Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Material properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

Progressive Failure Analysis Correlation with Notched Composite Laminate Test Data

Testing of small and intermediate laminate panels with notches was performed and Progressive Failure Analyses (PFA) models were developed for aid in test planning and for correlation with the test data. Two progressive damage failure models were included in the study: the commercially available Abaqus built-in damage model and COmplete STress Reduction (COSTR) damage model developed at NASA Langley Research Center (LaRC). The finite elements models used for the analysis were developed using shell elements. The pre-test PFA results obtained from the two damage models were compared to test data. Then a post-test PFA with updated material properties based on additional available material property data was executed with the COSTR damage model and compared to the test data. The panels tested in compression all exhibited less scatter in the failure load with self-similar failure behavior. The panels tested in tension exhibited more scatter in the failure load with a failure mode that included delamination of plies. However, a self-similar crack path was also observed as the overall failure mode for all panels tested. When comparing test data to the pre-test analysis results, both damage models with shell element models were considered adequate for predicting the behavior and failure load of both the small and intermediate panels when tested in compression. However, for the tension load cases, larger differences were observed between the test and analysis results. When comparing test data to the post-test analysis performed using the COSTR damage model, better correlation was observed. However, large discrepancies were still observed for the tension load cases. Consequently, a higher fidelity finite element model including solid elements for sub-laminates and the modeling of cohesive layers between sub-laminate layers is recommended for tension loading of notched composite laminates.

Damage Model,Progressive Failure Analysis,Open Hol↗

Thermal Protection System Evaluation Using Arc-jet Flows: Flight Simulation or Research Tool?

The arc-jet has been used to evaluate thermal protection systems (TPS) and materials for the past forty years. Systems that have been studied in this environmerd include ablators, active, and passive TPS concepts designed for vehicles entering planetary and Earth atmospheres. The question of whether arc-jet flow can simulate a flight environment or is it a research tool that provides an aero-thermodynamic heating environment to obtain critical material properties will be addressed. Stagnation point tests in arc-jets are commonly used to obtain material properties such as mass loss rates, thermal chemical stability data, optical properties, and surface catalytic efficiency. These properties are required in computational fluid dynamic codes to accurately predict the performance of a TPS during flight. Special facilities have been developed at NASA Ames Research Center to approximate the flow environment over the mid-fuselage and body flap regions of proposed space-planes type vehicles. This paper compares flow environments generated in flight over a vehicle with those created over an arc-jet test articles in terms of scale, chemistry, and fluid dynamic properties. Flight experiments are essential in order to validate the material properties obtained from arc-jet tests and used to predict flight performance of any TPS being considered for use on a vehicle entering the Earth atmosphere at hypersonic speed.

Stewart, David A.↗

Applications of Transient Grating Spectroscopy to Radiation Materials Science

Radiation damage is an inherently multi-scale phenomenon, with much of the key material evolution occurring at the mesoscale. Current techniques for the direct interrogation of material property changes due to irradiation either function with very small volumes, such as in-situ TEM, cannot cover the full range of defect populations produced, such as in positron annihilation spectroscopy, or requires destruction of the test material, such as in standard or micromechanical testing. In addition, the ultimate quantities of interest to radiation materials scientists are the changes in key material properties with irradiation. These include stiffness, ductility, and thermal conductivity for structural materials, and optical properties such as index of refraction or changes in transmittance spectra for optically active materials. The latter of these are often correlated directly to stress- or thermally-induced changes, themselves a function of the specific defect populations responsible for their change. The rapid study of such a mesoscale phenomenon requires an inherently mesoscale technique, where multiple quantities of interest can be accurately measured in very short times. Determining the sensitivity of any technique with known certainly is of critical importance to qualifying a new technique to measure in-situ material property changes during irradiation. In this paper, we present the new applicability of an existing technique, known as transient grating (TG) spectroscopy, to rapidly and accurately study key problems in radiation materials science. Results quantifying the absolute sensitivity of the technique are presented, alongside molecular dynamics (MD) simulations of the TG spectroscopy process to gauge direct agreement between theory, simulation, and experiment. An example problem of interest is demonstrated as an illustration of what is possible, showing elastic and thermal changes in irradiated silicon carbide (SiC) films. Finally, future work to quantify the effects of experimentally-simulated radiation defects is proposed, in support of building a database to use TG spectroscopy to deconvolve irradiated material property changes in-situ in terms of the defect populations responsible for their evolution. The application of the TG spectroscopy technique to in-situ radiation materials science has the potential to answer long-standing questions in the field, relating to ion beam rastering, the onset of void swelling, and direct measurement of radiation-created point defect concentrations. Before it can do so, the technique must carefully be analyzed and tuned to increase its sensitivity, the certainty of its results, and the ability to predict radiation-induced changes by simulations must be developed. Making such measurements in-situ with the aid of predictive MD simulations has the potential to elucidate mechanisms of radiation damage accumulation, as well as more rapidly qualify radiation-resistant alloys for service in nuclear systems. Work is underway to build this database of experimentally-simulated radiation-produced defects, which will be combined and compared with actual irradiated materials for eventual in-situ deconvolution of the TG signal into the defect populations responsible for irradiation-induced microstructural change. (authors)

