Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MOLDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
NASA NTRS2018

Determination of Uncertainties for Analytically Derived Material Properties to Be Used in Monte Carlo Based Orion Heatshield Sizing

Ablative materials are often used for spacecraft heatshields to protect underlying structures from the extreme environments associated with atmospheric reentry. NASA's Orion EM-1 capsule has been designed to use a molded Avcoat material system. In order to determine the required heatshield thickness, a Monte Carlo approach to the sizing process was proposed. To perform the Monte Carlo simulation, statistical uncertainties on all material property input parameters were required. Obtaining these values for measured properties is straightforward, however input parameters that are derived analytically have historically used uncertainties based on engineering judgment. A MATLAB program was created to use laboratory generated thermogravimetric analysis (TGA) data to calculate uncertainties on the Arrhenius parameters for molded Avcoat. Uncertainties associated with the normalized ablation rate and pyrolysis gas enthalpy were also generated using a wrapper script and the ACE code. These uncertainties could then be tied directly to measured values of individual elemental constituents. The resulting uncertainty values will allow for a probabilistic sizing approach on molded Avcoat with a higher level of confidence in the input parameters.

material property uncertainties↗
NASA NTRSDate not supplied

Assessment of the Impact of an Advanced Power System on a Turboelectric Single-Aisle Concept Aircraft

Electrified aircraft propulsion concepts show potential in using propulsion airframe inte-gration in order to increase efficiency in flight and therefore decrease fuel burn and emissions.Electrification offers component efficiency values greater than 90 percent, but the loss is in the form of low grade waste heat. A major challenge of electrified aircraft propulsion is managing that heat while minimizing any penalties associated with a thermal management system. This paper explores the effect of two innovations in the management of waste heat at the aircraft system level for a turboelectric single aisle concept. The first innovation is achieving a 3 times reduction in heat by developing high-efficiency components rather than managing the high levels of heat. The second takes advantage of the outer mold line of the aircraft to reject heat directly to the environment passively instead of adding active cooling loops that negatively impact the weight, power, and drag of the aircraft. In order to fully grasp the impact of the advanced power system, we develop methods of modeling the power and thermal management systems to be integrated in the full aircraft conceptual model. We then model the aircraft with a state of the art DC transmission system and active cooling loops as a baseline for our study. Our second model includes the advanced power system with active cooling, which results in a fuel burn reduction of 2.5 percent. Finally, in our third model we assess the benefit of an outer mold line cooling scheme with the advanced power system. The outer mold line cooling scheme with an advanced power system yields an additional 0.8 percent reduction in fuel burn,for an overall fuel burn reduction potential of 3.3 percent in addition to aerodynamic benefits of electrified aircraft propulsion.

Electric Aircraft↗
NASA NTRS2023

Spaceflight Autonomous Multigenerational Microbial Sequencer (SAMMS) in Support of Plant-Growth Systems

As the National Aeronautics and Space Association (NASA) begins to pursue long-duration space flights, they will need to be able to provide astronauts with a nutritious and reliable food source. To meet the administration’s goal of traveling to the Moon and Mars, astronauts will need to begin to grow their own food in space. To protect their food source, extensive monitoring will occur to test for the effects of a space flight environment (e.g., radiation) as well as for early pathogen and disease detection. Genomic sequencing allows for both concerns to be tested on a regular basis. However, NASA’s current sequencer is unable to process plant tissues. Therefore, a novel method for plant DNA extraction using microneedle (MN) patches that will be able to feed into NASA’s existing system, but also require minimal human input is proposed. To support this, the design was broken down into four components (1) MN patch fabrication (2) MN patch extraction, (3) automated sampling motion control, and (4) a processing module. The MN patch is fabricated using a custom mold with conically shaped needles. The mold is filled with Polyvinyl alcohol (PVA) solution and placed in a vacuum desiccator. The mold is left in the vacuum overnight until the patch is dry and ready for use. The protocol was tested with varying pressures, drying times, volume amounts, and preparation methods to determine if highquality needles can be produced. A MN is a method of DNA extraction where the patch is applied to a leaf, the needles penetrate the leaf, breaking the rigid plant cell wall to isolate the DNA. A protocol for this method of extraction was tested to ensure the patch could produce the needed yield and purity. The tests varied by the number of patches, number of applications, and plant type. To automate the MN extraction method, motion control will utilize two separate axis tables which move in the x and y directions. The y-axis table will have an end effector that fits a MN patch and will have the ability to apply the patch to the leaf sample. This end effector will also act as a lid for a downstream processing module. The other axis will position the leaf sample and processing container so that the patch can be applied accurately. The Joint Comprehensive Sequencing System (JCSS) module integrates all the components together. The output of this module feeds into the NASA Charged Information-Storage Polymer Preparation System (CHIPPS) for genomic sequencing. The extraction module operates using a series of syringes and tubing to pump the varying reagents needed for the extraction protocol. The results of the study proved that MN patches are a viable method of DNA extraction. While fabrication of high-quality needles was unsuccessful, the protocol was able to be further developed using centrifugation. The integrated design between the motion control and the JCSS enabled the potential for automation with a complete conceptual design and prototype. Future research and development for this study would include (1) further testing for fabrication (2) expanding the range of plant species compatible with the MN patch, and (3) building a working prototype for the integrated system.

