Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Transfer function design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Analysis and calculation of lightning-induced voltages in aircraft electrical circuits

Techniques to calculate the transfer functions relating lightning-induced voltages in aircraft electrical circuits to aircraft physical characteristics and lightning current parameters are discussed. The analytical work was carried out concurrently with an experimental program of measurements of lightning-induced voltages in the electrical circuits of an F89-J aircraft. A computer program, ETCAL, developed earlier to calculate resistive and inductive transfer functions is refined to account for skin effect, providing results more valid over a wider range of lightning waveshapes than formerly possible. A computer program, WING, is derived to calculate the resistive and inductive transfer functions between a basic aircraft wing and a circuit conductor inside it. Good agreement is obtained between transfer inductances calculated by WING and those reduced from measured data by ETCAL. This computer program shows promise of expansion to permit eventual calculation of potential lightning-induced voltages in electrical circuits of complete aircraft in the design stage.

Plumer, J. A.↗
DOE OSTI2022

Effects of Temperature on Flow Fouling of Smooth and Nonwetting Surfaces

Mineral fouling (scaling) of heat transfer surfaces is a pervasive problem in heat exchangers, chemical reactors, and other equipment in energy, environmental, and process industrial applications. Many of the applications involve dynamic flow of fluids with the impurity minerals and, furthermore, operate at elevated temperature. Strategies to mitigate fouling under these conditions are of much value in industrial applications. This paper presents a comparative study of temperature-dependent mineral fouling deposition on smooth surfaces and nonwetting superhydrophobic and lubricant-infused surfaces under dynamic flow conditions. The surfaces are represented in a unified manner using the viscosity ratio of the infused material within the porous asperities on a surface to that of the flowing fluid such that the spectrum of surfaces from superhydrophobic to smooth is captured by the range of viscosity ratios from 0 to ∞. Using a forced convection experimental setup, deposition of calcium sulfate on the surfaces is quantified in terms of asymptotic fouling resistance over a range of temperature, Reynolds number, and mineral foulant supersaturation. Through a systematic set of accelerated fouling experiments, an empirical relationship for the asymptotic fouling resistance is developed in terms of Reynolds number, foulant concentration, temperature, and surface type. The empirical model is validated with a comprehensive set of experimental data from this study as well as from the literature. Optimum nonwetting surface designs for minimizing fouling resistance compared to conventional smooth surfaces are developed as a function of temperature. The results of the study offer insight into the temperature-dependent fouling of surfaces under flow conditions and a rational design of fouling-resistant nonwetting surfaces that can be readily translated to practice.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

The effects of active site and support on hydrogen elimination over transition-metal-functionalized yttria-decorated metal–organic frameworks

Hydrogen elimination from a metal alkyl complex and its reverse reaction are critical elementary steps in many catalytic cycles. In understanding such catalytic cycles, it is important to learn about the effect of the active site as well as effects beyond the active site, especially support effects. Here we employ density-functional-theory-based computational screening of transition-metal-functionalized yttria-decorated NU-1000 metal–organic frameworks to study the effect of metal sites and supports on the hydrogen elimination reactions. In this work, we consider six transition metals. The screening shows that a Nb-based catalyst has the lowest free energy of activation for both α-H elimination and β-H elimination, but for the latter we must also consider the free energy of release of the alkene. By the Sabatier principle, the optimal catalyst for β-H elimination is the one that interacts with molecules with intermediate strength for easy reactant activation as well as easy product desorption. By employing a volcano plot to find the optimum compromise, we identified V-functionalized, yttria-decorated NU-1000 as the most active catalyst among the trial candidates for the β-H elimination reaction. The analysis also reveals a support-specific charge transfer process in which the yttria and carboxylate linkers enable electron transfer between the transition-metal site and organic linkers of the NU-1000 simultaneously with a coordinated change of spin at the metal site and in the linker groups. Based on our analyses, we hypothesize that the observed charge transfer enables certain functional groups, such as propyl, to interact more strongly with the support and stabilize the catalyst.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Late Metal Sandwich Catalysts for Olefin Polymerization

