Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Nonlinear models”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

PMSM Parameter Estimation using a Linear Unknown Input Interval Observer

In this paper, the problem of permanent magnet synchronous motor (PMSM) speed and unknown load torque estimation is addressed. For this purpose, a interval unknown input observer (UIO) for linear time-invariant (LTI) systems is used. First, the PMSM model is linearized in order to make it in a suitable form for the linear interval UIO. Then, the interval UIO is applied to allow the joint estimation of the motor speed and the unknown load torque disturbance. The main advantages of this approach is that it not only allows the joint state and unknown input estimation, but also to take the different uncertainty sources into account. Indeed, taking model and measurement uncertainty into account is crucial. Assuming that the measurement noise and disturbances are bounded, lower and upper bounds are first computed for the unmeasured state (motor speed) and then for the unknown input (load torque). The proposed approach and its limitations are demonstrated with the nonlinear PMSM model derived from its equivalent electrical circuit.

Elinirina I Robinson↗
NASA NTRS1975

Design and simulation of a descent controller for strategic four-dimensional aircraft navigation

A time-controlled navigation system applicable to the descent phase of flight for airline transport aircraft was developed and simulated. The design incorporates the linear discrete-time sampled-data version of the linearized continuous-time system describing the aircraft's aerodynamics. Using optimal linear quadratic control techniques, an optimal deterministic control regulator which is implementable on an airborne computer is designed. The navigation controller assists the pilot in complying with assigned times of arrival along a four-dimensional flight path in the presence of wind disturbances. The strategic air traffic control concept is also described, followed by the design of a strategic control descent path. A strategy for determining possible times of arrival at specified waypoints along the descent path and for generating the corresponding route-time profiles that are within the performance capabilities of the aircraft is presented. Using a mathematical model of the Boeing 707-320B aircraft along with a Boeing 707 cockpit simulator interfaced with an Adage AGT-30 digital computer, a real-time simulation of the complete aircraft aerodynamics was achieved. The strategic four-dimensional navigation controller for longitudinal dynamics was tested on the nonlinear aircraft model in the presence of 15, 30, and 45 knot head-winds. The results indicate that the controller preserved the desired accuracy and precision of a time-controlled aircraft navigation system.

Lax, F. M.↗
NASA NTRS1984

Pattern selection in solidification

Directional solidification of alloys produces a wide variety of cellular or lamellar structures which, depending upon growth conditions, may be reproducibly regular or may behave chaotically. It is not well understood how these patterns are selected and controlled or even whether there ever exist sharp selection mechanisms. A related phenomenon is the spatial propagation of a pattern into a system which has been caused to become unstable against pattern-forming deformations. This phenomenon has some features in common with the propagation of sidebranching modes in dendritic solidification. In a class of one-dimensional models, the nonlinear system can be shown to select the propagating mode in which the leading edge of the pattern is just marginally stable. This stability principle, when applicable, predicts both the speed of propagation and the geometrical characteristics of the pattern which forms behind the moving front. A boundary-layer model for fully two or three dimensional solidification problems appears to exhibit similar mathematical behavior.

Langer, J. S.↗
NASA NTRS1991

Diurnal forcing of planetary atmospheres

The utility of the Mars Planetary Boundary Layer Model (MPBL) for calculations in support of the Mars 94 balloon mission was substantially enhanced by the introduction of a balloon equation of motion into the model. Both vertical and horizontal excursions of the balloon are calculated along with its volume, temperature, and pressure. The simulations reproduce the expected 5-min vertical oscillations of a constant density balloon at altitude on Mars. The results of these calculations are presented for the nominal target location of the balloon. A nonlinear balanced model was developed for the Martian atmosphere. It was used to initialize a primitive equation model for the simulations of the Earth's atmosphere at the time of the El Chichon eruption in 1982. It is also used as an assimilation model to update the temperature and wind fields at frequent intervals.