Peter Ling↗
DOE OSTI2014

Methods for integrating a functional component into a microfluidic device

Injection molding is used to form microfluidic devices with integrated functional components. One or more functional components are placed in a mold cavity, which is then closed. Molten thermoplastic resin is injected into the mold and then cooled, thereby forming a solid substrate including the functional component(s). The solid substrate including the functional component(s) is then bonded to a second substrate, which may include microchannels or other features.

47 OTHER INSTRUMENTATION↗
DOE OSTI2014

Turbine component casting core with high resolution region

A hollow turbine engine component with complex internal features can include a first region and a second, high resolution region. The first region can be defined by a first ceramic core piece formed by any conventional process, such as by injection molding or transfer molding. The second region can be defined by a second ceramic core piece formed separately by a method effective to produce high resolution features, such as tomo lithographic molding. The first core piece and the second core piece can be joined by interlocking engagement that once subjected to an intermediate thermal heat treatment process thermally deform to form a three dimensional interlocking joint between the first and second core pieces by allowing thermal creep to irreversibly interlock the first and second core pieces together such that the joint becomes physically locked together providing joint stability through thermal processing.

42 ENGINEERING↗
DOE OSTI2015

Multi-component assembly casting

Multi-component vane segment and method for forming the same. Assembly includes: positioning a pre-formed airfoil component (12) and a preformed shroud heat resistant material (18) in a mold, wherein the airfoil component (12) and the shroud heat resistant material (18) each comprises an interlocking feature (24); preheating the mold; introducing molten structural material (46) into the mold; and solidifying the molten structural material such that it interlocks the pre-formed airfoil component (12) with respect to the preformed shroud heat resistant material (18) and is effective to provide structural support for the shroud heat resistant material (18). Surfaces between the airfoil component (12) and the structural material (46), between the airfoil component (12) and the shroud heat resistant material (18), and between the shroud heat resistant material (18) and the structural material (46) are free of metallurgical bonds.

42 ENGINEERING↗
DOE OSTI2016

LED module with high index lens

An array of housings with housing bodies and lenses is molded, or an array of housing bodies is molded and bonded with lenses to form an array of housings with housing bodies and lenses. Light-emitting diodes (LEDs) are attached to the housings in the array. An array of metal pads may be bonded to the back of the array or insert molded with the housing array to form bond pads on the back of the housings. The array is singulated to form individual LED modules.

36 MATERIALS SCIENCE↗
DOE OSTI2017

LED module with high index lens

An array of housings with housing bodies and lenses is molded, or an array of housing bodies is molded and bonded with lenses to form an array of housings with housing bodies and lenses. Light-emitting diodes (LEDs) are attached to the housings in the array. An array of metal pads may be bonded to the back of the array or insert molded with the housing array to form bond pads on the back of the housings. The array is singulated to form individual LED modules.