Polyolefins are by far the most ubiquitous industrially produced polymers and are primarily produced by early transition metal catalysts. These catalysts are not functional group tolerant, and copolymerization of ethylene and polar vinyl monomers is quite challenging. Furthermore, early metal catalysts convert ethylene to linear polyethylene, and introduction of branches requires addition of comonomers. In this Account, we describe our efforts in designing and implementing new Pd(II) and Ni(II) olefin polymerization catalysts based on mechanistic understanding of the chain growth process. Here, the original hindered nickel- and palladium-aryl-substituted diimine complexes were discovered in 1995. The key to the success of these now “classic” systems in generating high polymers rather than dimers or oligomers was realizing that incorporation of ortho-disubstituted aryl groups partially blocks the axial sites of the metal and thus retards the rate of chain transfer relative to propagation. Two key features of these late metal catalysts distinguish them from early metal complexes. First, they tolerate certain functional groups, which allows copolymerization of olefins with polar comonomers. Second, they can form a branched polymer from ethylene without the need to add α-olefin comonomers. Importantly, for nickel catalysts, branching levels can be modulated by changing reaction conditions, such as temperature and monomer pressure.

Catalysts↗
DOE OSTI2025

Structure–Function Relationships in Sequence-Controlled Copolymers for Rare Earth Element Chelation

The ability to tune material function through primary sequence is a defining feature of biological macromolecules, allowing precise control over structure and target interactions in complex aqueous environments. However, translating sequence–structure–function relationships to synthetic macromolecules is challenging due to their dispersity in sequence, conformation, and composition. Here, we report systematic studies of amphiphilic polymer chelators designed to probe how composition and patterning influence binding affinity and selectivity for rare earth elements (REEs), a series of technologically relevant metals with challenging separation profiles. A library of copolymers varying hydrophobic monomer composition and patterning was synthesized via reversible addition–fragmentation chain transfer (RAFT) polymerization, spanning statistical, gradient, and block architectures. REE binding was quantified using a high-throughput colorimetric assay, and reconstruction of polymer ensembles using kinetic stochastic simulations enabled quantitative comparisons of sequence heterogeneity, linking local monomer colocalization to emergent REE binding. Further, we investigated the role of different hydrophobic comonomers in tuning metal coordination, with binding trends linked to structural features that influence binding site desolvation. Complementary dynamic light scattering (DLS) and small-angle X-ray scattering (SAXS) measurements showed that both polymer and monomer architecture modulate metal-induced conformational changes, and that multichain assembly behavior emerges beyond critical hydrophobic thresholds. Sequence control also altered REE selectivity, with nonmonotonic differences observed across compositionally identical polymers with different sequence architectures. Together, these findings establish design principles that connect polymer sequence and structure to binding performance, guiding the design of macromolecular chelators with enhanced affinity and selectivity for applications in separations, sensing, and catalysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Conjugation- and Aggregation-Directed Design of Covalent Organic Frameworks as White-Light-Emitting Diodes

2D covalent organic frameworks (COFs) have emerged as a promising class of organic luminescent materials due to their structural diversity, which allows the systematic tuning of organic building blocks to optimize emitting properties. However, a significant knowledge gap exists between the design strategy and the fundamental understanding of the key structural parameters that determine their photophysical properties. Here, in this work, we report two highly emissive sp 2 -C-COFs and the direct correlation of the structure (conjugation and aggregation) with their light absorption/emission, charge transfer (CT), and exciton dynamics, the key properties that determine their function as luminescent materials. We show that white light can be obtained by simply coating COFs on an LED strip or mixing the two COFs. Using the combination of time-resolved absorption and emission spectroscopy as well as computational prediction, we show that the planarity, conjugation, orientation of the dipole moment, and interlayer aggregation not only determine the light-harvesting ability of COFs but also control the exciton relaxation pathway and photoluminescent quantum yield.

