Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STEELS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

Optimization of CCT Equations Using Calculated Grain Boundary Soluble Compositions for the Simulation of Austenite Decomposition of Steels

New CCT equations have been developed and optimized to simulate the start temperatures of the austenite decomposition process in low-alloyed steels using experimental CCT data published in the literature. Exceptionally, this optimization does not apply the nominal compositions of the steels, but the corresponding soluble compositions of the grain boundaries calculated using IDS software, depending on the reported austenitization treatments of the steels. These compositions, rather than the nominal ones, are expected to control the start of the austenite decomposition, which usually initiates at the grain boundaries. The new optimization treatment takes into account the solute microsegregation and the possible precipitate formation. Using IDS software, the new equations were validated with new experimental CCT data. Agreement was good not only for the austenite decomposition start temperatures, but also for the final phase fractions, indicating fairly reasonable predictions of phase transformation kinetics by the IDS. In addition, IDS simulations were compared with the experimental CCT data of five high-carbon steels, applying both the new equations based on grain boundary soluble compositions as well as the equations based on the nominal compositions. With the same experimental CCT data used in optimization, better agreement was obtained with the new equations, indicating the importance of determining the soluble compositions at the grain boundaries where the austenite decomposition process is likely to begin.

36 MATERIALS SCIENCE↗

Computational Design of a Novel Medium-Carbon, Low-Alloy Steel Microalloyed with Niobium

The design of a new steel with specific properties is always challenging owing to the complex interactions of many variables. In this work, this challenge is dealt with by combining metallurgical principles with computational thermodynamics and kinetics to design a novel steel composition suitable for thermomechanical processing and induction heat treatment to achieve a hardness level in excess of 600 HV with the potential for good fracture toughness. CALPHAD-based packages for the thermodynamics and kinetics of phase transformations and diffusion, namely Thermo-Calc{sup ®} and JMatPro{sup ®}, have been combined with an interdendritic segregation tool (IDS) to optimize the contents of chromium, molybdenum and niobium in a proposed medium-carbon low-manganese steel composition. Important factors taken into account in the modeling and optimization were hardenability and as-quenched hardness, grain refinement and alloying cost. For further investigations and verification, the designed composition, i.e., in wt.% 0.40C, 0.20Si, 0.25Mn, 0.90Cr, 0.50Mo, was cast with two nominal levels of Nb: 0 and 0.012 wt.%. The results showed that an addition of Nb decreases the austenite grain size during casting and after slab reheating prior to hot rolling. Validation experiments showed that the predicted properties, i.e., hardness, hardenability and level of segregation, for the designed composition were realistic. It is also demonstrated that the applied procedure could be useful in reducing the number of experiments required for developing compositions for other new steels.

36 MATERIALS SCIENCE↗

Formability, Microstructure and Mechanical Properties of Flow-Formed 17-4 PH Stainless Steel

The subject of the research that has been conducted in this paper was to analyze precipitation-hardened martensitic stainless steel 17-4 PH after flow forming with four different strains and subsequent standard heat treatment. Four cylinders were obtained with a 16, 30, 48 and 68% reduction in thickness, respectively. The samples were analyzed in terms of their mechanical properties and microstructural changes before and after the heat treatment. The results showed that a higher strain resulted in an overall higher strength (up to 1200 MPa UTS) and refinement of the structure, although at a cost of the elongation. High deformation influenced the precipitation process, and the ratio of the grain boundaries significantly increased. Nonetheless, comparing the obtained results with other similar research, it seems that the formation of nano-precipitates of Cu is the key-strengthening mechanism. Strain hardening contributes to an increase in the strength of the steel, although the effect decreases after heat treatment. The relatively small values of residual stress in the steel, especially after the heat treatment, confirmed these claims. Overall, flow forming allowed high deformations of the 17-4 PH steel to be obtained although it did not significantly change the mechanical properties of the material due to the dominant precipitation hardening mechanism.

