Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Polymer morphology”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Anion-tethered Single Lithium-ion Conducting Polyelectrolytes through UV-induced Free Radical Polymerization for Improved Morphological Stability of Lithium Metal Anodes

Single Li + ion conducting polyelectrolytes (SICs), which feature covalently tethered counter-anions along their backbone, have the potential to mitigate dendrite formation by reducing concentration polarization and preventing salt depletion. However, due to their low ionic conductivity and complicated synthetic procedure, the successful validation of these claimed advantages in lithium metal (Li 0 ) anode batteries remains limited. In this study, we fabricated a SIC electrolyte using a single-step UV polymerization approach. The resulting electrolyte exhibited a high Li + transference number (t + ) of 0.85 and demonstrated good Li + conductivity (6.3×10 -5 S/cm at room temperature), which is comparable to that of a benchmark dual ion conductor (DIC, 9.1×10 -5 S/cm). Benefitting from the high transference number of SIC, it displayed a three-fold higher critical current density (2.4 mA/cm 2 ) compared to DIC (0.8 mA/cm 2 ) by successfully suppressing concentration polarization-induced short-circuiting. Additionally, the t + significantly influenced the deposition behavior of Li 0 , with SIC yielding a uniform, compact, and mosaic-like morphology, while the low t + DIC resulted in a porous morphology with Li 0 whiskers. In conclusion, using the SIC electrolyte, Li 0 ||LiFePO 4 cells exhibited stable operation for 4500 cycles with 70.5 % capacity retention at 22 °C.

25 ENERGY STORAGE↗
NASA NTRS1991

Atomic oxygen erosion of polymer matrix composites

Results are presented on atomic oxygen erosion of circular tubes and flat plates fabricated from different epoxy matrix composites containing, boron and Kevlar fiber reinforcements. The UTIAS experiment was located at station D-12, at 90 deg to the LDEF leading edge which was yawed about approximately 8 to 10 deg relative to the velocity vector. This resulted in enhanced atomic oxygen exposure at D-12, providing a total fluence of about 4 x 10(exp 20) atoms/sq cm. Thickness loss measurements were obtained for both flat plates and cylindrical tubes. The effect of reflected atomic oxygen on erosion yield and surface morphology on back surfaces (not directly exposed to AO) are graphically demonstrated. Erosion yields are also compared with other space flight data for similar materials, and ground-based tests in the UTIAS AO simulator. The effect of angle of incidence on surface morphology, erosion profiles and thickness losses are presented and the results correlated with simulator tests as well.

Tennyson, R. C.↗
NASA NTRS2024

Contamination Results of MISSE 8 Wake and Nadir Samples After 2 Years of Space Exposure on the International Space Station

Spacecraft in low Earth orbit (LEO) are subjected to harsh environmental conditions, including radiation (cosmic rays, ultraviolet, x-ray and charged particle radiation), micrometeoroids and orbital debris, temperature extremes, thermal cycling, and atomic oxygen. In addition, on-orbit spacecraft contamination is a serious spaceflight issue, with silicone contamination being a particular concern. In an effort to understand on-orbit contamination of Materials International Space Station Experiment 8 (MISSE 8) flight samples and other International Space Station (ISS) payloads, contamination studies were conducted post-flight on retrieved Teflon fluorinated ethylene propylene (FEP) samples flown in the wake and nadir orientations on MISSE 8. The wake sample was Teflon FEP (M8-W11) flown as part of the Glenn MISSE 8 Polymers Experiment on the Optical Reflector Materials Experiment-III Ram/Wake (ORMatE-III R/W) tray and exposed to the LEO wake environment for 2.0 years. The nadir samples were silver-Teflon FEP radiator pieces taken from the MISSE 8 Single Events Upset Xilinx-Sandia Experiment II (SEUXSE II) Power Box and exposed to the LEO nadir environment for 2.14 years. The Teflon FEP flight materials were analyzed for changes in surface morphology and chemistry as compared to pristine control samples. The wake samples were also analyzed for changes in optical properties. There was no evidence of a molecular contamination layer present on the surface of the MISSE 8 wake or nadir facing Teflon FEP flight samples, although both the wake and nadir flight samples contained particulate contamination in some regions. The analyzed nadir particles were primarily zinc rich. The majority of analyzed wake particles were comprised of oxidized aluminum with small amounts of zinc and magnesium. The wake particles appear to have arrived early in the mission (or pre-flight) during a single event. This paper provides details of the MISSE 8 sample contamination analyses.

