Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PHASE STUDIES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

Enhanced phase segregation induced by dipolar interactions in polymer blends

We present a generalized theory for studying phase separation in polymer blends containing dipoles on their backbone. The theory is used to construct co-existence curves and study the effects of dipolar interactions on interfacial tension for a planar interface between the coexisting phases. It is shown that mismatch in monomeric dipole moments leads to destabilization of homogeneous phase. Corrections to the Flory-Huggins phase diagram are predicted using the theory. Furthermore, it is found that interfacial tension increases with an increase in the mismatch. Density profiles and interfacial tensions are constructed for diffuse and sharp polymer-polymer interfaces by extending Cahn-Hilliard and Helfand-Tagami-Sapse s treatment, respectively. Correlating dipole moments with the dielectric constant of pure phases, it is demonstrated that effects of mismatch between the dipole moments of the two monomers is equivalent to the dielectric mismatch between the polymers.

Kumar, Rajeev↗

Almost perfect in-phase and anti-phase chaotic and periodic phase synchronization in large arrays of diode lasers

In this paper we study phase synchronization in large arrays of weakly coupled single mode semiconductor laser diodes. We show that if the coupling topology is chosen appropriately, the laser array exhibits robust phase synchrony (including chaotic and non-chaotic phase synchrony). Furthermore, one can define coupling topologies that lead to chaotic anti-phase synchronization. To the best of our knowledge, chaotic anti-phase synchronization has not been observed in large arrays of coupled nonlinear oscillators. Additionally, when diodes are coupled via a decayed non-local coupling scheme, the leading spatial mode can be stable. This leads to an almost-perfect phase synchronous state where the phases are synchronized, but the system is not set exactly on the synchronization manifold. This almost-perfect phase synchronous state is robust to noise and frequency disorder and can be realized under periodic (fixed-intensity limit cycle) continuous-wave and chaotic behavior. The presented result is an example of the broader phenomenon of linear transverse mode selection taking place in a coupled oscillator system with nonlinear dynamics.

47 OTHER INSTRUMENTATION↗

Postclosure Criticality Consequence Analysis - Scoping Phase

Commercial generation of energy via nuclear power plants in the United States (U.S.) has generated thousands of metric tons of spent nuclear fuel (SNF), the disposal of which is the responsibility of the U.S. Department of Energy (DOE) (Nuclear Waste Policy Act of 1982). Any repository licensed to dispose of the SNF must meet requirements regarding the long-term performance of the repository. In evaluating the long-term performance of the repository, one of the events that may need to be considered is the SNF achieving a critical configuration. Of particular interest is the potential behavior of SNF in dual-purpose canisters (DPCs), which are currently being used to store the SNF but were not designed for permanent disposal. As part of a multiyear plan that is currently being developed for the DOE, a two-phase study has been initiated to examine the potential consequences, with respect to long-term repository performance, of criticality events that might occur during the postclosure period in a hypothetical repository containing DPCs. Phase I, a scoping phase, consists of generating an approach intended to be a starting point for the development of the modeling tools and techniques that may eventually be required either to exclude criticality from or include criticality in a performance assessment (PA) as appropriate. The Phase I approach will be used to guide the analyses and simulations done in Phase II to further the development of these modeling tools and techniques as well as the overall knowledge base. The purpose of this report is to document the approach created during Phase I. The study discussed herein focuses on the consequences of criticality in a DPC; it does not address the probability of occurrence of a criticality event. This approach examines two types of criticality events for SNF disposed of in a single type of DPC: a steady-state criticality and a transient criticality. The steady-state critical event is characterized by a relatively low constant power output over 10,000 years, while the transient critical event is characterized by a power spike that lasts on the order of seconds. Possible effects of the criticality are an increase in the radionuclide inventory; an increase in temperature; and a change in the chemistry inside the waste package, along with a change in radionuclide solubilities, fuel degradation rates, and steel corrosion rates. Additionally, for transient criticality the possibility of mechanical damage to the engineered and natural barriers also exists.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Formation of a Graphene-Like SiN Layer on the Surface Si(111)