36 MATERIALS SCIENCE↗

An overview of self-consistent methods for fiber-reinforced composites

The Walker et al. (1989) self-consistent method to predict both the elastic and the inelastic effective material properties of composites is examined and compared with the results of other self-consistent and elastically based solutions. The elastic part of their method is shown to be identical to other self-consistent methods for non-dilute reinforced composite materials; they are the Hill (1965), Budiansky (1965), and Nemat-Nasser et al. (1982) derivations. A simplified form of the non-dilute self-consistent method is also derived. The predicted, elastic, effective material properties for fiber reinforced material using the Walker method was found to deviate from the elasticity solution for the v sub 31, K sub 12, and mu sub 31 material properties (fiber is in the 3 direction) especially at the larger volume fractions. Also, the prediction for the transverse shear modulus, mu sub 12, exceeds one of the accepted Hashin bounds. Only the longitudinal elastic modulus E sub 33 agrees with the elasticity solution. The differences between the Walker and the elasticity solutions are primarily due to the assumption used in the derivation of the self-consistent method, i.e., the strain fields in the inclusions and the matrix are assumed to remain constant, which is not a correct assumption for a high concentration of inclusions.

Gramoll, Kurt C.↗

Thermally induced stresses in cross-ply composite tubes

An approximate solution for determining stresses in cross-ply composite tubes subjected to a circumferential temperature gradient is presented. The solution is based on the principle of complementary virtual work (PCVW) in conjunction with a Ritz approximation on the stress field and accounts for the temperature dependence of material properties. The PCVW method is compared with a planar elasticity solution using temperature-independent material properties and a Navier approach. The net effect of including temperature-dependent material properties is that the peak absolute values of the stresses are reduced. The dependence of the stresses on the circumferential location is also reduced in comparison with the case of temperature-independent properties.

Hyer, M. W.↗

Controlling the Casimir force via the electromagnetic properties of materials

The control of the Casimir force between two parallel plates can be achieved through adjusting the frequency-dependent electromagnetic properties of materials of the two plates. We show that, for different plate separations, the main contribution to the Casimir force comes from different frequency regions: For smaller (larger) separation, it comes from the higher (lower) frequency region. When the separation of the plates increases, the Casimir force can vary from attractive to repulsive and/or vice versa, by selecting the two plates with suitable electromagnetic properties. We discuss how a restoring Casimir force, which varies from repulsive to attractive by increasing the separation, can be realized and that the stable equilibrium is formed at zero Casimir force.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Toward efficient elastocaloric systems: Predicting material thermal properties with high fidelity

A critical need to accurately model thermal behaviors of materials that exhibit strong elastocaloric effects, including predicting the effects themselves at varying stresses and temperatures, has been addressed using a simple and versatile physics-based approach. The key factor leading to the high precision is approximating the underlying elastic phase transition as a smooth modification of lattice entropy between coexisting phases. Once the phase transformation entropy is modeled to match experimentally measured strain as a function of temperature and applied stress, estimating the heat capacity, entropy, and isothermal entropy and adiabatic temperature changes in temperature-stress coordinates becomes straightforward. This approach provides insight into how thermal properties of elastocaloric materials vary through the transition based on strain measurements that are simple to perform and interpret. In addition to aiding in the rapid evaluation of new and existing elastocaloric materials, this advance is expected to prove invaluable for accurate heat transfer modeling aimed at designing efficient regenerative elastocaloric cooling devices.