Erosion↗
DOE OSTI2020

Erratum to: Soft- and reactive landing of ions onto surfaces: concepts and applications

Soft- and reactive landing of mass-selected ions is gaining attention as a promising approach for the precisely-controlled preparation of materials on surfaces that are not amenable to deposition using conventional methods. A broad range of ionization sources and mass filters are available that make ion soft-landing a versatile tool for surface modification using beams of hyperthermal (<100?eV) ions. The ability to select the mass-to-charge ratio of the ion, its kinetic energy and charge state, along with precise control of the size, shape, and position of the ion beam on the deposition target distinguishes ion soft landing from other surface modification techniques. Soft- and reactive landing have been used to prepare interfaces for practical applications as well as precisely-defined model surfaces for fundamental investigations in chemistry, physics, and materials science. For instance, soft- and reactive landing have been applied to study the surface chemistry of ions isolated in the gas-phase, prepare arrays of proteins for high-throughput biological screening, produce novel carbon-based and polymer materials, enrich the secondary structure of peptides and the chirality of organic molecules, immobilize electrochemically-active proteins and organometallics on electrodes, create thin films of complex molecules, and immobilize catalytically active organometallics as well as ligated metal clusters. In addition, soft landing has enabled investigation of the size-dependent behavior of bare metal clusters in the critical subnanometer size regime where chemical and physical properties do not scale predictably with size. The morphology, aggregation, and immobilization of larger bare metal nanoparticles, which are directly relevant to the design of catalysts as well as improved memory and electronic devices, have also been studied using ion soft landing. This review article begins in section 1 with a brief introduction to the existing applications of ion soft- and reactive landing. Section 2 provides an overview of the ionization sources and mass filters that have been used to date for soft landing of mass-selected ions. A discussion of the competing processes that occur during ion deposition as well as the types of ions and surfaces that have been investigated follows in section 3. Section 4 discusses the physical phenomena that occur during and after ion soft landing, including retention and reduction of ionic charge along with factors that impact the efficiency of ion deposition. The influence of soft landing on the secondary structure and biological activity of complex ions is addressed in section 5. Lastly, an overview of the structure and mobility as well as the catalytic, optical, magnetic, and redox properties of bare ionic clusters and nanoparticles deposited onto surfaces is presented in section 6. © 2015 Wiley Periodicals, Inc. Mass Spec Rev 35:439–479, 2016.

Johnson, Grant E.↗
DOE OSTI2025

Bottlebrush Block Copolymer Thin Films

The self-assembly of block copolymers (BCPs) in thin films is governed by interfacial interactions (enthalpy) between the blocks and interfaces (at both the substrate and the surface). Advantage can also be taken of entropy to control the polymer orientation. Here, we synthesized a series of bottlebrush block copolymers (BBCPs), with deuterated polystyrene (DPS) as the core block and poly­(solketal acrylate) (PSA) as the corona block, where the backbone length (N BB) and grafting densities (GDs) were varied. The hydrophobic PSA block was converted to a hydrophilic poly­(glyceryl acrylate) (PGA) block by solid-state hydrolysis, bringing the BBCP from a disordered state into an ordered state with a lamellar microdomain morphology. The orientation of the morphology as a function of distance from the interfaces was systematically investigated by atomic force microscopy (AFM), interference microscopy, grazing-incidence small-angle X-ray scattering (GISAXS), and grazing-incidence small angle neutron scattering (GISANS). For N BB = 1 (diblock BCP), a mixed lamellar orientation was found. For N BB = 5 (star-like BBCP), a vertical orientation of the lamellar microdomains was found dominantly at the interfaces that propagated into the bulk of the film due to the entropic penalty associated with constraints on the junction points. Increasing the N BB to 50 (rod-like BBCP) and 100 (worm-like BBCP) yielded a random orientation, as the side chains became overcrowded when aligned in the same direction. By reducing the grafting density (GD) of a N BB = 50 BBCP from 100% to 75% and 50% by the incorporation of spacers into the backbone, the steric hindrance of side chains is reduced markedly, facilitating a vertical orientation of the lamellar microdomains. However, the vertical orientation becomes more random within the bulk of the thin film for different BBCP architectures. By modifying the substrate with a layer of PS, the preferential interactions between the core block of the BBCP and the interfaces induce a reconfiguration of the BBCP, drawing the core block out to contact substrate directly driven by enthalpy. Under these conditions, N BB = 5 showed a predominantly parallel orientation of the lamellar microdomains with the corona block minimizing contact with the substrate. Higher N BB values of 50 and 100 showed a more random orientation of the lamellar microdomains at different depths on the PS-modified substrate. Overall, thin-film morphology was regulated by tuning the configuration of the BBCP, varying the entropic contribution to the microdomain orientation.

