SEARCH · Engineering Papers

Results for “Magnetic”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

All sources NASA NTRS DOE OSTI

DOE OSTI2023

Superconductivity and magnetic and transport properties of single-crystalline CaK ( Fe 1 – x Cr x ) 4 As 4

Members of the CaK (Fe 1–x Cr x ) 4 As 4 series have been synthesized by high-temperature solution growth in single-crystalline form and characterized by x-ray diffraction, elemental analysis, and magnetic and transport measurements. The effects of Cr substitution on the superconducting and magnetic ground states of CaKFe 4 As 4 (T c = 35 K) have been studied. These measurements show that the superconducting transition temperature decreases monotonically and is finally suppressed below 1.8 K as x is increased from 0 to 0.038. For x-values greater than 0.012, signatures of a magnetic transition can be detected in magnetic measurements with the associated features in the transport measurements becoming detectable for x ≥ 0.038. The magnetic transition temperature increases in a roughly linear manner as Cr substitution increases. A temperature-composition (T – x) phase diagram is constructed, revealing a half-dome of superconductivity with the magnetic transition temperature, T*, appearing near 22 K for x ~ 0.017 and rising slowly up to 60 K for x ~ 0.077. The T – x phase diagrams for CaK (Fe 1–x T x ) 4 As 4 for T = Cr and Mn are essentially the same despite the nominally different band filling; this is in marked contrast to T = Co and Ni series for which the T – x diagrams scale by a factor of 2, consistent with the different changes in band filling Co and Ni would produce when replacing Fe. Superconductivity of CaK (Fe 1–x Cr x ) 4 As 4 is also studied as a function of magnetic field. A clear change in $H^{'}_{c2}$ (T)/T c , where $H^{'}_{c2}$ (T) is dH c2 (T)/dT, at x ~ 0.012 is observed and probably is related to a change of the Fermi surface due to magnetic order. Further, coherence length and the London penetration depths are also calculated based on H c1 and H c2 data. Both of them as a function of x show changes near x = 0.012, again consistent with Fermi surface changes associated with the magnetic ordering seen for higher x-values.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2024

Effects of pressure on the electronic and magnetic properties of bulk NiI 2

Transition metal dihalides have recently garnered interest in the context of two-dimensional van der Waals magnets as their underlying geometrically frustrated triangular lattice leads to interesting competing exchange interactions. In particular, NiI 2 is a magnetic semiconductor that has been long known for its exotic helimagnetism in the bulk. Recent experiments have shown that the helimagnetic state survives down to the monolayer limit with a layer-dependent magnetic transition temperature that suggests a relevant role of the interlayer coupling. Here, we explore the effects of hydrostatic pressure as a means to enhance this interlayer exchange and ultimately tune the electronic and magnetic response of NiI 2 . We study first the evolution of the structural parameters as a function of external pressure using first-principles calculations combined with x-ray diffraction measurements. We then examine the evolution of the electronic structure and magnetic exchange interactions via first-principles calculations and Monte Carlo simulations. Further, we find that the leading interlayer coupling is an antiferromagnetic second-nearest-neighbor interaction that increases monotonically with pressure. The ratio between isotropic third- and first-nearest-neighbor intralayer exchanges, which controls the magnetic frustration and determines the magnetic propagation vector q of the helimagnetic ground state, is also enhanced by pressure. As a consequence, our Monte Carlo simulations show a monotonic increase in the magnetic transition temperature, indicating that pressure is an effective means to tune the magnetic response of NiI 2 .

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2024

Controlling topology through targeted composite symmetry manipulation in magnetic systems

The possibility of selecting magnetic space groups by orienting the magnetization direction or tuning magnetic orders offers a vast playground for engineering symmetry-protected topological phases in magnetic materials. In this work, we study how selective tuning of symmetry and magnetism can influence and control the resulting topology in a two-dimensional magnetic system, and we illustrate such a procedure in the ferromagnetic monolayer MnPSe 3 . Density functional theory calculations reveal a symmetry-protected accidental semimetallic (SM) phase for out-of-plane magnetization, which becomes an insulator when the magnetization is tilted in-plane, reaching band-gap values close to 100 meV. We identify an order-2 composite antiunitary symmetry and threefold rotational symmetry that induce the band crossing, and we classify the possible topological phases using symmetry analysis, which we support with tight-binding and k · p models. Breaking of inversion symmetry opens a gap in the SM phase, giving rise to a Chern insulator. We demonstrate this explicitly in the isostructural Janus compound Mn 2 ⁢P 2 ⁢S 3 ⁢Se 3 , which naturally exhibits Rashba spin-orbit coupling that breaks inversion symmetry. Our results map out the phase space of topological properties of ferromagnetic transition-metal phosphorus trichalcogenides, and they demonstrate the potential of the magnetization-dependent metal-to-insulator transition as a spin switch in integrated two-dimensional electronics.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2020

