Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TEST METHOD”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

Fracture mechanics life analytical methods verification testing

The objective was to evaluate NASCRAC (trademark) version 2.0, a second generation fracture analysis code, for verification and validity. NASCRAC was evaluated using a combination of comparisons to the literature, closed-form solutions, numerical analyses, and tests. Several limitations and minor errors were detected. Additionally, a number of major flaws were discovered. These major flaws were generally due to application of a specific method or theory, not due to programming logic. Results are presented for the following program capabilities: K versus a, J versus a, crack opening area, life calculation due to fatigue crack growth, tolerable crack size, proof test logic, tearing instability, creep crack growth, crack transitioning, crack retardation due to overloads, and elastic-plastic stress redistribution. It is concluded that the code is an acceptable fracture tool for K solutions of simplified geometries, for a limited number of J and crack opening area solutions, and for fatigue crack propagation with the Paris equation and constant amplitude loads when the Paris equation is applicable.

Favenesi, J. A.↗

Discovery and Analysis of Rare High-Impact Failure Modes using Adversarial RL-Informed Sampling

Adaptive learning agents have tremendous potential to handle critical tasks currently performed by humans. Unfortunately, due to their complexity, it can be difficult to verify that these learning agents do not have critical failure modes. Standard verification and validation methods often do not apply directly to learning agents and Monte Carlo methods have difficulty covering even a small fraction of the state space, especially in multiagent systems or over long time horizons. To overcome this difficulty, we demonstrate an adaptive stress-testing method based on reinforcement learning of correlations that raise the probability of failure. This approach has three key properties: (1) it is able to find rare failure modes with far greater sample efficiency than Monte Carlo methods, (2) it can estimate the true probability of a failure mode despite the inherent bias in the learning method, and (3) it is capable of learning and resampling compact representations of multimodal failure spaces. These properties are important in practice as we need to find disparate failure modes while accounting for their actual relevance. This is a significant advantage over traditional adaptive stress testing methods that give abstract likelihoods of particular failure instances, but cannot estimate the probability of a broader failure mode. We test our algorithm on a simple problem from the aviation domain where an autonomous aircraft lands in gusty wind conditions. The results suggest that we can find failure modes with far fewer samples than the Monte Carlo approach and simultaneously estimate the probability of failure.

reinforcement learning↗

Discovery and Analysis of Rare High-Impact Failure Modes using Adversarial RL-Informed Sampling

Adaptive learning agents have tremendous potential to handle critical tasks currently performed by humans. Unfortunately, due to their complexity, it can be difficult to verify that these learning agents do not have critical failure modes. Standard verification and validation methods often do not apply directly to learning agents and Monte Carlo methods have difficulty covering even a small fraction of the state space, especially in multiagent systems or over long time horizons. To overcome this difficulty, we demonstrate an adaptive stress-testing method based on reinforcement learning of correlations that raise the probability of failure. This approach has three key properties: (1) it is able to find rare failure modes with far greater sample efficiency than Monte Carlo methods, (2) it can estimate the true probability of a failure mode despite the inherent bias in the learning method, and (3) it is capable of learning and resampling compact representations of multimodal failure spaces. These properties are important in practice as we need to find disparate failure modes while accounting for their actual relevance. This is a significant advantage over traditional adaptive stress testing methods that give abstract likelihoods of particular failure instances, but cannot estimate the probability of a broader failure mode. We test our algorithm on a simple problem from the aviation domain where an autonomous aircraft lands in gusty wind conditions. The results suggest that we can find failure modes with far fewer samples than the Monte Carlo approach and simultaneously estimate the probability of failure.

Validation↗

Discovery and Analysis of Rare High-Impact Failure Modes using Adversarial RL-Informed Sampling

Adaptive learning agents have tremendous potential to handle critical tasks currently performed by humans. Unfortunately, due to their complexity, it can be difficult to verify that these learning agents do not have critical failure modes. Standard verification and validation methods often do not apply directly to learning agents and Monte Carlo methods have difficulty covering even a small fraction of the state space, especially in multiagent systems or over long time horizons. To overcome this difficulty, we demonstrate an adaptive stress-testing method based on reinforcement learning of correlations that raise the probability of failure. This approach has three key properties: (1) it is able to find rare failure modes with far greater sample efficiency than Monte Carlo methods, (2) it can estimate the true probability of a failure mode despite the inherent bias in the learning method, and (3) it is capable of learning and resampling compact representations of multimodal failure spaces. These properties are important in practice as we need to find disparate failure modes while accounting for their actual relevance. This is a significant advantage over traditional adaptive stress testing methods that give abstract likelihoods of particular failure instances, but cannot estimate the probability of a broader failure mode. We test our algorithm on a simple problem from the aviation domain where an autonomous aircraft lands in gusty wind conditions. The results suggest that we can find failure modes with far fewer samples than the Monte Carlo approach and simultaneously estimate the probability of failure.