14 SOLAR ENERGY↗
DOE OSTI2025

Cavity electrodynamics of van der Waals heterostructures

Van der Waals heterostructures host many-body quantum phenomena that are tunable in situ using electrostatic gates. Their constituent two-dimensional materials and gates can naturally form plasmonic self-cavities, confining light in standing waves of current density due to finite-size effects. The plasmonic resonances of typical graphite gates fall in the gigahertz to terahertz range, corresponding to the same microelectronvolt to millielectronvolt energy scale as the phenomena in van der Waals heterostructures that they electrically control. This raises the possibility that the built-in cavity modes of graphite gates are relevant for shaping the low-energy physics of these heterostructures. However, probing these cavity-coupled electrodynamics is challenging as devices are notably smaller than the diffraction limit at the relevant wavelengths. Here we report on the intrinsic cavity conductivity of gate-tunable graphene heterostructures. As the carrier density is tuned, we observe coupling and spectral weight transfer between graphene and graphite plasmonic cavity modes in the ultrastrong coupling regime. We present an analytical model to describe the results and provide general principles for cavity design. Our findings show that intrinsic cavity effects are important for understanding the low-energy electrodynamics of van der Waals heterostructures and open a pathway for useful functionality through cavity control.

Electronic properties and materials↗
DOE OSTI2019

Validation of RELAP-7 for Forced Convective and Natural Circulation Reactor Flows

New reactor designs such as small modular reactors and newly proposed passive safety systems rely on natural circulation two-phase flow cooling of the reactor core under accident conditions. Without a pump to drive the flow, the circulation rate is a strong function of void fraction. Under these conditions where the flow rate, pressure drop, and heat transfer are all closely coupled through the mixture density, the accurate prediction of void fraction is pivotal. Furthermore, while these passive systems boast a more reliable cooling option, the sensitivity of the system to two-phase flow instabilities is more likely than in forced convective cooling and can result in dangerous density wave or flow excursion conditions. Improvement of one-dimensional system codes and further development of three-dimensional code capability are all important efforts in addressing these issues. The proposed work is a critical step towards providing confidence through validation of the capability of thermal-hydraulic tools to meet the emerging challenges in reactor simulation. Historically, system analysis codes develop a stiffness over time due to fine-tuning of adjustable code parameters that result in a reluctance or inability to adopt improved models. Therefore, a rigorous effort should be invested in preparation for RELAP-7 to identify required modeling improvements of constitutive relations and validation of the code applicability to the wide range of possible reactor flow conditions. Part of this validation involves the uncertainty quantification which is a critical step in the Code Scaling, Applicability, and Uncertainty (CSAU) methodology and Best-Estimate Plus Uncertainty (BEPU) licensing method. BEPU allows recovery of safety margins and potentially optimizing plant performance, resulting in economic benefit for the reactor operators. Beginning with the collection of past experimental data covering prototypic LWR conditions, this document reviews three critical datasets available for the validation of system codes. The experimental methods, procedures, facilities, instrumentation, and supplementary information are consolidated to aid the validation efforts of this work and future projects. These three datasets (824 conditions) are chosen due to their wide acceptance and demonstrated application for code validation. Two experimental datasets from the Nuclear Power Engineering Corporation (NUPEC) span prototypic conditions of Boiling Water Reactors (BWR) and Pressurized Water Reactors (PWR). These datasets are labeled as the BFBT (BWR Full-size Fine-mesh Bundle Test) and the PSBT (PWR Subchannel and Bundle Test) datasets respectively. The third dataset is taken in an internally heated annulus that is scaled based on a BWR subassembly and includes two-phase flows important to post-blowdown analysis. Together, the datasets consider the full range of pressure and mass flux expected in LWR forced convective flows from steady-state to long term cooling conditions. Recognizing the deficiency of available data under low-pressure, low-flow, a new natural circulation dataset consisting of 107 conditions is obtained. With system pressures ranging between 145 and 950 kPa, natural circulation is driven by a heat flux up to 275 kW/m2 in a 3 m long heated region of the annulus test section which is followed by a 2 m long unheated region before entering a condenser. Stable natural circulation flow rates in this facility were measured to be between 182 and 590 kg/m2-s. Pressure and temperature are measured at ten locations in the facility. In addition, measurements of void fraction, interfacial area concentration, and gas velocity are obtained at five axial locations in the annulus test section. The RELAP5-3D code demonstrates good accuracy for void fraction predictions in BFBT and PSBT benchmarks, but shows relatively large discrepancy in the annulus experiments at lower pressures. In two-phase natural circulation, large oscillations are observed in many system parameters during the simulation of 19 experiment cases which were conducted at low pressures, and the model shows good predictive performance with the remaining 88 experiment cases. However, some discrepancies in void fraction and temperature predictions are found which may require improved constitutive modeling under these low-pressure, low-flow condition. The quantified uncertainty in void fraction predictions in three forced convection benchmarks due to uncertainties in boundary conditions and geometries are relatively small, except for a few cases in the annulus experiment. The output uncertainty of the natural circulation model is quantified by considering the measurement error in boundary conditions, and it is shown that the output uncertainty ranges are relatively small for the range of conditions considered. Through this work, a clear pathway is provided for validation of RELAP7 once the code is available.