Tunable magnetic order in low-symmetry SeO 3 ligand linked TM 3 (SeO 3 ) 3 H 2 O ( TM =Mn , Co, and Ni) compounds

The ability to design crystal lattices with specific sublattice geometries has long been sought after especially in the context of harnessing magnetic frustration to elicit emergent physics. One approach which has seen some success recently is to design magnetic sublattices chemically through the use of nonmagnetic linker ligands as scaffolding for the magnetic ions. In this work we report the magnetic properties of one such family of materials, the transition metal (TM) selenite hydrates with chemical formula TM 3 (SeO 3 ) 3 H 2 O. These materials link highly distorted TMO 6 octahedra via nonmagnetic [SeO 3 ] 2+ linkers. Studying members with TM = Mn, Co, and Ni we use magnetic susceptibility and neutron powder diffraction to identify antiferromagnetic order in all three compounds with moderate frustration indexes. A comparison of the magnetic structures suggests that while the overall structure of the SeO 3 scaffolding remains unchanged the TM effects changes in the magnetic properties through tuning the internal bonding parameters and the single-ion physics. Changing from Mn to Co is found to be particularly consequential manifesting changes in both the ordered-moment direction and in the direction of the ordering vector. Field-dependent measurements of the susceptibility and heat capacity reveal metamagnetic transitions in both Mn 3 (SeO 3 ) 3 H 2 O and Co 3 (SeO 3 ) 3 H 2 O indicating nearby magnetic ground states accessible under relatively small applied fields. Density functional theory calculations broadly confirm these results, showing both a sensitivity of the magnetic structure to the TM and its local environment. Although no spin liquid behavior is achieved, these results suggest the fruitfulness of such synthesis philosophies and encourage future work to engender higher frustration in these materials via doping, field, pressure, or larger linker ligands.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Anisotropic magnetism of the Shastry-Sutherland lattice material BaNd 2 PtO 5

For this work, single crystals were grown and characterized to investigate the physical properties and magnetic ground state of BaNd 2 PtO 5 , a candidate to host physics of the Shastry-Sutherland model. Analysis of single crystal x-ray diffraction data yields an updated crystal structure, similar to the prior report but now in space group P4/mbm. Magnetization and specific heat measurements reveal an antiferromagnetic transition at T N =1.9K and a large magnetic anisotropy with in-plane magnetization much larger than out-of-plane magnetization. Single crystal neutron diffraction at zero field reveals a propagation vector of ($\frac{1}{2}$$\frac{1}{2}$$\frac{1}{2}$) for the magnetic ground state as compared to the ($\frac{1}{2}$$\frac{1}{2}$0) wave vector observed in the related body-centered material BaNd 2 ZnO 5 . The ground state is found to be a fully compensated antiferromagnet with diffraction data well fitted within the magnetic space group P S –1 (BNS setting #2.7). The ordered moment is mostly in the basal plane with nearest neighbors forming ferromagnetic dimers, however it also has a finite out-of-plane component unlike the related easy-plane materials BaNd 2 ZnO 5 and BaNd 2 ZnS 5 . Field-induced transitions are observed below T N when the field is applied within the basal plane, and in-plane anisotropy of the associated critical fields is observed. The magnetization is strongly impacted by misalignment of the field away from high symmetry directions. These results suggest complex magnetic structures may arise in the field-induced states, and they highlight the need for extreme care when studying this and related Shastry-Sutherland materials.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Study on Conduction Cooling of Superconducting Magnets for the ILC Main Linac