36 MATERIALS SCIENCE↗

Advanced Materials and Additive Manufacturing for Phase Change Thermal Energy Storage and Management: A Review

Abstract Phase change materials (PCMs) can enhance the performance of energy systems by time shifting or reducing peak thermal loads. The effectiveness of a PCM is defined by its energy and power density—the total available storage capacity (kWh m −3 ) and how fast it can be accessed (kW m −3 ). These are influenced by both material properties as well as geometry of the energy systems; however, prior efforts have primarily focused on improving material properties, namely, maximizing latent heat of fusion and increasing thermal conductivity. The latter is often at the expense of the former. Advanced manufacturing techniques hold tremendous potential to enable co‐optimization of material properties and device geometry, while potentially reducing material waste and manufacturing time. There is an emerging body of research focused on additive manufacturing of PCM composites and devices for thermal energy storage (TES) and thermal management. In this article, the fundamentals and applications of PCMs are reviewed and recent additive manufacturing advances in latent heat TES for both the PCM composite and associated heat exchanger are discussed. A forward‐looking perspective on the future and potential of PCM additive manufacturing for TES and thermal management is provided.

25 ENERGY STORAGE↗

Materials structure–property factorization for identification of synergistic phase interactions in complex solar fuels photoanodes

Abstract Properties can be tailored by tuning composition in high-order composition spaces. For spaces with complex phase behavior, modeling the properties as a function of composition and phase distribution remains a formidable challenge. We present materials structure–property factorization (MSPF) as an approach to automate modeling of such data and identify synergistic phase interactions. MSPF is an interpretable machine learning algorithm that couples phase mapping via Deep Reasoning Networks (DRNets) to matrix factorization-based modeling of the representative properties of each phase in a dataset. MSPF is demonstrated for Bi–Cu–V oxide photoanodes for solar fuel generation, which contains 25 different phase combinations and correspondingly exhibits complex composition-structure-photoactivity relationships. Comparing the measured photoactivity to a learned model for non-interacting phases, synergistic phase interactions are identified to guide further photoactivity optimization and understanding. MSPF identifies synergistic interactions of a BiVO 4 -like phase with both Cu 2 V 2 O 7 -like and CuV 2 O 6 -like phases, creating avenues for understanding complex photoelectrocatalysts.

36 MATERIALS SCIENCE↗

Phase Transformations among TiO2 Polymorphs

Polymorphs widely exist in nature and synthetic systems and are well known to determine material properties. Understanding phase transformation mechanisms among polymorphs enables the design of structures and tuning of phases to tailor material properties. However, current understanding is limited due to the lack of direct observations that track the processes and the structural evolution is not known at atomic scale. Here, integrating (semi) in situ transmission electron microscopy and density functional theory, we report atomic structural evolutions of phase transformation from anatase (A) to rutile (R), brookite (B), R-phase, and TiO. Besides the consistent paths with previous reports, we discover several unreported paths, including a [001] direction and (020) plane of anatase to [100]A and (011)R of rutile, respectively, ( , ) and , . Density functional theory analysis elucidates atomic structural evolution during the processes and over 16% of Ti-O bonds break and reform during the processes with energy barriers of ~0.7-1.0 eV per TiO2 formula unit. Under electron-beam irradiation, anatase particles transform into TiO2-R phase or TiO at high or room temperature, respectively. We also reveal the anisotropic nature of electron-beam effect, which is seldom discussed: dependence of crystallographic orientation with respect to electron-beam irradiation direction. Understanding the atomic structural evolution sheds light on interpreting and controlling TiO2 polymorphs and interface structures for various applications. The revealed electron-beam effects in our work provide guidance for in situ transmission electron microscopy studies.

Song, Miao↗

Carbon Characterization Laboratory Report

The newly completed Idaho National Laboratory (INL) Carbon Characterization Laboratory (CCL) is located in Lab-C20 of the Idaho National Laboratory Research Center. This laboratory was established under the Next Generation Nuclear Plant (NGNP) Project to support graphite research and development activities. The CCL is designed to characterize and test carbon-based materials such as graphite, carbon-carbon composites, and silicon-carbide composite materials. The laboratory is fully prepared to measure material properties for nonirradiated carbon-based materials. Plans to establish the laboratory as a radiological facility within the next year are definitive. This laboratory will be modified to accommodate irradiated materials, after which it can be used to perform material property measurements on both irradiated and nonirradiated carbon-based material. Instruments, fixtures, and methods are in place for preirradiation measurements of bulk density, thermal diffusivity, coefficient of thermal expansion, elastic modulus, Young’s modulus, Shear modulus, Poisson ratio, and electrical resistivity. The measurement protocol consists of functional validation, calibration, and automated data acquisition.

