Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SiC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

Thermal expansion of 4H and 6H SiC from 5 K to 340 K

The first thermal expansion measurements of the 4H and 6H polytypes of SiC below room temperature are reported. The measurements were carried out on single-crystal specimens using high-resolution capacitive-based dilatometry. For both polytypes, the thermal expansion coefficient is below 2.4 × 10 -6 1/K near room temperature. No phase transitions are observed over the 5 K to 340 K temperature range of the measurements. The thermal expansion coefficient α of 4H SiC is slightly anisotropic for measurements parallel and perpendicular to the crystallographic c axis with α ∥ about 2.2 × 10 -7 1/K larger than α ⟂ near room temperature. For 6H SiC no discernible anisotropy is observed. The differences in anisotropy can be understood by considering the ratio of hexagonal to cubic bonds of each polytype. Narrow regions with negative thermal expansion that are within the limits of our resolution (~ 1 x 10 -8 ) are observed in the vicinity of 30 K for both specimens. In conclusion, tabulated data, polynomial fits, fit parameters, and comparison to data based on lattice-parameter measurements are provided.

36 MATERIALS SCIENCE↗

Hydrogen activated axial inter-conversion in SiC nanowires

A facile low pressure annealing route using NH{sub 3} as a hydrogen source for the structural and chemical modification of SiC nanowires (SiCNWs) is presented. The developed route transforms SiCNWs into tubular SiC nanostructures while coaxial SiO{sub 2}/SiCNWs reverse their sheath/core structure. Our findings suggest a decomposition process induced via the preferential substitution of silicon by hydrogen and via the difference in diffusion rates of available atomic species, which leads to axial structural rearrangement. In addition to these effects, the procedure improves the crystallinity of the samples. The process could be exploited as a viable route to manipulate a variety of nanostructures and films for doping and etching and structural manipulation. - Graphical abstract: SiC and SiO{sub 2}/SiCNWs are shown to be structurally modified through a hydrogen activated replacement route which can even lead to the axial inter-conversion of species. The process could be exploited as a viable route to manipulate a variety of nanostructures and films for doping and etching and structural manipulation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A TEM quantitative evaluation of strengthening in an Mg-RE alloy reinforced with SiC

Magnesium alloys containing rare earth elements are known to have high specific strength, good creep and corrosion resistance up to 523 K. The addition of SiC ceramic particles strengthens the metal matrix composite resulting in better wear and creep resistance while maintaining good machinability. The role of the reinforcement particles in enhancing strength can be quantitatively evaluated using transmission electron microscopy (TEM). This paper presents a quantitative evaluation of the different strengthening contributions, determined through TEM inspections, in an SiC Mg-RE composite alloy containing yttrium, neodymium, gadolinium and dysprosium. Compression tests at temperatures ranging between 290 and 573 K were carried out. The microstructure strengthening mechanism was studied for all the compression conditions. Strengthening was compared to the mechanical results and the way the different contributions were combined is also discussed and justified. - Research Highlights: {yields} TEM yield strengthening terms evaluation on a Mg-RE SiC alloy. {yields} The evaluation has been extended to different compression temperature conditions. {yields} Linear and Quadratic sum has been proposed and validated. {yields} Hall-Petch was found to be the most prominent strengthening contributions.

36 MATERIALS SCIENCE↗

Tailoring the interfacial microstructure and mechanical strength of SiC ceramic joints using joining temperature and interlayer thickness

