out at the Aeronautical Research Laboratory low-speed wind tunnel facility and form part of a collaborative activity with NASA Ames Research Center, organized by The Technical Cooperative Program (TTCP). Information from the program will be used in the planning of similar collaborative tests, to be carried out at NASA Ames, on a full-scale aircraft. The program covered the measurement of unsteady pressures and fin vibration for cases with and without the wing LEX fences fitted. Fourier transform methods were used to analyze the unsteady data, and information on the spatial and temporal content of the vortex burst pressure field was obtained. Flow visualization of the vortex behavior was carried out using smoke and a laser light sheet technique.

Martin, C. A.↗
NASA NTRS1991

Optimal input design for aircraft instrumentation systematic error estimation

A new technique for designing optimal flight test inputs for accurate estimation of instrumentation systematic errors was developed and demonstrated. A simulation model of the F-18 High Angle of Attack Research Vehicle (HARV) aircraft was used to evaluate the effectiveness of the optimal input compared to input recorded during flight test. Instrumentation systematic error parameter estimates and their standard errors were compared. It was found that the optimal input design improved error parameter estimates and their accuracies for a fixed time input design. Pilot acceptability of the optimal input design was demonstrated using a six degree-of-freedom fixed base piloted simulation of the F-18 HARV. The technique described in this work provides a practical, optimal procedure for designing inputs for data compatibility experiments.

Morelli, Eugene A.↗
NASA NTRS1992

Helium bubble flow visualization of the spanwise separation on a NACA 0012 with simulated glaze ice

Research was performed to experimentally visualize and document the flow separation due to simulated glaze ice accretion on a NACA 0012 semispan with 30 deg sweep using helium bubbles as flow tracers. Results are compared to Navier-Stokes computational simulations for different angles of attack. Prior to acquiring data for the semispan model, a two dimensional experiment was conducted to determine the accuracy of using the helium bubbles as flow tracers. Results from the three dimensional experiment compare well to the computational simulations.

Kerho, M.↗