Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Structural components”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

A simple method for modelling fatigue spectra of small wind turbine blades

Small-scale wind turbines have market opportunities in distributed energy generation applications but face future challenges in remaining cost competitive compared with solar photovoltaic systems. High unit costs can be attributed to design conservatism when calculating fatigue loads of key structural components such as the blades. In this study, we use the aeroelastic software FAST to highlight limitations of the International Electrotechnical Commission 61400-2:2013 small wind turbine design standard for calculating fatigue life using the simplified load model. We present a modified method for calculating the fatigue spectra of small wind turbine blades. An advantage of this method is that it does not require complex aeroelastic simulations or field measurements. This modified method is intended to be implemented early in the blade design stage, such as during rotor optimization simulations, allowing for multiple rotor configurations to be rapidly compared.

17 WIND ENERGY↗
DOE OSTI2023

Assessing Manufacturability of the Oxide Dispersion Strengthened (ODS) 14YWT Alloy Fuel Cladding Tube Using SolidStir™ Technology

The 14YWT (Fe–14Cr–3W–0.4Ti–0.3Y2O3 (wt.%)) alloy is a potential candidatematerial for fabricating fuel cladding tubes and other structural components to be used in next-generation advanced nuclear reactors. Due to inherent limitations of current processing routes, this research explored a new variant of friction stir processing, commercially referred to as SolidStir™ Extrusion (patent pending) technology from Enabled Engineering to consolidate and extrude 14YWT powder into a fuel cladding tube. Several single-layer and multiple-layer consolidation experiments were carried out in an Inconel 625 die to determine the suitable processing parameters for SolidStir™ extrusion of the 14YWT alloy cladding tube. With these processing parameters, a 16–18 mm long tube of the 14YWT alloy with no visible defects was successfully extruded using this novel technology. Microstructural characterization results obtained using optical microscopy, scanning electron microscopy, energy dispersive spectroscopy, electron backscatter diffraction, and transmission electron microscopy will be presented.

Advanced Materials and Manufacturing Technology↗
DOE OSTI2023

Compatibility of Wrought Superalloys with Supercritical CO2

Supercritical CO2 (sCO2) power cycles, particularly direct-fired cycles, have the possibility of revolutionizing clean fossil energy with peak temperatures above 700 °C and wrought precipitation strengthened alloys like Haynes 282™ for structural components. At temperatures <650 °C, it would be desirable to use less expensive alloys, however, steels are known to be susceptible to carburization. Laboratory 300 bar sCO2 autoclave results were collected on a range of alloys including less expensive Ni-based alloys like 825 compared to advanced austenitic steels like alloy 709 at 600 °C. Both alloys 825 and 709 formed thin, protective Cr-rich oxides after 1,000 h. Alloy 825 also was exposed for 1,000 h in sCO2 at 800 °C and compared to a range of Ni-based alloys. Comparing alloys 625, 825, and 282, the mass gain increased with increasing alloy Ti content under these conditions. High Al superalloys did not perform significantly better under these conditions at 800 °C.

Pint, Bruce↗
DOE OSTI2023

Small Scale Creep Testing of 14YWT via In-situ Transmission Electron Microscopy Irradiation and Nanoindentation

The next generation of nuclear materials must withstand harsh operating conditions such as high temperatures and irradiation doses. Nanostructured ferritic alloys like oxide dispersion strengthened steels, especially 14YWT, have shown promise as a structural material to withstand these harsh operating conditions. For application, understanding the irradiation enhanced creep of the structural components is fundamental to evaluating the service life in a reactor. Challenges with evaluating irradiation enhanced creep are related to the limited space in nuclear reactors and the expense of conducting post irradiation experiments on irradiated cladding. Ion irradiations are considered to expedite irradiation testing, but such experiments have restricted depth of penetration into the material, limiting the ability to characterize changes to material properties after irradiation. Small scale mechanical testing can be used with ion beam irradiations as a potential avenue to evaluate the irradiation enhanced creep of materials. In this study, in-situ transmission electron microscopy nanopillar creep studies on 14YWT were performed and simultaneously ion beam irradiated with 2.8 MeV Au4+ ions. It was observed that the ion beam irradiation did increase the measured strain rate of the materials. In addition, ex-situ nanoindentation creep studies were performed over a range of temperatures on control 14YWT, and it was observed that there was a change in the deformation mechanism between 873 K and 1073 K that agrees well with macro-scale mechanical testing. Furthermore, these results show promise for applying these techniques to nuclear materials in the future.