Highlights: • Bonding temperature could be decreased from 1600 °C to 1300 °C by inserting the Ti foil between SiC and Ta-5W. • The initial thickness interlayer and the number of interlayer had a significant influence on interface bonding. • Layered reaction layers consisting of carbides and silicide formed at the SiC/Ti/Ta-5W interfaces. • The joint strength depended mainly on the reaction layer thickness, especially the thickness of silicide layer. - Abstract: Silicon carbide ceramic joints solid state diffusion bonded by spark plasma sintering with Ti/Ta-5W/Ti multi-interlayer in the temperature range from 1250 °C to 1500 °C were investigated in detail in terms of interfacial microstructure, elemental diffusion, phase constituents, shear strength, and fracture morphology. Layered reaction layers consisting of carbides (TiC, Ti{sub 3}SiC{sub 2}, (Ta,Ti,W)C), silicide ((Ta,Ti,W){sub 5}Si{sub 3}) and Ta-rich solid solution (Ta,Ti,W) formed at the SiC/Ti/Ta-5W interfaces. It was found that joining temperature could be decreased from 1600 °C to 1300 °C by inserting the Ti foil between SiC and Ta-5W. Nevertheless, an attempt to further decrease the joining temperature to 1250 °C failed even using a thin Ti foil. The initial thickness interlayer and the number of interlayer had an influence on the interfacial diffusion bonding at SiC/Ti interface. Higher joining temperature was needed to achieve a tough interface joining for a thick interlayer compared with a thin interlayer. The increase of interlayer number also required higher joining temperature. The shear strength reached 123.5 ± 25.3 MPa for the joint diffusion bonded at 1300 °C.

36 MATERIALS SCIENCE↗

Synthesis of nanostructured SiC using the pulsed laser deposition technique

We report the new results on the direct synthesis of nanostructured silicon carbide (SiC) materials using the pulsed laser deposition technique. Scanning electron microscopy images revealed that SiC nanoholes, nanosprouts, nanowires, and nanoneedles were obtained. The crystallographic structure, chemical composition, and bond structure of the nanoscale SiC materials were investigated using X-ray diffraction, energy dispersive X-ray spectroscopy, X-ray photoelectron spectroscopy, and Raman scattering spectroscopy. The transverse optical mode and longitudinal optical mode in Raman spectra were found to become sharper as the substrate temperature was increased, while the material structure evolved from amorphous to crystalline.

36 MATERIALS SCIENCE↗

Epitaxial growth of SnO{sub 2} films on 6H-SiC (0 0 0 1) by MOCVD

Highlights: Black-Right-Pointing-Pointer Heteroepitaxial SnO{sub 2} films have been successfully deposited on 6H-SiC (0 0 0 1) substrates. Black-Right-Pointing-Pointer We propose a growth model that SnO{sub 2} films consist of three domains with equivalent in-plane orientations. Black-Right-Pointing-Pointer The electrical properties of SnO{sub 2} films are in consistent with the structure analysis. -- Abstract: SnO{sub 2} films have been deposited on 6H-SiC (0 0 0 1) substrates by metalorganic chemical vapor deposition in the temperature range 500-750 Degree-Sign C. X-ray diffraction analysis showed that all the films were highly (1 0 0) oriented with the tetragonal rutile structure. Based on the structure analysis, we propose a growth model that SnO{sub 2} films consist of three variant structures with equivalent in-plane orientations. The in-plane orientation relationship between SnO{sub 2} and 6H-SiC was determined to be SnO{sub 2} [0 1 0]//SiC <101{sup Macron }0> and SnO{sub 2} [0 0 1]//SiC <12{sup Macron }10>. As the substrate temperature increased from 500 to 750 Degree-Sign C, the carrier concentration decreased from 1.1 Multiplication-Sign 10{sup 20} to 1.6 Multiplication-Sign 10{sup 18} cm{sup -3} while the resistivity increased from 0.01 to 0.57 {Omega} cm.

36 MATERIALS SCIENCE↗

Reactive sintering of tungsten-doped high strength ZrB{sub 2}–SiC porous ceramics using metastable precursors

Graphical abstract: - Highlights: • Tungsten-doped porous ZrB{sub 2}–SiC specimens were fabricated by reactive sintering. • Both sintering and mechanical properties were improved by doping with tungsten. • Optimum concentration to obtain high mechanical properties was W/Zr (mol) = 0.05. • Sintering might be promoted by self-accelerated diffusion. • Mechanical properties might be improved by solid solution strengthening. - Abstract: Tungsten-doped porous ZrB{sub 2}-20 vol.% SiC specimens with a high strength skeleton were fabricated by reactive sintering using metastable reactants, i.e., as-synthesized amorphous hydrous ZrO{sub 2}–WO{sub 3}/ZrO{sub 2}, amorphous boron, nanocarbon, and β-SiC. Doping with tungsten clearly promoted sintering and improved mechanical properties; the optimum tungsten concentration to obtain high mechanical properties was investigated. A single-phase solid solution (Zr,W)B{sub 2} was formed in the specimens with tungsten. We suggest that sintering was promoted by self-accelerated diffusion owing to the formation of point defects caused by doping with tungsten. The improvement of mechanical properties could be attributed to solid solution strengthening.