Chen, Zhan↗
NASA NTRS2002

Development of a New Membrane Casting Apparatus for Studying Macrovoid Defects in Low-G

A new membrane-casting apparatus is developed for studying macrovoid defects in polymeric membranes made by the wet- and dry-casting process in low-gravity. Macrovoids are large (10-50 micron), open cavities interspersed among the smaller pores in the substructure under the gelled skin surface layer of the cast membrane. Although their occurrence is considered endemic to the wet- and dry-casting process since they can lead to compaction or skin rupture in the membrane process, recent studies suggest several useful applications such as transdermal and osmotic drug delivery systems, miniature bioreactors, etc. However, lack of knowledge about the macrovoid formation mechanism is an obstacle to further development of applications using them. An on-going debate is the role of the surface-tension-driven solutocapillary convection during macrovoid formation. The rapid growth of macrovoids within 1-5 seconds and the high polymer concentration in and near macrovoids make it difficult to explain the mechanism of macrovoid growth by diffusion alone, which is the widely accepted hypothesis proposed by Reuvers et al. The hypothesis advanced by our research group can explain this rapid growth via a mechanism that involves diffusion from the casting solution in the meta-stable region to the macrovoid enhanced by solutocapillary convection induced by the steep nonsolvent concentration gradient in the vicinity of the macrovoid. Since macrovoid growth is hypothesized to be the interplay of a solutocapillary-induced driving force counteracted by viscous drag and buoyancy, eliminate the latter provides a means for testing this hypothesis. Moreover, free convection mass transfer in the nonsolvent immersion bath used to cause phase-separation in membrane casting complicates developing a model for both the wet-casting process and macrovoid growth. The low-g environment minimizes gravitationally induced free convection thereby permitting a tractable solution to the ternary diffusion equations that characterize membrane formation. NASA's Parabolic Flight Research Aircraft provides a small window of low-g (approximately 25 s) that can be used to study macrovoid development in both wet- and dry-cast membranes if an appropriate casting apparatus is used. This casting apparatus should be able to cast the membrane in both low- and high-g in a manner so that essential one-dimensional mass transfer conditions are achieved to insure lateral uniformity in the membrane. The apparatus used in previous research on membrane casting in low-gravity was operated with the plunger driven mechanism. The spring-loaded plunger pushes the bottom block containing the polymer casting solution well directly under the absorbent chamber located in the upper stationary block. However, membranes made via this casting apparatus often displayed lateral nonuniformities that precluded obtaining quantitative information on the macrovoid growth process. Thus, it was necessary to determine the reason for these structural irregularities observed in the low-g casting apparatus. Both experimental as well as computer simulation studies of the low-g casting apparatus established that the impulsive action of the plunger caused the undesired structural nonuniformities. The simulation results showed that the width-to-depth aspect ratio of the shallow well that contains the casting solution in this apparatus was not an important factor in minimizing this problem. Even for a 40:1 (width : depth) aspect ratio, any convection induced by the horizontal motion of the interface of the casting solution will be damped out within 6.25x10(exp 4) seconds. However, the experimental studies revealed that the impulsive motion of the plunger caused a 'sloshing' of the casting solution that had to be eliminated. Therefore, the plungerdriven mechanism was changed to a cam-driven mechanism that did not cause any impulsive motion of the casting solution. Other refinements to this new membrane-casting apparatus include provision for removing the membranes from the casting wells in a less destructive manner. This was accomplished by using a slit geometry for the casting well that permitted disassembly for removal of the cast membrane. The materials used in the construction of this casting apparatus were chosen to insure wetting at the side walls and to maintain precise control of the thickness of the polymer solution in the casting well. An additional provision in this new casting apparatus is the ability to carry out both wet- as well as dry-casting. As such, this apparatus permitted the first studies of the wet-casting of polymeric membranes in low-g. Both wet- and dry-casting experiments on NASA's KC-135 research aircraft employing this new membrane-casting apparatus are scheduled in July 2002. The morphology of the resulting membranes will be characterized using an environmental scanning electron microscope (ESEM). The results of these low-g studies will be reported later.