36 MATERIALS SCIENCE↗

Effect of Y/Zr Ratio on Inclusions and Mechanical Properties of 9Cr-RAFM Steel Fabricated by Vacuum Melting

This study investigates the inclusions, microstructures, tensile properties, and impact toughness of reduced-activation ferritic/martensitic (RAFM) steels with different Y/Zr ratio contents. An optical microscope and a scanning electron microscope (SEM) were employed to determine the size and number of inclusions, and SEM and transmission electron microscope were employed to examine the inclusion types. The increase in Y/Zr ratio influenced the prior austenite grain size owing to the pinning effect of the inclusions. The result of this examination showed that the mechanical properties of the steel are closely related to the refinement of prior austenite grain size and as well as the fine submicron-sized inclusions. The average prior austenite grain sizes of the alloys were 14.5, 13.5, and 13.4 μm for the steels with different Y/Zr ratio contents (i.e., 1/2, 5/3, and 11/2, respectively). Moreover, the submicron-sized inclusions in the alloys achieved densities of 4.71 × 10{sup 16}, 4.49 × 10{sup 16}, and 3.84 × 10{sup 16}/m{sup 3}. The ductile-to-brittle transition temperature (DBTT) decreases when the Y/Zr ratio increases to 5/3. However, the DBTT increases when the Y/Zr ratio reaches 11/2 owing to inclusion coarsening. The RAFM steel with Y content of approximately 0.005 wt.% and Zr content of 0.002 wt.% was verified to exhibit an optimized combination of microstructures, tensile properties, and impact toughness.

36 MATERIALS SCIENCE↗

Unprecedented Capacitance-Based Nondestructive Evaluation of Steels

This work reports for the first time capacitance-based nondestructive evaluation (NDE) of a monolithic metal, namely steel. This means that the structural material is self-sensing, without the need for embedded or attached sensors. The capacitance (2 kHz) can be through-thickness (involving sandwiching electrodes) or in-plane (involving coplanar electrodes), with the latter being superior for NDE, partly due to the relative permittivity being higher in-plane (2 × 10{sup 6}) than through-thickness (28), and partly due to the more effective spreading of the in-plane electric field lines between the coplanar electrodes than the spreading of the through-thickness field lines between the sandwiching electrodes. The fringing field serves as the probe for the flaws at various distances from the electrodes, which are much smaller in area than the specimen. Due to the electrical conductivity of the specimen and the fact that an LCR meter is not designed for measuring the capacitance of a conductive material, each electrode is separated from the specimen by a dielectric film. The conductivity of the specimen accentuates the fringing field. The flaws cause the apparent capacitance to increase, due to the increase in the effective area reached by the fringing field. The capacitance increases monotonically with increasing damage, except that it decreases when the damage in the form of through holes is severe enough to cause the permittivity to decrease. The defect sensing effectiveness is superior for low carbon steel than stainless steel, due to the higher electrical conductivity of low carbon steel and the consequent greater fringing field (current spreading).

36 MATERIALS SCIENCE↗

The Influence of Nickel Additions to Liquid A359 on Hot-Dip Aluminizing of Solid S45C Steel

The properties of hot-dipping A359 aluminum alloys can be improved by strategically placing the S45C steel inserts to locally improve properties such as oxidation and corrosion resistance, but soft A359 aluminum alloy can be easily worn out and thus decreased the S45C steel’s reliability. In this study, we have been added 20 wt.%Ni to increases the hardness of the A359 aluminum alloy, then hot dipped the S45C steel into the molten A359-20 wt.%Ni aluminum alloy for 1 min and then heat treated at 400-600 °C. The effect of nickel on the interface characteristic (including kinetic and shear strengths of interface between the S45C steel and aluminum alloy) and the surface glossiness and wear property of the A359-Ni aluminum alloy is also discussed. The experimental results show that the Fe{sub 2}Al{sub 5} intermetallic compound thus the activation energy of the compound formation in the A359-20 wt.%Ni aluminum alloy, and its thickness increased with an increase in heating temperature. Nickel hindered formation of the Fe{sub 2}Al{sub 5} intermetallic compound thus the activation energy of the compound formation in the A359-20 wt.%Ni aluminum alloy (0.413 eV) is larger than A359 aluminum alloy. The nickel could increase the surface glossiness and anti-wear of the hot-dipped coating layer, but they would not deteriorate the interface shear strength.

