Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PNEUMATICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

Laboratory study of the effects of sidewall treatment, source directivity and temperature on the interior noise of a light aircraft fuselage

This paper describes a laboratory study of add-on {coustic treatments for a twin-engine, propeller-driven aircraft fuselage. The sound source was a pneumatic-driver, with attached horn to simulate propeller noise distribution, powered by a white noise signal. Treatments included a double-wall, production-line treatment and various fiberglass and lead-vinyl treatments. Insertion losses, space-averaged across six interior microphone positions, were used to evaluate the treatments. In addition, the effects of sound source angle and ambient temperature on interior sound pressure level are presented. The sound source angle is shown to have a significant effect on one-third octave band localized sound pressure level. While changes in ambient temperature are shown to have little effect on one-third octave band localized sound pressure level, the change in narrowband localized sound pressure level may be dramatic.

Heitman, K. E.↗

Formation and characterization of simulated small droplet icing clouds

Two pneumatic two-fluid atomizers operating at high liquid and gas pressures produced water sprays that simulated small droplet clouds for use in studying icing effects on aircraft performance. To measure median volume diameter, MVD or D sub v.5, of small droplet water sprays, a scattered-light scanning instrument was developed. Drop size data agreed fairly well with calculated values at water and nitrogen pressures of 60 and 20 psig, respectively, and at water and nitrogen pressures of 250 and 100 psig, respectively, but not very well at intermediate values of water and nitrogen pressure. MVD data were correlated with D sub O, W sub N, and W sub w, i.e., orifice diameter, nitrogen, and water flowrate, respectively, to give the expression for MVD in microns.

Ingebo, R. D.↗

Characterization of simulated small-droplet fuel sprays

A two-fluid pneumatic atomizer operating at relatively high liquid and gas pressures produced water sprays that simulated small-droplet clouds of liquid fuel for use in studying vaporization and fuel-air mixing effects on combustor performance and emissions. To characterize the sprays, a scattered-light scanning instrument was developed and measurements of volume median or volume mean diameter, D sub V.5, were correlated with D sub O, W sub w, and W sub n, i.e., orifice diameter, water, and nitrogen gas flow rates, respectively, to give the general expression: D sub v.5 approx. (D sub O sup 0.2) (W sub w sup m) (W sub n sup n), which yields D sub v.5 = 45 (D sub o sup 0.2) (W sub w sup 0.2) (W sub w sup -1.2). Values of D sub 0, W sub w, and W sub n are in centimeters and grams/second, respectively. Farther downstream at an axial distance of 6.7 cm, exponent m increased from 0.2 to 0.4 and exponent n decreased from -1.2 to -1.0 and at a distance of 25 cm downstream of the atomizer, n decreased to -0.8. The increase in exponent m and decrease in exponent n was attributed to a loss of very small droplets from the spray due primarily to vaporization and diffusion effects on clouds of small droplets traveling a distance of 25 cm.

Ingebo, R. D.↗

Large-scale static investigation of circulation-control-wing concepts applied to upper surface-blowing aircraft

The use of a circulation control to deflect turbofan engine thrust beyond 90 deg. has been proven in full-scale static ground tests of the circulation-control-wing/upper-surface-blowing (CCW/USB) concept. This powered high-lift system employs a circular, blown trailing edge to replace the USB mechanical flaps to entrain engine-exhaust flow, and to obtain both a vertical-thrust component and an augmented circulation lift for short takeoff and landing (STOL) applications. Previous tests (Phase 1), done in 1982, of a basic configuration installed on the Quiet Short Haul Research Aircraft confirmed these CCW/USB systems capabilities. A second phase (Phase 2) of full-scale, static, thrust-deflection investigations has reconfirmed the ability to deflect engine thrust from 40 to 102 deg., depending on thrust level. Five new configurations were evaluated and performance improvements noted for those configurations with larger blown span, fences or favorable engine interactions, smaller slot height, and larger radii with less than 180 deg. of CCW surface arc. In general, a 90 deg. circular arc with a smaller slot height provided the best performance, demonstrating that adequate thrust turning can be produced by a trailing-edge shape which may have minimal cruise-performance penalty. Thrust deflections were achieved at considerably lower blowing momentum than was required for the baseline case of Phase 1. Improved performance and versatility were thus confirmed for the CCW/USB system applied to STOL aircraft, where the potential for developing a non-moving-parts pneumatic thrust deflector to rapidly vary horizontal force from thrust to drag, while maintaining constant vertical force, appears quite promising. The conversion from high-lift to lower-drag cruise mode by merely terminating the blowing provides an effective STOL aircraft system.