00-The kinetics of the formation and thermal decomposition of a two-dimensional SiN-(8 × 8) nitride layer on a Si(111) surface is studied. The SiN-(8 × 8) structure is a metastable intermediate phase formed during the nitridation of silicon before the formation of a stable amorphous Si{sub 3}N{sub 4} phase. Studying the SiN-(8 × 8) structure by scanning tunneling microscopy shows its complex structure: it consists of an adsorption (8/3 × 8/3) phase, with the lateral period 10.2 Å, and a honeycomb structure with a ~6 Å side of a hexagon that is turned 30° with respect the adsorption phase. The band gap of the SiN-(8 × 8) phase is measured and found to be ~2.8 eV, which is smaller compared to the band gap of the β-Si{sub 3}N{sub 4} crystal phase 5.3 eV. The interplanar spacings in the (AlN{sub 3})/(SiN){sub 2} structure on the Si(111) surface are measured. The spacings are 3.3 and 2.86 Å in SiN and AlN, respectively. Such interplanar spacings are indicative of weak van der Waals interaction between the layers. A model of the SiN-(8 × 8) structure as a flat graphene-like layer is suggested. The model is consistent with the diffraction and microscopy data.

36 MATERIALS SCIENCE↗

TAILORING INORGANIC SORBENTS FOR SRS STRONTIUM AND ACTINIDE SEPARATIONS: MODIFIED MONOSODIUM TITANATE PHASE III FINAL REPORT

This document provides a final report of Phase III testing activities for the development of modified monosodium titanate (mMST), which exhibits improved strontium and actinide removal characteristics compared to the baseline MST material. The activities included characterization of the crystalline phases present at varying temperatures, solids settling characteristics, quantification of the peroxide content; evaluation of the post-synthesis gas release under different conditions; the extent of desorption of {sup 85}Sr, Np, and Pu under washing conditions; and the effects of age and radiation on the performance of the mMST. Key findings and conclusions include the following. The peroxide content of several mMST samples was determined using iodometric titration. The peroxide content was found to decrease with age or upon extended exposure to elevated temperature. A loss of peroxide was also measured after exposure of the material to an alkaline salt solution similar in composition to the simulated waste solution. To determine if the loss of peroxide with age affects the performance of the material, Sr and actinide removal tests were conducted with samples of varying age. The oldest sample (4 years and 8 months) did show lower Sr and Pu removal performance. When compared to the youngest sample tested (1 month), the oldest sample retained only 15% of the DF for Pu. Previous testing with this sample indicated no decrease in Pu removal performance up to an age of 30 months. No loss in Np removal performance was observed for any of the aged samples, and no uptake of uranium occurred at the typical sorbent loading of 0.2 g/L. Additional testing with a uranium only simulant and higher mMST loading (3.0 g/L) indicated a 10% increase of uranium uptake for a sample aged 3 years and 8 months when compared to the results of the same sample measured at an age of 1 year and 5 months. Performance testing with both baseline-MST and mMST that had been irradiated in a gamma source to a total dose of 3.95 x 10{sup 6} R, indicated little to no affect on the performance of the material to remove Sr and actinides. Previous testing established that mMST releases oxygen gas during the synthesis, and continues to off-gas during storage post synthesis. The post-synthesis gas release rate was measured under several conditions, including varying the pH of the wash water and at elevated temperature (49 C, typical of bounding summertime storage without air conditioning). Results indicated that a high pH (basic) wash reduced the initial gas release rate, but after 2 days the release rates from all different pH washed samples were not statistically different. The gas release rate at 49 C, a temperature at which the material may be exposed to during shipping and storage, was consistently about 2.5 times higher than the rate at room temperature. All gas release results indicated that vented containers would be necessary for shipping and storage of large quantities of material. Suspension of sorbate-loaded solids into diluted solutions representing intermediate and final stages of washing for 24-hours revealed no evidence of desorption of Sr, Pu or Np from the mMST solids. Based on the results of the Phase III testing as well as that from earlier studies (Phases I and II), SRNL researchers recommend adopting the use of the mMST material for the removal of strontium and actinides from the SRS HLW supernatant liquids in the Actinide Removal Process and Salt Waste Processing Facility. Given the decrease in Sr and Pu removal performance for the mMST having an age of 4 years and 8 months, we recommend that mMST be used within 30 months of production. Furthermore we recommend that DOE provide funding to conduct pilot-scale testing of the mixing and settling characteristics of the mMST and impact, if any, on the generation of hydrogen during processing in the Defense Waste Processing Facility (DWPF).