14 YWT↗
DOE OSTI2024

Crafting Multifunctional Materials with Tailored Mechanical and Magnetic Properties by Solid-State Non-equilibrium Processing

Aluminum matrix composites hold promise for creating lightweight structural components with multifunctional properties. Nonetheless, achieving desired magnetic or electrical characteristics without compromising their fundamental mechanical properties presents a significant challenge. Here, in this study, we explore mechanical stir-based extrusion as a solid-state metalworking technique to develop fine-grained microstructures and highly refined metallic composites. Our study focuses on creating a SmCo 5 -reinforced aluminum matrix composite using solid stir extrusion (SSE) and assessing its microstructure, mechanical, and magnetic properties through a comprehensive suite of characterization tools, including x-ray diffraction, electron microscopy, and magnetometry. Our findings reveal that incorporating a small amount (3.76 wt.%) of SmCo 5 phase in a non-heat-treatable, non-magnetic aluminum alloy via SSE yields a composite that exhibits good hard magnetic characteristics with a large coercivity (H ci = 13.5 kOe) and improved mechanical properties. This study underscores non-equilibrium processing via solid-state high-speed stirring as a compelling method for crafting multifunctional materials with tailored mechanical and magnetic properties.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Utilization of Hemp Processing Waste for 3D Printing of Biocomposites

Unlike stem biomass, the residues after the extraction of cannabidiol (CBD) oil from hemp flower are challenging to utilize because of their high extractive content (~ 40%, mainly lipids) and are typically considered waste and landfilled. This study presented a novel approach to effectively valorize this underutilized hemp processing waste via chemical processing for three-dimensional (3D) printing applications. Hemp processing waste was processed with sodium hydroxide (NaOH) to control extractives for solving nozzle clogging and then applied as a biofiller in polylactic acid (PLA) composites to improve the mechanical strength. The novelty of this work lies in demonstrating that controlled extractive removal via NaOH treatment not only improves processability but also enhances mechanical performance in 3D-printed biocomposites. We systematically investigated the effect of the processed biofiller content (2.5–10 wt%) on the mechanical and thermal properties of the biocomposites. The decrease in the content of extractives reduced the non-structural components and improved the surface compatibility of the hemp waste with the PLA matrix, thereby enhancing the polymer-biofiller interactions. The best performance was achieved at 2.5 wt% loading, where Young’s modulus increased from 2.3 GPa to 2.6 GPa and tensile strength from 42.7 MPa to 48.8 MPa. Interestingly, the complete removal of extractives also reduced the mechanical strength of their biocomposites, indicating the interfacial adhesion effects of extractives. Furthermore, this study provides new insights into balancing extractive content for optimal mechanical properties, offering a sustainable solution for waste valorization in additive manufacturing.

Additive manufacturing↗
DOE OSTI2021

Accurate Effective Stress Measures: Predicting Creep Life for 3D Stresses Using 2D and 1D Creep Rupture Simulations and Data

Operating structural components experience complex loading conditions resulting in 3D stress states. Current design practice estimates multiaxial creep rupture life by mapping a general state of stress to a uniaxial creep rupture correlation using effective stress measures. The data supporting the development of effective stress measures are nearly always only uniaxial and biaxial, as 3D creep rupture tests are not widely available. This limitation means current effective stress measures must extrapolate from 2D to 3D stress states, potentially introducing extrapolation error. In this work, we use a physics-based, crystal plasticity finite element model to simulate uniaxial, biaxial, and triaxial creep rupture. Here, we use the virtual dataset to assess the accuracy of current and novel effective stress measures in extrapolating from 2D to 3D stresses and also explore how the predictive accuracy of the effective stress measures might change if experimental 3D rupture data was available. We confirm these conclusions, based on simulation data, against multiaxial creep rupture experimental data for several materials, drawn from the literature. The results of the virtual experiments show that calibrating effective stress measures using triaxial test data would significantly improve accuracy and that some effective stress measures are more accurate than others, particularly for highly triaxial stress states. Results obtained using experimental data confirm the numerical findings and suggest that a unified effective stress measure should include an explicit dependence on the first stress invariant, the maximum tensile principal stress, and the von Mises stress.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Exascale granular microstructure reconstruction in 3D volumes of arbitrary geometries with generative learning

