Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SILICONES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Friction behavior of silicon in contact with titanium, nickel, silver and copper

Sliding friction experiments are conducted with the semiconductor silicon in contact with the metals titanium, nickel, copper, and silver. Sliding is on the (111) plane of single-crystal silicon in the 112 crystallographic direction both in dry and lubricated (mineral oil) sliding. The friction coefficient in dry sliding is controlled by adhesion and the surface chemical activity of the metal. The more active the metal the stronger the adhesion and the higher the friction. In lubricated sliding the lubricant absorbs to the surfaces and reduces the importance of metal chemical effects. In lubricated sliding, silicon ceases to behave in a brittle manner and undergoes plastic deformation under load.

Mishina, H.↗
NASA NTRS1984

Process Research of Polycrystalline Silicon Material (PROPSM)

A passivation process (hydrogenation) that will improve the power generation of solar cells fabricated from presently produced, large grain, cast polycrystalline silicon (Semix), a potentially low cost material are developed. The first objective is to verify the operation of a DC plasma hydrogenation system and to investigate the effect of hydrogen on the electrical performance of a variety of polycrystalline silicon solar cells. The second objective is to parameterize and optimize a hydrogenation process for cast polycrystalline silicon, and will include a process sensitivity analysis. The sample preparation for the first phase is outlined. The hydrogenation system is described, and some early results that were obtained using the hydrogenation system without a plasma are summarized. Light beam induced current (LBIC) measurements of minicell samples, and their correlation to dark current voltage characteristics, are discussed.

Culik, J. S.↗
NASA NTRS1984

Silicon nitride films deposited with an electron beam created plasma

The electron beam assisted chemical vapor deposition (EBCVD) of silicon nitride films using NH3, N2, and SiH4 as the reactant gases is reported. The films have been deposited on aluminum, SiO2, and polysilicon film substrates as well as on crystalline silicon substrates. The range of experimental conditions under which silicon nitrides have been deposited includes substrate temperatures from 50 to 400 C, electron beam currents of 2-40 mA, electron beam energies of 1-5 keV, total ambient pressures of 0.1-0.4 Torr, and NH3/SiH4 mass flow ratios of 1-80. The physical, electrical, and chemical properties of the EBCVD films are discussed.

Bishop, D. C.↗
NASA NTRS1985

High-Purity Silicon Seeds for Silane Pyrolysis

Seed particles for fluidized-bed production of silicon made by new contamination-free, economical method. In new method, large particles of semiconductor-grade silicon fired at each other by high-speed streams of gas and thereby break up into particles of suitable size for fluidized bed. No foreign materials introduced, and leaching unnecessary. Method used to feed fluidized-bed reactor for continuous production of high-purity silicon.

Hsu, G. C.↗
NASA NTRS1986

Extracting Silicon Product From Fluidized-Bed Reactors

Silicon particles continuously removed from bottom of fluidizedbed reactor when grown to large size. In reactor, silane (SiH4) flows through bed of small silicon seed particles at temperature of 650 degrees to 700 degrees C. Silane decomposes into silicon vapor and hydrogen gas, and vapor deposits as solid on seed particles. With withdrawal system, reactor operates continuously.

Hsu, G. C.↗
NASA NTRS1986

Beta Silicon Nitride Whiskers

Process for growing fibrous beta silicon nitride helps meet potentially great demand for silicon nitride ceramics. Ceramics have high tensile strength and resistance to thermal shock, which make them attractive choice for high-temperature engine parts. Process forms whiskers of strong, stable, heatresistant material. Whiskers expected to find application as reinforcement in composite silicon nitride ceramic parts. Corklike material useful in present form for thermal barrier tiles. Process forms whiskers of strong, stable, heat-resistant material.

Holliday, R. J.↗
NASA NTRS1985

Tensile test of pressureless-sintered silicon nitride at elevated temperature

Uniaxial tensile strength tests of pressureless sintered silicon nitride were carried out in air at temperatures ranging from room temperature up to 1600 C. Silicon nitrides containing Y2O3, Al2O3, Al2O3-MgO, or MgO-CeO2 additives were tested. The results show that the composition of the additive used influences the strength characteristics of the silicon nitride. The tensile strength rapidly decreased at temperatures above 1000 C for the materials containing MgO as the additive and above 1000 C for the material with Y2O3. When the temperature increased to as high as 1300 C, the strength decreased to about 10 percent of the room temperature strength in each case. Observations of the fracture origin and of the crack propagation on the fracture surfaces are discussed.

Matsusue, K.↗
NASA NTRS1984

Silicon film solar cell process

The most promising way to reduce the cost of silicon in solar cells while still maintaining performance is to utilize thin films (10 to 20 microns thick) of crystalline silicon. The method of solution growth is being employed to grow thin polycrystalline films of silicon on dissimilar substrates. The initial results indicate that, using tin as the solvent, this growth process only requires operating temperatures in the range of 800 C to 1000 C. Growth rates in the range of 0.4 to 2.0 microns per minute and grain sizes in the range of 20 to 100 microns were achieved on both quartz and coated steel substrates. Typically, an aspect ratio of two to three between the width and the Si grain thickness is seen. Uniform coverage of Si growth on quartz over a 2.5 x 2.5 cm area was observed.

Hall, R. B.↗
NASA NTRS1985

Process Research on Polycrystalline Silicon Material (PROPSM)

Results of hydrogen-passivated polycrysalline silicon solar cell research are summarized. The short-circuit current of solar cells fabricated from large-grain cast polycrystalline silicon is nearly equivalent to that of single-crystal cells, which indicates long bulk minority-carrier diffusion length. Treatments with molecular hydrogen showed no effect on large-grain cast polycrystalline silicon solar cells.