36 MATERIALS SCIENCE↗

Formation and properties of defects and small vacancy clusters in SiC: Ab initio calculations

Large-scale ab initio simulation methods have been employed to investigate the configurations and properties of defects in SiC. Atomic structures, formation energies and binding energies of small vacancy clusters have also been studied as a function of cluster size, and their relative stabilities are determined. The calculated formation energies of point defects are in good agreement with previously theoretical calculations. The results show that the most stable configuration of a di-vacancy cluster consists of two C vacancies located at second nearest neighbor sites, while a di-vacancy with two Si vacancies is not stable and may dissociate at room temperature. In general, the formation energies of small vacancy clusters increase with size, but the formation energies for clusters with a Si vacancy and n C vacancies (VSi-nVC) are much smaller than those with a C vacancy and n Si vacancies (VC-nVSi). These results demonstrate that the VSi-nVC clusters are more stable than the VC-nVSi clusters in SiC, and provide possible nucleation sites for larger vacancy clusters or voids to grow. For these small vacancy clusters, the binding energy decreases with increasing cluster size, and ranges from 2.5 to 4.6 eV. These results indicate that the small vacancy clusters in SiC are stable at temperatures up to 1900 K, which is consistent with experimental observations.

36 MATERIALS SCIENCE↗

Processing and microstructure of ZrB 2 –SiC composite prepared by reactive spark plasma sintering

In-situ formation of ZrB 2 –SiC composites was investigated by reactive spark plasma sintering of precursor powders according to the reaction B4C + 2ZrC + 3Si → 3SiC + 2ZrB 2 . The reaction and process presented here involves a diffusion reaction between B4C and ZrC which facilitates the formation of ZrB 2 , while liquid phase sintering of silicon facilitates atomic diffusion and combines with free C from the B4C and ZrC reaction to form SiC within minutes of heating and there were some residual unreacted precursor materials. An interpenetrating matrix of ZrB 2 –SiC was formed that shows increased fracture toughness (6.03 ± 0.45 MPa m 1/2 ) despite relatively low density (95 %).

36 MATERIALS SCIENCE↗

Experimental evaluation of direct current magnetron sputtered and high-power impulse magnetron sputtered Cr coatings on SiC for light water reactor applications

Two types of physical vapor deposition Cr coatings were deposited on chemical vapor deposited SiC coupons using conventional direct current magnetron sputtering (DCMS) and high-power impulse magnetron sputtering (HiPIMS) to mitigate the corrosion of SiC, an advanced fuel and structural material in light water nuclear reactor cores. Coating microstructure was characterized using scanning electron microscopy and scanning transmission election microscopy. X-ray diffraction analysis was conducted for phase identification and qualitative analysis of residual stresses. The mechanical integrity of the coatings was evaluated using scratch testing, micro-indentation, and nano-indentation tests. Additionally, the microstructure of the DCMS coating consisted of fine columnar grains with nanoscale intercolumnar channels, while the HiPIMS microstructure was denser and free of any columnar defects. The DCMS coating showed a small tensile residual stress, while the HiPIMS coating was under compressive stress. Both types of coatings showed good mechanical integrity in terms of ductility and adhesion to the substrate. Corrosion performance of the coatings was assessed with a 30-day high temperature water autoclave test. Both types of coatings formed a protective Cr 2 O 3 surface layer 20-30 nm thick during the autoclave test. In the DCMS coating, the columnar defects provided permeation pathways for water penetration resulting in oxide formation in the intercolumnar regions in the interior of the coating. Overall, both types of Cr coatings offer promise for the mitigation of hydrothermal corrosion of SiC in light water reactor operating environments.