Lee, Hanyong↗
DOE OSTI2022

Ionic Conductivity Enhancement of Polymer Electrolytes by Directed Crystallization

Here, we report that hot stretching of poly(ethylene oxide) (PEO)-based solid polymer electrolytes (SPEs) can lead to a preferred orientation of PEO crystalline lamellae, thereby reducing the tortuosity of the ion-conduction pathway along the thickness direction of the SPE film, causing improved ionic conductivity. The hot stretching method is implemented by stretching SPE films above the melting point of PEO in an inert environment followed by crystallization at room temperature while maintaining the applied strain. The effect of hot stretching on the crystalline orientation, crystallinity, morphology, and ion transport in PEO with two types of salts, lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) and lithium triflate (LiCF3SO3), is investigated in detail. Wide-angle X-ray scattering (WAXS) and small-angle X-ray scattering (SAXS) show that the orientation of PEO crystalline lamellae induces the formation of a short ion-conduction pathway along the through-plane direction of the SPE films, leading to 1.4- to 3.5-fold enhancement in the through-plane ionic conductivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Cation–polymer interactions and local heterogeneity determine the relative order of alkali cation diffusion coefficients in PEGDA hydrogels

Current research efforts are focused on endowing polymer membranes with ion–ion selectivity by incorporating ion–polymer interactions into materials to bias the selective partitioning and or diffusivity of one species over another. However, little is known about the impact of such interactions on the mechanisms of ion transport. In this study, we probe the influence of cation–polymer interactions on cation, anion, and salt diffusivity in a model membrane material, poly(ethylene glycol) diacrylate (PEGDA) by modeling concentrated polyethylene oxide solutions via molecular dynamics simulations. These results are compared to published experimental data for LiCl, NaCl, and KCl diffusion in PEGDA. Experimentally, the order of salt and cation diffusion coefficients for LiCl, NaCl, and KCl deviate from the order in aqueous solutions. Here, simulations identify these deviations to arise from cation–polymer coordination in the membrane. Both the fraction of bound cations and the average binding lifetime increases with decreasing cation hydration free energy (moving down the alkali series), leading to different diffusivity trends in the membrane compared to solution. However, to recover the experimentally observed order of diffusivities cations and salt in our simulations, we needed to incorporate membrane heterogeneity explicitly via a polymer charge scaling procedure. Together, our results indicate that cation–polymer interactions, as well as spatial heterogeneity within the membrane, play a critical role in dictating the observed order of alkali cation and salt diffusion coefficients in membranes.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Material Compatibility of 3D Printed Polymer Composites with Low GWP Refrigerants

The recent development of 3D printing brings numerous opportunities to develop polymer heat exchangers with desired configurations and allows access to the new complex engineering design for better performance. To be used in the HVAC&R system, the compatibility of these materials to refrigerants needs to be thoroughly investigated and understood. This study tested the material compatibility of the printed polymer composites according to the ASHRAE Guideline 38 using metal pressure vessels. These printed parts were tested with R-134A, R-1234YF, R-1234ZE, R-1233ZD(E), and 32-3 MAF POE (10 wt.%) was used as the lubricants. The change in volume, mass, hardness, and mechanical properties was studied in detail. Different compatibility of the composites with refrigerants was observed when the composition of the composite changed. After exposure to refrigerants, the morphological and thermal properties were studied with the scanning electron microscope, thermogravimetric analysis, and differential scanning calorimetry to further reveal the influence of these refrigerants.