36 MATERIALS SCIENCE↗

Thermophysical and Optical Properties of Materials Considered for Use on the LDSD Test Vehicle

In June 2014, the first of multiple flights in the Low Density Supersonic Decelerator (LDSD) technology development program took place and successfully demonstrated a Supersonic Inflatable Aerodynamic Decelerator (SIAD) in Mars-like conditions. Although the primary goal of the technology program was the development of new decelerators for landing heavier payloads on Mars, the low-cost thermal design of the test vehicle was only possible through the innovative use of a combination of both commercial off the shelf (COTS) and aerospace grade materials. As a result, numerous thermophysical and optical property measurements were undertaken to characterize material candidates before the final material selection was made. This paper presents thermophysical and optical property measurements performed over the course of the LDSD test vehicle development, including those not ultimately selected for use on the vehicle. These properties are compared and contrasted with the existing measurements available in previous literature.

Redmond, Matthew↗

Performance Evaluation of K-DEMO Cable-in-conduit Conductors Using the Florida Electro-Mechanical Cable Model

The United States ITER Project Office (USIPO) is responsible for design of the Toroidal Field (TF) insert coil, which will allow validation of the performance of significant lengths of the conductors to be used in the full scale TF coils in relevant conditions of field, current density and mechanical strain. The Japan Atomic Energy Agency (JAEA) will build the TF insert which will be tested at the Central Solenoid Model Coil (CSMC) Test facility at JAEA, Naka, Japan. Three dimensional mathematical model of TF Insert was created based on the initial design geometry data, and included the following features: orthotropic material properties of superconductor material and insulation; external magnetic field from CSMC, temperature dependent properties of the materials; pre-compression and plastic deformation in lap joint. Major geometrical characteristics of the design were preserved including cable jacket and insulation shape, mandrel outline, and support clamps and spacers. The model is capable of performing coupled structural, thermal, and electromagnetic analysis using ANSYS. Numerical simulations were performed for room temperature conditions; cool down to 4K, and the operating regime with 68kA current at 11.8 Tesla background field. Numerical simulations led to the final design of the coil producing the required strain levels on the cable, while simultaneously satisfying the ITER magnet structural design criteria.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Linear and Nonlinear Solvers for Simulating Multiphase Flow within Large-Scale Engineered Subsurface Systems

Simulation of multiphase flow in the subsurface is well-known to be computationally challenging. While there have been many studies that have explored approaches to overcoming these challenges, they often utilize relatively simple case studies. In this paper, we focus on the unique numerical challenges posed by modeling large-scale engineered subsurface systems, characterized by discrete features embedded in a heterogeneous natural subsurface setting. The man-made features such as shafts, tunnels, and barriers often cause multiple challenges in modeling the domain for multiphase porous media flow. This flow scenario can have a wide range of applications such as nuclear waste repositories, enhanced recovery of a petroleum reservoir, geothermal engineering, and carbon sequestration. An example of these severe numerical challenges is the case of performance assessment (PA) for Waste Isolation Pilot Plant (WIPP), the only operating deep geological repository in the US, which simulates extreme material properties of bedded salt rock formation and extreme contrast due to open excavation next to the formation. The models have extremes not only of permeability and porosity but also of the constitutive models needed for multiphase flow; additionally, they have process models like salt creep closure reducing porosity over time, fracturing in clay and anhydrite interbeds of the bedded salt, gas generation from the waste materials, and unintentional human borehole intrusions in some scenarios. Numerical simulations require the solution of coupled systems of nonlinear PDEs; in our work, we use the open-source simulator PFLOTRAN which is based on Finite Volume discretization. The solution of the nonlinear equations requires use of the Newton-Raphson iteration at each time step, which entails the solution of the linearized Jacobian system at each iteration. The effects of all the processes (i.e., large number of unknowns, highly nonlinear constitutive relations, large contrasts in material properties in short distances) lead to an ill-conditioned Jacobian matrix that severely challenges traditional linear solver, i.e., stabilized biconjugate gradient with block Jacobi incomplete LU preconditioner (BCGS-ILU) leading to non-convergence for traditional Newton-Raphson nonlinear solver causing unacceptably long computation time for each model. This paper presents linear solvers such as constrained pressure residual (CPR) two-stage preconditioner with alternate-block-factorization (ABF) and quasi- implicit pressure and explicit saturation (QIMPES) decouplers and flexible generalized residual solver (FGMRES). The new general-purpose nonlinear solver, Newton trust-region dogleg Cauchy (NTRDC), is also introduced to resolve extreme nonlinearities in the models. We demonstrate the effectiveness of each method relative to the default BCGS-Newton solver. The two best cases had nearly 50 times speed-up and achieved completion of a simulation in 14 hours that never completed due to non-convergence with the default solver. We also investigate the strong scalability of each method and discuss some of the deficiencies found for Block Jacobi preconditioner using parallel domain decomposition, and node packing effects of modern processor architecture.