36 MATERIALS SCIENCE↗

Material properties and mechanical behaviour of functionally graded steel produced by wire-arc additive manufacturing

Metal Big Area Additive Manufacturing is an additive manufacturing technique based on Gas Metal Arc Welding (GMAW) with the option to use many shielding gases, and materials. The system is equipped with a dual torch design allowing for printing different materials; in our study, AISI 410 stainless steel and AWS ER70S-6 mild steel are both printed in the same component. Different print strategies were designed to highlight changes in material and mechanical properties. Deformation behaviour of a materials’ interface was analysed by two-dimensional digital image correlation of uniaxial tensile specimens in displacement-controlled tests. Instances of non-homogeneous local strains adjacent to the interface are observed, as well as variability in mechanical behaviour and microstructure based on location within the print. Optical and electron microscopy are used to evaluate three microstructural zones in a 5 mm range of the interface between mild steel and stainless steel. Areas far from the interface produced polygonal ferrite and pearlite, while areas close to the interface produced acicular ferrite and bainite. Chromium redistribution profiles are dependent on the print strategy used, as shown by scanning electron microscopy with Energy dispersive spectroscopy. Evidence produced via electron backscatter diffraction is shown to support the argument that transformation induced plasticity is not the cause for the non-homogeneous deformation.

36 MATERIALS SCIENCE↗

Predicting Failure Modes and Ductility of Dual Phase Steels Using Plastic Strain Localization

Ductile failure of metals is often treated as the result of void nucleation, growth and coalescence. Various criteria have been proposed to capture this failure mechanism for various materials. In this study, ductile failure of dual phase steels is predicted in the form of plastic strain localization resulting from the incompatible deformation between the harder marternsite phase and the softer ferrite matrix. Microstructure-level inhomogeneity serves as the initial imperfection triggering the instability in the form of plastic strain localization during the deformation process. Failure modes and ultimate ductility of two dual phase steels are analyzed using finite element analyses based on the actual steel microstructures. The plastic work hardening properties for the constituent phases are determined by the in-situ synchrotron-based high-energy X-ray diffraction technique. Under different loading conditions, different failure modes and ultimate ductility are predicted in the form of plastic strain localization. It is found that the local failure mode and ultimate ductility of dual phase steels are closely related to the stress state in the material. Under plane stress condition with free lateral boundary, one dominant shear band develops and leads to final failure of the material. However, if the lateral boundary is constrained, splitting failure perpendicular to the loading direction is predicted with much reduced ductility. On the other hand, under plane strain loading condition, commonly observed necking phenomenon is predicted which leads to the final failure of the material. These predictions are in reasonably good agreement with experimental observations.

36 MATERIALS SCIENCE↗

Correlation between microstructure and residual stress formation in friction stir welded armor steels characterized by neutron diffraction

Friction stir welding (FSW) is a solid-state joining process that minimizes the heat-affected zone (HAZ) compared with fusion-based arc welding, making it well suited for joining martensitic armor steels where hardness and ballistic resistance are critical. This study investigates residual stress formation in three defect-free FSW butt-joint configurations relevant to armored-vehicle fabrication: similar rolled homogeneous armor (RHA–RHA, Case 1), similar high-hardness armor (HHA–HHA, Case 2), and dissimilar HHA–RHA (Case 3) joints produced under temperature-controlled conditions (770 °C). Neutron diffraction was employed to quantify the magnitude and spatial distribution of residual stresses in the longitudinal, transverse, and normal directions and to correlate them with weld microstructure and hardness. Tensile residual stresses were concentrated in the softened HAZ, reaching approximately 300 MPa for Case 2 and 400 MPa for Case 1 (≈50–70 % of the base-metal yield strength; ∼581 MPa for RHA and ∼566 MPa for HHA), while compressive residual stresses dominated the stir zone. The spatial extent of tensile stresses scaled with the width of the softened HAZ, which was largest in the dissimilar HHA–RHA joint and smallest in the HHA–HHA joint. Full-width-at-half-maximum (FWHM) analysis revealed low microstrain in overtempered HAZ regions and high microstrain in the stir zone associated with severe plastic deformation and fresh martensite formation. This work demonstrates that residual stress evolution in FSW of martensitic armor steels is governed not primarily by peak temperature or thermal contraction, as inferred from fusion-welding analogies, but by the competition between transformation-induced volumetric expansion and tempering-induced stress relaxation. The relative dominance of these mechanisms is shown to depend on alloy hardenability and local thermal history, leading to more extensive HAZ softening and broader tensile stress regions in the lower-hardenability RHA steel. These findings establish a transferable mechanistic framework for optimizing solid-state joining strategies in high-strength steels and other transformation-hardening alloys beyond armor applications.

