Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “W”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Nondestructive evaluation techniques for nickel-cadmium aerospace battery cells

The ac impedance characteristics of Ni-Cd cells as an in-situ, nondestructive means of determining cell lifetime, particularly with respect to the probability of premature failure were evaluated. Emphasis was on evaluating Ni-Cd cell impedance over a wide frequency range (10,000 to 0.0004 Hz) as the cells were subjected to charge/discharge cycle testing. The results indicate that cell degradation is reflected in the low frequency (Warburg) impedance characteristics associated with diffusion processes. The Warburg slope (W) was found to steadily increase as a function of cell aging for completely discharged cells. In addition, based on data for two cells, a high or rapidly increasing value for W signals imminent cell failure by one mechanism. Degradation by another mechanism is apparently reflected in a fall-off (roll-over) of W at lower frequencies. As a secondary result, the frequency dependence of the absolute cell impedance at low frequencies (5 - 500 mHz) was found to be a good indication of the cell state-of-charge.

Haak, R.↗
NASA NTRS1983

The oxidation behavior of a model molybdenum/tungsten-containing alloy in air alone and in air with trace levels of NaCl(g)

Thermogravimetric, metallographic, and X-ray studies of a model alloy, Ni-(17 a/o)Al-(10 a/o)Mo+W, oxidized in dry air at 600-1200 C and in air with 10 ppm NaCl gas at 900 C, are reported. The alloy was melted under Ar and pretreated in flowing H2 for 24 h at 1300 C. Polished 1.3 x 1.3 x 0.2-cm specimens were washed and degreased prior to oxidation in a quartz tube within a furnace for up to 120 hr. The oxidation activation energy of the alloy is determined to be about 30 kcal/mole. The specimens oxidized at 900 C and hotter exhibited oxidized and nitrided phases covered by complex NiMoO4, NiWO4, and NiAl2O4 scales and a porous, nonprotective outer layer of NiO. The oxidation behavior is found to be determined by the formation and growth of the scale, especially the (Mo,W)O2 component. Al2O3 scale layers were not formed, and further runs with pure O2 or Ar-(20 percent)O2 ruled out an explanation of this phenomenon based on aluminum nitride formation. The oxidation was accelerated by the addition of NaCl gas, a finding attributed to the reaction of NaCl with external locally protective Al2O3 scales and with the internal(Mo, W)O2 layers.

Smeggil, J. G.↗
NASA NTRS1983

Experimental investigations of trace element fractionation in iron meteorites. II - The influence of sulfur

The partitioning of Ir, Ge, Ga, W, Cr, Au, P, and Ni between solid metal and metallic liquid is investigated as a function of temperature and the S-concentration of the metallic liquid. The partition coefficients for siderophile elements, such as Ir, W, Ga, and Ge, are found to increase by factors of 10-100 as the S-concentration of the metallic liquid increases from 0-30 wt percent. Partition coefficients for other siderophile elements, such as Ni, Au, and P, increase by factors of only 2-3. In contrast, a decrease is seen in the partition coefficients for the more chalcophile element Cr. These experimentally determined coefficients are used in conjunction with a fractional crystallization model to reproduce the geochemical behavior of Ni, P, Au, and Ir during the magmatic evolution of groups IIAB, IIIAB, IVA and IVB iron meteorites. The mean S-concentration for each group increases in the order IVB, IVA, IIIAB, IIAB, which is in accordance with cosmochemical prediction. However, the geochemical behavior of Ge, Ga, W, and Cr cannot be reproduced in an internally consistent way. It is concluded that the magmatic histories of these iron meteorite groups are more complex than has been generally assumed.

Jones, J. H.↗
NASA NTRS1983

A 20-GHz IMPATT transmitter, summary

A three stage IMPATT diode amplifier capable of a 16 W CW output and a 2 dB bandwidth of 117 MHz was developed. On the component side, high performance circulators with a 0.2 dB insertion loss and bandwidth of 5 GHz were fabricated. State of the art GaAs IMPATT diodes incorporating diamond heat sink and double Read doping profile were also developed. The diodes are capable of a 2.5 W CW output. A few diodes achieved power outputs as high as 3 W. On the circuit side, high gain (up to 12 dB per stage) single diode, multituned circuits capable of 2 GHz and 930 MHx bandwidth were developed as the first and second stages, respectively, of the amplifier. A 12 diode waveguide cavity combiner was developed as the output stage. The output stage utilized commercially available single drift GaAs IMPATT diodes.