Preconditioner, Nonlinear, Porous media, Multiphas↗

Microcracking of Materials for Space

The effect of thermal-cycling-induced microcracking in fiber-reinforced polymer matrix composites is studied. Specific attention is focused on microcrack density as a function of the number of thermal cycles, and the effect of microcracking on the dimensional stability of composite materials. Changes in laminate coefficient of thermal expansion (CTE) and laminate stiffness are of primary concern. Included in the study are materials containing four different Thornel fiber types: a PAN-based T50 fiber and three pitch-based fibers, P55, P75, and P120. The fiber stiffnesses range from 55 Msi to 120 Msi. The fiber CTE's range from -0.50 x 1O(exp -6)/degrees F to -0.80 x 10(exp -6)/degrees F. Also included are three matrix types: Fiberite's 934 epoxy, Amoco's ERL1962 toughened epoxy, and YLA's RS3 cyanate ester. The lamination sequences of the materials considered include a cross-ply configuration, [0/90](sub 2s), and two quasi-isotropic configurations, [0/+45/-45/90](sub s), and [0/+45/90/-45](sub s). The layer thickness of the materials range from a nominal 0.001 in. to 0.005 in. In addition to the variety of materials considered, three different thermal cycling temperature ranges are considered. These temperature ranges are +/-250 degrees F, +/-l5O degrees F, and +/-50 degrees F. The combination of these material and geometric parameters and temperature ranges, combined with thermal cycling to thousands of cycles, makes this one of the most comprehensive studies of thermal-cycling-induced microcracking to date. Experimental comparisons are presented by examining the effect of layer thickness, fiber type, matrix type, and thermal cycling temperature range on microcracking and its influence on the laminates. Results regarding layer thickness effects indicate that thin-layer laminates microcrack more severely than identical laminates with thick layers. For some specimens in this study, the number of microcracks in thin-layer specimens exceeds that in thick-layer specimens by more than a factor of two. Despite the higher number of microcracks in the thin-layer specimens, small changes in CTE after thousands of cycles indicate that the thin-layer specimens are relatively unaffected by the presence of these cracks compared to the thick-layer specimens. Results regarding fiber type indicate that the number of microcracks and the change in CTE after thousands of cycles in the specimens containing PAN-based fibers are less than in the specimens containing comparable stiffness pitch-based fibers. Results for specimens containing the different pitch-based fibers indicate that after thousands of cycles, the number of microcracks in the specimens does not depend on the modulus or CTE of the fiber. The change in laminate CTE does, however, depend highly on the stiffness and CTE of the fiber. Fibers with higher stiffness and more negative CTE exhibit the lowest change in laminate CTE as a result of thermal cycling. The overall CTE of these specimens is, however, more negative as a result of the more negative CTE of the fiber. Results regarding matrix type based on the +/-250 degree F temperature range indicate that the RS3 cyanate ester resin system exhibits the greatest resistance to microcracking and the least change in CTE, particularly for cycles numbering 3000 and less. Extrapolations to higher numbers of cycles indicate, however, that the margin of increased performance is expected to decrease with additional thermal cycling. Results regarding thermal cycling temperature range depend on the matrix type considered and the layer thickness of the specimens. For the ERL1962 resin system, microcrack saturation is expected to occur in all specimens, regardless of the temperature range to which the specimens are exposed. By contrast, the RS3 resin system demonstrates a threshold effect such that cycled to less severe temperature ranges, microcracking does not occur. For the RS3 specimens with 0.005 in. layer thickness, no microcracking or changes in CTE are observed in specimens cycled between +/-150 degree F or +/- 50 degree F. For the RS3 specimens with 0.002 in. layer thickness, no microcracking or changes in CTE are observed in specimens cycled between +/-50 degree F. Results regarding laminate stiffness indicate negligible change in laminate stiffness due to thermal cycling for the materials and geometries considered in this investigation. The study includes X-ray examination of the specimens, showing that cracks observed at the edge of the specimens penetrate the entire width of the specimen. Glass transition temperatures of the specimens are measured, showing that resin chemistry is not altered as a result of thermal cycling. Results are also presented based on a one-dimensional shear lag analysis developed in the literature. The analysis requires material property information that is difficult to obtain experimentally. Using limited data from the present investigation, material properties associated with the analysis are modified to obtain reasonable agreement with measured microcrack densities. Based on these derived material properties, the analysis generally overpredicts the change in laminate CTE. Predicted changes in laminate stiffness show reasonable correlation with experimentally measured values.

