Results for “Shear Layers” — Page 38

NASA NTRS2015

Investigation of Unsteady Tip Clearance Flow in a Low-Speed One and Half Stage Axial Compressor with LES And PIV

The primary focus of this paper is to investigate how a rotor's unsteady tip clearance flow structure changes in a low speed one and half stage axial compressor when the rotor tip gap size is increased from 0.5 mm (0.49% of rotor tip blade chord, 2% of blade span) to 2.4 mm (2.34% chord, 4% span) at the design condition are investigated. The changes in unsteady tip clearance flow with the 0.62 % tip gap as the flow rate is reduced to near stall condition are also investigated. A Large Eddy Simulation (LES) is applied to calculate the unsteady flow field at these three flow conditions. Detailed Stereoscopic PIV (SPIV) measurements of the current flow fields were also performed at the Johns Hopkins University in a refractive index-matched test facility which renders the compressor blades and casing optically transparent. With this setup, the unsteady velocity field in the entire flow domain, including the flow inside the tip gap, can be measured. Unsteady tip clearance flow fields from LES are compared with the PIV measurements and both LES and PIV results are used to study changes in tip clearance flow structures. The current study shows that the tip clearance vortex is not a single structure as traditionally perceived. The tip clearance vortex is formed by multiple interlaced vorticities. Therefore, the tip clearance vortex is inherently unsteady. The multiple interlaced vortices never roll up to form a single structure. When phased-averaged, the tip clearance vortex appears as a single structure. When flow rate is reduced with the same tip gap, the tip clearance vortex rolls further upstream and the tip clearance vortex moves further radially inward and away from the suction side of the blade. When the tip gap size is increased at the design flow condition, the overall tip clearance vortex becomes stronger and it stays closer to the blade suction side and the vortex core extends all the way to the exit of the blade passage. Measured and calculated unsteady flow fields inside the tip gap agree fairly well. Instantaneous velocity vectors inside the tip gap from both the PIV and LES do show flow separation and reattachment at the entrance of tip gap as some earlier studies suggested. This area at the entrance of tip gap flow (the pressure side of the blade) is confined very close to the rotor tip section. With a small tip gap (0.5mm), the gap flow looks like a simple two-dimensional channel flow with larger velocity near the casing for both flow rates. A small area with a sharp velocity gradient is observed just above the rotor tip. This strong shear layer is turned radially inward when it collides with the incoming flow and forms the core structure of the tip clearance vortex. When tip gap size is increased to 2.4 mm at the design operation, the radial profile of the tip gap flow changes drastically. With the large tip gap, the gap flow looks like a two-dimensional channel flow only near the casing. Near the rotor top section, a bigger region with very large shear and reversed flow is observed.

compressor↗

NASA NTRS2015

Investigation of Unsteady Tip Clearance Flow in a Low-Speed One and Half Stage Axial Compressor with LES And PIV