Friction stir welding↗

Spreading of lithium on a stainless steel surface at room temperature

Lithium conditioned plasma facing surfaces have lowered recycling and enhanced plasma performance on many fusion devices and liquid lithium plasma facing components are under consideration for future machines. A key factor in the performance of liquid lithium components is the wetting by lithium of its container. We have observed the surface spreading of lithium from a mm-scale particle to adjacent stainless steel surfaces using a scanning Auger microprobe that has elemental discrimination. Here, the spreading of lithium occurred at room temperature (when lithium is a solid) from one location at a speed of 0.62 μm/day under ultrahigh vacuum conditions. Separate experiments using temperature programmed desorption (TPD) investigated bonding energetics between monolayer-scale films of lithium and stainless steel. While multilayer lithium desorption from stainless steel begins to occur just above 500 K (E des = 1.54 eV), sub-monolayer Li desorption occurred in a TPD peak at 942 K (E des = 2.52 eV) indicating more energetically favorable lithium-stainless steel bonding (in the absence of an oxidation layer) than lithium lithium bonding.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Influence of annealing conditions on microstructure and phase occurrence in high-alloy CrMnN steels

The influence of annealing at 750, 800, 850, 900 and 950 deg. C for 4 h on the microstructure and the phase occurrence in two high-alloy CrMnN austenitic stainless steels was investigated using light microscopy, transmission electron microscopy, and thermodynamic calculations. Austenite, {sigma}, and Cr{sub 2}N were identified in both steels experimentally. The experimental results were found to be in good agreement with the thermodynamic predictions. In one of the steels, M{sub 23}C{sub 6} as a non-equilibrium probably residual phase was found. Cr{sub 2}N appeared in the steels either in the form of discrete particles or as a part of cells consisting of alternate lamellae of Cr{sub 2}N and austenite.

36 MATERIALS SCIENCE↗

The negative effect of Zr addition on the high temperature strength in alumina-forming austenitic stainless steels

The effect of a Zr addition on the precipitation behavior and mechanical properties in Nb-containing alumina-forming austenitic (AFA) stainless steels was investigated using tensile tests, scanning electron microscopy (SEM), and scanning transmission electron microscopy (STEM) analysis. The TEM observation showed that a Zr addition led to the formation of a (Nb,Zr)(C,N) complex particle, which coarsened the Nb-rich carbonitride. Tensile tests were performed at an elevated temperature (700 °C), and both the tensile and yield strengths decreased with a Zr addition. This unexpected result of a Zr addition was due to the reduction of the precipitation strengthening by particle coarsening. - Highlights: • The effect of Zr on high temperature strength in AFA steel containing Nb was studied. • Both the tensile and yield strengths of an AFA steel decreased with Zr-addition. • This is due to the reduction of precipitation strengthening by particle coarsening. • Nb(C,N) and (Nb,Zr)(C,N) particles were precipitated in an AFA and Zr-added AFA steel. • The size of (Nb,Zr)(C,N) particle is much bigger than that of Nb(C,N) particle.