In the main linac of the International Linear Collider (ILC), superconducting magnets for beam focusing and steering will be located periodically in superconducting RF (SRF) cavity string for beam acceleration in common cryomodules. A concept of conduction cooling of the combined-functioned, splittable superconducting magnets has been proposed and investigated to adapt much different features and to meet different requirements for the superconducting magnet and SRF cavity in fabrication, assembly, and operation. It is required to integrate the superconducting magnet after the SRF cavity string assembly which completed under an ultra-clean environment. The magnet must be conductively cooled down through thermal links to a liquid helium supply pipe. According to this concept, a model magnet development was carried out in cooperation with Fermilab and KEK, and has been demonstrated in KEK superconducting RF test facility (STF). In addition, an important issue has been recently identified. High gradient SRF cavities naturally emit field emission electron flux from the inner surface, so-called dark current. It may pass through the subsequent SRF cavity string and penetrate into the superconducting magnets placed downstream. It may heat up the superconducting coils, and may cause a quench. Therefore, further study on reliable conduction cooling and to secure the superconducting magnet operation with a keeping sufficient safety margin is quite essential. In this paper, we report the installation, the improvement achieved in STF, and the R&D progress in the study on the conduction cooling of the superconducting magnet for the ILC main linac.

43 PARTICLE ACCELERATORS↗

DOE OSTI2021

Topological Magnets: Functions Based on Berry Phase and Multipoles

Macroscopic responses of magnets are often governed by magnetization and, thus, have been restricted to ferromagnets. However, such responses are strikingly large in the newly developed topological magnets, breaking the conventional scaling with magnetization. Taking the recently discovered antiferromagnetic (AF) Weyl semimetals as a prime example, we highlight the two central ingredients driving the significant macroscopic responses: the Berry curvature enhanced because of nontrivial band topology in momentum space, and the cluster magnetic multipoles in real space. The combination of large Berry curvature and multipoles enables large macroscopic responses such as the anomalous Hall and Nernst effects, the magneto-optical effect, and the novel magnetic spin Hall effect in antiferromagnets with negligible net magnetization, but also allows us to manipulate these effects by electrical means. Furthermore, nodal-point and nodal-line semimetallic states in ferromagnets may provide the strongly enhanced Berry curvature near the Fermi energy, leading to large responses beyond the conventional magnetization scaling. These significant properties and functions of the topological magnets lay the foundation for future technological development such as spintronics and thermoelectric technology.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2020

Geometric concepts for stellarator permanent magnet arrays

The development of stellarators that use permanent magnet arrays to shape their confining magnetic fields has been a topic of recent interest, but the requirements for how such magnets must be shaped, manufactured, and assembled remain to be determined. To address these open questions, we have performed a study of geometric concepts for magnet arrays with the aid of the newly developed MAGPIE code. A proposed experiment similar to the National Compact Stellarator Experiment (NCSX) is used as a test case. Two classes of magnet geometry are explored: curved bricks that conform to a regular grid in cylindrical coordinates, and hexahedra that conform to the toroidal plasma geometry. In addition, we test constraints on the magnet polarization. While magnet configurations constrained to be polarized normally to a toroidal surface around the plasma are unable to meet the required magnetic field parameters when subject to physical limitations on the strength of present-day magnets, configurations with unconstrained polarizations are shown to satisfy the physics requirements for a targeted plasma.