36 MATERIALS SCIENCE↗

Layer-by-Layer Transfer of Multiple, Large Area Sheets of Graphene Grown in Multilayer Stacks on a Single SiC Wafer

Here we report a technique for transferring graphene layers, one by one, from a multilayer deposit formed by epitaxial growth on the Si-terminated face of a 6H-SiC substrate. The procedure uses a bilayer film of palladium/polyimide deposited onto the graphene coated SiC, which is then mechanically peeled away and placed on a target substrate. Orthogonal etching of the palladium and polyimide leaves isolated sheets of graphene with sizes of square centimeters. Repeating these steps transfers additional sheets from the same SiC substrate. Raman spectroscopy, scanning tunneling spectroscopy, low-energy electron diffraction and X-ray photoelectron spectroscopy, together with scanning tunneling, atomic force, optical, and scanning electron microscopy reveal key properties of the materials. The sheet resistances determined from measurements of four point probe devices were found to be ~2 kΩ/square, close to expectation. As a result, graphene crossbar structures fabricated in stacked configurations demonstrate the versatility of the procedures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Optical charge state control of spin defects in 4H-SiC

Defects in silicon carbide (SiC) have emerged as a favorable platform for optically active spin-based quantum technologies. Spin qubits exist in specific charge states of these defects, where the ability to control these states can provide enhanced spin-dependent readout and long-term charge stability. We investigate this charge state control for two major spin qubits in 4H-SiC, the divacancy and silicon vacancy, obtaining bidirectional optical charge conversion between the bright and dark states of these defects. We measure increased photoluminescence from divacancy ensembles by up to three orders of magnitude using near-ultraviolet excitation, depending on the substrate, and without degrading the electron spin coherence time. This charge conversion remains stable for hours at cryogenic temperatures, allowing spatial and persistent patterning of the charge state populations. As a result, we develop a comprehensive model of the defects and optical processes involved, offering a strong basis to improve material design and to develop quantum applications in SiC.

36 MATERIALS SCIENCE↗

Thermodynamics and electronic structure of adsorbed and intercalated plumbene in graphene/hexagonal SiC heterostructures

Abstract Graphene-covered hexagonal SiC substrates have been frequently discussed to be appropriate starting points for epitaxial overlayers of Xenes, such as plumbene, or even their deposition as intercalates between graphene and SiC. Here, we investigate, within density functional theory, the plumbene deposition for various layer orderings and substrate terminations. By means of total energy studies we demonstrate the favorization of the intercalation versus the epitaxy for both C-terminated and Si-terminated 4H-SiC substrates. These results are explained in terms of chemical bonding and by means of layer-resolved projected band structures. Our results are compared with available experimental findings.

Science & Technology - Other Topics↗

Controlling the defects and transition layer in SiO 2 films grown on 4 H -SiC via direct plasma-assisted oxidation

The structural stability and electrical performance of SiO 2 grown on SiC via direct plasma-assisted oxidation were investigated. To investigate the changes in the electronic structure and electrical characteristics caused by the interfacial reaction between the SiO 2 film (thickness ~ 5 nm) and SiC, X-ray photoelectron spectroscopy (XPS), X-ray absorption spectroscopy (XAS), density functional theory (DFT) calculations, and electrical measurements were performed. The SiO 2 films grown via direct plasma-assisted oxidation at room temperature for 300s exhibited significantly decreased concentrations of silicon oxycarbides (SiO x C y ) in the transition layer compared to that of conventionally grown (i.e., thermally grown) SiO 2 films. Moreover, the plasma-assisted SiO 2 films exhibited enhanced electrical characteristics, such as reduced frequency dispersion, hysteresis, and interface trap density ( D it ≈ 10 11 cm -2 · eV -1 ). In particular, stress induced leakage current (SILC) characteristics showed that the generation of defect states can be dramatically suppressed in metal oxide semiconductor (MOS) structures with plasma-assisted oxide layer due to the formation of stable Si-O bonds and the reduced concentrations of SiO x C y species defect states in the transition layer. That is, energetically stable interfacial states of high quality SiO 2 on SiC can be obtained by the controlling the formation of SiO x C y through the highly reactive direct plasma-assisted oxidation process.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effects of collision cascade density on radiation defect dynamics in 3C-SiC

Effects of the collision cascade density on radiation damage in SiC remain poorly understood. We study damage buildup and defect interaction dynamics in 3C-SiC bombarded at 100 °C with either continuous or pulsed beams of 500 keV Ne, Ar, Kr, or Xe ions. Here, we find that bombardment with heavier ions, which create denser collision cascades, results in a decrease in the dynamic annealing efficiency and an increase in both the amorphization cross-section constant and the time constant of dynamic annealing. The cascade density behavior of these parameters is non-linear and appears to be uncorrelated. Our results demonstrate clearly (and quantitatively) an important role of the collision cascade density in dynamic radiation defect processes in 3C-SiC.