36 MATERIALS SCIENCE↗
DOE OSTI2016

DRAPING SIMULATION OF WOVEN FABRICS

Woven fabric composites are extensively used in molding complex geometrical shapes due to their high conformability compared to other fabrics. Preforming is an important step in the overall process, where the two-dimensional fabric is draped to become the three-dimensional shape of the part prior to resin injection. During preforming, the orientation of the yarns may change significantly compared to the initial orientations. Accurate prediction of the yarn orientations after molding is important for evaluating the structural performance of the final part. This paper presents a systematic investigation of the angle changes during the preform operation for carbon fiber twill and satin weave fabrics. Preforming experiments were conducted using a truncated pyramid mold geometry designed and fabricated at the General Motors Research Laboratories. Predicted results for the yarn orientations were compared with experimental results and good agreement was observed

42 ENGINEERING↗
DOE OSTI2021

Fiber attach enabled wafer level fanout

A package assembly includes a silicon photonics chip having an optical waveguide exposed at a first side of the chip and an optical fiber coupling region formed along the first side of the chip. The package assembly includes a mold compound structure formed to extend around second, third, and fourth sides of the chip. The mold compound structure has a vertical thickness substantially equal to a vertical thickness of the chip. The package assembly includes a redistribution layer formed over the chip and over a portion of the mold compound structure. The redistribution layer includes electrically conductive interconnect structures to provide fanout of electrical contacts on the chip to corresponding electrical contacts on the redistribution layer. The redistribution layer is formed to leave the optical fiber coupling region exposed. An optical fiber is connected to the optical fiber coupling region in optical alignment with the optical waveguide within the chip.

Ardalan, Shahab↗
DOE OSTI2022

Fiber and bundle orientations, matrix rich regions, and mechanical properties of fiber reinforced composites using thermal digital image correlation

Methods for assessing fiber and bundle orientations and mechanical properties of fiber reinforced composite materials using Thermal Digital Image Correlation (TDIC) are disclosed. In some examples, the method comprises exposing the composite material to a temperature change; imaging the composite material at a plurality of time points before, during and/or after the temperature change; and assessing the characteristic of the composite material based on the imaging. In others, temperature changes naturally occur during the cooling process after manufacturing can be employed for this method such as compression molding process, injection molding process, resin transfer molding processes and its variants.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Water soluble barrier coatings for washout tooling for a composite layup

A washout tooling for a composite layup is provided. The washout tooling comprises a casting mold having an exterior surface. The casting mold comprises a particulate material and a water-soluble binder. The casting mold is adapted to break down in the presence of an aqueous solution. The washout tooling further comprises a water-soluble coating layer overlying the exterior surface. The water-soluble coating layer is adapted to break down in the presence of an aqueous solution. The washout tooling further comprises a curable composite layer overlying the water-soluble coating layer. The water-soluble coating layer minimizes contact between the particulate material and the curable composite layer.

Saito, Tomonori↗
DOE OSTI2023

Method for micromolding a polymeric membrane having a pore array

A method for micro-molding a polymeric membrane and including pouring a predetermined volume of curable polymer unto a micro-fabricated mold having a post array with pillars, and overlaying the polymer with a support substrate. A spacer, such as a rubber spacer, is placed in contact with the support substrate and a force is applied to an exposed side of the spacer to compress the support substrate and the polymer together. While applying the force, the polymer is cured on the mold for a predetermined time period and at a predetermined temperature to form a polymeric membrane having a pore array with a plurality of pores corresponding to the plurality of pillars of the post array. The polymeric membrane is removed from the support substrate.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Fiber attach enabled wafer level fanout

A package assembly includes a silicon photonics chip having an optical waveguide exposed at a first side of the chip and an optical fiber coupling region formed along the first side of the chip. The package assembly includes a mold compound structure formed to extend around second, third, and fourth sides of the chip. The mold compound structure has a vertical thickness substantially equal to a vertical thickness of the chip. The package assembly includes a redistribution layer formed over the chip and over a portion of the mold compound structure. The redistribution layer includes electrically conductive interconnect structures to provide fanout of electrical contacts on the chip to corresponding electrical contacts on the redistribution layer. The redistribution layer is formed to leave the optical fiber coupling region exposed. An optical fiber is connected to the optical fiber coupling region in optical alignment with the optical waveguide within the chip.

Ardalan, Shahab↗
DOE OSTI2024

Investigation of the notch sensitivity of tailorable long fiber discontinuous prepreg composite laminates