stellarator, permanent magnet, optimization↗

DOE OSTI2021

Plasma Guns for Magnetized Fuel Targets for PJMIF

In plasma jet driven magneto-inertial fusion (PJMIF) an array of discrete supersonic plasma jets is used to form a spherically imploding plasma liner, which then compresses a magnetized plasma target to fusion conditions. With funding from ARPA-E’s ALPHA program and from Strong Atomics LLC, HyperJet Fusion Corp and HyperV Technologies Corp. previously developed the plasma guns required for an experimental demonstration of the plasma liner formation part of the concept. A 36-gun demonstration of an imploding spherical plasma liner is currently underway on the PLX facility at Los Alamos National Laboratory. This present project addresses the next step required for a complete PJMIF concept, i.e. developing the magnetized plasma target. We proposed to form the target by stagnating a number of magnetized plasma jets in the center of the target chamber. This is accomplished by adding a bias field coil to the plasma liner gun to form a magnetized plasma jet. This experimental development took place at HyperJet in a geometry replicating the bias field environment that will be seen on a PLX port so the results are directly transferrable to the PLX experiment. The objective of this effort was the technical development and characterization of a new magnetized plasma jet using a high-performance, high momentum flux, contoured-gap coaxial plasma gun appropriate for use on the next stage of the PLX experiment. Electromagnetic modeling of the coil indicated the coil was best placed around the aluminum tubes of the gun transmission line, rather than around the chamber port as originally proposed. This maximized field strength in the breech and yielded much better flux linkage between gun electrodes. A 30-turn coil was ultimately implemented, allowing long pulses that could diffuse through the metal walls on the timescale of interest. \machtwo modeling predicted that less capacitance in the main PFN could potentially improve plasma jet velocities due to better matching of the current to the smaller plasma mass and the existing electrode contour designed to suppress blowby. This proved true, as testing showed markedly improved performance when the original 600uF bank was reduced to 400uF. A number of diagnostics were built and/or upgraded in order to characterize the plasma jets, inluding laser interferomtery for density, photodiodes for velocity, Bdot probes for magnetic field measurements, a Triple probe for temperature measurements, and spectroscopy for impurity content. A plasma gun with the 30-turn magnet coil installed, a 70% reduction in gas valve plenum volume, and a 33% reduction in main PFN capacitance produced a dense, high velocity, well magnetized plasma jet. We met or exceeded virtually all of the plasma jet parameter goals. Peak velocity of 135 km/s exceeded the 100 km/s goal by 35%, while the peak density of over 1.0x10 15 cm -3 was 3.3 times the goal of >3.0x10 14 cm -3 . Shot-to-shot repeatability is excellent, with a jitter of less than 300ns observed on the arrival fronts of the photodiode signals from one shot to the next. Average plasma jet lengths of 33cm (at 120km/s) were slightly longer than the 20cm goal, but jets as short as 11.8cm were observed at 135km/s. Mass is much higher than the targeted goal, averaging 106ug per shot compared to 20ug. The magnetic field is still a bit lower than desired, with a maximum to date of ~811G, compared to the goal of 1000G. Average values, though, were typically in the 300-450G range, when measured further downstream after some expected in flight decay. Temperature measurements are still a work in progress. Increasing the B field and completing temperature measurements will be continued on into the ongoing BETHE project.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Magnetic Gears: The Key to Robust, Cost-Effective Hydropower Drivetrains

Based on previous demonstrated success at fabricating 5 and 10 kW scale magnetic gearbox (MGB) prototypes, Emrgy and its partners (the project team) proposed to design and construct a 100 kW scale MGB with a 30:1 gear ratio for the low-head hydro applications. The Statement of Project Objectives included tasks covering: 1) Market Applicability; 2) Technical Metrics; 3) Design (initial); 4) Electromagnetic (EM) Load and Structural Analysis; 5) Modal Analysis; 6) Sealing Design and 7) Final Design during Budget Period 1. Budget Period 2 included tasks covering: 1) Materials Procurement and Test Plan Development; 2) Assembly; and 3) Testing. The Market Applicability study (Task 1) led to a clear conclusion and recommendation toward “Low Head” technologies for maximum market share of both New Stream Reach development as well as powering Non-Powered Dams. The findings of this study also identified the opportunity for a larger scale magnetic gearbox-based drive train as a function of increased torque, as opposed to increased speed. The Technical Metrics Study (Task 2) concluded a horizontal orientation was preferred, examined potential loss mechanisms, concluded that a Halbach Array magnetic design was preferred, established a 30:1 gear ratio as optimal, and established a power rating of 100 kW as optimal. The subsequent initial and final detailed design process included electro-magnetic (EM) load and structural analysis (Task 4), a Modal analysis (for vibration) (Task 5), and a sealing design (Task 6) to assure water impermeability. The final design package (Task 7) included 729 individual parts, 117 unique part numbers, and 15 assemblies. In order to facilitate procurement, the full bill of materials was broken down into several sub-components: 1) custom magnetic parts; 2) custom machined parts; 3) custom casted parts; and 4) commercial off the shelf (COTS) parts. The casted parts were fabricated by Oak Ridge National Laboratory (ORNL) via a Cooperative Research and Development Agreement (CRADA) with Emrgy and funded by the Advanced Manufacturing Office (AMO). The procurement effort (Task 8) ultimately covered three time periods based on challenges encountered in meeting the budgeted cost for the prototype. Following the first effort in the early stages of Budget Period 2 in 2017, a no-cost time extension was granted to seek alternative fabrication and procurement options. The project was re-booted in 2020 based on the new ORNL CRADA that would focus on five (5) of the more difficult and expensive parts using their advanced manufacturing expertise. Procurement efforts for the other custom machined parts resulted in quotations that still exceeded the budget by more than $\$$100k. This was, in part, also due to the concurrent COVID-19 pandemic that caused both supply chain disruptions and labor shortages. As the project continued, pricing and availability degraded further. In Q2 FY’22, it was decided to not proceed with the fabrication of the prototype (Task 9) based on budgetary limitations. Outcomes included a full and detailed design of a 100 kW magnetic gearbox and associated indented bill of materials (BOM) and CAD drawings, a full assembly instruction manual with an associated BOM for materials necessary to support assembly, the fabrication of the double Halbach magnetic array for the rotor/stator system, fabrication of five (5) sand-casted/machined parts (via CRADA with ORNL) and an initial draft of a comprehensive testing plan. The most significant non-outcome was the actual fabrication and testing of the prototype gearbox based on budget limitations. Lessons learned included the need for an Application / Design / Cost trade analysis to better elucidate the cost potential of the MGB in the projected volumes anticipated for future demand. This would better establish the efficacy of the original cost target ($\$$0.80/Watt) and/or the need for reconsideration of designs and applications. Likewise, additional consideration of the prototype nature of the gearbox – single use, short lifetime, etc. - either as a separate exercise or in place of the design process completed, to reduce the cost of the demonstration prototype device. Additionally, project continuity was cited as a significant risk based on the loss of the primary design engineering firm after Budget Period 1. A design analysis exercise was conducted at the conclusion of the project to identify potential areas for cost reduction. One concept considered was the removal of the inner ring of magnets (with associated changes in the outer ring magnets) to enable a horizontal collapse of the design. It was estimated this could reduce cost by 10-25% without impacting performance.

