Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Modal Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

Advanced superposition methods for high speed turbopump vibration analysis

The small, high pressure Mark 48 liquid hydrogen turbopump was analyzed and dynamically tested to determine the cause of high speed vibration at an operating speed of 92,400 rpm. This approaches the design point operating speed of 95,000 rpm. The initial dynamic analysis in the design stage and subsequent further analysis of the rotor only dynamics failed to predict the vibration characteristics found during testing. An advanced procedure for dynamics analysis was used in this investigation. The procedure involves developing accurate dynamic models of the rotor assembly and casing assembly by finite element analysis. The dynamically instrumented assemblies are independently rap tested to verify the analytical models. The verified models are then combined by modal superposition techniques to develop a completed turbopump model where dynamic characteristics are determined. The results of the dynamic testing and analysis obtained are presented and methods of moving the high speed vibration characteristics to speeds above the operating range are recommended. Recommendations for use of these advanced dynamic analysis procedures during initial design phases are given.

Nielson, C. E.↗

Finite Element Model Tuning using Analytical Sensitivity Values

This paper presents an efficient approach for tuning finite element models to match the measured ground vibrationtest and proof test data. Frequencies, mode shapes, total weight, location of the center of gravity, and staticdeformation computed from the finite element model are matched to the measured data. The model tuningprocedure used in this work is based on solving an optimization problem in which the errors for the consideredmetrics, between the finite element prediction and the measured data, are minimized. Analytical sensitivity values ofperformance indices are computed using the NASTRAN-generated sensitivity values together with the in-housecomputer programs, which allow for faster computational time and the use of gradient-based optimizers. The methodis applied to the Aerostructures Test Wing 4 model. The study shows that the military standard and the NASAstandard for comparing analytical and experimental modal data are all satisfied. The final finite element modelcorrelates well with the test data. The flutter speed decreases by 8.91% after model tuning compared with the original Aerostructures Test Wing 4 design.

Chan-gi Pak↗

Shake test of rotor test apparatus with balance dampers in the 40 by 80 foot wind tunnel

A shake test was conducted to determine the dynamic characteristics of a rotor test apparatus on two strut systems with balance dampers in the Ames 40- by 80-ft wind tunnel. The rotor-off hub transfer function (acceleration per unit force as a function of frequency) was measured in the longitudinal and lateral directions, using a combination of broadband and discrete frequency excitation techniques. The dynamic data are summarized for the configurations tested, giving the following properties for each mode identified: the natural frequency, the hub response at resonance, the fixed system damping, the damping ratio, and the modal mass. The complete transfer functions are presented, and the detailed test results are included as an appendix.

Johnson, W.↗

Waveform Analysis of AE in Composites

Advanced, waveform based acoustic emission (AE) techniques have been developed to evaluate damage mechanisms in the testing of composite materials. This approach, more recently referred to as Modal AE, provides an enhanced capability to discriminate and eliminate noise signals from those generated by damage mechanisms. Much more precise source location can also be obtained in comparison to conventional, threshold crossing arrival time determination techniques. Two successful examples of the application of Modal AE are presented in this work. In the first, the initiation of transverse matrix cracking in cross-ply, tensile coupons was monitored. In these tests, it was documented that the same source mechanism, matrix cracking, can produce widely different AE signal amplitudes dependent on laminate stacking sequence and thickness. These results, taken together with well known propagation effects of attenuation and dispersion of AE signals in composite laminates, cast further doubt on the validity of simple amplitude or amplitude distribution analysis for AE source determination. For the second example, delamination propagation in composite ring specimens was monitored. Pressurization of these composite rings is used to simulate the stresses in a composite rocket motor case. AE signals from delamination propagation were characterized by large amplitude flexural plate mode components which have long signal durations because of the large dispersion of this mode.

Prosser, William H.↗

Advanced Characterisation of Aerosol Size Properties from Measurements of Spectral Optical Depth Using the GRASP Algorithm