Culik, J. S.↗
NASA NTRS1985

Microgravity silicon zoning investigation

The flow instabilities in floating zones of silicon were investigated and methods for investigation of these instabilities in microgravity were defined. Three principal tasks were involved: (1) characterization of the float zone in small diameter rods; (2) investigation of melt flow instabilities in circular melts in silicon disks; and (3) the development of a prototype of an apparatus that could be used in near term space experiments to investigate flow instabilities in a molten zone. It is shown that in a resistance heated zoner with 4 to 7 mm diameter silicon rods that the critical Marangoni number is about 1480 compared to a predicted value of 14 indicative that viable space experiments might be performed. The prototype float zone apparatus is built and specifications are prepared for a flight zoner should a decision be reached to proceed with a space flight experimental investigation.

Kern, E. L.↗
NASA NTRS1985

Silicon solar cell efficiency improvement: Status and outlook

Efficiency and operating life is an economic attribute in silicon solar cells application. The efficiency improvements made during the 30 year existence of the silicon solar cells, from about 6% efficiency at the beginning to 19% in the most recent experimental cells is illustrated. In the more stationary periods, the effort was oriented towards improving radiation resistance and yields on the production lines, while, in other periods, the emphasis was on reaching new levels of efficiency through better cell design and improved material processing. First results were forthcoming from the recent efforts. Considerably more efficiency advancement in silicon solar cells is expected, and the anticipated attainment of efficiencies significantly above 20% is discussed. Major advances in material processing and in the resulting material perfection are required.

Wolf, M.↗
NASA NTRS1984

Silicon refinement by chemical vapor transport

Silicon refinement by chemical vapor transport is discussed. The operating characteristics of the purification process, including factors affecting the rate, purification efficiency and photovoltaic quality of the refined silicon were studied. The casting of large alloy plates was accomplished. A larger research scale reactor is characterized, and it is shown that a refined silicon product yields solar cells with near state of the art conversion efficiencies.

Olson, J.↗
NASA NTRS1984

Electronic and chemical structure of metal-silicon interfaces

This paper reviews our current understanding of the near-noble metal silicides and the interfaces formed with Si(100). Using X-ray photoemission spectroscopy, we compare the chemical composition and electronic structure of the room temperature metal-silicon and reacted silicide-silicon interfaces. The relationship between the interfacial chemistry and the Schottky barrier heights for this class of metals on silicon is explored.

Grunthaner, P. J.↗
NASA NTRS1984

Kinetics of thermal donor generation in silicon

The generation kinetics of thermal donors at 450 C in Czochralski-grown silicon was found to be altered by high-temperature preannealing (e.g., 1100 C for 30 min). Thus, when compared with as-grown Si, high-temperature preannealed material exhibits a smaller concentration of generated thermal donors and a faster thermal donor saturation. A unified mechanism of nucleation and oxygen diffusion-controlled growth (based on solid-state plate transformation theory) is proposed to account for generation kinetics of thermal donors at 450 C, in as-grown and high-temperature preannealed Czochralski silicon crystals. This mechanism is consistent with the main features of the models which have been proposed to explain the formation of oxygen thermal donors in silicon.

Mao, B.-Y.↗
NASA NTRS1983

Monolithic lead salt-silicon focal plane development

This paper is a summary of work done in the development of monolithic lead salt-silicon infrared focal plane technology. The photoconductive detector materials, PbS and PbSe are chemically deposited onto premetallized silicon MOSFET integrated circuit wafers. A variety of structures based on an implanted PMOS process were fabricated and evaluated. Operational results of an eight-element PbS array multiplexed on-chip are presented along with radiometric measurements on other integrated PbS-silicon MOSFET structures. PbS imagery is shown using one element of a 20-element array integrated on-chip.

Barrett, J. R.↗
NASA NTRS1985

Boron and silicon - Filters for the extreme ultraviolet

Thin films of boron and silicon have been developed using electron beam deposition. The transmissions of these filters were measured from soft X-ray wavelengths to the far ultraviolet and at optical wavelengths. The boron filter transmission peaks near 66 A and the silicon filter peaks near 136 A as expected on theoretical grounds, but the extreme ultraviolet bandpass is narrower than expected. The peak transmission of these filters does not change with time, but the width of the silicon filter bandpass is reduced slightly as the filter ages.

Labov, S.↗
NASA NTRS1985

The feasibility of silicon on garnet technology

The feasibility of combining silicon and magnetic bubble technologies is demonstrated. Functional MOSFETs have been fabricated on top of bubble films coated with 1-micron thick SiO2 layers. The large grain silicon necessary for these devices is obtained by laser recrystallization of polycrystalline silicon (polysilicon). The laser-recrystallization process causes changes in the magnetic properties of the bubble film; however, these changes can be reversed by subsequent thermal anneals. The required temperature treatments after laser annealing are compatible with the MOSFET fabrication process.

Rasky, P. H. L.↗
NASA NTRS1984

Recombination-active defects in silicon ribbon and polycrystalline solar cells

This paper reports results from a study of recombination-active structural defects in silicon ribbon and polycrystalline solar cells using the electron beam induced current (EBIC) technique in a scanning electron microscope. It is demonstrated that low temperature EBIC measurements can reveal a range of defects that are not observable at room temperature, including slip dislocations in silicon dendritic web ribbons as well as decorated twin boundaries and dislocation complexes in cast polycrystalline silicon solar cell materials.

Cheng, L. J.↗