Reconstructing 3D granular microstructures within volumes of arbitrary geometries from limited 2D image data is crucial for predicting the material properties, as well as performances of structural components accounting for material microstructural effects. We present a novel generative learning framework that enables exascale reconstruction of granular microstructures within complex 3D geometric volumes. Building upon existing transfer learning techniques using pre-trained convolutional neural networks (CNN), we introduce several key innovations to overcome the difficulties inherent in arbitrary geometries. Our framework incorporates periodic boundary conditions using circular padding techniques, ensuring continuity and representativeness of the reconstructed microstructures. We also introduce a novel seamless transition reconstruction (STR) method that creates statistically equivalent transition zones to integrate multiple pre-existing 3D microstructure volumes. Based on STR, we propose a cost-effective strategy for reconstructing microstructures within complex geometric volumes, minimizing computational waste. Validation through numerical experiments using kinetic Monte Carlo simulations demonstrates accurate reproduction of grain statistics, including grain size distributions and morphology. A case study involving the reconstruction of a 4-blade propeller microstructure illustrates the method’s capability to efficiently handle complex geometries. In conclusion, the proposed framework significantly reduces computational demands while maintaining high reconstruction quality, paving the way for scalable microstructure reconstruction in materials design and analysis.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Mechanical Characterization of High-Temperature Carbon Fiber-Polyphenylene Sulfide Composites for Large Area Extrusion Deposition Additive Manufacturing

Additive manufacturing (AM) is evolving from rapid prototyping to production of structural components. The widespread application of AM demands a high level of mechanical performance from these components, and it is therefore essential to improve feedstock material in order to meet these mechanical expectations. However, compared to traditional manufacturing techniques, the mechanical properties of AM materials and their resulting components are not well understood. In this study, we investigated the processability, microstructure, and mechanical performance of twin-screw compounded short carbon fiber reinforced polyphenylene sulfide (PPS) pellets as a feedstock material for big area AM (BAAM). The performance of the AM components was compared to that of traditional processing methods, namely injection molding (IM) and extrusion-compression molding (ECM). It was found that the AM composites exhibited 118% lower tensile strength and 55% lower tensile modulus when compared to traditional injection molding composite specimens; however, AM composites exhibited comparable properties to ECM composites. This response was attributed to highly aligned fibers in IM and AM samples. However, the AM composites contained porosity (15.5% volume), which reduced their mechanical properties in comparison to ECM composites. Finally, the IM process showed the maximum amount of fiber attrition with minimum porosity (0.007% volume), while the ECM process exhibited the least fiber attrition with 4.3% volume porosity.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Reproducible benchmark for the SNAP 8 experimental reactor at dry conditions

Here, this work provides fully reproducible benchmark models of the Systems for Nuclear Auxiliary Power (SNAP) 8 Experimental Reactor. Validation benchmarks of the criticality configuration experiments under dry conditions with no coolant are presented. In addition, relevant reactivity worth experiments, and measurement of power distributions are validated and presented here. Discrepancies between modeled and experimental results are at most 110 pcm for fuel and poison worths, and critical configurations that do not manipulate control elements are within 50 pcm. Larger discrepancies found in reflector element worth experiments are due to experimental methodology which was noted as being simplified due to limited calculational capabilities at the time, while discrepancy in the control element manipulated critical configuration is due the absence of structural components for modeling simplification. Power distributions closely follow what was observed in experiment with expected peaking in reflecting elements. All models are well documented with cited references describing and justifying assumptions, simplifications, and adjustments to reproduce the models with any nuclear safety codes; model inputs and outputs are stored in the snapReactors GitHub repository.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2021