Houben, Howard C.↗
NASA NTRS1991

Thermal barrier coating life prediction model development, phase 2

The objective of this program was to generate a life prediction model for electron-beam-physical vapor deposited (EB-PVD) zirconia thermal barrier coating (TBC) on gas turbine engine components. Specific activities involved in development of the EB-PVD life prediction model included measurement of EB-PVD ceramic physical and mechanical properties and adherence strength, measurement of the thermally grown oxide (TGO) growth kinetics, generation of quantitative cyclic thermal spallation life data, and development of a spallation life prediction model. Life data useful for model development was obtained by exposing instrumented, EB-PVD ceramic coated cylindrical specimens in a jet fueled burner rig. Monotonic compression and tensile mechanical tests and physical property tests were conducted to obtain the EB-PVD ceramic behavior required for burner rig specimen analysis. As part of that effort, a nonlinear constitutive model was developed for the EB-PVD ceramic. Spallation failure of the EB-PVD TBC system consistently occurred at the TGO-metal interface. Calculated out-of-plane stresses were a small fraction of that required to statically fail the TGO. Thus, EB-PVD spallation was attributed to the interfacial cracking caused by in-plane TGO strains. Since TGO mechanical properties were not measured in this program, calculation of the burner rig specimen TGO in-plane strains was performed by using alumina properties. A life model based on maximum in-plane TGO tensile mechanical strain and TGO thickness correlated the burner rig specimen EB-PVD ceramic spallation lives within a factor of about plus or minus 2X.

Meier, Susan Manning↗
NASA NTRS1992

The nonlinear forced response characteristics of contained fluids in microgravity

An experimental study of the change in the lateral slosh behavior of contained fluids between earth and space is presented. The experimental apparatus used to determine the slosh characteristics is described and a nonlinear analytic model of a coupled fluid/spacecraft system is outlined. The forced response characteristics of silicon oil and distilled water in cylinder tanks with either a flat or spherical bottom are reported and discussed. A comparison of the measured earth and space results identifies and highlights the effects of gravity on the linear and nonlinear slosh behavior of these fluids.

Vanschoor, M. C.↗
NASA NTRS2003

Analytical Modeling of the High Strain Rate Deformation of Polymer Matrix Composites

The results presented here are part of an ongoing research program to develop strain rate dependent deformation and failure models for the analysis of polymer matrix composites subject to high strain rate impact loads. State variable constitutive equations originally developed for metals have been modified in order to model the nonlinear, strain rate dependent deformation of polymeric matrix materials. To account for the effects of hydrostatic stresses, which are significant in polymers, the classical 5 plasticity theory definitions of effective stress and effective plastic strain are modified by applying variations of the Drucker-Prager yield criterion. To verify the revised formulation, the shear and tensile deformation of a representative toughened epoxy is analyzed across a wide range of strain rates (from quasi-static to high strain rates) and the results are compared to experimentally obtained values. For the analyzed polymers, both the tensile and shear stress-strain curves computed using the analytical model correlate well with values obtained through experimental tests. The polymer constitutive equations are implemented within a strength of materials based micromechanics method to predict the nonlinear, strain rate dependent deformation of polymer matrix composites. In the micromechanics, the unit cell is divided up into a number of independently analyzed slices, and laminate theory is then applied to obtain the effective deformation of the unit cell. The composite mechanics are verified by analyzing the deformation of a representative polymer matrix composite (composed using the representative polymer analyzed for the correlation of the polymer constitutive equations) for several fiber orientation angles across a variety of strain rates. The computed values compare favorably to experimentally obtained results.

Goldberg, Robert K.↗
NASA NTRS1982

Simplified aeroelastic modeling of horizontal axis wind turbines

Certain aspects of the aeroelastic modeling and behavior of the horizontal axis wind turbine (HAWT) are examined. Two simple three degree of freedom models are described in this report, and tools are developed which allow other simple models to be derived. The first simple model developed is an equivalent hinge model to study the flap-lag-torsion aeroelastic stability of an isolated rotor blade. The model includes nonlinear effects, preconing, and noncoincident elastic axis, center of gravity, and aerodynamic center. A stability study is presented which examines the influence of key parameters on aeroelastic stability. Next, two general tools are developed to study the aeroelastic stability and response of a teetering rotor coupled to a flexible tower. The first of these tools is an aeroelastic model of a two-bladed rotor on a general flexible support. The second general tool is a harmonic balance solution method for the resulting second order system with periodic coefficients. The second simple model developed is a rotor-tower model which serves to demonstrate the general tools. This model includes nacelle yawing, nacelle pitching, and rotor teetering. Transient response time histories are calculated and compared to a similar model in the literature. Agreement between the two is very good, especially considering how few harmonics are used. Finally, a stability study is presented which examines the effects of support stiffness and damping, inflow angle, and preconing.