08 HYDROGEN↗

The phase accumulation and antenna near field of microscopic propagating spin wave devices

We studied phase accumulation by the highly non-reciprocal magnetostatic surface spin waves in thin Permalloy microstripes excited and received by microscopic coplanar antennae. We find that the experimentally measured characteristic length of the near field of the antenna is smaller than the total width of the coplanar. This is confirmed by our numerical simulations. Consequently, the distance over which the spin wave accumulates its phase while travelling between the input and output antennae coincides with the distance between the antennae symmetry axes with good accuracy.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Magnetism and phase transitions in LaCoO3

Neutron scattering and magnetometry measurements have been used to study phase transitions in LaCoO3 (LCO). For H 100 Oe, evidence for a ferromagnetic (FM) transition is observed at Tc 87 K. For 1 kOe H 60 kOe, no transition is apparent. For all H, Curie Weiss analysis shows predominantly antiferromagnetic (AFM) interactions for T > Tc, but the lack of long-range AFM order indicates magnetic frustration. We argue that the weak ferromagnetism in bulk LCO is induced by lattice strain, as is the case with thin films and nanoparticles. The lattice strain is present at the bulk surfaces and at the interfaces between the LCO and a trace cobalt oxide phase. The ferromagnetic ordering in the LCO bulk is strongly affected by the Co O Co angle ( ), in agreement with recent band calculations which predict that ferromagnetic long-range order can only take place above a critical value, C. Consistent with recent thin film estimations, we find C D 162:8. For > C, we observe power-law behavior in the structural parameters. decreases with T until the critical temperature, To 37 K; below To the rate of change becomes very small. For T < To, FM order appears to be confined to regions close to the surfaces, likely due to the lattice strain keeping the local Co O Co angle above C.

Belanger, David P↗

Comparison of Image Restoration Methods for Lunar Epithermal Neutron Emission Mapping

Orbital measurements of neutrons by the Lunar Exploring Neutron Detector (LEND) onboard the Lunar Reconnaissance Orbiter are being used to quantify the spatial distribution of near surface hydrogen (H). Inferred H concentration maps have low signal-to-noise (SN) and image restoration (IR) techniques are being studied to enhance results. A single-blind. two-phase study is described in which four teams of researchers independently developed image restoration techniques optimized for LEND data. Synthetic lunar epithermal neutron emission maps were derived from LEND simulations. These data were used as ground truth to determine the relative quantitative performance of the IR methods vs. a default denoising (smoothing) technique. We review and used factors influencing orbital remote sensing of neutrons emitted from the lunar surface to develop a database of synthetic "true" maps for performance evaluation. A prior independent training phase was implemented for each technique to assure methods were optimized before the blind trial. Method performance was determined using several regional root-mean-square error metrics specific to epithermal signals of interest. Results indicate unbiased IR methods realize only small signal gains in most of the tested metrics. This suggests other physically based modeling assumptions are required to produce appreciable signal gains in similar low SN IR applications.

McClanahan, T. P.↗

A compact apparatus for studies of element and phase-resolved ferromagnetic resonance

We present a compact sample holder equipped with electromagnets and high frequency transmission lines; the sample holder is intended for combined x-ray magnetic circular dichroism (XMCD) and ferromagnetic resonance measurements (FMR). Time-resolved measurements of resonant x-ray detected FMR during forced precession are enabled by use of a rf excitation that is phase-locked to the storage ring bunch clock. Several applications of the combined XMCD+FMR technique are presented, demonstrating the flexibility of the experimental design.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Orthostatic responses to dietary sodium restriction during heat acclimation