This study evaluates the potential of using aerosol optical depth (τ (sub a)) measurements to characterise the microphysical and optical properties of atmospheric aerosols. With this aim, we used the recently developed GRASP (Generalized Retrieval of Aerosol and Surface Properties) code for numerical testing of six different aerosol models with different aerosol loads. The direct numerical simulations (self-consistency tests) indicate that the GRASP-AOD retrieval provides modal aerosol optical depths (fine and coarse) to within 0.01 of the input values. The retrieval of the fine-mode radius, width and volume concentration are stable and precise if the real part of the refractive index is known. The coarse-mode properties are less accurate, but they are significantly improved when additional a priori information is available. The tests with random simulated errors show that the uncertainty in the bimodal log-normal size distribution parameters increases as the aerosol load decreases. Similarly, the reduction in the spectral range diminishes the stability of the retrieved parameters. In addition to these numerical studies, we used optical depth observations at eight AERONET locations to validate our results with the standard AERONET inversion products. We found that bimodal log-normal size distributions serve as useful input assumptions, especially when the measurements have inadequate spectral coverage and/or limited accuracy, such as moon photometry. Comparisons of the mode median radii between GRASP-AOD and AERONET indicate average differences of 0.013µm for the fine mode and typical values of 0.2–0.3µm for the coarse mode. The dominant mode (i.e. fine or coarse) indicates a 10 % difference in mode radii between the GRASP-AOD and AERONET inversions, and the average of the difference in volume concentration is around 17 % for both modes. The retrieved values of the fine-mode τ(sub a)(500) using GRASP-AOD are generally between those values obtained by the standard AERONET inversion and the values obtained by the AERONET spectral deconvolution algorithm (SDA), with differences typically lower than 0.02 between GRASP-AOD and both algorithms. Finally, we present some examples of application of GRASP-AOD inversion using moon photometry and the airborne PLASMA sun photometer during the ChArMEx summer 2013 campaign in the western Mediterranean.

Torres, Benjamin↗

High-Temperature Modal Survey of a Hot-Structure Control Surface

NASA Dryden is directing a program to test a Carbon-Silicon Carbide (C/SiC) Ruddervator Subcomponent Test Article (RSTA). The RSTA is a truncated version of the full-scale X-37 hot-structure control surface incorporating all major features including the metallic spindle and five major C/SiC quasi isotropic lay-up components secured with C/SiC fasteners. As part of NASA's Aeronautics Research Mission Directorate Hypersonics program, the RSTA will undergo thermal-structural testing to develop an extensive database for future structural design and analysis methodology validation. Ground Vibration Tests (GVTs) are routinely conducted for model validation in supporting flutter analysis for subsonic and supersonic vehicles; however, for hypersonic vehicle applications, GVT techniques are not well-established. New fabrication technologies, high-temperature materials systems, and sensors offer new opportunities to develop techniques for performing GVTs at elevated temperatures. The RSTA is comprised of materials whose stiffness both increases and decreases with increasing temperature. The impact of this type of material system interaction must be understood as it will ultimately affect hypersonic flutter analysis. The test objectives are to perform room-temperature GVTs, develop the capability to conduct high-temperature GVTs and to compare and generate an understanding of the modal characteristics which capture RSTA's material interaction when subjected to temperature varying conditions.

Spivey, Natalie D.↗

Coherent population trapping in Raman-pulse atom interferometry

Raman pulse atom interferometry is an important modality for precision measurements of inertial forces and tests of fundamental physics. Typical Raman atom optics use two coherent laser fields applied at gigahertz-scale detunings from optical resonance, so that spontaneous emission produces a minor or negligible source of decoherence. An additional consequence of spontaneous emission is coherent population trapping (CPT). We show that CPT produces coherences and population differences which induce systematic effects in Raman pulse atom interferometers. We do not believe that CPT has been previously identified as an error mechanism in Raman pulse atom interferometry. We present an experimental characterization of CPT coherences and population differences induced in laser-cooled cesium atoms by application of Raman pulses at detunings near 1 GHz, commensurate with detunings used in several precision measurement experiments. We are not aware of previous demonstrations of CPT-induced population difference. We argue that CPT effects could induce phase shifts of several milliradians in magnitude for typical experimental parameters and stipulate that these errors can be suppressed by propagation direction reversal in Raman interferometer-based precision measurements.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Scaling a discrete structural model to match measured modal frequencies

The structure modification problem, where the computer model of a structure is to be upgraded on the basis of experimental measurements of normal mode frequencies, is approached by the modal energy concept. The modes for correlation with test data are selected on the basis of relative strain energy participation. The resulting procedure can be viewed as an extension of White's (1972) method. Its advantage lies in that both the number and choice of structural parameters to be varied in the modification are arbitrary.

Taylor, J. E.↗

Sound radiation from single and annular stream nozzles, with modal decomposition of in-duct acoustic power

An experimental program was carried out to study the acoustic characteristics of single and annular stream duct-nozzle systems at various flow conditions by using a refined acoustic impulse technique. In this technique, signal synthesis and signal averaging processes are incorporated to generate a desired impulsive signal from acoustic driver(s) and to eliminate background noise (flow noise) from in-duct and far field signals, respectively. The contribution of higher order modes to incident reflected and transmitted acoustic powers is accounted for by using a modal decomposition process. The annular stream terminations were tested statically at various annular stream flow velocities with no inner stream flow. The results derived from the experiments include in-duct acoustic powers, termination reflection coefficients, transmission coefficients, far field power, and acoustic dissipation.