The primary focus of this paper is to investigate how a rotor's unsteady tip clearance flow structure changes in a low speed one and half stage axial compressor when the rotor tip gap size is increased from 0.5 mm (0.49% of rotor tip blade chord, 2% of blade span) to 2.4 mm (2.34% chord, 4% span) at the design condition are investigated. The changes in unsteady tip clearance flow with the 0.62 % tip gap as the flow rate is reduced to near stall condition are also investigated. A Large Eddy Simulation (LES) is applied to calculate the unsteady flow field at these three flow conditions. Detailed Stereoscopic PIV (SPIV) measurements of the current flow fields were also performed at the Johns Hopkins University in a refractive index-matched test facility which renders the compressor blades and casing optically transparent. With this setup, the unsteady velocity field in the entire flow domain, including the flow inside the tip gap, can be measured. Unsteady tip clearance flow fields from LES are compared with the PIV measurements and both LES and PIV results are used to study changes in tip clearance flow structures. The current study shows that the tip clearance vortex is not a single structure as traditionally perceived. The tip clearance vortex is formed by multiple interlaced vorticities. Therefore, the tip clearance vortex is inherently unsteady. The multiple interlaced vortices never roll up to form a single structure. When phased-averaged, the tip clearance vortex appears as a single structure. When flow rate is reduced with the same tip gap, the tip clearance vortex rolls further upstream and the tip clearance vortex moves further radially inward and away from the suction side of the blade. When the tip gap size is increased at the design flow condition, the overall tip clearance vortex becomes stronger and it stays closer to the blade suction side and the vortex core extends all the way to the exit of the blade passage. Measured and calculated unsteady flow fields inside the tip gap agree fairly well. Instantaneous velocity vectors inside the tip gap from both the PIV and LES do show flow separation and reattachment at the entrance of tip gap as some earlier studies suggested. This area at the entrance of tip gap flow (the pressure side of the blade) is confined very close to the rotor tip section. With a small tip gap (0.5mm), the gap flow looks like a simple two-dimensional channel flow with larger velocity near the casing for both flow rates. A small area with a sharp velocity gradient is observed just above the rotor tip. This strong shear layer is turned radially inward when it collides with the incoming flow and forms the core structure of the tip clearance vortex. When tip gap size is increased to 2.4 mm at the design operation, the radial profile of the tip gap flow changes drastically. With the large tip gap, the gap flow looks like a two-dimensional channel flow only near the casing. Near the rotor top section, a bigger region with very large shear and reversed flow is observed.

unsteady↗

NASA NTRS2016

Changes in Flat Plate Wake Characteristics Obtained With Decreasing Plate Thickness

The near and very near wake of a flat plate with a circular trailing edge is investigated with data from direct numerical simulations. Computations were performed for four different Reynolds numbers based on plate thickness (D) and at constant plate length. The value of θ/D varies by a factor of approximately 20 in the computations (θ being the boundary layer momentum thickness at the trailing edge). The separating boundary layers are turbulent in all the cases. One objective of the study is to understand the changes in wake characteristics as the plate thickness is reduced (increasing θ/D). Vortex shedding is vigorous in the low θ/D cases with a substantial decrease in shedding intensity in the largest θ/D case (for all practical purposes shedding becomes almost intermittent). Other characteristics that are significantly altered with increasing θ/D are the roll-up of the detached shear layers and the magnitude of fluctuations in shedding period. These effects are explored in depth. The effects of changing θ/D on the distributions of the time-averaged, near-wake velocity statistics are discussed.

Wakes↗

NASA NTRS1993

Sound radiation due to boundary layer transition

This report describes progress made to date towards calculations of noise produced by the laminar-turbulence transition process in a low Mach number boundary layer formed on a rigid wall. The primary objectives of the study are to elucidate the physical mechanisms by which acoustic waves are generated, to clarify the roles of the fluctuating Reynolds stress and the viscous stress in the presence of a solid surface, and to determine the relative efficiency as a noise source of the various transition stages. In particular, we will examine the acoustic characteristics and directivity associated with three-dimensional instability waves, the detached high-shear layer, and turbulent spots following a laminar breakdown. Additionally, attention will be paid to the unsteady surface pressures during the transition, which provide a source of flow noise as well as a forcing function for wall vibration in both aeronautical and marine applications.

Wang, Meng↗

NASA NTRS1991

Hypersonic merged layer blunt body flows with wakes

An attempt is made here to understand the basic physics of the flowfield with wake on a blunt body of revolution under hypersonic rarefied conditions. A merged layer model of flow is envisioned. Full steady-state Navier-Stokes equations in spherical polar coordinate system are computed from the surface with slip and temperature jump conditions to the free stream by the Accelerated Successive Replacement method of numerical integration. Analysis is developed for bodies of arbitrary shape, but actual computations have been carried out for a sphere and sphere-cone body. Particular attention is paid to set the limit of the onset of separation, wake closure, shear-layer impingement, formation and dissipation of the shocks in the flowfield. Validity of the results is established by comparing the present results for sphere with the corresponding results of the SOFIA code in the common region of their validity and with the experimental data.