Li, Kai↗
DOE OSTI2020

Thermodynamic Properties and Molecular Packing Explain Performance and Processing Procedures of Three D18:NFA Organic Solar Cells

Abstract Organic solar cells (OSCs) based on D18:Y6 have recently exhibited a record power conversion efficiency of over 18%. The initial work is extended and the device performance of D18‐based OSCs is compared with three non‐fullerene acceptors, Y6, IT‐4F, and IEICO‐4Cl, and their molecular packing characteristics and miscibility are studied. The D18 polymer shows unusually strong chain extension and excellent backbone ordering in all films, which likely contributes to the excellent hole‐transporting properties. Thermodynamic characterization indicates a room‐temperature miscibility for D18:Y6 and D18:IT‐4F near the percolation threshold. This corresponds to an ideal quench depth and explains the use of solvent vapor annealing rather than thermal annealing. In contrast, D18:IEICO‐4Cl is a low‐miscibility system with a deep quench depth during casting and poor morphology control and low performance. A failure of ternary blends with PC 71 BM is likely due to the near‐ideal miscibility of Y6 to begin with and indicates that strategies for developing successful ternary or quaternary solar cells are likely very different for D18 than for other high‐performing donors. This work reveals several unique property–performance relations of D18‐based photovoltaic devices and helps guide design or fabrication of yet higher efficiency OSCs.

Wang, Zhen↗
DOE OSTI2025

Morphogenic Growth 3D Printing

Inspired by nature's morphogenesis, a new 3D printing process –growth printing (GP)– takes advantage of a self‐propagating curing front to produce 3D polymeric parts following a growth‐like development plan. The propagation of the curing front is driven by the exothermic polymerization of dicyclopentadiene (DCPD), which transforms the liquid resin into a stiff polymer as it propagates at 1 mm s −1 . GP is triggered when a heated initiator contacts the uncured liquid resin in an open container. The initiator nucleates the frontal polymerization reaction and the isotropic radial propagation of the growth front. Simultaneously, the initiator is moved up across the free surface of the resin, pulling the cured object out of the uncured resin. The motion trajectory of the initiator with respect to the free resin surface controls the growth morphology of the 3D part. An inverse design algorithm is developed to produce 3D parts by modeling the reaction‐diffusion‐driven solidification process. This process has substantial energy savings and high printing speeds.

3D printing↗
DOE OSTI2023

Revealing Deformation Mechanisms in Polymer-Grafted Thermoplastic Elastomers via In Situ Small-Angle X-ray Scattering

The tunable properties of thermoplastic elastomers (TPEs), through polymer chemistry manipulations, enable these technologically critical materials to be employed in a broad range of applications. The need to “dial-in” the mechanical properties and responses of TPEs generally requires the design and synthesis of new macromolecules. In these designs, TPEs with nonlinear macromolecular architectures outperform the mechanical properties of their linear copolymer counterparts, but the differences in the deformation mechanism providing enhanced performance are unknown. Here, in situ small-angle X-ray scattering (SAXS) measurements during uniaxial extension reveal distinct deformation mechanisms between a commercially available linear poly(styrene)–poly(butadiene)–poly(styrene) (SBS) triblock copolymer and the grafted SBS version containing grafted poly(styrene) (PS) chains from the poly(butadiene) (PBD) midblock. The neat SBS (φ SBS = 100%) sample deforms congruently with the macroscopic dimensions, with the domain spacing between spheres increasing and decreasing along and transverse to the stretch direction, respectively. At high extensions, end segment pullout from the PS-rich domains is detected, which is indicated by a disordering of SBS. Conversely, the PS-grafted SBS that is 30 vol % SBS and 70% styrene (φ SBS = 30%) exhibits a lamellar morphology, and in situ SAXS measurements reveal an unexpected deformation mechanism. During deformation, there are two simultaneous processes: significant lamellar domain rearrangement to preferentially orient the lamellae planes parallel to the stretch direction and crazing. The samples whiten at high strains as expected for crazing, which corresponds with the emergence of features in the 2D SAXS pattern during stretching consistent with fibril-like structures that bridge the voids in crazes. The significant domain rearrangement in the grafted copolymers is attributed to the new junctions formed across multiple PS domains by the grafting of a single chain. In conclusion, the in situ SAXS measurements provide insights into the enhanced mechanical properties of grafted copolymers that arise through improved physical cross-linking that leads to nanostructure domain reorientation for self-reinforcement and craze formation where fibrils help to strengthen the polymer.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Crosslinked metallo-polyelectrolytes with enhanced flexibility and dimensional stability for anion-exchange membranes