36 MATERIALS SCIENCE↗

Microstructural characterization of weld joints of 9Cr reduced activation ferritic martensitic steel fabricated by different joining methods

This paper presents a detailed electron microscopy study on the microstructure of various regions of weldment fabricated by three welding methods namely tungsten inert gas welding, electron beam welding and laser beam welding in an indigenously developed 9Cr reduced activation ferritic/martensitic steel. Electron back scatter diffraction studies showed a random micro-texture in all the three welds. Microstructural changes during thermal exposures were studied and corroborated with hardness and optimized conditions for the post weld heat treatment have been identified for this steel. Hollomon–Jaffe parameter has been used to estimate the extent of tempering. The activation energy for the tempering process has been evaluated and found to be corresponding to interstitial diffusion of carbon in ferrite matrix. The type and microchemistry of secondary phases in different regions of the weldment have been identified by analytical transmission electron microscopy. - Highlights: • Comparison of microstructural parameters in TIG, electron beam and laser welds of RAFM steel • EBSD studies to illustrate the absence of preferred orientation and identification of prior austenite grain size using phase identification map • Optimization of PWHT conditions for indigenous RAFM steel • Study of kinetics of tempering and estimation of apparent activation energy of the process.

36 MATERIALS SCIENCE↗

Characterization of microstructure and texture across dissimilar super duplex/austenitic stainless steel weldment joint by super duplex filler metal

In the present paper, microstructural changes across an as-welded dissimilar austenitic/duplex stainless steel couple welded by a super duplex stainless steel filler metal using gas tungsten arc welding process is characterized with optical microscopy and electron back-scattered diffraction techniques. Accordingly, variations of microstructure, texture, and grain boundary character distribution of base metals, heat affected zones, and weld metal were investigated. The results showed that the weld metal, which was composed of Widmanstätten austenite side-plates and allotriomorphic grain boundary austenite morphologies, had the weakest texture and was dominated by low angle boundaries. The welding process increased the ferrite content but decreased the texture intensity at the heat affected zone of the super duplex stainless steel base metal. In addition, through partial ferritization, it changed the morphology of elongated grains of the rolled microstructure to twinned partially transformed austenite plateaus scattered between ferrite textured colonies. However, the texture of the austenitic stainless steel heat affected zone was strengthened via encouraging recrystallization and formation of annealing twins. At both interfaces, an increase in the special character coincident site lattice boundaries of the primary phase as well as a strong texture with <100> orientation, mainly of Goss component, was observed. - Graphical abstract: Display Omitted - Highlights: • Weld metal showed local orientation at microscale but random texture at macroscale. • Intensification of <100> orientated grains was observed adjacent to the fusion lines. • The austenite texture was weaker than that of the ferrite in all duplex regions. • Welding caused twinned partially transformed austenites to form at SDSS HAZ. • At both interfaces, the ratio of special CSL boundaries of the primary phase increased.

36 MATERIALS SCIENCE↗

Fabrication and characterization of microstructure of stainless steel matrix composites containing up to 25 vol% NbC

AISI 440 stainless steels reinforced with various volume fractions of niobium carbide (NbC) particles of up to 25 vol% were fabricated in-situ using an argon arc furnace and then heat-treated to produce a martensitic matrix. Optical and scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and electron back-scatter diffraction (EBSD) techniques were used to analyze the microstructure, phases and composition of these composites. Interestingly, it was found that Chinese-script NbC could nucleate on existing primary NbC particles creating NbC clusters with complex microstructures. Additionally, hardness tests were used to evaluate viability in mining and mineral processing applications. The increase in NbC content resulted in an overall increase in the hardness of the composites while causing a marginal decrease in the amount of Cr in solid solution with the matrix, which could be a concern for corrosion resistance. The latter was due to the fact that the NbC lattice could dissolve a minor amount of Cr. Thermodynamic simulations also attributed this to a slight increase in M{sub 7}C{sub 3} precipitation. Nonetheless, these novel composites show great promise for applications in wear and corrosive environments. - Highlights: •Stainless steels reinforced with NbC particles of up to 25 vol% were fabricated. •NbC was formed in-situ in the steels using an arc melter. •Martensitic transformation of the matrix of each sample was achieved. •NbC reinforcements increased the bulk hardness values of the steels. •Dissolved Cr in the matrix of each sample was sufficient for passivity in theory.