Jain, Amolak C.↗

NASA NTRS1988

Effect of bulges on the stability of boundary layers

The instability of flows around hump and dip imperfections is investigated. The mean flow is calculated using interacting boundary layers, thereby accounting for viscous/inviscid interaction and separation bubbles. Then, the two-dimensional linear stability of this flow is analyzed, and the amplification factors are computed. Results are obtained for several height/width ratios and locations. The theoretical results have been used to correlate the experimental results of Walker and Greening (1942). The observed transition locations are found to correspond to amplification factors varying between 7.4 and 10.0, consistent with previous results for flat plates. The method accounts for both viscous and shear-layer instabilities. Separation is found to increase significantly the amplification factor.

Nayfeh, Ali H.↗

NASA NTRS1989

Numerical study of a delta planform with multiple jets in ground effect

The flow past a 60-deg delta wing equipped with two thrust-reverser jets near the inboard trailing edge has been analyzed by numerical solution of the 3D thin-layer Navier-Stokes equations. An implicit, partially flux-split, approximately-factored Navier-Stokes solver coupled with a multiple grid embedding scheme has been adapted to this problem. Studies of the impact of numerical parameters (e.g., grid refinement and dissipation levels), and flow-field parameters such as the height of the delta wing above the ground plane and the jet size on the solution, were performed. Results of these numerical studies indicate some challenges in the accurate resolution of complex 3D free shear layers and jets. Nevertheless, flow features such as jet deformation and ground vortex formation observed in experimental flow visualizations are captured. Further, comparisons with experimental data confirm the ability to simulate the loss of wing-borne lift, commonly referred to 'suckdown, as the delta planform flies at slow speeds in close proximity to the ground. Detailed analysis of the numerical results has also given additional insight into the structure of the ground vortex and the mechanisms of lift loss.

Chawla, K.↗

NASA NTRS2013

Hybrid Large-Eddy/Reynolds-Averaged Simulation of a Supersonic Cavity Using VULCAN

Simulations of a supersonic recessed-cavity flow are performed using a hybrid large-eddy/Reynolds-averaged simulation approach utilizing an inflow turbulence recycling procedure and hybridized inviscid flux scheme. Calorically perfect air enters a three-dimensional domain at a free stream Mach number of 2.92. Simulations are performed to assess grid sensitivity of the solution, efficacy of the turbulence recycling, and the effect of the shock sensor used with the hybridized inviscid flux scheme. Analysis of the turbulent boundary layer upstream of the rearward-facing step for each case indicates excellent agreement with theoretical predictions. Mean velocity and pressure results are compared to Reynolds-averaged simulations and experimental data for each case and indicate good agreement on the finest grid. Simulations are repeated on a coarsened grid, and results indicate strong grid density sensitivity. Simulations are performed with and without inflow turbulence recycling on the coarse grid to isolate the effect of the recycling procedure, which is demonstrably critical to capturing the relevant shear layer dynamics. Shock sensor formulations of Ducros and Larsson are found to predict mean flow statistics equally well.

Quinlan, Jesse↗

DOE OSTI2024

The role of RF-induced E×B flows in the mitigation of scrape-off-layer convective transport during ion cyclotron resonance heating