Shovlin, M. D.↗

Design and development of a large diameter high pressure fast acting propulsion valve and valve actuator

The design and development of a large diameter high pressure quick acting propulsion valve and valve actuator is described. The valve is the heart of a major test facility dedicated to conducting full scale performance tests of aircraft landing systems. The valve opens in less than 300 milliseconds releasing a 46-centimeter- (18-in.-) diameter water jet and closes in 300 milliseconds. The four main components of the valve, i.e., valve body, safety shutter, high speed shutter, and pneumatic-hydraulic actuator, are discussed. This valve is unique and may have other aerospace and industrial applications.

Srinivasan, K. V.↗

Flowfield measurements in a separated and reattached flat plate turbulent boundary layer

The separation and reattachment of a large-scale, two-dimensional turbulent boundary layer at low subsonic speed on a flat plate has been studied experimentally. The separation bubble was 55 cm long and had a maximum bubble thickness, measured to the height of the mean dividing streamline, of 17 cm, which was twice the thickness of the inlet boundary layer. A combination of laser velocimetry, hot-wire anemometry, pneumatic probing techniques, and flow visualization were used as diagnostics. Principal findings were that an outer inviscid rotational flow was defined which essentially convected over the blockage associated with the inner, viscously dominated bubble recirculation region. A strong backflow region in which the flow moved upstream 100 percent of the time was measured near the test surface over the central 35 percent of the bubble. A laminar backflow boundary layer having pseudo-turbulent characteristics including a log-linear velocity profile was generated under the highly turbulent backflow. Velocity profile shapes in the reversed flow region matched a previously developed universal backflow profile at the upstream edge of the separation region but not in the steady backflow region downstream. A smoke flow visualization movie and hot-film measurements revealed low frequency nonperiodic flapping at reattachment. However, forward flow fraction data at reattachment and mean velocity profiles in the redeveloping boundary layer downstream of reattachment correlated with backward-facing step data when the axial dimension was scaled by the distance from the maximum bubble thickness to reattachment.

Patrick, William P.↗

The mission configuration process for the Spartan attitude control system

The Spartan attitude control system (ACS) control electronics assembly cold plate has a standard connector interface to the rest of the Spartan payload and ground equipment. The connectors carry gyro signals, optical sensor signals, the experiment interface, the gas command decoder interface, and a pneumatics interface. Different flights can employ different optical sensor complements; the ACS engineer must accordingly connect the sensor error signals to the proper pins and connectors on the ACS electronics.

Stone, R. W.↗

M.I.T./Canadian vestibular experiments on the Spacelab-1 mission. V - Postural responses following exposure to weightlessness

The four science crewmembers of Spacelab-1 were tested for postural control before and after a 10 day mission in weightlessness. Previous reports have shown changes in astronaut postural behavior following a return to earth's 1-g field. This study was designed to identify changes in EMG latency and amplitudes that might explain the instabilities observed post-flight. Erect posture was tested having the subject stand on a pneumatically driven posture platform which pitched rapidly and unexpectedly about the ankles causing dorsi- and plantarflexion. Electromyographic (EMG) activity from the tibialis anterior and the gastrocnemius-soleus muscles was measured during eyes open and eyes closed trials. The early (pre 500 ms) EMG response characteristics (latency, amplitude) in response to a disturbance in the posture of the subject were apparently unchanged by the 10 days of weightlessness. However, the late (post 500 ms) response showed higher amplitudes than was found pre-flight. General postural control was quantitatively measured pre- and post-flight by a 'sharpened Romberg Rails test'. This test showed decrements in standing stability with eyes closed for several days post-flight.