Several studies have shown that individuals consuming low-salt diets and working in the heat have an increased risk or incidence of heat injury, suggestive of inadequate cardiovascular adjustment. Furthermore, others have shown that prolonged work in hot climates can precipitate orthostatic hypotension and syncope. This study was designed to evaluate the effects of moderate-salt (MS) and low-salt (LS) diets on the circulatory responses and incidence of presyncopal symptoms to an orthostatic test (OT) during successive days of heat acclimation (HA). Seventeen unacclimatized male soldiers (mean +/- SE: age 20+/-1 yrs) participated in this two-phase study. The first phase consisted of a seven day dietary stabilization period during which all subjects consumed similar diets of about 4000 kcal/day containing 8g NaCl and lived in a dormitory setting (21 C, 30% RH). The second phase commenced on day eight and consisted of dietary NaCl restriction and 10 days HA (days 8-17). Volunteers were randomly assigned to either the MS diet (n=9) providing 8g NaCl/day or the LS diet (n=8) furnishing just 4g NaCl/day. The acquisition of HA was manifested in both groups by reductions in exercising rectal temperature and heart rate (HR); these characteristics were similar in the MS and LS diets. The OT was performed at 21 C on day seven of the stabilization phase and on days 9, 11, 13, 15, and 17 of the HA phase, before and after 8.5 hr of intermittent treadmill walking in a hot environment. Blood pressure (BP) and HR responses at 1,2, and 4 min and any presyncopal symptoms were recorded after assuming an upright position from recumbency. All subjects completed the OT before and after prolonged exercise in the heat without incidence of either hypotension or presyncopal symptoms irrespective of dietary-salt intake and day of HA. The results indicate that the prolonged work in the heat can be performed without orthostatic hypotension or syncope while consuming 4g NaCl/day with adequate fluid replacement. Furthermore, the circulatory responses to OT showed no improvement with successive days of HA irrespective of dietary-salt intake.

Szlyk, Patricia C.↗

Progress on the Development of the Nb 3 Sn 11T Dipole for the High Luminosity Upgrade of LHC

The high-luminosity large hadron collider (LHC) project at CERN entered into the production phase in October 2015 after the completion of the design study phase. In the meantime, the development of the 11 T dipole needed for the upgrade of the collimation system of the machine made significant progress with very good performance of the first two-in-one magnet model of 2-m length made at CERN. The 11 T dipole, which is more powerful than the current main dipoles of LHC, can be made shorter with an equivalent integrated field. This will allow creating space for the installation of additional collimators in specific locations of the dispersion suppressor regions. Following tests carried out during heavy ions runs of LHC in the end of 2015, and a more recent review of the project budget, the installation plan for the 11 T dipole was revised. Consequently, one 11 T dipole full assembly containing two 11 T dipoles of 5.5-m length will be installed on either side of interaction point 7. These two units shall be installed during the long shutdown 2 in years 2019-2020. After a brief reminder on the design features of the magnet, this paper describes the current status of the development activities, in particular the short model programme and the construction of the first full scale prototype at CERN. Finally, critical operations such as the reaction treatment and the coil impregnation are discussed, the quench performance tests results of the two-in-one model are reviewed and finally, the plan toward the production for the long shut down 2 is described.

43 PARTICLE ACCELERATORS↗

The influence of defects of the fatigue resistance of butt and girth welds in A106B steel

This three-phase study was directed at developing a fitness for service defect acceptance criteria for welds with defect indications. The study focussed on A106 Gr. B steel pipe. The first phase involved a literature search and critical review to develop the preliminary acceptance criteria to the extent permitted by the data. The second phase developed data for flat plate, wall segment, and vessel specimens containing artificial or natural planar or volumetric defects. The final phase developed acceptance criteria from the test data.