42 ENGINEERING↗
NASA NTRS1978

Water system microbial check valve development

Development work on a device for the Space Shuttle that will prevent the transfer of viable microorganisms within water systems is described. The device serves as a check valve in that it prevents the transfer or cross-contamination of microorganisms from a nonpotable system into a potable water system when these systems are interconnected. In this regard, the function of the device is similar to that of the air gap found in conventional one gravity systems. The device is essentially a bed of resin material impregnated with iodine. Basic design data for a variety of flow and temperature conditions are presented, together with results of challenging the beds with suspensions of seven microorganisms including aerobes, anaerobes, and spore formers.

Colombo, G. V.↗
NASA NTRS2001

Patterns of transfer of adaptation among body segments

Two experiments were conducted in order to determine the patterns of transfer of visuomotor adaptation between arm and head pointing. An altered gain of display of pointing movements was used to induce a conflict between visual and somatosensory representations. Two subject groups participated in Experiment 1: group 1 adapted shoulder pointing movements, and group 2 adapted wrist pointing movements to a 0.5 gain of display. Following the adaptation regimen, subjects performed a transfer test in which the shoulder group performed wrist movements and the wrist group performed shoulder movements. The results demonstrated that both groups displayed typical adaptation curves, initially undershooting the target followed by a return to baseline performance. Transfer tests revealed that both groups had high transfer of the acquired adaptation to the other joint. Experiment 2 followed a similar design except that group 1 adapted head pointing movements and group 2 adapted arm pointing movements. The arm adaptation had high transfer to head pointing while the head adaptation had very little transfer to arm pointing. These results imply that, while the arm segments may share a common target representation for goal-directed actions, individual but functionally dependent target representations may exist for the control of head and arm movements.

NASA Center JSC↗
NASA NTRS2000

Patterns of Transfer of Adaptation Among Body Segments

Two experiments were conducted in order to determine the patterns of transfer of visuomotor adaptation between arm and head pointing. An altered gain of display of pointing movements was used to induce a conflict between visual and somatosensory representations. Two subject groups participated in Experiment One: group 1 adapted shoulder pointing movements, and group 2 adapted wrist pointing movements to a 0.5 gain of display. Following the adaptation regimen, subjects performed a transfer test in which the shoulder group performed wrist movements and the wrist group performed shoulder movements. The results demonstrated that both groups displayed typical adaptation curves, initially undershooting the target followed by a return to baseline performance. Transfer tests revealed that both groups had high transfer of the acquired adaptation to the other joint. Experiment Two followed a similar design except that group 1 adapted head pointing movements and group 2 adapted arm pointing movements. The arm adaptation had high transfer to head pointing while the head adaptation had very little transfer to arm pointing. These results imply that, while the arm segments may share a common target representation for goal-directed actions, individual but functionally dependent target representations may exist for the control of head and arm movements.