Source record↗
NASA NTRS1984

Influence of composition on the microstructure and mechanical properties of a nickel-base superalloy single crystal

The effects of cobalt, tantalum, and tungsten contents on the microstructure and mechanical properties of single crystal Mar-M247 were investigated. Elevated temperature tensile and creep-rupture properties of 001 oriented single crystals were related to microstructural features of the alloys. Substitution of Ni for Co in the high refractory metal alloys increased the lattice mismatch, which was considered to be the cause of the increases in tensile and creep strength. Substitution of Ni for Ta caused large decreases in tensile strength and creep life, consistent with decreases in gamma prime volume fraction, lattice mismatch, and solid solution hardening. Substitution of W for Ta resulted in decreased life at high stresses, which was related to small decreases in mismatch and volume fraction. However, the W substitution resulted in improved life at low stresses, which was related to solid solution strengthening by W.

Nathal, M. V.↗
NASA NTRS1984

Influence of cobalt, tantaum and tungsten on the high temperature mechanical properties of single crystal nickel-base superalloys

For alloys with the baseline refractory metal level of 3 percent Ta and 10 percent W, decreases in Co level from 10 to 0 percent resulted in increased tensile strength and creep resistance. Substitution of W for Ta resulted in decreased creep life at high stresses but improved life at low stresses. Substitution of Ni for Ta caused large reductions in tensile strength and creep resistance, and corresponding increases in ductility. For these alloys with low Ta plus W totals, strength was independent of Co level. The increases in tensile strength with increases in refractory metal content were related to the increases in gamma volume fraction and solid solution hardening. Increases in strength as Co level decreased were considered to be the result of coherency strain hardening from the increased lattice mismatch. Dislocation shear through the gamma-gamma interface is considered to be the rate limiting step in the deformation process.

Nathal, M. V.↗
NASA NTRS1984

The geology of Thaumasia-northeast quadrant

The northeastern section of Thaumasia is located in the heavily cratered southern highlands of Mars between 30 S and 47.5 S and 67.5 W and 90 W. To the northwest lies the Tharis bulge and to the southeast is the Argyre Basin. Previous mapping in Thaumasia included a geologic map of the entire guadrangel by McGill (1978) at a 1:5,000,000 scale and a map of lava flows in the northwest quadrant by Scott and Tanaka (1981). Most investigations concentrated west of 90 W long. in conjunction with the Tharis volcanics. This investigation was designed to examine the overall geology of this section of Thaumasia. After distinguishing various geomorphical units, a geologic map was made at a scale of 1:2,000,000. Lastly, a general sequence of events was developed for the area. Mapping was done from individual low, medium, and high resolution images from the Viking missions, as well as using a 1:2,000,000 scale photo mosaic of the northeast quadrant of Thaumasia. Amount of cratering and faulting, superposition, differences in morphology, and albedo were used to separate out geomorphologically distinct units.

Tuesink, M. F.↗
NASA NTRS1984

The variability of the surface wind field in the equatorial Pacific Ocean: Criteria for satellite measurements

The natural variability of the equatorial Pacific surface wind field is described from long period surface wind measurements made at three sites along the equator (95 deg W, 109 deg 30 W, 152 deg 30 W). The data were obtained from surface buoys moored in the deep ocean far from islands or land, and provide criteria to adequately sample the tropical Pacific winds from satellites.

Halpern, D.↗
NASA NTRS1984

Hypothesis on the origin of lineaments in the LANDSAT and SLAR images of precambrian soil in the low Contas River Valley (southern Bahia)

Examination of LANDSAT and SLAR images in southern Bahia reveals numerous linear features, which are grouped in five sets, based on their trends: N65 degrees E, N70 degrees W, N45 degrees E and NS/N15 degrees E. Owing to their topographic expressions, distributive patterns, spacing between individual lineaments and their mutual relationships, the lineament sets of N65 degrees E and N70 degrees W, as well as the sets of N40 degrees E and N45 degrees W, are considered as two groups of conjugate shear fractures and the former is older and is always cut by the latter. Their conjugate shear angles are 45 degrees and 85 degrees and their bisector lines are approximately in east-west and north-south directions, respectively. According to Badgeley's argumentation on the conjugate shear angles, the former conjugate shear fractures would be caused by: (1) vertical movements, and the bisector of their conjugate angle would be parallel to the long axis of horsting or folding, or (2) by a compressive force in the east-west direction and under a condition of low confining pressure and temperature.