Abstract While multiple experiments have reported a decrease in intermittent fluctuations in the far Scrape-Off-Layer (SOL) during ion cyclotron resonance heating (Antar et al 2010 Phys. Rev. Lett. 105 165001, Li et al 2022 Nucl. Eng. Technol. 54 207–19, Antar et al 2012 Nucl. Fusion 52 103005), the physical mechanism behind this observation has not been fully established yet. In this work, we demonstrate, for the first time, a direct correlation between the amplitude of RF-induced E×B flows and turbulence suppression in the far SOL. Using the Gas Puff Imaging (GPI) diagnostic on Alcator C-Mod, we show again that Ion Cyclotron Range of Frequencies can significantly alter the flow in the SOL and introduce a shear layer in regions magnetically connected close to the antenna (Cziegler et al 2012 Plasma Phys. Control. Fusion 54 105019). With the 4-strap field-aligned antenna operated in dipole phasing, the ratio of the power coupled by the central two straps to the power coupled by the outer two straps was varied. The resulting RF-induced radial electric field magnitude thus varied, and we show that the impact on the far SOL turbulence correlates with the modified E×B velocity. We then apply a newly-developed blob tracking algorithm (Han et al 2022 Sci. Rep. 12 18142) to higher-resolution GPI videos in order to directly observe the process of blob shearing by RF-induced E×B flows. We show that the radially sheared poloidal flows act as a transport barrier by stretching, stopping, and destroying filaments, which is consistent with the observed difference in turbulence statistics.

Diab, R. (ORCID:0000000342065868)↗

NASA NTRS2020

Streak Instabilities on HIFiRE-5 Elliptic Cone

The Hypersonic International Flight Research and Experimentation (HIFiRE) 5 flight experiment by the Air Force Research Laboratories and Australian Defense Science and Technology Organization yielded inflight, hypersonic transition data for a canonical, 3D configuration in the form of an elliptic cone at various combinations of angle-of-attack and yaw. Previous analysis has shown that boundary-layer stability calculations for the as-flown, zero-yaw flight conditions are able to capture the second mode dominated transition along the attachment line as well as the crossflow induced transition in between the attachment line and the minor axis symmetry plane. However, there is still a need to understand the transition in the vicinity of the minor axis plane of symmetry, where the boundary layer thickness exhibits an azimuthally compact bulge due to the collision of the secondary flow approaching from the attachment lines on both sides. This paper reports a computational analysis of the stability of the boundary layer flow along the bulge regions on both the leeward and windward sides of the vehicle surface. At a representative flight condition corresponding to a time instant of t = 514.813 seconds, computations are performed to identify several different unstable modes within the bulge regions, with the eventual goal of developing a linear stability correlation for the transition onset near the minor axis symmetry plane. The most amplified flow instabilities in the pretransitional region correspond to a “stem” mode that is concentrated within a pair of nearly vertical shear layers below the cap of the mushroom shaped bulge in the mean velocity contours. An excellent agreement is found between the predictions of instability amplification based on the plane marching parabolized stability equations (PSE) and the direct numerical solutions (DNS). Given the large number of unstable modes within the bulge region, the observed agreement demonstrates, for first time, that the PSE can provide accurate predictions for the development of flow instabilities in streak-like flow features over three-dimensional bodies. The peak N-factor of approximately 15 at the transition location estimated from the thermocouple measurements along the leeward centerline is close to the transition N-factor for Mack mode transition during the HIFiRE-1 circular cone flight experiment with nearly zero degrees angle of attack.

Meelan Choudhari↗

NASA NTRS2005

Navier-Stokes Computations of a Wing-Flap Model With Blowing Normal to the Flap Surface

A computational study of a generic wing with a half span flap shows the mean flow effects of several blown flap configurations. The effort compares and contrasts the thin-layer, Reynolds averaged, Navier-Stokes solutions of a baseline wing-flap configuration with configurations that have blowing normal to the flap surface through small slits near the flap side edge. Vorticity contours reveal a dual vortex structure at the flap side edge for all cases. The dual vortex merges into a single vortex at approximately the mid-flap chord location. Upper surface blowing reduces the strength of the merged vortex and moves the vortex away from the upper edge. Lower surface blowing thickens the lower shear layer and weakens the merged vortex, but not as much as upper surface blowing. Side surface blowing forces the lower surface vortex farther outboard of the flap edge by effectively increasing the aerodynamic span of the flap. It is seen that there is no global aerodynamic penalty or benefit from the particular blowing configurations examined.