Seidler, R. D.↗
NASA NTRSDate not supplied

Risk Reduction Project in Pad Abort-1 Launch Vehicle Loads & Dynamics

The Pad Abort (PA-1) system includes the Launch Abort System (LAS) and the Command Module (CM). The PA-1 abort flight test will launch from the White Sands Missile Range. Prior to the ignition, the vehicle will be resting, without restraints, on a short support structure. The Launch Abort Motor will ignite and burn for less than 5 seconds before a 20 second coast. Then the LAS will separate from the CM and the CM will descend via parachute to a soil landing. The static firing of the Abort Motor (ST-1) for PA-1 Launch Vehicle resulted in unexpected higher levels that superseded the environment predictions and all the design and test loads of all subassemblies and components. A rapid project was put in place to develop the flight environments, loads and associated uncertainties for the Verification Load Cycle (VLC) of PA-1. An acoustic test and shaker test of the CM were planned and executed in support of the developments of damping and transfer functions. Instead of using the traditional structure-borne envelops, the actual ST-1 pressures and forces were used to develop the internal accelerations. The PA-1 motor was cooled to 60 Deg F using thermal conditioning to reduce the thrust profile. The plumes of the abort motor were studied to determine if the airborne environments would be reduced. The combination of all items, noted above, allowed a reduction in loads for VLC.

Sasan C Armand↗
DOE OSTI2021

Revealing the effect of interfacial electron transfer in heterostructured Co 9 S 8 @NiFe LDH for enhanced electrocatalytic oxygen evolution

Heterointerface engineering is a desirable way to rationally design efficient and low-cost electrocatalysts for the oxygen evolution reaction (OER). Herein, urchin-like Co 9 S 8 @NiFe layered double hydroxide (Co 9 S 8 @NiFe LDH) heterostructured hollow spheres are assembled from Co 9 S 8 hollow spheres as the core and porous NiFe LDH nanowires as the shell. The heterostructured hollow spheres show a small overpotential of 220 mV at a current density of 10 mA cm -2 , a low Tafel slope of 52.0 mV dec -1 , and robust stability, which is better than that of commercial IrO 2 and most reported non-precious electrocatalysts. Density functional theory (DFT) calculations show that the synergetic effect at the interface could improve the electrical conductivity of Co 9 S 8 @NiFe LDH, induce electron transfer from NiFe LDH to Co 9 S 8 , and lower the energy barriers of intermediates for the OER, leading to enhanced electrocatalytic activity. Meanwhile, the urchin-like hollow structure with nanopores and super-hydrophilicity can provide desired structural stability, facilitate ion penetration and release bubbles, improving the accessibility of active sites and thereby boosting OER catalytic performance. This work provides a viable route to develop high performance electrocatalysts for the OER.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Delocalized Excitation Transfer in Open Quantum Systems with Long-Range Interactions

The interplay between coherence and system-environment interactions is at the basis of a wide range of phenomena, from quantum information processing to charge and energy transfer in molecular systems, biomolecules, and photochemical materials. In this work, we use a Frenkel exciton model with long-range interacting qubits coupled to a damped collective bosonic mode to investigate vibrationally assisted transfer processes in donor-acceptor systems featuring internal substructures analogous to light-harvesting complexes. We find that certain delocalized excitonic states maximize the transfer rate and that the entanglement is preserved during the dissipative transfer over a wide range of parameters. We investigate the reduction in transfer caused by static disorder, white noise, and finite temperature and study how transfer efficiency scales as a function of the number of dimerized monomers and the component number of each monomer, finding which excitonic states lead to optimal transfer. Finally, we provide a realistic experimental setting to realize this model in analog trapped-ion quantum simulators. Analog quantum simulation of systems comprising many and increasingly complex monomers could offer valuable insights into the design of light-harvesting materials, particularly in the nonperturbative intermediate parameter regime examined in this study, where classical simulation methods are resource intensive.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1972

Space tools and support equipment - Current technology and future requirements.