Brown, Timothy L.↗

Materials for Advanced Ultrasupercritical Steam Turbines Task 3: Materials for Non-Welded Rotors, Buckets, and BoltingMaterials for Advanced Ultrasupercritical Steam Turbines

The primary objective of the task was to characterize the materials suitable for mechanically coupled rotor, buckets and bolting operating with an inlet temperature of 760°C (1400°F). A previous study DOE-FC26-05NT42442, identified alloys such as Haynes®282®, Nimonic 105, Inconel 740, Waspaloy, Nimonic 263, and Inconel 617 as potential alloys that met the requirements for the necessary operating conditions. Of all the identified materials, Waspaloy has been widely utilized in the aviation industry in the form of disk and other smaller forgings, and sufficient material properties and vendor experience exist, for the design and manufacture of large components. The European program characterizing materials for A-USC conditions are evaluating Nimonic 263 and Inconel 617 for large components. Inconel 740 has been studied extensively as a part of the boiler consortium and is code approved. Therefore, the consortium focused efforts in the development of material properties for Haynes®282® and Nimonic 105 to avoid replicative efforts and provide material choices/trade off during the detailed design of large components. Commercially available Nimonic 105 and Haynes®282® were evaluated for microstructural stability by long term thermal exposure studies. Material properties requisite for design such as tensile, creep / rupture, low cycle fatigue, high cycle fatigue, fatigue crack growth rate, hold-time fatigue, fracture toughness, and stress relaxation are documented in this report. A key requisite for the success of the program was a need demonstrate the successful scale up of the down-selected alloys, to large components. All property evaluations in the past were performed on commercially available bar/billet forms. Components in power plant equipment such as rotors and castings are several orders in magnitude larger and there is a real need to resolve the scalability issue. Nimonic 105 contains high volume fraction y’ [>50%], and hence the alloy is best suited for smaller forging and valve internals, bolts, smaller blades. Larger Nimonic 105 forgings, would precipitate y’ during the surface cooling during forging, leading to surface cracks. The associate costs in forging Nimonic 105 to larger sizes [hotter dies, press requirements], were beyond the scope of this task and not investigated further. Haynes®282® has 20 - 25% volume fraction y’ was a choice for large components, albeit untested. A larger ingot diameter is pre-requisite for a larger diameter forging and achieves the “typically” accepted working ratio of 2.5-3:1. However, Haynes®282® is manufactured via a double melt process [VIM-ESR] limited by size [<18-16” diameter], which limited the maximum size of the final forging. The report documents the development of a 24” diameter triple melt ingot, surpassing the current available technology. A second triple melt ingot was manufactured and successfully forged into a 44” diameter disk. The successful developments in triple melting process and the large diameter forging of Haynes®282® resolved the scalability issues and involved the first of its kind attempt in the world for this alloy. The complete characterization of Haynes®282® forging was performed and documented in this report. The dataset from the commercially available Haynes®282® [grain size ASTM 3-4] and the finer grain size disk forging [ASTM 8-9] offer an additional design tradeoff to balance creep and fatigue during the future design process.

Saha, Deepak↗

Project 7.3 Characterization of Kevlar®-reinforced Composites for Predictive Simulation

The IACMI 7.3 project between DuPont and Purdue University required the mechanical testing of a 2x2 twill Kevlar® weave with Hexion EPIKOTE resin. The tension, shear, flexure, and compressive behavior of this material system was characterized, and the results can be seen in Table 1. These material properties can now be further evaluated for use in performance simulations of automotive components to represent the properties of composites based on woven materials containing Kevlar. This report will provide details regarding the effort required to arrive at these material properties.

36 MATERIALS SCIENCE↗