Boyd, D. Douglas, Jr.↗

DOE OSTI2024

Langmuir turbulence in suspended kelp farms

This study investigates the influence of suspended kelp farms on ocean mixed layer hydrodynamics in the presence of currents and waves. We use the large eddy simulation method, where the wave effect is incorporated by solving the wave-averaged equations. Distinct Langmuir circulation patterns are generated within various suspended farm configurations, including horizontally uniform kelp blocks and spaced kelp rows. Intensified turbulence arises from the farm-generated Langmuir circulation, as opposed to the standard Langmuir turbulence observed without a farm. The creation of Langmuir circulation within the farm is attributed to two primary factors depending on farm configuration: (i) enhanced vertical shear due to kelp frond area density variability, and (ii) enhanced lateral shear due to canopy discontinuity at lateral edges of spaced rows. Both enhanced vertical and lateral shear of streamwise velocity, representing the lateral and vertical vorticity components, respectively, can be tilted into downstream vorticity to create Langmuir circulation. This vorticity tilting is driven by the Craik–Leibovich vortex force associated with the Stokes drift of surface gravity waves. In addition to the farm-generated Langmuir turbulence, canopy shear layer turbulence is created at the farm bottom edge due to drag discontinuity. The intensity of different types of turbulence depends on both kelp frond area density and the geometric configuration of the farm. The farm-generated turbulence has substantial consequences for nutrient supply and kelp growth. These findings also underscore the significance of the presence of obstacle structures in modifying ocean mixed layer characteristics.

Bo, Tong (ORCID:0000000260300561)↗

NASA NTRS1993

Investigation of high-speed free shear flows using improved pressure-strain correlated Reynolds stress turbulence model

A high-speed shear layer is studied using compressibility corrected Reynolds stress turbulence model which employs newly developed model for pressure-strain correlation. MacCormack explicit prediction-corrector method is used for solving the governing equations and the turbulence transport equations. The stiffness arising due to source terms in the turbulence equations is handled by a semi-implicit numerical technique. Results obtained using the new model show a sharper reduction in growth rate with increasing convective Mach number. Some improvements were also noted in the prediction of the normalized streamwise stress and Reynolds shear stress. The computed results are in good agreement with the experimental data.

Tiwari, S. N.↗

DOE OSTI2020

How eigenmode self-interaction affects zonal flows and convergence of tokamak core turbulence with toroidal system size

Self-interaction is the process by which a microinstability eigenmode that is extended along the direction parallel to the magnetic field interacts non-linearly with itself. This effect is particularly significant in gyrokinetic simulations accounting for kinetic passing electron dynamics and is known to generate stationary $E\times B$ zonal flow shear layers at radial locations near low-order mode rational surfaces (Weikl et al. Phys. Plasmas, vol. 25, 2018, 072305). Here, we find that self-interaction, in fact, plays a very significant role in also generating fluctuating zonal flows, which is critical to regulating turbulent transport throughout the radial extent. Unlike the usual picture of zonal flow drive in which microinstability eigenmodes coherently amplify the flow via modulational instabilities, the self-interaction drive of zonal flows from these eigenmodes are uncorrelated with each other. It is shown that the associated shearing rate of the fluctuating zonal flows therefore reduces as more toroidal modes are resolved in the simulation. In simulations accounting for the full toroidal domain, such an increase in the density of toroidal modes corresponds to an increase in the toroidal system size, leading to a finite system size effect that is distinct from the well-known profile shearing effect.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NASA NTRS2003

Martian Dust Devils: Laboratory Simulations of Particle Threshold

An apparatus has been fabricated to simulate terrestrial and Martian dust devils. Comparisons of surface pressure profiles through the vortex core generated in the apparatus with both those in natural dust devils on Earth and those inferred for Mars are similar and are consistent with theoretical Rankine vortex models. Experiments to determine particle threshold under Earth ambient atmospheric pressures show that sand (particles > 60 micron in diameter) threshold is analogous to normal boundary-layer shear, in which the rotating winds of the vortex generate surface shear and hence lift. Lower-pressure experiments down to approx. 65 mbar follow this trend for sand-sized particles. However, smaller particles (i.e., dust) and all particles at very low pressures (w 10-60 mbar) appear to be subjected to an additional lift function interpreted to result from the strong decrease in atmospheric pressure centered beneath the vortex core. Initial results suggest that the wind speeds required for the entrainment of grains approx. 2 microns in diameter (i.e., Martian dust sizes) are about half those required for entrainment by boundary layer winds on both Earth and Mars.