High-performing anion-exchange membranes (AEMs) have attracted tremendous interest for applications in emerging energy storage and conversion devices. In this work, we present a strategy for the synthesis of crosslinked metallo-polyelectrolytes as mechanically flexible, dimensionally stable and ionically conductive AEMs. The water uptake and swelling ratio are suppressed remarkably by introducing a crosslinked polymeric network. The as-prepared membranes also exhibit excellent thermal stability. The phase-separated morphology allows rapid ion-transport with low water uptake at various temperatures. Specifically, a conductivity of 53.3 mS cm -1 at 80 °C was achieved with an ion exchange capacity of 1.07 mmol g -1 and a low swelling ratio of 13%.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Deciphering supramolecular and polymer-like behavior in metallogels: real-time insights into temperature-modulated gelation and rapid self-assembly dynamics

Bis(pyridyl) urea-based gelators, namely L2 and its isomeric mixture ( L1 + L2 ), are known to self-assemble into 1D architectures capable of inducing supramolecular gelation. Coordination with metal ions such as Ag( I ), Cu( II ), and Fe( III ) introduces structural reinforcement, enabling the formation of distinct 3D networks governed by metal-specific coordination geometries. Here, we present a comprehensive investigation into the temperature-responsive behavior (20–60 °C) of L2 and L1 + L2 , both in the absence and presence of Ag( I ), Dy( III ), Fe( III ), Cu( II ), and Ho( III ), using real-time small-angle neutron scattering (SANS). To probe long-term structural evolution/kinetics of self-assembly, real-time small-angle X-ray scattering (SAXS) was employed on L2 + Ag gels, complemented by differential scanning calorimetry (DSC) to evaluate thermal transitions. Our results reveal strikingly divergent gelation behaviors: L2 forms a highly rigid, covalent polymer-like network, while L1 + L2 exhibits remarkable thermal adaptability. Upon metal coordination, the assemblies exhibit pronounced crystallinity and exceptional thermal stability, as evidenced by persistent Bragg reflections and invariant d-spacings. Intriguingly, L2 : Fe (2 : 1) and L1 : L2 : Fe (0.5 : 0.5 : 1) in acetonitrile-d 3 (ACN-d 3 ) deviate from this trend, forming thermally labile amorphous gels. These systems show a complete loss of crystalline order, reduced Porod exponents—indicative of collapsed or branched fiber morphologies—and prominent melting and glass transition events in DSC. Fitting SANS and SAXS data to the correlation length model unveiled insightful nanostructural features. While most systems displayed minimal temperature-induced variation in mesh size or surface morphology, L2 : Ag in dimethyl sulfoxide-d 6 (DMSO-d 6 )/D 2 O and L2 : Fe (1 : 1) in ACN-d 3 exhibited a rare combination of thermally stable correlation lengths and increasing high- q exponents—strongly suggesting progressive fiber densification or surface smoothing within a robust gel framework. These findings highlight the tunability and structural resilience of supramolecular gels through precise control of ligand architecture, metal coordination, and temperature, offering valuable design principles for functional soft materials.