Space tools and supporting equipment developed for past and current missions are summarized, along with projected tool and powered maneuvering aid requirements for future earth orbital missions. These tools, designed for functions such as general maintenance, replacement and repair, are reviewed and classified according to their intended application. A synopsis of the Skylab on-orbit maintenance requirements is presented, and the tools necessary for accomplishing the maintenance functions are listed. The proposed missions for future Earth Orbital Systems are summarized, and the potential functions (e.g., Remove/Replace, Cargo Transfer, etc.) are outlined. The current tool and support technology status is compared with future requirements for crew equipment to determine if these future requirements can be adequately satisfied. Of particular interest is a discussion of the augmentation of the astronaut with teleoperators (remote manipulator systems).

Brown, N. E.↗
NASA NTRS1982

Interaction between the SPS solar power satellite solar array and the magnetospheric plasma

The results of study to determine the effects of space plasmas on a large GaAs solar cell array using solar reflectors at a concentration ratio of two in geostationary orbit are summarized. It was concluded that the system could function in the GEO environment if certain design changes were implemented. These included conductive coatings on the solar cells, changing the reflector material from Kapton to a higher conductivity material, and oversizing the array to compensate for a 0.7% parasitic load due to losses from the ambient magnetospheric plasma. The operation of the solar powered earth orbit transfer vehicle (EOTV) was also examined and it was concluded that LEO servere arcing would take place on all high voltage negative portions of the array. The parasitic load loss at LEO was estimated at 3%. Operation of a high voltage array at LEO represents a major problem. Charge exchange ion feedback from argon ion thrusters located near the EOTV solar array was also examined and all problems found were believed to be solvable by the placement of protective ground screens.

Freeman, J. W.↗
NASA NTRS1995

PPT Thrust Stand

A torsional-type thrust stand has been designed and built to test Pulsed Plasma Thrusters (PPT's) in both single shot and repetitive operating modes. Using this stand, momentum per pulse was determined strictly as a function of thrust stand deflection, spring constant, and natural frequency. No empirical corrections were required. The accuracy of the method was verified using a swinging impact pendulum. Momentum transfer data between the thrust stand and the pendulum were consistent to within 1%. Following initial calibrations, the stand was used to test a Lincoln Experimental Satellite (LES-8/9) thruster. The LES-8/9 system had a mass of approximately 7.5 kg, with a nominal thrust to weight ratio of 1.3 x 10(exp -5). A total of 34 single shot thruster pulses were individually measured. The average impulse bit per pulse was 266 microN-s, which was slightly less than the value of 300 microN-s published in previous reports on this device. Repetitive pulse measurements were performed similar to ordinary steady-state thrust measurements. The thruster was operated for 30 minutes at a repetition rate of 132 pulses per minute and yielded an average thrust of 573 microN. Using average thrust, the average impulse bit per pulse was estimated to be 260 microN-s, which was in agreement with the single shot data. Zero drift during the repetitive pulse test was found to be approximately 1% of the measured thrust.

Haag, Thomas W.↗
NASA NTRS2006

Multifunctional Tanks for Spacecraft

A document discusses multifunctional tanks as means to integrate additional structural and functional efficiencies into designs of spacecraft. Whereas spacecraft tanks are traditionally designed primarily to store fluids and only secondarily to provide other benefits, multifunctional tanks are designed to simultaneously provide multiple primary benefits. In addition to one or more chamber(s) for storage of fluids, a multifunctional tank could provide any or all of the following: a) Passageways for transferring the fluids; b) Part or all of the primary structure of a spacecraft; c) All or part of an enclosure; d) Mechanical interfaces to components, subsystems, and/or systems; e) Paths and surfaces for transferring heat; f)Shielding against space radiation; j) Shielding against electromagnetic interference; h) Electrically conductive paths and surfaces; and i) Shades and baffles to protect against sunlight and/or other undesired light. Many different multifunctional-tank designs are conceivable. The design of a particular tank can be tailored to the requirements for the spacecraft in which the tank is to be installed. For example, the walls of the tank can be flat or curved or have more complicated shapes, and the tank can include an internal structure for strengthening the tank and/or other uses.

Collins, David H.↗