SEARCH · Engineering Papers

Results for “Real numbers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

All sources NASA NTRS DOE OSTI

NASA NTRS2003

TF41 Engine Fan Disk Seeded Fault Crack Propagation Test

Uncontained engine failures, although rare in occurrence, can have a catastrophic effect on aircraft performance and safety. Engine disk cracks can eventually lead to these type of failures. A number of techniques to detect engine disk cracks have been developed in recent years. However, these technologies have only been validated by disk spin pit tests, not actual engine tests. Due to this, a project was established to perform seeded fault engine tests on a TF41 engine disk fan. A defect was machined in the first stage fan disk of a TF41 engine. The disk was run in a spin pit to initiate a crack. Once initiated, the disk was run in an actual engine test facility. The engine was cycled by a number of start and stops with the goal of propagating the crack to disk burst through low cycle fatigue. Various crack detection techniques were installed on the engine and run real-time during the test to validate their abilities to detect disk cracks. These techniques were based on methods such as change in mass imbalance using vibration or shaft displacement, change in blade position, acoustic emission, and torsional resonance. At the completion of 4474 test cycles, the crack in the TF41 disk was determined to have grown approximately 0.025 inches. This was far less the predicted crack growth based on a fracture mechanics analysis and finite element stress analysis.

Lewicki, David G.↗

NASA NTRSDate not supplied

Comparison of Acoustic Models and Trajectory Generation Methods for an Acoustically-Aware Aircraft

This paper presents a comparison of trajectory generation methodologies using acoustic source noise models of different fidelity for motion planning for an acoustically-aware aircraft subject to constraints on the vehicle dynamic performance, mission, and acoustic footprint of the vehicle at a set of (three-dimensional) observer locations. The performance of a pre-mission Bézier curve-based planner and a (near) real-time stochastic model predictive control planner are compared. Additionally, a comparison is made between the motion planning performance using a lower-fidelity acoustic model based on propeller tip Mach number and omni-directional sound power radiation, and a hemisphere-based higher-fidelity acoustic model. It is demonstrated that the asymmetry in hemisphere-based acoustic model can be exploited for improved flight path planning and trajectory-tracking performance in the presence of acoustic constraints.

Kasey A Ackerman↗

NASA NTRS2015

High-Resolution Mesoscale Model Setup for the Eastern Range and Wallops Flight Facility

Mesoscale weather conditions can have an adverse effect on space launch, landing, ground processing, and weather advisories, watches, and warnings at the Eastern Range (ER) in Florida and Wallops Flight Facility (WFF) in Virginia. During summer, land-sea interactions across Kennedy Space Center (KSC) and Cape Canaveral Air Force Station (CCAFS) lead to sea breeze front formation, which can spawn deep convection that can hinder operations and endanger personnel and resources. Many other weak locally-driven low-level boundaries and their interactions with the sea breeze front and each other can also initiate deep convection in the KSC/CCAFS area. These convective processes often last 60 minutes or less and pose a significant challenge to the local forecasters. Surface winds during the transition seasons (spring and fall) pose the most difficulties for the forecasters at WFF. They also encounter problems forecasting convective activity and temperature during those seasons. Therefore, accurate mesoscale model forecasts are needed to better forecast a variety of unique weather phenomena. Global and national scale models cannot properly resolve important local-scale weather features at each location due to their horizontal resolutions being much too coarse. Therefore, a properly tuned local data assimilation (DA) and forecast model at a high resolution is needed to provide improved capability. To accomplish this, a number of sensitivity tests were performed using the Weather Research and Forecasting (WRF) model in order to determine the best DA/model configuration for operational use at each of the space launch ranges to best predict winds, precipitation, and temperature. A set of Perl scripts to run the Gridpoint Statistical Interpolation (GSI)/WRF in real-time were provided by NASA's Short-term Prediction Research and Transition Center (SPoRT). The GSI can analyze many types of observational data including satellite, radar, and conventional data. The GSI/WRF scripts use a cycled GSI system similar to the operational North American Mesoscale (NAM) model. The scripts run a 12-hour pre-cycle in which data are assimilated from 12 hours prior up to the model initialization time. A number of different model configurations were tested for both the ER and WFF by varying the horizontal resolution on which the data assimilation was done. Three different grid configurations were run for the ER and two configurations were run for WFF for archive cases from 27 Aug 2013 through 10 Nov 2013. To quantify model performance, standard model output will be compared to the Meteorological Assimilation Data Ingest System (MADIS) data. The MADIS observation data will be compared to the WRF forecasts using the Model Evaluation Tools (MET) verification package. In addition, the National Centers for Environmental Prediction's Stage IV precipitation data will be used to validate the WRF precipitation forecasts. The author will summarize the relative skill of the various WRF configurations and how each configuration behaves relative to the others, as well as determine the best model configuration for each space launch range.