13 HYDRO ENERGY↗

DOE OSTI2024

A Multiphysics Thermoelastoviscoplastic Damage Internal State Variable Constitutive Model including Magnetism

We present a macroscale constitutive model that couples magnetism with thermal, elastic, plastic, and damage effects in an Internal State Variable (ISV) theory. Previous constitutive models did not include an interdependence between the internal magnetic (magnetostriction and magnetic flux) and mechanical fields. Although constitutive models explaining the mechanisms behind mechanical deformations caused by magnetization changes have been presented in the literature, they mainly focus on nanoscale structure–property relations. A fully coupled multiphysics macroscale ISV model presented herein admits lower length scale information from the nanoscale and microscale descriptions of the multiphysics behavior, thus capturing the effects of magnetic field forces with isotropic and anisotropic magnetization terms and moments under thermomechanical deformations. For the first time, this ISV modeling framework internally coheres to the kinematic, thermodynamic, and kinetic relationships of deformation using the evolving ISV histories. For the kinematics, a multiplicative decomposition of deformation gradient is employed including a magnetization term; hence, the Jacobian represents the conservation of mass and conservation of momentum including magnetism. The first and second laws of thermodynamics are used to constrain the appropriate constitutive relations through the Clausius–Duhem inequality. The kinetic framework employs a stress–strain relationship with a flow rule that couples the thermal, mechanical, and magnetic terms. Experimental data from the literature for three different materials (iron, nickel, and cobalt) are used to compare with the model’s results showing good correlations.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Frontiers in Magnetic Materials

Magnetism is crucial to many modern technologies, a driver for condensed matter physics research and one of the most remarkable and diverse properties of matter. We propose to develop understanding of novel magnetism and magnetic related behavior in materials and use this to accelerate the discovery of forefront magnetic materials. The approach is via the connection of magnetic properties to specific structures and materials. Topics that will be addressed are (1) Metallic magnetic materials with unusually low carrier concentrations and/or moments (2) Magnetism arising from unusual chemistry including 4d and 5d magnetism and (3) Materials with strong spin-fluctuations, which can lead to quantum criticality, spin-fluctuation induced superconductivity and other novel quantum behavior. These topics overlap, for example, the 4d ruthenates include ferromagnets (perovskite SrRuO 3 ), extremely high ordering temperature antiferromagnets (honeycomb lattice SrRu 2 O 6 ) and well as quantum materials with strong spin fluctuations (layered perovskite Sr 2 RuO 4 and Sr 3 Ru 2 O 7 ). We will use of density calculations to connect magnetic properties with chemistry and structure and employ phenomenological theories to extend these results to properties that are not directly given by direct first principles methods and we will conduct tests to explore the limitations of density functional approximations and new functionals.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Coupled Experimental/Computational Investigation of the Dynamics of Interacting Magnetized Plasmas