Pajoubpong, Jinnipha [Univ. of Cincinnati, OH (Uni↗
DOE OSTI2022

Two Neptunium(III) Mellitate Coordination Polymers: Completing the Series Np–Cf of Trans-Uranic An(III) Mellitates

For this work, two neptunium(III) mellitates, 237 Np 2 (mell)(H 2 O) 9 ·1.5H 2 O (Np-1α) and 237 Np 2 (mell)(H 2 O) 8 ·2H 2 O (Np-1β), have been synthesized from 237 NpCl 4 (dme) 2 by reduction with KC 8 and subsequent reaction with an aqueous solution of mellitic acid (H 6 mell). Characterization by single-crystal X-ray crystallography and UV–vis–NIR spectroscopy confirms that the neptunium is in its +3 oxidation state and both polymorphs are isostructural to the previously reported plutonium mellitates. Of the two morphologies, Np-1α is indefinitely stable in air, while Np-1β slowly oxidizes over several months. This is due to the change in the energy of the metal-ligand charge-transfer absorption exhibited by these compounds attributed to differing numbers of carboxylate bonds to Np(III), where in Np-1β the energy is low enough to result in spontaneous oxidation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS2003

Development of a nanostructured DNA delivery scaffold via electrospinning of PLGA and PLA-PEG block copolymers

The present work utilizes electrospinning to fabricate synthetic polymer/DNA composite scaffolds for therapeutic application in gene delivery for tissue engineering. The scaffolds are non-woven, nano-fibered, membranous structures composed predominantly of poly(lactide-co-glycolide) (PLGA) random copolymer and a poly(D,L-lactide)-poly(ethylene glycol) (PLA-PEG) block copolymer. Release of plasmid DNA from the scaffolds was sustained over a 20-day study period, with maximum release occurring at approximately 2 h. Cumulative release profiles indicated amounts released were approximately 68-80% of the initially loaded DNA. Variations in the PLGA to PLA-PEG block copolymer ratio vastly affected the overall structural morphology, as well as both the rate and efficiency of DNA release. Results indicated that DNA released directly from these electrospun scaffolds was indeed intact, capable of cellular transfection, and successfully encoded the protein beta-galactosidase. When tested under tensile loads, the electrospun polymer/DNA composite scaffolds exhibited tensile moduli of approximately 35 MPa, with approximately 45% strain initially. These values approximate those of skin and cartilage. Taken together, this work represents the first successful demonstration of plasmid DNA incorporation into a polymer scaffold using electrospinning.

Non-NASA Center↗
DOE OSTI2020

Ultrastructure of Critical-Gel-like Polyzwitterion–Polyoxometalate Complex Coacervates: Effects of Temperature, Salt Concentration, and Shear

The structure of unconventional complex coacervates, such as polymer-nonpolymer complex coacervates, remains less investigated than that of the conventional coacervates formed between oppositely charged polyelectrolytes with symmetric charge species. Yet, their microscopic structural organization is important to further elucidate the mechanism of liquid-liquid-phase separation processes upon complexation. In this work, we characterize the microstructural organization of complex coacervates formed between inorganic polyoxometalate (POM) and polyzwitterion by small-angle X-ray scattering (SAXS) with in situ temperature and shear control. Furthermore, despite the apparent transparent and homogeneous morphology of dense coacervates as observed by optical microscopy, our previous results (Macromolecules 2018, 51, 22, 9405-9411) suggest that dense polyzwitterion-POM coacervates exhibit critical-gel-like networks containing both complex-poor region (mesh pore) and complex-rich region (connective network). SAXS results as reported in this work support that the complex-rich region is actually in the form of loosely packed POM aggregates linked by polyzwitterion, designated as complex particles. The structure of aggregating complex particles is further examined against varied composition and salt concentrations, temperature, and shear, thanks to the high X-ray scattering contrast of POMs from that of other components in the coacervates. The complex particles in the dense coacervates appear to grow with more tightly packed POM aggregates with increasing POM-to-polyzwitterion concentration ratio, in contrast to more loosely packed POM aggregates with decreasing salt concentration. Conversely, increasing temperature could result in smaller complex particles containing more loosely packed POM aggregates, consistent with temperature-dependent viscoelasticity of dense coacervates. Furthermore, such POM-based hybrid dense coacervates exhibit intriguing strain-hardening behavior, resulting from shear-enhanced POM packing inside the complex particles. Distinct from the shear-thinning behavior of most conventional crosslinked polymeric networks, the strain-hardening property combined with thermal- and salt-responsive characteristics of polyzwitterion-POM coacervates could broaden the applications of hybrid organic-inorganic macroion coacervates as smart functional materials working under extreme environmental conditions.

36 MATERIALS SCIENCE↗