Watson, Leela R.↗

NASA NTRS1983

On the feasibility of real-time prediction of aircraft carrier motion at sea

Landing aircraft on board carriers is a most delicate phase of flight operations at sea. The ability to predict the aircraft carrier's motion over an interval of several seconds within reasonable error bounds may allow an improvement in touchdown dispersion and reduce the value of the ramp clearance due to a smoother aircraft trajectory. Also, improved information to the landing signal officer should decrease the number of waveoffs substantially. This paper indicates and shows quantitatively that, based upon the power density spectrum data for pitch and heave measured for various ships and sea conditions, the motion can be predicted well, for up to 15 s. Moreover, the zero crossover times for both pitch and heave motions can be predicted with impressive accuracy. The predictor was designed on the basis of Kalman's optimum filtering theory (the discrete time case), being compatible with real-time digital computer operation.

Sidar, M. M.↗

NASA NTRS2006

Real-Time Feedback Control of Flow-Induced Cavity Tones: Fixed-Gain Control - Part 1

A generalized predictive control (GPC) algorithm was formulated and applied to the cavity flow-tone problem. The control algorithm demonstrated multiple Rossiter-mode suppression at fixed Mach numbers ranging from 0.275 to 0.38. Controller performance was evaluated with a measure of output disturbance rejection and an input sensitivity transfer function. The results suggest that disturbances entering the cavity flow are collocated with the control input at the cavity leading edge. In that case, only tonal components of the cavity wall-pressure fluctuations can be suppressed and arbitrary broadband pressure reduction is not possible with the present sensor/actuator arrangement. In the control-algorithm development, the cavity dynamics were treated as linear and time invariant (LTI) for a fixed Mach number. The experimental results lend support to that treatment.

Kegerise, M. A.↗

NASA NTRS1996

Development of High Speed Imaging and Analysis Techniques Compressible Dynamics Stall

Dynamic stall has limited the flight envelope of helicopters for many years. The problem has been studied in the laboratory as well as in flight, but most research, even in the laboratory, has been restricted to surface measurement techniques such as pressure transducers or skin friction gauges, except at low speed. From this research, it became apparent that flow visualization tests performed at Mach numbers representing actual flight conditions were needed if the complex physics associated with dynamic stall was to be properly understood. However, visualization of the flow field during compressible conditions required carefully aligned and meticulously reconstructed holographic interferometry. As part of a long-range effort focused on exposing of the physics of compressible dynamic stall, a research wind tunnel was developed at NASA Ames Research Center which permits visual access to the full flow field surrounding an oscillating airfoil during compressible dynamic stall. Initially, a stroboscopic schlieren technique was used for visualization of the stall process, but the primary research tool has been point diffraction interferometry(PDI), a technique carefully optimized for use in th is project. A review of the process of development of PDI will be presented in the full paper. One of the most valuable aspects of PDI is the fact that interferograms are produced in real time on a continuous basis. The use of a rapidly-pulsed laser makes this practical; a discussion of this approach will be presented in the full paper. This rapid pulsing(up to 40,000 pulses/sec) produces interferograms of the rapidly developing dynamic stall field in sufficient resolution(both in space and time) that the fluid physics of the compressible dynamic stall flowfield can be quantitatively determined, including the gradients of pressure in space and time. This permits analysis of the influence of the effect of pitch rate, Mach number, Reynolds number, amplitude of oscillation, and other parameters on the dynamic stall process. When interferograms can be captured in real time, the potential for real-time mapping of a developing unsteady flow such as dynamic stall becomes a possibility. This has been achieved in the present case through the use of a high-speed drum camera combined with electronic circuitry which has resulted in a series of interferograms obtained during a single cycle of dynamic stall; images obtained at the rate of 20 KHz will be presented as a part of the formal presentation. Interferometry has been available for a long time; however, most of its use has been limited to visualization. The present research has focused on use of interferograms for quantitative mapping of the flow over oscillating airfoils. Instantaneous pressure distributions can now be obtained semi-automatically, making practical the analysis of the thousands of interferograms that are produced in this research. A review of the techniques that have been developed as part of this research effort will be presented in the final paper.

Chandrasekhara, M. S.↗

NASA NTRS1973

A highly efficient error analysis program for the evaluation of spacecraft tests of general relativity with application to solar probes

A computer program is described which can be used to study the feasibility of conducting relativity experiments on a wide range of hypothetical space missions, and a few applications are presented for solar probes which approach the Sun within 0.25 to 0.35 AU. It is assumed that radio ranging data are available from these spacecraft, and that accuracies on the order of 15 meters can be achieved. This is compatible with current accuracies of ranging to Mariner spacecraft. At this level of accuracy, the range data are sensitive to a number of effects, and for this reason it has been necessary to include a total of up to 23 parameters in the feasibility studies, even though there are only two parameters of real interest in the relativity experiments.