Liu, C. C.↗
NASA NTRS1985

Observations of far-infrared transitions between excited states of OH

In observations of the Kleinmann-Low Nebula were detected of Orion 84.42 and 84.60 micron transitions between the P-2 sub 3/2 and Pi-2 sub 3/2 (J = 5/2) levels of OH with respective fluxes of 1.0 + or - 0.3 to the minus 17th power and 1.4 + or - 0.4 x 10 to the minus 17th power W cm/sq. When compared to 119 micron flux levels of OH and 153 micron flux levels of these radicals by Viscuso, these results suggest appreciable self-absorption of OH line radiation within the Nebula. It is probable that the CO emission due to the J = 31 yields 30 rotational transition at 84.411 micron makes a substantial contribution to the observed 84.42 micron flux, and that it also is at least partially absorbed at the 84.42 micron OH transition frequency. The 88.55 and 88.78 micron (J = 9/2 to 7/2) transitions of CH also were sought, but yielded only to upper limits of 3 x 10 to the minus 18th power W /sq cm each. A search of W3-IRS5 yields upper limits to the 84.42 micron OH and 87.19 micron CO (J = 30 to 29) transitions of 2 x 10 minus 18th power W cm/2.

Viscuso, P. J.↗
NASA NTRS1985

Solar wind variations and geomagnetic storms - A study of individual storms based on high time resolution ISEE 3 data

Two independent methods are employed to determine the relationship between the parameter epsilon and total energy dissipation rate of the magnetosphere U sub T by selecting disturbed periods from the same data d set used by Baker et al. (1983). Specifically, four storms are examined in detail, since the accuracy of estimating U sub T is significantly improved during disturbed periods. The first method assumes that U sub T = M sub A exp.2- alpha(epsilon) where M sub A is the Alfven Mach number and alpha varies with time. The second method considers a linear, time-invariant dynamic system with epsilon as input and U sub T as output. This means that U sub T = W(asterisk)epsilon where asterisk is the convolution and W is a transfer function characteristic of the system. It is found that alpha values fluctuate mainly between 0 and -0.25. The transfer function analysis indicates that W often resembles a delta-function or a narrow rectangular impulse. Both results give the same implication (namely that U sub T is approximately equal to epsilon) and thus are consistent with the view that the magnetosphere is primarily a directly driven system during disturbed periods.

Akasofu, S.-I.↗
NASA NTRS1984

Influence of composition on the microstructure and mechanical properties of a nickel-base superalloy single crystal

The effects of cobalt, tantaium, and tungsten contents on the microstructure and mechanical properties of single crystal Mar-M247 were investigated. Elevated temperature tensile and creep-rupture properties of 001 oriented single crystals were related to microstructural features of the alloys. Substitution of Ni for Co in the high refractory metal alloys increased the lattice mismatch, which was considered to be the cause of the increases in tensile and creep strength. Substitution of Ni for Ta caused large decreases in tensile strength and creep life, consistent with decreases in gamma prime volume fraction, lattice mismatch, and solid solution hardening. Substitution of W for Ta resulted in decreased life at high stresses, which was related to small decreases in mismatch and volume fraction. However, the W substitution resulted in improved life at low stresses, which was related to solid solution strengthening by W.

Nathal, M. V.↗
NASA NTRS1985

Honeycomb panel heat pipe development for space radiators

An assessment of the honeycomb panel heat pipe concept as a moderate temperature range, low-mass, highly efficient radiator fin for the NASA Space Station is presented, based on test results for a thin-wall (0.46 mm) all-welded stainless steel sample with core depth of 63.5 mm and a hexagonal-cell size of 127.7 mm. The 0.61 x 3.05 m test segment, operating with methanol as a working fluid, exhibited a maximum heat transfer rate of 600 W at 50 C and was isothermal to within + or - 2 C almost entirely throughout the surface. Tilt testing, which comprised relocation of the heater along one edge of the panel, resulted in maximum power levels of 70 and 50 W at panel elevations of 12.7 and 25.4 mm, respectively. As-designed panel performance is predicted to be from 500 to 1000 W over the range of operating temperatures; better performance is predicted for an open-channel design.

Tanzer, H. J.↗
NASA NTRS1985

Mean Winds of the Mesosphere (60-80 Km), as Measured by MF Radars

Winds data obtained from medium frequency (MF) radars for heights of 60 to 80 km are discussed: locations are Saskatoon (52 N, 107 W), Christchurch (44 S, 173 W), Adelside (35 S, 183 E) and Townsville (20 S, 147 E). Whereas well defined summer easterly jets centered near 70 km develop in summer, no regular buildups and decays are observed in winter at midlatitudes. Part of this variability can be associated with stratospheric warmings, which develop into breakdown of the polar vortex in the Northern Hemisphere. Amplitude and phase profiles of the annual and semiannual oscillations are also presented. The radar winds from Saskatoon are compared and combined with rocket derived winds up to 60 km from Primrose Lake (54 N, 110 W) to give consistent cross sections from 20 to 110 km. The SH radar winds are compared with a model based on rocket winds which extends up to 80 km. The latter evidence considerable smoothing, as no winter variability is evident. The other consistent difference is that heights of the summer easterly maxima for the model are 5 to 10 km lower than the radar winds at all latitudes.