Greeley, Ronald↗

NASA NTRS2020

Mechanisms of Stationary Crossflow Instability Growth and Breakdown Induced by Forward-Facing Steps

An experimental study is performed to determine the mechanisms by which a forward-facing step impacts the growth and breakdown to turbulence of the stationary cross-flow instability. Particle image velocimetry measurements are obtained in the boundary layer of a 30◦swept flat plate with a pressure body. Step heights range from 53 % to 71 % of the boundary-layer thickness. The critical step height is approximately 60 % of the boundary-layer thickness for the current study, although it is also shown that the critical step height depends on the initial amplitude of the stationary cross-flow vortices. For the critical cases, the stationary cross-flow amplitude grows sharply downstream of the step, decays for a short region and then grows again. The initial growth region is linear, and can be explained primarily through the impact of the step on the mean flow. Namely, the step causes abrupt changes to the mean flow, resulting in large values of wall-normal shear, as well as highly inflectional profiles, due to either cross-flow reversal, separation or both. These inflectional profiles are highly unstable for the stationary cross-flow. Additionally,the reversed flow regions are significantly modulated by the stationary cross-flow vortices. The second region of growth occurs due to the stationary-cross-flow-induced modulation of the shear layer, which leads to multiple smaller wavelength stream wise vortices. High-frequency fluctuations indicate that the unsteady transition mechanism for the critical cases relates to the shedding of vortices downstream of reattachment of the modulated separated regions.

boundary layer stability↗

NASA NTRS1995

Analysis of in-flight boundary-layer state measurements on a subsonic transport wing in high-lift configuration

Flight experiments on NASA Langley's B737-100 (TSRV) airplane have been conducted to document flow characteristics in order to further the understanding of high-lift flow physics, and to correlate and validate computational predictions and wind-tunnel measurements. The project is a cooperative effort involving NASA, industry, and universities. In addition to focusing on in-flight measurements, the project includes extensive application of various computational techniques, and correlation of flight data with computational results and wind-tunnel measurements. Results obtained in the most recent phase of flight experiments are analyzed and presented in this paper. In-flight measurements include surface pressure distributions, measured using flush pressure taps and pressure belts on the slats, main element, and flap elements; surface shear stresses, measured using Preston tubes; off-surface velocity distributions, measured using shear-layer rakes; aeroelastic deformations of the flap elements, measured using an optical positioning system; and boundary-layer transition phenomena, measured using hot-film anemometers and an infrared imaging system. The analysis in this paper primarily focuses on changes in the boundary-layer state that occurred on the slats, main element, and fore flap as a result of changes in flap setting and/or flight condition. Following a detailed description of the experiment, the boundary-layer state phenomenon will be discussed based on data measured during these recent flight experiments.

vanDam, C. P.↗

NASA NTRS1979

Secondary instability in boundary-layer flows

The stability of a secondary Tollmien-Schlichting wave, whose wavenumber and frequency are nearly one half those of a fundamental Tollmien-Schlichting instability wave is analyzed using the method of multiple scales. Under these conditions, the fundamental wave acts as a parametric exciter for the secondary wave. The results show that the amplitude of the fundamental wave must exceed a critical value to trigger this parametric instability. This value is proportional to a detuning parameter which is the real part of k - 2K, where k and K are the wavenumbers of the fundamental and its subharmonic, respectively. For Blasius flow, the critical amplitude is approximately 29% of the mean flow, and hence many other secondary instabilities take place before this parametric instability becomes significant. For other flows where the detuning parameter is small, such as free-shear layer flows, the critical amplitude can be small, thus the parametric instability might play a greater role.

Nayfeh, A. H.↗