36 MATERIALS SCIENCE↗

Pitfalls in parameters: practical process development in chemical vapor processing of SiC

Vapor processing of high-value materials, such as silicon carbide (SiC), is of interest for many industries, including aerospace and energy production. Chemical vapor infiltration (CVI) of additively manufactured components is an especially attractive manufacturing process currently in development. Here, a novel development workflow is demonstrated with the H 2 –CH 3 SiCl 3 gas system for SiC to accelerate the process optimization of CVI SiC. A combination of calculated thermodynamics and high-throughput experimental chemical vapor deposition (CVD) coatings substantially reduced the experiments required with slow CVI processes. The computational results accurately predicted changes in the thermodynamic conditions tested, while CVD coatings – characterized by Raman spectroscopy – addressed changes in kinetic parameters. This workflow is also applicable to other vapor-processing systems, such as pyrolytic carbon, ZrC, or Si 3 N 4 .

Lamm, Benjamin W. [Oak Ridge National Laboratory (↗

Amorphization and dynamic annealing of hexagonal SiC upon heavy-ion irradiation: Effects on swelling and mechanical properties

Structural, mechanical, and dimensional evolutions of silicon carbide (SiC) induced by heavy-ion irradiations are studied by means of Rutherford backscattering spectrometry and channeling (RBS/C), nanoindentation, and surface profilometry measurements. 4H- and 6H-SiC single crystals were irradiated with 4 MeV Au{sup 2+} and 4 MeV Xe{sup +} ions at room temperature (RT) or 400 deg. C. Using a Monte Carlo program to simulate the RBS/C spectra (MCCHASY code), we find that Au ion irradiation at RT induces a total silicon sublattice disorder related to full amorphization at a dose of about 0.4 displacement per atom (dpa). A two-step damage process is found on the basis of the disordered fractions deduced from RBS/C data. Complete amorphization cannot be reached upon both Au and Xe ion irradiations at 400 deg. C up to about 26 dpa because of the dynamic annealing of defects. When complete amorphization is reached at RT, the Young's modulus and Berkovich hardness of irradiated 6H-SiC samples are lower by, respectively, 40% and 45% than those of the virgin crystals. The out-of-plane expansion measured by surface profilometry increases versus irradiation dose and the saturation value measured in the completely amorphous layer (normalized to the ion projected range) is close to 25%. We show that the modifications of the macroscopic properties are mainly due to the amorphization of the material. The macroscopic elasticity constants and dimensional properties are predicted for a composite material made of crystalline matrix containing dispersed amorphous inclusions using simple analytical homogenization models. Voigt's model seems to give the best approximation for disordered fractions larger than 20% in the second step of the damage process.

36 MATERIALS SCIENCE↗

SIC-POVMS and MUBS: Geometrical Relationships in Prime Dimension

The paper concerns Weyl-Heisenberg covariant SIC-POVMs (symmetric informationally complete positive operator valued measures) and full sets of MUBs (mutually unbiased bases) in prime dimension. When represented as vectors in generalized Bloch space a SIC-POVM forms a d{sup 2}-1 dimensional regular simplex (d being the Hilbert space dimension). By contrast, the generalized Bloch vectors representing a full set of MUBs form d+1 mutually orthogonal d-1 dimensional regular simplices. In this paper we show that, in the Weyl-Heisenberg case, there are some simple geometrical relationships between the single SIC-POVM simplex and the d+1 MUB simplices. We go on to give geometrical interpretations of the minimum uncertainty states introduced by Wootters and Sussman, and by Appleby, Dang and Fuchs, and of the fiduciality condition given by Appleby, Dang and Fuchs.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