Validation↗

Monte Carlo burnup code acceleration with the correlated sampling method. Preliminary test on an UOX cell with TRIPOLI-4{sup R}

For several years, Monte Carlo burnup/depletion codes have appeared, which couple a Monte Carlo code to simulate the neutron transport to a deterministic method that computes the medium depletion due to the neutron flux. Solving Boltzmann and Bateman equations in such a way allows to track fine 3 dimensional effects and to get rid of multi-group hypotheses done by deterministic solvers. The counterpart is the prohibitive calculation time due to the time-expensive Monte Carlo solver called at each time step. Therefore, great improvements in term of calculation time could be expected if one could get rid of Monte Carlo transport sequences. For example, it may seem interesting to run an initial Monte Carlo simulation only once, for the first time/burnup step, and then to use the concentration perturbation capability of the Monte Carlo code to replace the other time/burnup steps (the different burnup steps are seen like perturbations of the concentrations of the initial burnup step). This paper presents some advantages and limitations of this technique and preliminary results in terms of speed up and figure of merit. Finally, we will detail different possible calculation scheme based on that method. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

An investigation of the Iosipescu and Asymmetrical Four-Point Bend tests for composite materials

The results of an extensive analytical and experimental investigation of the Iosipescu and Asymmetrical Four-Point Bend (AFPB) test methods are summarized. Finite element analyses were used to assess the influence of notch parameters and load locations on the stress state in the specimens. The shear moduli and shear strengths were experimentally measured for quasi-isotropic graphite-epoxy laminates using both the Iosipescu and the AFPB test methods with various combinations of notch parameters and load locations. The test results indicate that changes in the notch geometry and load locations aimed at improving the stress distribution in the test section result in unexpected changes in the failure mode.

Spigel, B. S.↗

Evaluation of the Reliability of Passive Infrared (PIR) Occupancy Sensors for Residential Indoor Lighting

Solid-state lighting (SSL) technologies have penetrated the general illumination market in recent years, largely replacing conventional technologies such as incandescent and fluorescent lighting. Most of the initial excitement about light-emitting diode (LED) sources for SSL devices focused on their energy savings potential resulting from vast improvements in source efficiency and luminous efficacy compared with conventional illumination products. More recently, the focus has shifted toward other aspects of lighting application efficiency, namely intensity effectiveness and spectral efficiency, because of the ease of controlling both the light intensity of LEDs with drive voltage and the color properties of the LED-based illuminators. To capitalize on the energy savings of increased intensity effectiveness and spectral efficiency, a lighting control system (LCS) is often used. While the current penetration of LCSs is relatively modest, it is anticipated that lighting controls (i.e., connected lighting, controls and LED and conventional lighting) could have an installed penetration as higher as 46% by the year 2035, saving an additional 1.3 quads of energy. Despite the large energy savings that can be gained from using LCSs, standard test methods for evaluating sensors employed in LCSs and reliability data of the LCSs and their components are generally lacking. The National Electrical Manufacturers Association (NEMA) developed the only standard, NEMA WD 7-2011 (R2016), to test occupancy and motion sensor performance (herein referred to as “the NEMA protocol”). In a previous U.S. Department of Energy (DOE) effort, some concerns of the NEMA protocol were identified (e.g., strict height and weight limits on test subjects, large amounts of manual effort, sometimes inconsistent repeatability). During the current work, a consistent detection length test (DLT) and a Robotic Sensor Evaluation System (RoboSES) were developed to alleviate some of these concerns. RoboSES acts as a human surrogate by using thermal pads on a mannequin and a remote-controlled mobile base to test a sensor’s field of view (FOV). This report builds on the earlier DOE efforts to understand sensor technologies used in LCSs for general illumination. Specifically, this report describes the optimization of RoboSES, characterizes and establishes test methods to assess the reliability of multiple passive infrared (PIR) sensors, and reports the findings of robustness and reliability testing on two commercial PIR sensors intended for residential applications. The information presented in this report is gained from up to 4,000 hours (hrs) of accelerated stress tests (ASTs).