Leis, B. N.↗

Growth and electrical performance of Pb(Mg{sub 1/3}Nb{sub 2/3})O{sub 3}-PbTiO{sub 3}-Pb(Fe{sub 1/2}Nb{sub 1/2})O{sub 3} single crystals

For the first time, we have grown ferroelectric single crystals Pb(Mg{sub 1/3}Nb{sub 2/3})O{sub 3}-PbTiO{sub 3}-Pb(Fe{sub 1/2}Nb{sub 1/2})O{sub 3} (PMN-PT-PFN) from the melt by the simple slow cooling process. The chemical composition of the single crystals PMN-PT-PFN (0.59/0.31/0.10) is near the morphotropic phase boundary (MPB). X-ray diffraction (XRD) was used to study phase structure of the as-grown crystals, energy dispersive X-ray spectrometer (EDS) and electron probe micro-analyzer (EPMA) were employed to confirm the chemical composition and element distribution of the as-grown crystals, respectively. The ferroelectric, dielectric and piezoelectric properties of the as-grown PMN-PT-PFN (0.59/0.31/0.10) single crystal oriented along the (0 0 1) axis were measured, which showed that the remnant polarization (P{sub r}), coercive electric fields (E{sub c}), the Curie temperature (T{sub c}) and the piezoelectric coefficient (d{sub 33}) were 50.2 {mu}C/cm{sup 2}, 13.9 kV/cm, 158 deg. C and about 1800 pC/N, respectively. All the results indicated that the PMN-PT-PFN (0.59/0.31/0.10) single crystals are promising for applying to field of high frequency.

36 MATERIALS SCIENCE↗

Calibrating cryogenic temperature of TEM specimens using EELS

Cryogenic Scanning/Transmission Electron Microscopy has been established as a leading method to image sensitive biological samples and is now becoming a powerful tool to understand materials' behavior at low temperatures. However, achieving precise local temperature calibration at low temperatures remains a challenge, which is especially crucial for studying phase transitions and emergent physical properties in quantum materials. In this study, we employ electron energy loss spectroscopy (EELS) to measure local cryogenic specimen temperatures. Here we use the temperature-dependent characteristics of aluminum's bulk plasmon peak in EEL spectra, which shifts due to changes in electron density caused by thermal expansion and contraction. We successfully demonstrate the versatility of this method by calibrating different liquid nitrogen cooling holders in various microscopes, regardless of whether a monochromated or non-monochromated electron beam is used. Temperature discrepancies between the actual temperature and the setpoint temperatures are identified across a range from room temperature to 100 K. This work demonstrates the importance of temperature calibrations at intermediate temperatures and presents a straightforward, robust method for calibrating local temperatures of cryogenically-cooled specimens in electron microscopes.

36 MATERIALS SCIENCE↗

TDRSS data handling and management system study. Ground station systems for data handling and relay satellite control

Results of a two-phase study of the (Data Handling and Management System DHMS) are presented. An original baseline DHMS is described. Its estimated costs are presented in detail. The DHMS automates the Tracking and Data Relay Satellite System (TDRSS) ground station's functions and handles both the forward and return link user and relay satellite data passing through the station. Direction of the DHMS is effected via a TDRSS Operations Control Central (OCC) that is remotely located. A composite ground station system, a modified DHMS (MDHMS), was conceptually developed. The MDHMS performs both the DHMS and OCC functions. Configurations and costs are presented for systems using minicomputers and midicomputers. It is concluded that a MDHMS should be configured with a combination of the two computer types. The midicomputers provide the system's organizational direction and computational power, and the minicomputers (or interface processors) perform repetitive data handling functions that relieve the midicomputers of these burdensome tasks.

Source record↗

Benchmark On Sensitivity Calculation (Phase III)

The sensitivities of the keff eigenvalue to neutron cross sections have become commonly used in similarity studies and as part of the validation algorithm for criticality safety assessments. To test calculations of the sensitivity coefficients, a benchmark study (Phase III) has been established by the OECD-NEA/WPNCS/EG UACSA (Expert Group on Uncertainty Analysis for Criticality Safety Assessment). This paper presents some sensitivity results generated by the benchmark participants using various computational tools based upon different computational methods: SCALE/TSUNAMI-3D and -1D, MONK, APOLLO2-MORET 5, DRAGON-SUSD3D and MMKKENO. The study demonstrates the performance of the tools. It also illustrates how model simplifications impact the sensitivity results and demonstrates the importance of 'implicit' (self-shielding) sensitivities. This work has been a useful step towards verification of the existing and developed sensitivity analysis methods.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