Manson, A. H.↗
NASA NTRS1986

Formation and characterization of simulated small droplet icing clouds

Two pneumatic two-fluid atomizers operating at high liquid and gas pressures produced water sprays that simulated small droplet clouds for use in studying icing effects on aircraft performance. To measure median volume diameter, MVD or D sub v.5, of small droplet water sprays, a scattered-light scanning instrument was developed. Drop size data agreed fairly well with calculated values at water and nitrogen pressures of 60 and 20 psig, respectively, and at water and nitrogen pressures of 250 and 100 psig, respectively, but not very well at intermediate values of water and nitrogen pressure. MVD data were correlated with D sub 0, W sub N, and W sub w, i.e., orifice diameter, nitrogen, and water flowrate, respectively, to give the expression for MVD in microns.

Ingebo, R. D.↗
NASA NTRS1985

Development of tungsten-tantalum generator

The purpose of this project was to develop a useable tungsten (W)/tantalum (Ta) generator. Ta-178 is formed following the decay of its parent, W-178 (half-life: 21.7d) and has a half life of 9.3 minutes in turn yielding stable Hf-178. The decay of the parent isotope (W-178) occurs entirely by electron capture to the 9.3 minute Ta-178 state, without feeding the high spin Ta-178 isomer (half life 2.2 hours). In Ta-178 decay, 99.2% of the disintegrations proceed by electron capture and 0.18% by positron emission. Electron capture results in a 61.2% branch to the ground state of Hf-178 and 33.7% to the first excited state at 93 1KeV. The most prominent features of the radionuclide's energy spectrum are the hafnium characteristic radiation peaks with energies between 54.6 and 65.0 KeV. The radiation exposure dose of Ta-118 was calculated to be approximately one-twentieth that of Tc-99m on a per millicurie basis. A twenty-fold reduction in radiation exposure from Ta-178 compared with Tc-99m means that the usual administered dose can be increased three or four times, greatly increasing statistical accuracy while reducing radiation exposure by a factor of five.

Leblanc, A.↗
NASA NTRS1986

Inference of stress and texture from angular dependence of ultrasonic plate mode velocities

The theory for the angular dependence of the ultrasonic wave velocity in a symmetry plane of an orthorhombic, stressed material is presented. The two waves having polarizations in this plane are shown to have velocities which can be estimated from measurements of the SH sub 0 and S sub 0 guided modes of a thin plate: the relationship being exact for the SH sub 0 mode and requiring a 10% correction for the S sub 0 mode at long wavelength. It is then shown how stress and texture can be independently inferred from various features of the angular dependence of these two velocities. From the SH sub 0 data, the ability to determine the directions and differences in magnitudes of principal stresses is described and supported by experimental data on several materials. From a combination of the SH sub 0 and S sub 0 data, a procedure is proposed for determining the coefficients W sub 400, W sub 420 and W sub 440 of an expansion of the crystallite orientation distribution function in terms of generalized Legendre functions. Possible applications in process control are indicated.

Thompson, R. B.↗
NASA NTRS1986

Dynamic remapping of parallel computations with varying resource demands

A large class of computational problems is characterized by frequent synchronization, and computational requirements which change as a function of time. When such a problem must be solved on a message passing multiprocessor machine, the combination of these characteristics lead to system performance which decreases in time. Performance can be improved with periodic redistribution of computational load; however, redistribution can exact a sometimes large delay cost. We study the issue of deciding when to invoke a global load remapping mechanism. Such a decision policy must effectively weigh the costs of remapping against the performance benefits. We treat this problem by constructing two analytic models which exhibit stochastically decreasing performance. One model is quite tractable; we are able to describe the optimal remapping algorithm, and the optimal decision policy governing when to invoke that algorithm. However, computational complexity prohibits the use of the optimal remapping decision policy. We then study the performance of a general remapping policy on both analytic models. This policy attempts to minimize a statistic W(n) which measures the system degradation (including the cost of remapping) per computation step over a period of n steps. We show that as a function of time, the expected value of W(n) has at most one minimum, and that when this minimum exists it defines the optimal fixed-interval remapping policy. Our decision policy appeals to this result by remapping when it estimates that W(n) is minimized. Our performance data suggests that this policy effectively finds the natural frequency of remapping. We also use the analytic models to express the relationship between performance and remapping cost, number of processors, and the computation's stochastic activity.

Nicol, D. M.↗