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Degradation Characterization of Thermal Interface Greases: Preprint

Thermal interface materials (TIMs) are used in power electronics packaging to minimize thermal resistance between the heat generating component and the heat sink. Thermal greases are one such class. The conformability and thin bond line thickness (BLT) of these TIMs can potentially provide low thermal resistance throughout the operation lifetime of a component. However, their performance degrades over time due to pump-out and dry-out during thermal and power cycling. The reliability performance of greases through operational cycling needs to be quantified to develop new materials with superior properties. NREL, in collaboration with DuPont, has performed thermal and reliability characterization of several commercially available thermal greases. Initial bulk and contact thermal resistance of grease samples were measured, and then the thermal degradation that occurred due to pump-out and dry-out during temperature cycling was monitored. The thermal resistances of five different grease materials were evaluated using NREL's steady-state thermal resistance tester based on the ASTM test method D5470. Greases were then applied, utilizing a 2.5 cm x 2.5 cm stencil, between invar and aluminum plates to compare the thermomechanical performance of the materials in a representative test fixture. Scanning Acoustic microscopy, thermal, and compositional analyses were performed periodically during thermal cycling from -40 degrees Celcius to 125 degrees Celcius. Completion of this characterization has allowed for a comprehensive evaluation of thermal greases both for their initial bulk and contact thermal performance, as well as their degradation mechanisms under accelerated thermal cycling conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Iosipescu shear properties of graphite fabric/epoxy composite laminates

The Iosipescu shear test method is used to measure the in-plane and interlaminar shear properties of four T300 graphite fabric/934 epoxy composite materials. Different weave geometries tested include an Oxford weave, a 5-harness satin weave, an 8-harness satin weave, and a plain weave with auxiliary warp yarns. Both orthogonal and quasi-isotropic layup laminates were tested. In-plane and interlaminar shear properties are obtained for laminates of all four fabric types. Overall, little difference in shear properties attributable to the fabric weave pattern is observed. The auxiliary warp material is significantly weaker and less stiff in interlaminar shear parallel to its fill direction. A conventional strain gage extensometer is modified to measure shear strains for use with the Iosipescu shear test. While preliminary results are encouraging, several design iterations failed to produce a reliable shear transducer prototype. Strain gages are still the most reliable shear strain transducers for use with this test method.

Walrath, D. E.↗

Nonlinear Unsteady Aerodynamic Modeling Using Wind Tunnel and Computational Data

Extensions to conventional aircraft aerodynamic models are required to adequately predict responses when nonlinear unsteady flight regimes are encountered, especially at high incidence angles and under maneuvering conditions. For a number of reasons, such as loss of control, both military and civilian aircraft may extend beyond normal and benign aerodynamic flight conditions. In addition, military applications may require controlled flight beyond the normal envelope, and civilian flight may require adequate recovery or prevention methods from these adverse conditions. These requirements have led to the development of more general aerodynamic modeling methods and provided impetus for researchers to improve both techniques and the degree of collaboration between analytical and experimental research efforts. In addition to more general mathematical model structures, dynamic test methods have been designed to provide sufficient information to allow model identification. This paper summarizes research to develop a modeling methodology appropriate for modeling aircraft aerodynamics that include nonlinear unsteady behaviors using both experimental and computational test methods. This work was done at Langley Research Center, primarily under the NASA Aviation Safety Program, to address aircraft loss of control, prevention, and recovery aerodynamics.

Murphy, Patrick C.↗

Investigation of nonlinear mechanical behavior of two superfine-grained graphites with DIC assisted disc splitting test