The interaction, or interpenetration, of magnetized plasmas of different density and/or pressure occurs in a wide variety of natural and man-made systems. Such systems include extragalactic jets propagating into the intergalactic medium, solar coronal mass ejections into background solar wind, compact toroid (CT) fueling of magnetic fusion plasmas, and jets of capsule shell impurities into DT fusion fuel, which can lead to enhanced impurity mix in inertial fusion implosions. These plasmas may take the form of jets, with open, helical magnetic structure, or plasma “bubbles” with closed magnetic fields (B-fields), such as spheromaks or CT’s. Such structures, both open and closed B-field cases, can transport heat, particles and magnetic flux or magnetic helicity into background plasma regions. For example, the origin of extragalactic magnetic fields may be due, at least in part, to transport by astrophysical jets. The goal of this proposed work was to elucidate the detailed plasma and magnetic field dynamics of high-density plasma jets (open B-field) and bubbles (closed B-field) propagating into lower density background magnetized plasma through controlled laboratory experiments and closely coupled nonlinear MHD modeling. These experiments were conducted in the HelCat (Helicon-Cathode) linear plasma device at the University of New Mexico (UNM). Plasma jets and bubbles were launched via an existing compact coaxial plasma gun, mounted on the HelCat device. This gun produced plasmas tens of cm in scale and lasting tens of microseconds, thereby allowing detailed multipoint, space- and time-resolved measurements to be made routinely. The experiments were directly modeled using the extended magnetohydrodynamic (XMHD) PERSEUS code, developed at Cornell University [23,24]. Both experimental and numerical modeling work are ongoing. The main results to date are reported here. Additional supplemental funding for one year (8/1/2019 – 7/31/2020) supported numerical investigation of photoionization processes important in many low temperature plasmas, including the HelCat device. Initial results of this modeling work is also reported.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

A Multiphysics Thermoelastoviscoplastic Damage Internal State Variable Constitutive Model including Magnetism

36 MATERIALS SCIENCE↗

DOE OSTI2026

Distortion of a Relativistic Jet Echoing a Magnetic Flux Eruption

Magnetized accretion onto spinning black holes (BHs) can accumulate a large magnetic flux across the event horizon and launch a pair of relativistic jets via the Blandford–Znajek mechanism. In the magnetically saturated (arrested) state, excess magnetic flux is ejected from the BH in episodic magnetic flux eruptions, which result in a significant yet temporary reduction of jet power. We analyze results of a high-resolution 3D general-relativistic magnetohydrodynamic numerical simulation of geometrically thick magnetically saturated accretion onto a high-spin Kerr BH for a single cycle of magnetic flux eruption and accumulation. We show that following an eruption, a weakened jet develops a strong helical distortion with a distinct structure of magnetic fields—the poloidal field along the jet core is unaffected by the eruption; while toroidal field lines, ejected from the BH during the eruption and later readvected onto it, form poloidal “bypasses” along the inner jet sheath. Such a distortion may appear in sources fed by geometrically thick accretion flows as an asymmetric superluminal knot, strongly interacting with the jet sheath along an oblique working surface. The jet section repowered by magnetic flux reaccumulated on the BH is tilted by a few degrees, implying significant variations in radiation boost towards observers of BL Lac blazars. The intrinsic structure of the jet spine is consistent with axisymmetric semi-analytical models.