Ab-initio investigation of the effect of adsorbed salts on segregation of Cr at the Ni (100) surface

The dissolution and depletion of chromium (Cr) in salt facing nickel (Ni) alloy surfaces is one of the predominant degradation mechanisms of structural components in molten salt technology. Here, we use density functional theory to investigate the role of electronic level interactions that may underlie the depletion phenomenon of Cr in a Ni (100) surface exposed to various adsorbed salt species. Our results show that, under vacuum, Ni preferentially segregates to the surface layer. Conversely, in the presence of adsorbed anionic salt species (e.g., chlorine (Cl), fluorine (F) or the impurity oxygen (O)) Cr segregation becomes more favorable. In these cases, Cl has the weakest effect on segregation, while O has the strongest effect. Our analysis reveals the strong correlation between Cr segregation and the amount of valence charge transferred between the Cr atom and surface adsorbate: the greater the charge transfer, the lower the segregation energy. We also show that, when considered, secondary cations screen Cr-anion interactions, which in turn reduce the magnitude of the anions effect on segregation. These results shed light on the role of salt impurities likely play in the overall corrosion phenomena in molten salt environments. This work provides insights into the atomic level interactions fundamental to molten salt corrosion and on the importance of maintaining salt purity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Plasma treatment on both adhesive tape and adherends for significantly enhanced CFRTP-related adhesive joints

Unlike existing literature that primarily concentrates on either the plasma treatment of adherends alone or solely on adhesive surfaces, this work leverages plasma modification of both adhesive in tape form and adherend surfaces to largely enhance the interfacial bonding between a thermoset-based adhesive tape and carbon-fiber-reinforced thermoplastic polymer (CFRTP) for structural bonding applications. Here, by conducting single lap shear tests on adhesively-bonded AA6061-CFRPPA (carbon-fiber-reinforced polyphthalamide) dissimilar joints, it is shown that the plasma treatment of adherends alone can increase the lap shear strength (LSS) of the joints by approximately 200% compared to non-treated counterparts. An additional plasma treatment of adhesive tape surfaces leads to even higher LSS improvement, reaching up to 315%, due to the formation of a denser crosslinked network of covalent bonds and a reduced area fraction of interfacial voids at the CFRPPA/adhesive interface. The highest plasma-enhanced LSS of the metal-CFRTP dissimilar joints rivals that of metal-metal joints, which is typically stronger than the joints associated with fiber-reinforced polymers. This study is important for achieving strong CFRTP-related structural components bonded using adhesive tape, providing better compatibility with plasma treatment and other joining methods like riveting compared to adhesive paste or liquid.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A multiscale cohesive law for carbon fiber networks

Better predictive models of mechanical failure in low-weight heat shield composites would aid material certification for missions with aggressive atmospheric entry conditions. In this study, we develop such a model for the rapid engineering analysis of the failure limits of phenolic impregnated carbon ablator (PICA) - a leading heat shield material whose structural component is a carbon fiber network. We hypothesize inelastic deformation failure mechanisms and model their behavior using molecular dynamics simulations to calculate the binding energy. We then upscale this binding energy to the macroscale using a renormalization argument. The approach delivers insightful and reasonably accurate macroscale predictions that compare favorably to experiments. In application, the model is validated for a particular variety of PICA by comparison to experiment and would then be used to study design scenarios in different entry conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Mode I tensile fracture behavior of adhesively-bonded metal–metal, metal–CFRP, and CFRP–CFRP bi-material combinations analyzed by size effect method