Using standardized uniaxial tensile test specimens is not practical due to the limited volumes in irradiation capsules, molten salt degradation facilities, or oxidation apparatus. The ASTM International Standard Test Method for Tensile Strength Estimate by Disc Compression of Manufactured Graphite (ASTM D8289) was developed to provide a convenient way for estimating tensile strength. Unlike the traditional uniaxial tensile test in ASTM C749 (International Standard Test Method for Tensile Stress–Strain of Carbon and Graphite), which uses dog-bone shaped specimens larger than 12.95 mm × 120.65 mm, the ASTM D8289 standard uses smaller discs with diameters of 6–12.7 mm. A digital image correlation (DIC) system, which uses a full-field noncontact surface displacement measurement technique, was applied along with the ASTM D8289 disc splitting test on IG-110 samples and compared with previous measurements from Mersen 2114 samples. Results confirmed that the DIC technique can measure the surface displacement/strain on these small (Ø6 mm × 3 mm) graphite specimens with good repeatability. However, Mersen 2114 and IG-110 samples exhibited strain discrepancies when DIC measurements were compared with analytical and finite element simulation values. The loading history and strain results also indicated different mechanical behaviors between Mersen 2114 and IG-110, particularly the nonlinear behavior of the IG-110 samples. Good agreement was observed by comparing the splitting tensile strengths of two superfine-grained grades with results from other work. The specimen size effect is discussed when comparing the splitting tensile strength with corresponding uniaxial tensile strength of these two graphite grades.

Lin, Lianshan [ORNL] (ORCID:0000000203399219)↗

Bond Testing for Effects of Silicone Contamination

In 2003 ATK Thiokol discovered that the smocks and coveralls worn by its operations personnel for safety and contamination control were themselves contaminated with a silicone defoamer and a silicone oil. As a growing list of items have been identified as having this form of contamination, it was desirable to devise a test method to determine if the contamination level detected could cause subsequent processing concerns. The smocks and coveralls could potentially contact bonding surfaces during processing so the test method focused on dry transfer of the silicone from the clothing to the bonding surface.

Plaia, James↗

Electrostatic Evaluation: SCAPE Suit Materials

The surface resistivity tests are performed per the requirements of the ESD Association Standard Test Method ESD STM11.11*. These measurements are taken using a PRS-801 resistance system with an Electro Tech System (ETS) PRF-911 concentric ring resistance probe. The tests require a five pound weight on top of cylindrical electrodes and were conducted at both ambient and low humidity conditions. In order for materials to "pass" resistivity tests the surface of the materials must either be conductive or statically dissipative otherwise the materials "fail" ESD. Volume resistivity tests are also conducted to measure conductivity through the material as opposed to conductivity along the surface. These tests are conducted using the same PRS-801 resistance system with the Electro Tech System PRF-911 concentric ring resistance probe but are performed in accordance with ESD Association Standard Test Method ESD STM11.l2**.

Buhler, Charles↗

Full-field Strain Methods for Investigating Failure Mechanisms in Triaxial Braided Composites

Composite materials made with triaxial braid architecture and large tow size carbon fibers are beginning to be used in many applications, including composite aircraft and engine structures. Recent advancements in braiding technology have led to commercially viable manufacturing approaches for making large structures with complex shape. Although the large unit cell size of these materials is an advantage for manufacturing efficiency, the fiber architecture presents some challenges for materials characterization, design, and analysis. In some cases, the static load capability of structures made using these materials has been higher than expected based on material strength properties measured using standard coupon tests. A potential problem with using standard tests methods for these materials is that the unit cell size can be an unacceptably large fraction of the specimen dimensions. More detailed investigation of deformation and failure processes in large unit cell size triaxial braid composites is needed to evaluate the applicability of standard test methods for these materials and to develop alternative testing approaches. In recent years, commercial equipment has become available that enables digital image correlation to be used on a more routine basis for investigation of full field 3D deformation in materials and structures. In this paper, some new techniques that have been developed to investigate local deformation and failure using digital image correlation techniques are presented. The methods were used to measure both local and global strains during standard straight-sided coupon tensile tests on composite materials made with 12 and 24 k yarns and a 0/+60/-60 triaxial braid architecture. Local deformation and failure within fiber bundles was observed, and this local failure had a significant effect on global stiffness and strength. The matrix material had a large effect on local damage initiation for the two matrix materials used in this investigation. Premature failure in regions of the unit cell near the edge of the straight-sided specimens was observed for transverse tensile tests in which the braid axial fibers were perpendicular to the specimen axis and the bias fibers terminated on the cut edges in the specimen gage section. This edge effect is one factor that could contribute to a measured strength that is lower than the actual material strength in a structure without edge effects.