79 ASTRONOMY AND ASTROPHYSICS↗

DOE OSTI2025

Genetically Controlled Iron Oxide Biomineralization in Encapsulin Nanocompartments for Magnetic Manipulation of a Mammalian Cell Line

Magnetic nanoparticles have proven invaluable for biomechanical investigations due to their ability to exert localized forces. However, cellular delivery of exogenous magnetic agents often results in endosomal entrapment, thereby limiting their utility for manipulating subcellular structures. This study characterizes and exploits fully genetically controlled biomineralization of iron-oxide cores inside encapsulin nanocompartments to enable magnetic-activated cell sorting (MACS) and magnetic cell manipulation. The fraction of MACS-retained cells showed substantial overexpression of encapsulins and exhibited both para- and ferrimagnetic responses with magnetic moments of 10 -15 A m 2 per cell, comparable to standard exogenous labels for MACS. Electron microscopy revealed that MACS-retained cells contained densely packed agglomerates of ≈30 nm iron oxide cores consisting of ultrafine quasicrystalline ordered nuclei within an amorphous matrix of iron, oxygen, and phosphorus. Scanning transmission X-ray microscopy, X-ray absorption spectroscopy, and Raman microspectroscopy confirmed that the iron-oxide species are consistent with ferric oxide (Fe 2 O 3 ). In addition, the encapsulin-overexpressing MACS-retained cells can be manipulated by a magnetic needle and regrown in patterns determined by magnetic gradients. This study demonstrates that the formation of quasicrystalline iron oxide with mixed para/ferrimagnetic behavior in the cytosol of mammalian cells enables magnetic manipulation without the delivery of exogenous agents.

60 APPLIED LIFE SCIENCES↗

DOE OSTI2021

3D printing of anisotropic Sm–Fe–N nylon bonded permanent magnets

Abstract Fabricating a bonded magnet with a near‐net shape in suitable thermoplastic polymer binders is of paramount importance in the development of cost‐effective energy technologies. In this work, anisotropic Sm 2 Fe 17 N 3 (Sm–Fe–N) bonded magnets are additively printed using SmFeN anisotropic magnetic particles in a polymeric binder polyamide‐12 (PA12). The anisotropic SmFeN bonded magnets are fabricated by Big Area Additive Manufacturing followed by post‐printing alignment in a magnetic field. Optimal post‐alignment results in an enhanced remanence of ∼0.68 T in PA12 reflected in a parallel‐oriented (aligned) measured direction. The maximum energy product achieved for the additively printed anisotropic bonded magnet of Sm–Fe–N in PA12 polymer is 78.8 KJ m −3 . Our results show advanced processing flexibility with 3D printing of the development of SmFeN nylon bonded magnets designed for applications with no critical rare earth magnets.

42 ENGINEERING↗

DOE OSTI2022

Itinerant G-type antiferromagnet SrCr 2 As 2 studied by magnetization, heat capacity, electrical resistivity, and NMR measurements

Here, the physical properties of itinerant antiferromagnetic (AFM) SrCr 2 As 2 with body-centered tetragonal ThCr 2 Si 2 structure were investigated in single crystalline and polycrystalline forms by electrical resistivity ρ, heat capacity C p , magnetic susceptibility χ versus temperature T, and magnetization M versus applied magnetic field H isotherm measurements as well as 75 As and 53 Cr nuclear magnetic resonance (NMR) measurements in the wide temperature range T = 1.6–900 K. From the χ(T) and 75 As NMR measurements, the G-type AFM state below T N = 615(15) K has been determined, consistent with the previous neutron-diffraction measurements. Direct evidence of magnetic ordering of the Cr spins was shown by the observation of the 53 Cr NMR spectrum under H = 0. From the χ( T) measurements on single-crystal SrCr 2 As 2 under the two different magnetic field directions H|| ab and H || c in the AFM state, the Cr ordered moments are shown to align along the c axis in the G-type AFM state. The metallic state is directly evidenced by the ρ, C p , and NMR measurements, and the density of states at the Fermi energy $\mathscr{D}$(E F ) in the AFM state is estimated to be 7.53 states/eV f.u. for both spin directions which is almost twice the bare $\mathscr{D}$(E F ) estimated from first-principles calculations, suggesting an enhancement of the conduction-carrier mass by a factor of two in the AFM state. The $\mathscr{D}$(E F ) is found to be nearly constant below at least 100 K and is independent of H. The ρ(T) is found to show T-linear behavior above T N and exhibits positive curvature below T N where significant loss of spin-disorder scattering upon magnetic ordering is observed. The resistivity anisotropy of the compound remains moderate ρ c /ρ a ~ 9 through most of the magnetically ordered phase but shows a rapid increase below 50 K.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