Salikuddin, M.↗

System identification using modal residues and roots

This presentation will address an approach for using modal residues and roots, typically derived from vibration testing, to solve for the lumped parameters of a finite element model. The uniqueness of the approach is that the mass, stiffness, or damping matrices of a structure do not need to be known or estimated a-priori. Instead just the connectivity of the structure needs to be estimated. In addition, the presentation will demonstrate how models with orders larger than the number of modes obtained by the test program can be solved. The presentation will start by covering the basis of the approach, then illustrate a trivial application of how it works, and finally illustrate its use on a cantilevered beam using only a fraction of the mode to solve the mass, stiffness, and damping matrices.

Wendler, Bruce H.↗

Spectral Measurements of Meteorite Powders: Implications for 433 Eros

One of the goals of the NEAR-Shoemaker mission to 433 Eros was to determine if it has a meteoritic analog. The primary means of making such a link are the X-ray/gamma-ray spectrometers, which measure elemental compositions of the surface, and the multi-spectral imager (MSI) and near-infrared spectrometer (NIS), which measure spectral reflectance. For determining meteoritic analogs using the X-ray/gamma-ray spectrometer data, the primary data used for comparison is the set of bulk chemical analyses of meteorites done by Jarosewich. These bulk chemical analyses were done on samples now found in the Smithsonian's Analyzed Meteorite Powder collection (USNM 7073). For determining meteoritic analogs using MSI/NIS spectral data, the primary data used for comparison is the set of meteoritic spectra compiled by Gaffey. To expand the set of meteoritic spectra available to the scientific community, we have initiated a spectral study of over 70 samples (primarily ordinary chondrites) found in the Smithsonian's Analyzed Meteorite Powder collection and an electron microprobe study of their corresponding thin sections. This set of spectral and compositional data should allow for better constraints on the distribution of meteorites in plots of band area ratios versus Band I centers and the usefulness of equations for deriving mineralogic compositions from band parameters. These spectral data can also be combined with previous spectral studies of other meteorite types such as the primitive achondrites, eucrites, and angrites to determine how useful the derived band parameters are for differentiating between different meteorite classes. These spectral data can also be used for testing the Modified Gaussian Model (MGM) for determining modal abundances and mafic mineral chemistries from reflectance spectra.

Burbine, T. H.↗

An Eigensystem Realization Algorithm (ERA) for modal parameter identification and model reduction

A method, called the Eigensystem Realization Algorithm (ERA), is developed for modal parameter identification and model reduction of dynamic systems from test data. A new approach is introduced in conjunction with the singular value decomposition technique to derive the basic formulation of minimum order realization which is an extended version of the Ho-Kalman algorithm. The basic formulation is then transformed into modal space for modal parameter identification. Two accuracy indicators are developed to quantitatively identify the system modes and noise modes. For illustration of the algorithm, examples are shown using simulation data and experimental data for a rectangular grid structure.

Juang, J. N.↗

Studies of modal identification performance using hybrid data

Modal identification accuracy can be affected significantly in practice by high modal density and nonlinearities. It may be difficult to determine the true number of modes, and many of the identified mode shapes may be questionable. Results can vary considerably using different analysis techniques. This paper introduces a new method for studying modal identification performance under such circumstances. A difficult set of test data from an erectable truss structure was modified numerically by adding two artificial modes with known parameters. These 'hybrid data' were then analyzed with the Polyreference technique and the Eigensystem Realization Algorithm (ERA). Identification performance is studied by comparing the identified modal parameters for the artificial modes with their known values.

Pappa, Richard S.↗

An eigensystem realization algorithm for modal parameter identification and model reduction

A method called the eigensystem realization algorithm is developed for modal parameter identification and model reduction of dynamic systems from test data. A new approach is introduced in conjunction with the singular-value decomposition technique to derive the basic formulation of minimum order realization which is an extended version of the Ho-Kalman algorithm. The basic formulation is then transformed into modal space for modal parameter identification. Two accuracy indicators are developed to quantitatively identify the system and noise modes. For illustration of the algorithm, an example is shown using experimental data from the Galileo spacecraft.

Juang, J.-N.↗

Simulating flight boundary conditions for orbiter payload modal survey

An approach to simulate the characteristics of the payload/orbiter interfaces for the payload modal survey was developed. The flexure designed for this approach is required to provide adequate stiffness separation in the free and constrained interface degrees of freedom to closely resemble the flight boundary condition. Payloads will behave linearly and demonstrate similar modal effective mass distribution and load path as the flight if the flexure fixture is used for the payload modal survey. The potential non-linearities caused by the trunnion slippage during the conventional fixed base modal survey may be eliminated. Consequently, the effort to correlate the test and analysis models can be significantly reduced. An example is given to illustrate the selection and the sensitivity of the flexure stiffness. The advantages of using flexure fixtures for the modal survey and for the analytical model verification are also demonstrated.