Littell, Justin D.↗

On-Track Measurement of Road Load Changes in Two Close-Following Vehicles: Methods and Results

As emerging automated vehicle technology is making advances in safety and reliability, engineers are also exploring improvements in energy efficiency with this new paradigm. Powertrain efficiency receives due attention, but also impactful is finding ways to reduce driving losses in coordinated-driving scenarios. Efforts focused on simulation to quantify road load improvements require a sufficient amount of background validation work to support them. This study uses a practical approach to directly quantify road load changes by testing the coordinated driving of two vehicles on a test track at various speeds (64, 88, 113 km/h) and vehicle time gaps (0.3 to 1.3 s). Axle torque sensors were used to directly measure the load required to maintain steady-state speeds while following a lead vehicle at various gap distances. Through trial and error, test methods were developed that appear to provide satisfactory results, considering the challenges of track testing under real-world conditions (wind, weather, temperature changes, etc.). We found that total road load was reduced by about 10-12% at an optimum gap time of 0.25 to 0.4 s. Challenges that were encountered included less repeatability of load measurements at short gap distances and powertrain mode switching (from a hybrid vehicle) that rendered the 88-km/h results less useful. This study will provide the framework for further investigations on coordinated-driving road load using track testing methods.

Duoba, Michael↗

Some possible reference materials for fire toxicity tests

Suitable reference materials need to be selected in order to standardize any test method. The evaluation of cotton, polyethylene, polyether sulfone, polycarbonate, polystyrene, and polyurethane flexible and rigid foams as possible reference materials for the University of San Francisco/NASA toxicity screening test method is discussed.

Hilado, C. J.↗

Failure Stress and Apparent Elastic Modulus of Diesel Particulate Filter Ceramics

Three established mechanical test specimen geometries and test methods used to evaluate mechanical properties of brittle materials are adapted to the diesel particulate filter (DPF) architecture to evaluate failure initiation stress and apparent elastic modulus of the ceramics comprising DPFs. The three custom-designed test coupons are harvested out of DPFs to promote a particular combination of orientation of crack initiation and crack plane. The testing of the DPF biaxial flexure disk produces a radial tensile stress and a crack plane parallel with the DPF's longitudinal axis. The testing of the DPF sectored flexural specimen produces axial tension at the DPF's OD and a crack plane perpendicular to the DPF's longitudinal axis. The testing of the DPF o-ring specimen produces hoop tension at the DPF's original outer diameter (OD) and at the inner diameter of the test coupon, and a crack plane parallel to the DPF's longitudinal axis. The testing of these mechanical test coupons also enables the determination of an apparent elastic modulus of the DPF ceramic material. Results consistently show that the apparent elastic modulus of the DPF ceramics is much less (e.g., up to an order of magnitude less) than apparent elastic modulus estimated using sonic- or resonance-based test methods. These specimen geometries, produced stress states, and modes of consequential crack initiation are discussed in context to the DPF's symmetry along with the assessments of each specimen's ease of fabrication, testing, failure stress determination, ultimate viability, and prospects for test standardization. Lastly, an explanation is offered for why the apparent elastic modulus measured with these three mechanical test coupons is relatively low and why their low values are more accurate for predicting thermomechanical stresses in DPFs.

36 MATERIALS SCIENCE↗

A review on snake robot testbeds in granular and restricted maneuverability spaces

Here this article reviews the state of the art in evaluating snake robots for small spaces such as a collapsed building where the snake is either locomoting in restricted maneuverability spaces, such as narrow pipes or tunnels, or pushing through granular regions, such as dirt and rubble. It makes recommendations on designing a testbed that can enable a comprehensive evaluation of a snake robot’s overall capability and an objective comparison of different snakes. A survey of 31 papers reveals that 20 testbeds were used to test snake robots in restricted maneuverability environments. All of those were built specifically to test a particular snake robot rather than for comparison with other snake robots, but each offers insights into designing comprehensive, comparative testbeds. The article analyzed these 20 testbeds in terms of how well they addressed the previously established disaster robotics metrics of scale (a dimensionless number) and four traversability elements, i.e. verticality, tortuosity, accessibility elements, and surface properties. This review suggests that two kinds of general testbeds are in need for the snake robot community: (1) a testbed with high physical fidelity for measuring suitability for a target application, and (2) a testbed which provides a dimensionless comparison of different snake robots. The review is expected to benefit the community in several ways. It can help form a consensus on a suite of metrics and test methods to incorporate into a testbed for evaluating and comparing different types of snake robots and capturing the performance of snake robots in more realistic work envelopes. The metrics and test methods can also pro-actively inform snake robot design as they offer more formally quantified work envelopes, thus accelerating technology transfer. The use of scale and traversability is expected to be applicable to robots in general.

42 ENGINEERING↗