Understanding the adhesive and interfacial fracture is important for developing and achieving better adhesive jointing in bi-materials, the location which becomes less vulnerable in engineered structure components. Still, to characterize the fracturing behavior of various adhesively-bonded materials, it was shown in this work that the Mode I fracture energies estimated from conventional methods (e.g., work-of-fracture, (modified) compliance calibration method, (modified) beam theory, etc.) can be strongly affected by adherent thickness, adhesive bond length, and material type. Consequently, this hindered the proper understanding of fracturing in adhesive jointing of bi-materials since the estimated fracture energies can exhibit unreasonable difference among various material combinations, thus leading to the confusion in the literature due to the unfair comparison on these non-objective results estimated by leveraging conventional methods on the specimens with different geometries. This work compared size effect method with conventional methods on the calculation of the Mode I fracture energies of metal-metal, metal-CFRP, and CFRP-CFRP material combinations via Double Cantilever Beam (DCB) tests. The results showed that the estimated fracture energies of various material combinations are not dependent on the specimen geometries. This aspect allowed the fair comparison particularly on the interfacial fracturing between metal/adhesive and CFRP/adhesive, and the difference was further explained and correlated with the damage morphology on the material surface after failure identified through three-dimensional profilometer.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Validation of process simulation workflow for thermosetting prepreg platelet molding compounds

Continuous carbon fiber prepreg slit and cut into rectangular platelets has proven to be a useful material for net shape molding of semi-structural and structural components in the aerospace and automotive industries. Furthermore, to assist the designer in use of these prepreg platelet molding compounds, sometimes called carbon fiber sheet molding compounds, simulation tools are required that can predict the as-manufactured fiber orientation state which has a significant impact on the resulting performance. Herein, an analysis workflow for design-enabling predictions is demonstrated for a double dome geometry with two different initial charge configurations. Here, the workflow is validated through comparison with experimental short shots, orientation state, and stiffness trends. Significantly, to complete the validation, a method is proposed for determining the confidence bounds on measured orientation state enhancing the results of optical microscopy which can only produce a small sample of platelet orientations.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Multifunctional approaches for safe structural batteries

Recent advancements in Li and Li-ion based energy storage resulted in development of novel electrode materials for higher energy density which are finding their applications in transportation. There appears to be a limitation in improvement of specific energy of the system based solely on design of material compositions for multivalent intercalation compounds. In addition, higher energy stored by the system implies need for addressing safety concerns especially when it comes to large automotive battery packs. New approaches for improvement of both energy density and safety of batteries are emerging, where multifunctionality of the materials and/or architectures is utilized. Here, we present a review for such approaches from multifunctional current collectors to design of batteries capable of supporting mechanical loads and thus possessing ability to be used as a structural component.

25 ENERGY STORAGE↗
DOE OSTI2020

Determination of preferential binder oxidation in HTGR matrix material subjected to high temperature steam

Graphitic matrix material encapsulates tristructural isotropic (TRISO) coated fuel particles and is a structural component for both pebble and cylindrical fuel compacts in high temperature gas reactor (HTGR) designs. In an off-normal event involving steam exposure, the matrix material is exposed to oxidants, leading to degradation of the fuel compact and subsequent exposure of the TRISO particle fuel to oxidizing species. This study presents microstructural characterization of matrix material after exposure to high temperature (1200°C), 48 kPa steam in which the evolved microstructure demonstrated nonuniform degradation. Subsequent Raman spectroscopy determined the nature of the remaining material post-exposure. Finally, the electron microscopy characterization suggests and Raman spectroscopic analysis confirms, under off-normal conditions, the carbonized phenolic resin binder is preferentially oxidized ahead of the graphite flake filler and is responsible for the nonuniform degradation and enhanced depth of attack.

36 MATERIALS SCIENCE↗
DOE OSTI2021

First steps toward predicting corrosion behavior of structural materials in molten salts

To address the need for physics-based models to predict corrosion behavior of materials in molten salts, here we propose potential methods to aid in selection of optimum materials for structural components in molten salt powered technologies. In the present work, the role of alloy thermodynamics and kinetics on governing corrosion rates of Ni-based alloys will be discussed combining experimental and computational methods. A few strategies are presented to quantify corrosion rates of Ni-based materials isothermally exposed in purified KCl-MgCl 2 salts at 600° C-800° C. The influence of capsule material, potential corrosion products and role of alloy composition on the observed corrosion rates was discussed with coupled thermodynamic-kinetic models. Larger depths of corrosion attack were observed in alloy 230 specimens compared to other alloys under similar conditions was attributed to the much higher chemical activity of Cr in the alloy that results in a larger Cr chemical potential gradient.

36 MATERIALS SCIENCE↗