Chung, Y. T.↗

Quiet Spike Build-Up Ground Vibration Testing Approach

NASA's Dryden Flight Research Center uses a modified F-15B (836) aircraft as a testbed for a variety of flight research:experiments mounted underneath the aircraft fuselage. The F-15B was selected to fly Gulfstream Aerospace Corporation's (GAC)QuietSpike(TM)(QS) project; however, this experiment is very unique and unlike any of the previous testbed experiments flown on the F-15B. It involves the addition of a relatively long quiet spike boom attached to the radar bulkhead of the aircraft. This QS experiment is a stepping stone to airframe structural morphing technologies designed to mitigate sonic born strength of business jets over land. The QS boom is a concept in Which an aircraft's front-end would be extended prior to supersonic acceleration. This morphing would effectively lengthen the aircraft, reducing peak sonic boom amplitude, but is also expected to partition the otherwise strong bow shock into a series of reduced-strength, non-coalescing shocklets. Prior to flying the Quietspike(TM) experiment on the F-15B aircraft several ground vibration tests (GVT) were required in order to understand the QS modal characteristics and coupling effects with the F-15B. However, due to the project's late hardware delivery of the QS and the intense schedule, a "traditional" GVT of the mated F-1513 Quietspike(tm) ready-for-flight configuration would not have left sufficient time available for the finite element model update and flutter analyses before flight testing. Therefore, a "nontraditional" ground vibration testing approach was taken. The objective of the QuietSpike (TM) build-up ground testing approach was to ultimately obtain confidence in the F-15B Quietspike(TM) finite element model (FEM) to be used for the flutter analysis. In order to obtain the F15B QS FEM with reliable foundation stiffness between the QS and the F-15B radar bulkhead as well as QS modal characteristics, several different GVT configurations were performed. EAch of the four GVT's performed had a specific objective. The overall intent was to provide adequate data which would replicate a "traditional" F-15B QS GVT with actual ready-for-flight hardware. NASA Dryden was tasked with the conduct of the 1st, 2nd and 4th GVT and the 3rd GVT was GAC's responsibility. In order for this build-up GVT approach to be feasible, it was absolutely critical that each GVT configuration matched as closely as possible the connection interface configuration between the and aircraft bulkhead.

Spivey, Natalie D.↗

Full circle mechanical dynamic characterization including experimental modal analysis and finite element analysis

During operation, it was observed that a specific mechanical system experienced undesirable vibration and it became necessary to understand and mitigate this phenomenon. This document investigates the tools, methodology, and results of the dynamic characterization of the system. The characterization makes use of the experimental modal analysis (EMA) methods of single input multiple output (SIMO) and single input single output (SISO). The validity of the theory of reciprocity is confirmed to minimize measurement error, cost, and time of repeat testing. Finite element analysis (FEA) is used in choosing transducer and modal impact locations to adequately characterize the system. Single degree of freedom (SDOF) and multiple degree of freedom (MDOF) curve fitting is used to fully characterize the system’s mode shapes and natural frequencies. The EMA characterization results are used to modify and validate the FEA model so that FEA can be used to model potential structural modifications to the system to mitigate the undesirable vibration. Structural modifications are chosen, implemented, and their effectiveness is quantified using EMA. Finally, a qualitative evaluation of the methodology of FEA validation by EMA and tuning of the model to match the experimental results is discussed.

42 ENGINEERING↗

A comparative study of multimodal data fusion strategies for planetary spectroscopy

Integrating heterogeneous data sources can improve scientific inference when different modalities capture complementary information, but doing so is challenging in high-dimensional, small-sample settings. In spectroscopy for planetary exploration, Laser-Induced Breakdown Spectroscopy (LIBS), Raman Spectroscopy (Raman), Visible Infrared Spectroscopy (VISIR), and Mid-Infrared Spectroscopy (MIR) each examine different aspects of composition and mineralogy, raising fundamental questions about when and how data fusion improves predictive performance. Using a Mars-relevant set of geologic standards with measurements from all four modalities, we present a rigorous systematic evaluation of four data fusion strategies: low-level (data) fusion, mid-level (feature) fusion, high-level (decision) fusion, and residual-boosting (sequential) fusion. We assess performance in predicting oxide composition via nested cross-validation and corrected significance testing to evaluate whether data fusion improves upon single-modality baselines. We show that data fusion does not uniformly improve accuracy, and that observed gains are modest, oxide-dependent, and sensitive to modality and model structure. To move beyond aggregate accuracy metrics, we use model coefficients, permutation importance, and residual gain analysis to examine how the fusion models weight individual modalities and to identify patterns of apparent complementarity or redundancy. Though focused on spectroscopy for planetary exploration, our framework for data fusion evaluation and interpretation extends to other scientific domains with heterogeneous and scarce data and provides a principled approach evaluating data fusion strategies, interpreting modality contributions, and understanding tradeoffs among data fusion strategies.

97 MATHEMATICS AND COMPUTING↗