Wendell, J. H.↗
NASA NTRS2002

On the validity of the double integrator approximation in deep space formation flying

Free-flying models are commonly used f o r path planning and open loop control design (i. e., guidance design) and translational feedback control design (i. e., control design) for deep space precision formation flying. The free flying model, essentially a double integrator, results from discarding small terms in the relative spacecraft equations of motion. While the magnitude of these discarded terms may be small, one must show that their dynamic effects are small as compared to the precision performance requirements. We do so by deriving a theoretical method for bounding the difference between the solution of a nonlinear truth model of the relative translational spacecraft dynamics and a Simplified linear time-invariant model. Presently, the method incorporates feedforward and static output feedback control. The method is applied to a Terrestrial Planet Finder- based example. Using only feedforward control (guidance) the free-flying model and a Hill- Clohessy- Wiltshire Equations-based model are shown to be accurate to 1 c m for up to 4 and 30 hours, respectively. Also shown is that the simplest free-flying model may not be sufficient for low-gain feedback control design-closed-loop tracking errors can be as large as 8 meters.

formation flying free flying model double integrat↗
NASA NTRS1985

Impact of airfoil profile on the supersonic aerodynamics of delta wings

A nonlinear flow model was employed to predict the flowfield, pressure and force data for delta wings at supersonic speeds. The goal of the study was to investigate the influence the airfoil profiles has on the wing aerodynamics. The analysis covers wing aspect ratios from 0.5-3.0 with leading edge sweep of 0.5-4.0 on diamond, circular arc and NACA modified 4-digit airfoils. Nonlinear aerodynamics are approximated with nonlinear zero-lift wave drag curves, yielding results significantly different from those obtained from linear calculations. The analytical technique, useful in preliminary design studies, indicates in all cases that 90 percent of wave drag is generated at the wing apex and trailing edge.

Wood, R. M.↗
NASA NTRS1974

Computational study of nonlinear plasma waves: 1: Simulation model and monochromatic wave propagation

An economical low noise plasma simulation model is applied to a series of problems associated with electrostatic wave propagation in a one-dimensional, collisionless, Maxwellian plasma, in the absence of magnetic field. The model is described and tested, first in the absence of an applied signal, and then with a small amplitude perturbation, to establish the low noise features and to verify the theoretical linear dispersion relation at wave energy levels as low as 0.000,001 of the plasma thermal energy. The method is then used to study propagation of an essentially monochromatic plane wave. Results on amplitude oscillation and nonlinear frequency shift are compared with available theories. The additional phenomena of sideband instability and satellite growth, stimulated by large amplitude wave propagation and the resulting particle trapping, are described.

Matda, Y.↗
NASA NTRS2022

Space Weather Modeling and Prediction for Intermediate Time-scales

Much of solar activity within a sunspot cycle occurs as bursts, or 'seasons' of strong activity over several months, separated by periods of much less activity. The most important space weather effects occur during these bursts. Previous modeling and forecasting efforts have focused on time-scales of hours-to-days and decades-to-centuries. The recent discovery of Rossby waves in the Sun, together with recently developed global models of solar MHD Rossby waves and their interactions with differential rotation and spot-producing magnetic fields, reveal the opportunity to simulate and predict the occurrence, strength and location of enhanced activity bursts a few weeks up to several months in advance. We now have a golden opportunity to fill in this gap in time-scales of forecasting space weather. This requires a) continuous observations of solar Rossby waves by various techniques; b) development of coupled nonlinear MHD models that simulate both global Rossby waves and the much smaller spatial scale emergence of new active regions; c) application of advanced data assimilation techniques to couple surface observations to update the model-system to integrate forward in time for creating forecasts months ahead. Then it will be possible to build operational prediction models to meet the needs of customers and stakeholders, including support of future NASA missions, regarding what kind and level of space weather to expect a few weeks to several months ahead.

SMD↗
NASA NTRS2016

Development of Semi-Empirical Damping Equation for Baffled Tank with Oblate Spheroidal Dome