Kenyon, R. V.↗

An electronic scanner of pressure for wind tunnel models

An electronic scanner of pressure (ESOP) has been developed by NASA Ames Research Center for installation in wind tunnel models. An ESOP system consists of up to 20 pressure modules (PMs), each with 48 pressure transducers and a heater, an analog-to-digital (A/D) converter module, a microprocessor, a data controller, a monitor unit, a control and processing unit, and a heater controller. The PMs and the A/D converter module are sized to be installed in the models tested in the Ames Aerodynamics Division wind tunnels. A unique feature of the pressure module is the lack of moving parts such as a pneumatic switch used in other systems for in situ calibrations. This paper describes the ESOP system and the results of the initial testing of the system. The initial results indicate the system meets the original design goal of 0.15 percent accuracy.

Kauffman, Ronald C.↗

Balloon Holds X-Ray Film In Position

Simple pneumatic apparatus holds x-ray film against inside wall of tube or cavity. Balloon expanded against confines of cavity to push x-ray film against inner wall. With assurance that x-ray image formed at wall, position of defect calculated accurately.

Bezaire, Joseph C.↗

The impact of circulation control on rotary aircraft controls systems

Application of circulation to rotary wing systems is a new development. Efforts to determine the near and far field flow patterns and to analytically predict those flow patterns have been underway for some years. Rotary wing applications present a new set of challenges in circulation control technology. Rotary wing sections must accommodate substantial Mach number, free stream dynamic pressure and section angle of attack variation at each flight condition within the design envelope. They must also be capable of short term circulation blowing modulation to produce control moments and vibration alleviation in addition to a lift augmentation function. Control system design must provide this primary control moment, vibration alleviation and lift augmentation function. To accomplish this, one must simultaneously control the compressed air source and its distribution. The control law algorithm must therefore address the compressor as the air source, the plenum as the air pressure storage and the pneumatic flow gates or valves that distribute and meter the stored pressure to the rotating blades. Also, mechanical collective blade pitch, rotor shaft angle of attack and engine power control must be maintained.

Kingloff, R. F.↗

Effect of mass-velocity on liquid jet atomization in Mach 1 gasflow

Interacting two-phase flow in four differently sized pneumatic two-fluid atomizers was investigated to determine the effect of gas mass-velocity on the Sauter mean diameter of sprays produced by small diameter liquid jets breaking up in high velocity gas flow. Tests were conducted primarily in the acceleration-wave regime for liquid jet atomization, where it was found that the loss of droplets due to vaporization had a marked effect on drop size measurements. A scattered-light scanner, developed at NASA Lewis Research Center, was used to measure the Sauter mean diameter, D sub 32, which was correlated with nitrogen gas mass-velocity to give the following expression: D (sup -1)(sub 32) = 11.7(rho (sub n) V (sub n)) (sup 1.33). The exponent 1.33 for the gas mass-velocity is identical to that predicted by atomization theory for liquid jet breakup in the acceleration-wave regime.

Ingebo, Robert D.↗

Small-droplet spray measurements with a scattered-light scanner

Interacting two-phase flow through pneumatic two-fluid nozzles was investigated to determine the effect of nitrogen gas mass-velocity on the Sauter mean diameter of water sprays produced by the breakup of small diameter liquid-jets in high velocity gas streams. Tests were conducted primarily in the aerodynamic-stripping regime of liquid-jet atomization. It was found that the loss of droplets due to vaporization and dispersion had a marked effect on drop size measurements. A scattered-light scanner, developed at NASA Lewis Research Center was used to measure Sauter mean diameters, D sub 32, as small as 5 microns, which were correlated with nitrogen gas mass-velocity to give the following expression: D(sup -1)(sub 32) = 11.7(rho (sub n) V(sub n))(sup 1.33) where D sub 32 and p(sub n)V(sub n) are given in centimeters and g/sq cm-sec, respectively. The exponent 1.33 is the same as that predicted by atomizing theory for liquid-jet breakup in high velocity gas streams.