Tailorable discontinuous fiber composite laminates provide relative formability beyond that of continuous fiber laminates, while achieving improved mechanical performance over comparable stochastic systems. Here, in this work, the notch sensitivity of engineered prepreg platelet molded composite (PPMC) laminates is investigated using the open-hole tension (OHT) test and compared to available data for stochastic PPMCs and continuous fiber laminates made with the same material. The press-formed thermoplastic composites (AS4/PEKK) were molded with a quasi-isotropic stacking sequence. The discontinuous PPMC laminate was found to be notch insensitive with OHT strengths ranging from 145.4 MPa (CV $=$ 7%) for d/w $=$ 0.5 to 229.3 MPa (CV $=$ 9%) for d/w $=$ 0.25. The highly ordered meso-structure of the engineered PPMC laminate yields comparatively excellent mechanical properties for relatively thin laminates in contrast to stochastic systems. Both net- and gross-section failures were observed for d/w $=$ 0.25, which suggests that the engineered PPMC laminates studied here maintain a degree of inherent, internal stress concentrations that compete with those caused by geometric features such as a circular hole. Computational simulations of the OHT tests with explicitly represented platelets were found to be in good agreement with experimental measurements. The progressive failure analysis was used to conduct a numerical investigation of the stacking sequence and platelet meso-morphology.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Assessment of Different Application Grades of Post-Consumer Recycled (PCR) Polyolefins from Material Recovery Facilities (MRFs) in the United States

The recycling of plastics has been gaining traction in the following years as many companies, organizations, and governments are pushing toward a more circular economy. However, plastic recycling rates are still small compared to those of plastic production, especially for polyolefins, such as high-density polyethylene (HDPE) and polypropylene (PP). With the goal of finding applications for recycled plastic resin, recyclers can face some challenges associated with the heterogeneity in the polymer properties of plastic waste streams, which could hinder the full potential of recycling due to the lack of a consistent feedstock. Here, this study assessed how an additional sorting step of recycled HDPE and PP streams, separating them into two categories based on the previous application, impacts the recycled polymer properties, such as physical, molecular, and thermal. It was demonstrated that manually separating HDPE articles previously processed by extrusion blow molding (EBM) or injection molding (IM) and PP articles by thermoforming (TF) or IM could yield recycled resins with more consistent properties, considering the significant differences between them. This highlights that an additional sorting step would allow recyclers to target more premium or currently unattainable plastic processing applications with postconsumer recycled (PCR) resins, which could significantly promote an increase in plastic recycling rates. Nevertheless, the development of new technologies is needed to automate this extra sorting step, as with the increase in scale manual sortation could not be feasible and cost-effective, reducing the attractiveness of using PCR resins in comparison to virgin ones.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Uncertainty quantification of fiber orientation distribution measurements for long-fiber-reinforced thermoplastic composites

We present a detailed methodology for experimental measurement of fiber orientation distribution (FOD) in injection-molded discontinuous fiber composites using the method of ellipses on 2D cross sections. Best practices to avoid biases occurring during surface preparation and optical imaging of carbon-fiber-reinforced thermoplastics are discussed. A marker-based watershed transform routine for efficient image segmentation and the separation of touching fiber ellipses is developed. The sensitivity of the averaged orientation tensor to the image sample size is studied for the case of long-fiber thermoplastics. A Mori-Tanaka implementation of the Eshelby model is then employed to quantify the sensitivity of elastic stiffness predictions to biases in the FOD measurements.

fiber orientation distribution measurement↗
DOE OSTI2021

Multi-Process Tooling

Decisions made early in the automotive design process influence material selection, which in turn dictates process selection and tool design. Because of tool build time and cost of tooling, the original path is not easily altered, even if there is compelling evidence that another material or process would be beneficial. This project focused on tool design that is agile enough to allow its use in multiple processes—injection, injection compression, and extrusion-compression. This tool design allows for the manufacture of components with the most efficient process or materials, without building multiple, single-process tools. The primary purpose of the Multi-Process Tool project was to physically demonstrate that a single, well-designed tool could be used to manufacture parts with a variety of materials that require different processes. A multi-process tool would be beneficial to providing data for any changes to the process since materials and processes can be interchanged without incurring additional tool cost(s). Battery tray parts, (representative of a multi-process tool, were successfully manufactured using various types of materials, such as fiber reinforced (carbon fiber and/or glass fibers, recycled carbon fibers), amorphous (PP, TPU), semi-crystalline (PA6, PA66), and crystalline (thermoset epoxy resin) polymers. Processing of the parts was achieved by injection molding, compression molding, compression overmolding, and injection overmolding. Specimens extracted from various locations on the battery tray parts were evaluated for mechanical properties (flexure and interlaminar shear strength properties). The results show that the tool can be used to produce parts from a wide range of materials and processes with no degradation of the physical or cosmetic properties.

42 ENGINEERING↗