Anderson, J. D.↗

NASA NTRS1974

A boundary-layer analysis of atmospheric motion over a semi-elliptical surface obstruction

Flow over surface obstructions can produce adverse flying conditions for helicopters, V/STOL vehicles, etc. The disturbed boundary-layer concept is applied in approximating the localized flow field induced around a surface obstruction (modeled by a two-dimensional cylinder with elliptical cross section) by an impinging wind. The analysis concludes that: (1) localized wind-speed maxima occur at the top of a surface obstruction, which are expected in physically real flows; (2) increased elliptical aspect ratio decreases with speed within the boundary layer at the top of the ellipse; (3) increased surface roughness decreases velocity in the boundary layer; (4) Reynolds number has a negligible effect on the overall flow for the Re range considered; (5) decreased elliptical aspect ratio and increased surface roughness cause larger separation regions.

Frost, W.↗

NASA NTRS1980

Intensification and refraction of acoustical signals in partially choked converging ducts

A computer code based on the wave-envelope technique is used to perform detailed numerical calculations for the intensification and refraction of sound in converging hard walled and lined circular ducts carrying high mean Mach number flows. The results show that converging ducts produce substantial refractions toward the duct center for waves propagating against near choked flows. As expected, the magnitude of the refraction decreases as the real part of the admittance increases. The pressure wave pattern is that of interference among the different modes, and hence the variation of the magnitude of pressure refraction with frequency is not monotonic.

Nayfeh, A. H.↗

NASA NTRS1986

UT/CSR analysis of earth rotation from Lageos SLR data

The 1983-1984 data collected by NASA and stations participating in the Crustal Dynamics Project from satellite laser ranging (SLR) systems are used to generate solutions for the earth polar motion. Solutions obtained using the MERIT Lageos standard data set are compared to operational results based on quick-look data and generated in near real-time, and the capability of Lageos SLR for the determination of earth orientation parameters (EOP) with high temporal resolution is investigated. Finally, the sensitivity of the MERIT campaign results to the number of tracking stations and to changes in the MERIT standard model is evaluated. It is concluded that the departures from the IAU/IUGG MERIT standards do not significantly change the solution and that solutions accurate at the 2 milliarcsec level can be maintained with a network of fewer than 10 appropriately selected stations.

Tapley, B. D.↗

NASA NTRS1988

Event-related brain potentials as indices of mental workload and attentional allocation

Over the past decade considerable strides were made in explicating the antecedant conditions necessary for the elicitation, and the modulation of the amplitude and latency, of a number of components of the event-related brain potential (ERP). The focus of this report is on P300. The degree to which the psychophysiological measures contribute to issues in two real-world domains (communication devices for the motor impaired and the assessment of mental workload of aircraft pilots) are examined.

Arthur F Krainer↗

NASA NTRS1989

A VLSI chip set for real time vector quantization of image sequences

The architecture and implementation of a VLSI chip set that vector quantizes (VQ) image sequences in real time is described. The chip set forms a programmable Single-Instruction, Multiple-Data (SIMD) machine which can implement various vector quantization encoding structures. Its VQ codebook may contain unlimited number of codevectors, N, having dimension up to K = 64. Under a weighted least squared error criterion, the engine locates at video rates the best code vector in full-searched or large tree searched VQ codebooks. The ability to manipulate tree structured codebooks, coupled with parallelism and pipelining, permits searches in as short as O (log N) cycles. A full codebook search results in O(N) performance, compared to O(KN) for a Single-Instruction, Single-Data (SISD) machine. With this VLSI chip set, an entire video code can be built on a single board that permits realtime experimentation with very large codebooks.

Baker, Richard L.↗

NASA NTRS1989

The NASA Langley Research Center 0.3-meter transonic cryogenic tunnel T-P/Re-M controller manual

A new microcomputer based controller for the 0.3-m Transonic Cryogenic Tunnel (TCT) has been commissioned in 1988 and has reliably operated for more than a year. The tunnel stagnation pressure, gas stagnation temperature, tunnel wall structural temperature and flow Mach number are precisely controlled by the new controller in a stable manner. The tunnel control hardware, software, and the flow chart to assist in calibration of the sensors, actuators, and the controller real time functions are described. The software installation details are also presented. The report serves as the maintenance and trouble shooting manual for the 0.3-m TCT controller.