Ingebo, Robert D.↗

Aerodynamics in ground effect and predicted landing ground roll of a fighter configuration with a secondary-nozzle thrust reverser

An experimental investigation of the in-ground effect aerodynamic characteristics and predicted landing-ground-roll performance of wing-canard fighter configuration with a secondary nozzle thrust reverser was completed. These tests were conducted in the Langley 14 by 22 foot Subsonic Wind Tunnel using a model equipped with a pneumatic jet for thrust simulation of nozzle pressure ratios up to 4.0. The model was tested in the landing rollout configuration at approx. wheel touchdown height for a range of decreasing dynamic pressure from 50 psf down to 10 psf. Landing-ground-roll predictions of the configuration were calculated using the wind tunnel results.

Banks, Daniel W.↗

Design of low Reynolds number airfoils. II

Low Reynolds number airfoils were designed for high lift-to-drag ratios. Design considerations of low Re-airfoils are discussed and design examples are presented. It is shown that the performance of advance low Reynolds airfoils critically depends on proper laminar separation and transition control for the minimum profile drag coefficient with minimum turbulator device drag. This transition control close to the laminar separation is possible by enforcing transition on the upper surface either directly by means of spanwise rows of three-dimensional roughness elements, bleed or suction holes, or indirectly by means of destabilizing the upper surface boundary layer by means of backward facing surface steps, two-dimensional or zig-zag tapes or weak boundary layer blowing. Pneumatic turbulators are found to be advantageous because they can be adjusted to different external flow conditions better than mechanical ones.

Pfenninger, W.↗

Tethered Remote Manipulator

Remote-manipulator concept for retrieval or inspection of objects in outer space applied to underwater or in tanks of hazardous chemicals. System includes tether head on outer end of tether cable wound on motor-driven takeup reel. Head includes mounting plate with four canted thrustors facing rearward, solid-state camera with patterned sources of light facing forward, and pneumatic inflatable end effector. Also includes device to cut head loose in emergency. Intended for use in places beyond reach of jointed rigid-arm manipulator and where unsafe or impractical to send humans.

Bryan, Thomas C.↗

Inductively-Activated Short-Interval Timer

Timing circuit in pneumatically launched projectile triggers explosive charge in projectile at specified delay after launch. Both power and control signals coupled inductively to timer from stationary launcher circuitry. Eliminates need for direct electrical contacts, which are unreliable and generate sparks that trigger explosive accidentally. Inductive coupling also provides higher reliability in field operation than contacts. Concept useful in such other safety-related applications as remotely or automatically controlling flow of bottled flammable gas.

Wiker, Gordon A.↗

Gas density effect on dropsize of simulated fuel sprays

Two-phase flow in pneumatic two-fluid fuel nozzles was investigated experimentally to determine the effect of atomizing-gas density and gas mass-flux on liquid-jet breakup in sonic-velocity gas-flow. Dropsize data were obtained for the following atomizing-gases: nitrogen; argon; carbon dioxide; and helium. They were selected to cover a gas molecular-weight range of 4 to 44. Atomizing-gas mass-flux ranged from 6 to 50 g/sq cm-sec and four differently sized two-fluid fuel nozzles were used having orifice diameters that varied from 0.32 to 0.56 cm. The ratio of liquid-jet diameter to SMD, D sub o/D sub 32, was correlated with aerodynamic and liquid-surface forces based on the product of the Weber and Reynolds number, We*Re, and gas-to-liquid density ratio, rho sub g/rho sub l. To correlate spray dropsize with breakup forces produced by using different atomizing-gases, a new molecular-scale dimensionless group was derived. The derived dimensionless group was used to obtain an expression for the ratio of liquid-jet diameter to SMD, D sub o/D sub 32. The mathematical expression of this phenomenon incorporates the product of the Weber and Reynolds number, liquid viscosity, surface tension, acoustic gas velocity, the RMS velocity of gas molecules, the acceleration of gas molecules due to gravity, and gas viscosity. The mathematical expression encompassing these parameters agrees well with the atomization theory for liquid-jet breakup in high velocity gas flow. Also, it was found that at the same gas mass-flux, helium was considerably more effective than nitrogen in producing small droplet sprays with SMD's in the order of 5 micrometers.

Ingebo, Robert D.↗