Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PINS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Repairing pin-fin cold plates

Inexpensive technique avoids high temperatures that deform thin stainless steel plates. Because repair disks have small diameters, repaired area can sustain greater loads that larger unsupported areas of faceplate.

Ruppe, E. P.↗
NASA NTRS1977

Small-signal gain diagnostic measurements in a flowing CO2 pin discharge laser

Small-signal gain diagnostic measurements were conducted on closed loop, high power, carbon dioxide laser to assess the coupling between gas flow velocity and resonator saturation. Parameters investigated included optical cavity and discharge power. Results of gain measurements within and downstream of the excitation volume are presented for a laser gas composition He:N2:CO2 of 10:7:1 at 90 torr. The gain at constant discharge power was observed to be dependent upon discharge power level and time. An important result of this study is that the effects of gain swept downstream of the discharge region must be considered in the resonator design if efficient extraction of stored optical energy is desired.

Blech, R. A.↗
NASA NTRS1982

Load-Displacement Measurement on Pin-Loaded Specimens

Tubes apply as displacement is registered by long armed, double-cantilever gage. Sharp points at ends of arms protrude through holes in tube walls and contact center of area of load applications. Method was devised for determining load point displacement accurately. No extraneous displacement fraction is present in measurement, and data-correction procedures are unnecessary.

Fisher, D. M.↗
NASA NTRS1983

Repairing Loose Connector Pins

In repair procedure, hypodermic needle applies epoxy adhesive in and behind cavity containing damaged locking finger. Damaged connector does not have to be demated or removed from harness to apply epoxy.

Dean, W. T., III↗
NASA NTRS1987

Supports for Wires Soldered to Pins

Stress concentrations reduced by reorienting wires. New solder-joint configuration provides support for part of wire most susceptible to damage from handling or vibration part next to solder joint. Reversal of wire and heat-shrinkable tubing reduce stress in this region.

Hill, Arthur J.↗
NASA NTRS1989

Channelized coplanar waveguide pin-diode switches

Three different types of p-i-n diode, reflective CPW switches are presented. The first two switches are the series and the shunt mounted diode switches. Each has achieved greater than 15 dB of isolation over a broad bandwidth. The third switch is a narrow band, high isolation switched filter which has achieved 19 dB of isolation. Equivalent circuits and measured performance for each switch is presented.

Ponchak, G. E.↗
NASA NTRS1990

Pinning, flow and plastic deformation of flux vortices in high T(sub c) superconductors

In high temperature superconductor (HTSC) materials the vortices are highly mobile and flexible. This is reflected in different models of melt of a vortex lattice. Another aspect of the problem is stressed: an easy nucleation and high mobility of dislocations in the vortex lattice. Some models of plastic deformation of vortex lattice are considered as a result of its interaction with a real crystal structure. Depinning is interpreted as yield of plastic flow is vortex medium. Effect of macroscopic defects in crystal structures (pores, inclusions, grain and domain boundaries) is being considered in detail. Available experimental facts on magnetization and a critical current in HTSC and conventional superconductors are discussed from the points of view of depinning to vortices vs. plastic flow of vortices vs. plastic flow of vortices medium.

Roytburd, A.↗
NASA NTRS1986

Energy efficient engine pin fin and ceramic composite segmented liner combustor sector rig test report

Under the NASA-sponsored Energy Efficient Engine program, Pratt and Whitney has successfully completed a comprehensive test program using a 90-degree sector combustor rig that featured an advanced two-stage combustor with a succession of advanced segmented liners. Building on the successful characteristics of the first generation counter-parallel Finwall cooled segmented liner, design features of an improved performance metallic segmented liner were substantiated through representative high pressure and temperature testing in a combustor atmosphere. This second generation liner was substantially lighter and lower in cost than the predecessor configuration. The final test in this series provided an evaluation of ceramic composite liner segments in a representative combustor environment. It was demonstrated that the unique properties of ceramic composites, low density, high fracture toughness, and thermal fatigue resistance can be advantageously exploited in high temperature components. Overall, this Combustor Section Rig Test program has provided a firm basis for the design of advanced combustor liners.

Dubiel, D. J.↗
NASA NTRS1991

Algebraic grid generation for coolant passages of turbine blades with serpentine channels and pin fins

In order to study numerically details of the flow and heat transfer within coolant passages of turbine blades, a method must first be developed to generate grid systems within the very complicated geometries involved. In this study, a grid generation package was developed that is capable of generating the required grid systems. The package developed is based on an algebraic grid generation technique that permits the user considerable control over how grid points are to be distributed in a very explicit way. These controls include orthogonality of grid lines next to boundary surfaces and ability to cluster about arbitrary points, lines, and surfaces. This paper describes that grid generation package and shows how it can be used to generate grid systems within complicated-shaped coolant passages via an example.

Shih, T. I.-P.↗
NASA NTRS1993

Pyrotechnic modeling for the NSI and pin puller

A discussion concerning the modeling of pyrotechnically driven actuators is presented in viewgraph format. The following topics are discussed: literature search, constitutive data for full-scale model, simple deterministic model, observed phenomena, and results from simple model.

Powers, Joseph M.↗
NASA NTRS1994

A study of a multi-pinned phase CCD detector for use as a star tracker

This grant has supported studies of the use of charge coupled devices (CCD's) in star trackers in a number of different areas. Among the tasks we have pursued are the following: (1) radiation modeling and the increase in noise equivalent angle as a result of exposure to protons and bremsstrahlung gamma rays; (2) the development of pattern matching software to identify field locations from a CCD image and a pre-existing map of the local area; (3) observations of various stellar fields from the 24 inch telescope at the Offit Observatory at JHU, primarily to test the pattern matching software (these included crowded fields as well as moving objects, like comets); and (4) tracking of very faint objects to determine the faint limit of the CCD system.

Friedman, Scott D.↗
NASA NTRS2005

Performance Enhancement Using Selective Reinforcement for Metallic Single- and Multi-Pin Loaded Holes

An analysis based investigation of aluminum with metal matrix composite selectively reinforced single- and multi-hole specimens was performed and their results compared with results from geometrically comparable non-reinforced specimens. All reinforced specimens exhibited a significant increase in performance. Performance increase of up to 170 percent was achieved. Specimen failure modes were consistent with results from reinforced polymeric matrix composite specimens. Localized reinforcement application (circular) proved as effective as a broader area (strip) reinforcement. Also, selective reinforcement is an excellent method of increasing the performance of multi-hole specimens.

Farley, Gary L.↗
NASA NTRS2010

Large-Format AlGaN PIN Photodiode Arrays for UV Images

A large-format hybridized AlGaN photodiode array with an adjustable bandwidth features stray-light control, ultralow dark-current noise to reduce cooling requirements, and much higher radiation tolerance than previous technologies. This technology reduces the size, mass, power, and cost of future ultraviolet (UV) detection instruments by using lightweight, low-voltage AlGaN detectors in a hybrid detector/multiplexer configuration. The solar-blind feature eliminates the need for additional visible light rejection and reduces the sensitivity of the system to stray light that can contaminate observations.

Aslam, Shahid↗