36 MATERIALS SCIENCE↗

A lightweight Fe–Mn–Al–C austenitic steel with ultra-high strength and ductility fabricated via laser powder bed fusion

Lightweight Fe–Mn–Al–C steels have become a topic of significant interest for the defense and automotive industries. These alloys can maintain high strength and ductility while also reducing weight in structural applications. Conventionally processed Fe–Mn–Al–C austenitic steels with high Al content (~9 wt%) demonstrate greater than 1.5 GPa strength with 35% elongation. Several recent studies have demonstrated success in fabricating steel parts using laser powder bed fusion (L-PBF) additive manufacturing (AM), which can generate near-net-shape components with complex geometries and is capable of local microstructural control. However, studies on L-PBF processing of Fe–Mn–Al–C alloys have focused on low Al content (<5 wt%) compositional regimes representing alloys that undergo transformation-induced plasticity (TRIP) and twinning-induced plasticity (TWIP). Here, in this study, we present the effects of L-PBF processing on the microstructure and mechanical properties of an Fe–30Mn–9Al–1Si-0.5Mo-0.9C austenitic steel. A process optimization framework is employed to determine an ideal L-PBF processing space that will result in >99% density parts. Implementing this framework resulted in near-fully dense specimens fabricated over a broad range of process parameters. Additionally, two bi-directional scan rotation strategies (90° and 67°) were applied to understand their effects on texture and anisotropy in this material. As-printed specimens displayed considerable work-hardening characteristics with average strengths of up to 1.3 GPa and 36% elongation in the build direction. However, solidification microcracks oriented in the build direction resulted in anisotropy in tensile strength and ductility resulting in average strengths of 1.1 GPa and 20% elongation perpendicular to the build direction. The successful L-PBF fabrication of Fe–30Mn–9Al–1Si-0.5Mo-0.9C presented here is expected to open new avenues for weight reduction in structural applications with a high degree of control over part topology.

36 MATERIALS SCIENCE↗

Tribology and Tribocorrosion of Case-Hardened Steels: A Review

This report reviews the tribological and tribocorrosion performance of steels that are case-hardened via boriding, chromizing, carburizing, nitriding, nitrocarburizing, and carbonitriding. Case-hardening is commonly used to improve the hardness, impact durability, wear resistance, and corrosion resistance of steel alloys and has been successfully applied in various industries, providing a cost-effective, high-throughput solution for applications involving contact and sliding interfaces in complex service environments. This article summarizes the literature results of the wear and friction behavior of common case-hardening methods for steel alloys under various conditions, including corrosive environments. Special attention is given to the influences of case-hardening process parameters and alloy composition on tribological performance. Furthermore, by discussing key findings from the literature, this review provides insights into optimizing case-hardening processes for improving the tribological and tribocorrosion performance of steel alloys.

Alloys↗

Review of passive corrosion studies of carbon steel in concrete in the context of disposal of HLW and spent fuel in Belgium

The Supercontainer (SC) design is the preferred option for the final disposal of high level nuclear waste and spent fuel in Belgium. The SC consists of a carbon steel overpack surrounded by a very thick concrete buffer, contained within a stainless steel envelope. In this highly alkaline environment of the annulus and under normal conditions (without the ingress of aggressive species), the carbon steel overpack will be protected by a passive oxide film, which is believed to result in very low and almost negligible uniform corrosion rates. This paper discusses the modeling efforts simulating the evolution of various parameters that can potentially influence the corrosion processes (temperature, pH, saturation degree and concentration of aggressive species). The outcome of the Belgian experimental program to study the passive uniform corrosion of carbon steel in concrete is also addressed. Long-term uniform corrosion rates are determined using different independent techniques (hydrogen gas measurements by means of manometric gas cells or pressure transducers, long-term passive current density measurements). (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