Balakrishna, S.↗

NASA NTRS1989

Distributed earth model/orbiter simulation

Distributed Earth Model/Orbiter Simulation (DEMOS) is a network based application developed for the UNIX environment that visually monitors or simulates the Earth and any number of orbiting vehicles. Its purpose is to provide Mission Control Center (MCC) flight controllers with a visually accurate three dimensional (3D) model of the Earth, Sun, Moon and orbiters, driven by real time or simulated data. The project incorporates a graphical user interface, 3D modelling employing state-of-the art hardware, and simulation of orbital mechanics in a networked/distributed environment. The user interface is based on the X Window System and the X Ray toolbox. The 3D modelling utilizes the Programmer's Hierarchical Interactive Graphics System (PHIGS) standard and Raster Technologies hardware for rendering/display performance. The simulation of orbiting vehicles uses two methods of vector propagation implemented with standard UNIX/C for portability. Each part is a distinct process that can run on separate nodes of a network, exploiting each node's unique hardware capabilities. The client/server communication architecture of the application can be reused for a variety of distributed applications.

Geisler, Erik↗

NASA NTRS1987

Simulation of real-gas effects on pressure distributions for a proposed Aeroassist Flight Experiment vehicle and comparison to prediction

Pressure distributions measured on a 60-deg elliptic cone, raked off at a 73-deg angle and having an ellipsoid nose (ellipticity equal to 2.0), are presented for a range of angle of attack from -10 to 15 deg. The high normal shock density ratio aspect of a real gas was simulated by testing in Mach-6 air (normal shock density ratio equal to 5.25) and Mach 6 CF4 (normal shock density ratio equal to 12.0). The effects of Reynolds number, angle of attack, and normal shock density ratio on these measurements are examined, and comparisons are made to an inviscid flowfield computer code known as HALIS. A significant effect of density ratio on pressure distributions on the cone section of the configuration was observed; the magnitude of this effect decreased with increased angle of attack. The effect of Reynolds number on pressures was negligible for forebody pressure distributions, but a measurable effect was noted on base pressures. In general, the HALIS code accurately predicted the measured pressure distributions in air and CF4.

Micol, John R.↗

NASA NTRS1991

An expert system for astronaut scientists

A novel application of expert system technology is developed for real-time advice to an astronaut during the performance of a crew intensive experiment. The provision of an on-board computer expert, containing much of the reasoning base of the real Principal Investigator, will permit the astronaut to act more as a scientist co-worker in future Spacelab and Space Station missions. The long duration of flight increments and the large number of experiments envisioned for Space Station Freedom make the increase in astronaut productivity particularly valuable. A first version of the system was evaluated on the ground during the recent Spacelab SLS-1 flight.

Young, L. R.↗

NASA NTRS1992

Extracting galactic structure parameters from multivariated density estimation

Multivariate statistical analysis, including includes cluster analysis (unsupervised classification), discriminant analysis (supervised classification) and principle component analysis (dimensionlity reduction method), and nonparameter density estimation have been successfully used to search for meaningful associations in the 5-dimensional space of observables between observed points and the sets of simulated points generated from a synthetic approach of galaxy modelling. These methodologies can be applied as the new tools to obtain information about hidden structure otherwise unrecognizable, and place important constraints on the space distribution of various stellar populations in the Milky Way. In this paper, we concentrate on illustrating how to use nonparameter density estimation to substitute for the true densities in both of the simulating sample and real sample in the five-dimensional space. In order to fit model predicted densities to reality, we derive a set of equations which include n lines (where n is the total number of observed points) and m (where m: the numbers of predefined groups) unknown parameters. A least-square estimation will allow us to determine the density law of different groups and components in the Galaxy. The output from our software, which can be used in many research fields, will also give out the systematic error between the model and the observation by a Bayes rule.

Chen, B.↗

NASA NTRS2001

Quality of Service for Real-Time Applications Over Next Generation Data Networks

This project, which started on January 1, 2000, was funded by the NASA Glenn Research Center for duration of one year. The deliverables of the project included the following tasks: (1) Study of QoS mapping between the edge and core networks envisioned in the Next Generation networks will provide us with the QoS guarantees that can be obtained from next generation networks; (2) Buffer management techniques to provide strict guarantees to real-time end-to-end applications through preferential treatment to packets belonging to real-time applications. In particular, use of ECN to help reduce the loss on high bandwidth-delay product satellite networks needs to be studied; (3) Effect of Prioritized Packet Discard to increase goodput of the network and reduce the buffering requirements in the ATM switches; (4) Provision of new IP circuit emulation services over Satellite IP backbones using MPLS will be studied; and (5) Determine the architecture and requirements for internetworking ATN and the Next Generation Internet for real-time applications. The project has been completed on time. All the objectives and deliverables of the project have been completed. Research results obtained from this project have been published in a number of papers in journals, conferences, and technical reports, included in this document.

Atiquzzaman, Mohammed↗