Propellant slosh is a potential source of disturbance that can significantly impact the stability of space vehicles. The slosh dynamics are typically represented by a mechanical model of a spring-mass-damper. This mechanical model is then included in the equation of motion of the entire vehicle for Guidance, Navigation and Control analysis. The typical parameters required by the mechanical model include natural frequency of the slosh, slosh mass, slosh mass center location, and the critical damping ratio. A fundamental study has been undertaken at NASA MSFC to understand the fluid damping physics from a ring baffle in the barrel section of a propellant tank. An asymptotic damping equation and CFD blended equation have been derived by NASA MSFC team to complement the popularly used Miles equation at different flow regimes. The new development has found success in providing a nonlinear damping model for the Space Launch System. The purpose of this study is to further extend the semi-empirical damping equations into the oblate spheroidal dome section of the propellant tanks. First, previous experimental data from the spherical baffled tank are collected and analyzed. Several methods of taking the dome curvature effect, including a generalized Miles equation, area projection method, and equalized fill height method, are assessed. CFD simulation is used to shed light on the interaction of vorticity around the baffle with the locally curved wall and liquid-gas interface. The final damping equation will be validated by a recent subscale test with an oblate spheroidal dome conducted at NASA MSFC.

Yang, H. Q.↗
NASA NTRS1984

A global low order spectral model designed for climate sensitivity studies

A two level, global, spectral model using pressure as a vertical coordinate is developed. The system of equations describing the model is nonlinear and quasi-geostrophic. A moisture budget is calculated in the lower layer only with moist convective adjustment between the two layers. The mechanical forcing of topography is introduced as a lower boundary vertical velocity. Solar forcing is specified assuming a daily mean zenith angle. On land and sea ice surfaces a steady state thermal energy equation is solved to calculate the surface temperature. Over the oceans the sea surface temperatures are prescribed from the climatological average of January. The model is integrated to simulate the January climate.

Hanna, A. F.↗
NASA NTRS1987

An adaptive control scheme for a flexible manipulator

The problem of controlling a single link flexible manipulator is considered. A self-tuning adaptive control scheme is proposed which consists of a least squares on-line parameter identification of an equivalent linear model followed by a tuning of the gains of a pole placement controller using the parameter estimates. Since the initial parameter values for this model are assumed unknown, the use of arbitrarily chosen initial parameter estimates in the adaptive controller would result in undesirable transient effects. Hence, the initial stage control is carried out with a PID controller. Once the identified parameters have converged, control is transferred to the adaptive controller. Naturally, the relevant issues in this scheme are tests for parameter convergence and minimization of overshoots during control switch-over. To demonstrate the effectiveness of the proposed scheme, simulation results are presented with an analytical nonlinear dynamic model of a single link flexible manipulator.

Yang, T. C.↗
NASA NTRS2020

Nonlinear Slosh Damping Testing and Analysis for Launch Vehicle Propellant Tanks

Propellant tank slosh damping models for launch vehicle ascent analysis typically employ linear models for bare-wall damping, or assume a single, low-amplitude wave height for baffled configurations. A higher fidelity damping model would incorporate nonlinear effects to increase damping as slosh wave amplitude increases. This paper provides an overview of a technical assessment performed by the NASA Engineering and Safety Center (NESC) to evaluate lateral slosh damping as a function of lateral force (or wave) amplitude for multiple tank configurations. The increased fidelity of nonlinear slosh damping models, if leveraged, has the potential to reduce over-conservatism associated with the use of linear slosh damping models. This can provide design flexibility to enhance launch vehicle flight control performance, reduce baffle design requirements and/or increase robustness in targeted areas such as control-structure interaction during ascent.

Tannen S VanZwieten↗
NASA NTRS1997

Evolution of Nonlinear Internal Waves in China Seas

Synthetic Aperture Radar (SAR) images from ERS-I have been used to study the characteristics of internal waves of Taiwan in the East China Sea, and east of Hainan Island in the South China Sea. Rank-ordered packets of internal solitons propagating shoreward from the edge of the continental shelf were observed in the SAR images. Based on the assumption of a semidiurnal tidal origin, the wave speed can be estimated and is consistent with the internal wave theory. By using the SAR images and hydrographic data, internal waves of elevation have been identified in shallow water due to a thicker mixed layer as compared with the bottom layer on the continental shelf. The generation mechanism includes the influences of the tide and the Kuroshio intrusion across the continental shelf for the formations of elevation internal waves. The effects of water depth on the evolution of solitons and wave packets are modeled by nonlinear Kortweg-deVries (KdV) type equation and linked to satellite image observations. The numerical calculations of internal wave evolution on the continental shelf have been performed and compared with the SAR observations. For a case of depression waves in deep water, the solitons first disintegrate into dispersive wave trains and then evolve to a packet of elevation waves in the shallow water area after they pass through a turning point of approximately equal layer depths has been observed in the SAR image and simulated by numerical model.

Liu, Antony K.↗